JVC VN-X35U Instructions Manual

JVC VN-X35U Instructions Manual

Jvc megapixel ip camera instructions
Hide thumbs Also See for VN-X35U:
Table of Contents

Advertisement

MEGAPIXEL IP CAMERA
VN-X35U
INSTRUCTIONS
Thank you for purchasing this JVC product.
Before operating this unit, please read the
instructions carefully to ensure the best
possible performance.
LST0789-001A

Advertisement

Table of Contents
loading

Summary of Contents for JVC VN-X35U

  • Page 1 MEGAPIXEL IP CAMERA VN-X35U INSTRUCTIONS Thank you for purchasing this JVC product. Before operating this unit, please read the instructions carefully to ensure the best possible performance. LST0789-001A...
  • Page 2: Getting Started

    If you wish to dispose of this product, please visit our web page Union. www.jvc-europe.com to obtain information about the take-back of the product. [Other Countries outside the European Union] If you wish to dispose of this product, please do so in accordance with applicable national legislation or other rules in your country for the treatment of old electrical and electronic equipment.
  • Page 3 UL to be used for Burglar Alarm Functionality. This manual describes detailed usage of VN-X35U. For basic usage of VN-X35U, please refer to Read me first . For latest information, please refer to Readme file in the CD-ROM.
  • Page 4: Important Safeguards

    Getting Started These are general IMPORTANT SAFEGUARDS and certain items may not apply to all appliances. 1. Read all of these instructions. 2. Save these instructions for later use. 3. All warnings on the product and in the operating instructions should be adhered to. 4.
  • Page 5: Table Of Contents

    Focus Assist Mode ... 24 Network Requirements ... 24 Network Settings IP Address Settings ... 27 Setting the IP address for VN-X35U ... 27 IP address setting at the computer ... 28 Internet Explorer Setting ... 29 Changing the IP address using the Internet Explorer ...
  • Page 6: Main Features

    Getting Started Main Features High Picture Quality The camera unit of this product employs a 1,250,000-pixel CCD (1/3") which enables high quality video surveillance. Support for Dual Stream Simultaneous distribution of JPEG and MPEG4 images is possible. Realization of High Frame Rate Data transmission is possible in Quad-VGA size at a rate of 15 fps.
  • Page 7: Operating Environment

    ● Delay in the MPEG4 playback images and ● Sound might not be played back properly. ● To make use of Built-in MPEG4 Viewer of VN-X35U, install “ffdshow” that is open source codec. You can download “ffdshow” from the Internet.
  • Page 8: Cautionary Notes

    Exemption of Liability The motion detection feature is not a feature to prevent theft or fire. JVC shall not be liable for any damage that occurs. JVC shall not be liable for any damage due to the invasion of privacy by images of this camera.
  • Page 9 Others The cable stopper of the alarm terminal may come off in some cases. When mounting the cables, make sure to do so carefully. If a high luminance object (such as a lamp) is shot, a white smear may appear at the upper and lower ends of this object on the screen.
  • Page 10: Name And Function Of Parts

    Getting Started Name and Function of Parts Front / Bottom / Side Back Focus Adjustment Ring This ring is used for adjusting the back focus. To operate, loosen the H back focus fastening screw by turning it in the anti-clockwise direction, and turn the screw in the clockwise direction to fasten after operation is complete.
  • Page 11: Side

    Side [MONITOR OUT] Monitor Output Selection Switch Use this switch to select the availability of output from the N [MONITOR OUT] terminal as well as the signal system.(A Page 12) NTSC : Outputs NTSC signals. : No output. Select this value when distributing images to the network.
  • Page 12: Rear

    Getting Started Name and Function of Parts (continued) Rear [MONITOR OUT] Monitor Video Signal Output Terminal (RCA) This is an output terminal for composite video signals (1 V (p-p), output impedance of 75 K). Use this terminal to connect to devices such as a video monitor.
  • Page 13: Features

    Surveillance Using Built-in Viewer VN-X35U comes with Built-in JPEG/MPEG4 Viewer and Audio Monitor. JPEG images and MPEG4 images of VN-X35U can be monitored using Built-in Viewer on the JPEG images that are currently displayed can also be captured in the computer’s hard disk.
  • Page 14 VN-X35U MAC address Sending JPEG images before and after alarm input to FTP Restrictions on Clients VN-X35U enables users to authorize or reject the acquisition of images by specific IP address. Headset (A Page 70) Control via customized application software...
  • Page 15: Setup Procedures

    Step 2 Network settings (A Page 27) Configure the network settings of the computer and this camera. T In a system where multiple units of VN-X35U are used, turn on the power of only one unit to configure the IP address settings using the Internet Explorer.
  • Page 16: Connection / Installation

    ● Make use of a megapixel lens. Check the mounting method of the lens to be used before mounting ● The mount method used for VN-X35U is CS mount. ● Make use of the values listed in the table below for the dimensions of the lens mount (a) indicated in the following diagram.
  • Page 17: Power Connection

    Please contact our service center immediately for servicing (charged separately). ● After DHCP timeout, all IP addresses of VN-X35U are set to 192.168.0.2 by default. When the power of multiple cameras within the same LAN environment are turned on at the same time, the IP address of the cameras overlap, thus preventing proper access.
  • Page 18: Using The Poe

    Connection / Installation Power Connection (continued) ● In a system where multiple units of VN-X35U are used, turn on the power of only one unit to configure the IP address settings using the Internet Explorer. Upon doing so, turn on the power of the second unit and configure accordingly.
  • Page 19: Monitor Signal Output Terminal Connection

    Monitor Signal Output Terminal Connection Make use of this terminal for camera angle adjustment during installation or focus adjustment in the Focus Assist mode. Connect it to devices such as a video monitor using a video cable (RCA). Memo: ● It is convenient to adjust focus using focus assist mode.
  • Page 20: Alarm Input/Output Terminal Connection

    (A Page 57) (Alarm Output Equivalent Circuit) Note: ● Connect the G terminal of this camera to the GND terminal of the annunciating device or alarm input sensor. VN-X35U DC3.3 V INPUT 1 or 2 Terminal 3.3 V 1 mA G Terminal Relay Switch, etc.
  • Page 21: Mounting The Camera

    Mounting the Camera ● Use the screw hole on the camera mounting bracket to mount this camera to a fixer or rotating platform. Mount the fall prevention wire using the black screw at the rear of the camera unit. Camera Mounting Camera Mounting Screw Hole...
  • Page 22: Mounting To The Housing Using The Inner Tripod Base

    Connection / Installation Mounting the Camera (continued) Warning ● Special attention is required when mounting the camera to a wall or ceiling. Users should get professional contractors to perform mounting operations instead of doing it themselves. Failure to do so may cause the camera to fall off and result in injuries or accidents.
  • Page 23: Back Focus Adjustment

    Inner Tripod Base Mounting Screw Make use of 1/4-20UNC screw. The length of the mounting screw shall be between 6 mm to 7 mm from the mounting surface. Note: ● Using a screw with a length longer than specified may damage the internal parts of the camera, while using a length shorter than specified may cause the camera to fall off.
  • Page 24: Focus Assist Mode

    ● Data volume to be sent by VN-X35U varies with the settings and number of distributions. ● The maximum bit rate for transmission is about 20 Mbps.
  • Page 25 The number of streams is the total number of streams sent via TCP (number of clients), streams sent via multicast, and stream received by VN-X35U (Example) When VN-X35U sends out 2 audio streams and receives 1 audio stream, data volume will be as follows.
  • Page 26 Network Delay When the client acquires JPEG via TCP, VN-X35U will send out data while checking the ACK from the client at the same time. For networks with considerable delay, data cannot be sent out until ACK is received, and therefore the frame rate will drop.
  • Page 27: Network Settings

    ● For details on IP addresses assigned to VN-X35U, consult your network administrator. ● You can look up the IP address of VN-X35U using the search tool in the ATOOL_EB folder in the supplied CD-ROM. For details, please refer to the AReadmeB file in the ATOOL_EB folder.
  • Page 28: Ip Address Setting At The Computer

    IP Address Settings (continued) IP address setting at the computer Set the computer to an IP address that enables communication with VN-X35U. Procedures described in this item are intended for Windows XP users. Click [Start] ● Select in the sequence of [Control Panel]-[Network Connection]-[Local Area].
  • Page 29: Internet Explorer Setting

    Internet Explorer Setting Launch the Internet Explorer on the computer When proxy settings are enabled in the Internet Explorer, follow the steps below to disable the proxy of the Internet Explorer ● Select in the order of [Tool]-[Internet Options]-[Connections]-[LAN Setting], followed by deselecting the check for [Use a proxy server for your LAN] under [Proxy Server] of the [Local Area Network (LAN) Settings] window.
  • Page 30: Changing The Ip Address Using The Internet Explorer

    IP address directly. In this case, change the proxy settings of the Internet Explorer. ● After the [Security Settings] screen appears, press the [OK] button to proceed. Enter the user name and password (login as administrator) VN-X35U Enter the user name. This is set to AadminB by default. Enter the password.
  • Page 31 Built-in Viewer of VN-X35U is displayed The operator password entry screen appears Enter operator password (default is AjvcB). Click [OK]. Memo: ● The operator password entry screen does not appear if the password is stored on the computer.Go to Step 5.
  • Page 32 Memo: ● Access from this computer may fail when the IP address of VN-X35U is changed. To enable access to VN-X35U from the same computer, alter the IP address at the computer accordingly.
  • Page 33: Setting Using Internet Explorer

    VN-X35U is unknown. In this case, you can obtain information on the IP address using the following method. ● You can look up the IP address of VN-X35U using the search tool in the ATOOL_EB folder in the supplied CD-ROM.For details, please refer to the AReadmeB file in the ATOOL_EB folder.
  • Page 34 [Enable]. Enable also [Allow Script-initiated window without size or position constraints.] under [Miscellaneous]. Disable pop-up block Connection of VN-X35U cannot be established when pop-up block in the Internet Explorer is set to AEnableB. Follow the steps below to set the pop-up block to AdisableB.
  • Page 35: Enter User Name And Password

    AEnableB for [Miscellaneous]-[Display mixed content]. Note: ● Do not reset or turn off the power of VN-X35U immediately after the settings are changed. Otherwise, changes may not be saved, and VN-X35U may be restored to the factory settings.
  • Page 36: Setting

    Setting Using Internet Explorer Setting How to open the setting page Enter IP address of VN-X35U in the address bar of Internet Explorer (A Page 30) ● A unified viewer is opened. Click [Detalis]. ● [Basic Settings1] page will be opened if accessed by user nameAadminB.(A Page 37) ●...
  • Page 37: Basic Settings1

    The time transmitted by VN-X35U is recorded in the JPEG header. Discontinuity may occur in the JPEG header's time immediately before and after changing the time. For setting the time zone. Click the [Set] button to set the time of the computer on VN-X35U.
  • Page 38: Basic Settings2

    Setting Using Internet Explorer Setting (continued) Basic Settings2 Page for setting fundamental parameters of ACameraB, AJPEGB and AMPEG4B. This page can be used during access using AadminB or AoperatorB. ● Click [Basic Settings2]. ● Press the [OK] button to enable the new settings. ●...
  • Page 39 Camera ID Character strings entered here will be written to the JPEG comment segment (item name: camera). Refer to the API Guide on the file formats of JPEG. Monitor Type For selecting the monitor type according to the monitor used to display the video images.
  • Page 40 Setting Using Internet Explorer Setting (continued) Basic Settings2 (continued) JPEG Frame Size MPEG4 Bitrate Bitrate Control I Frame Interval Priority For specifying the JPEG picture quality (rate control mode) and size (target file size). When AVFS1B to AVFS7B is selected, the quantization table during JPEG encoding will be maintained and the file size will increase/decrease according to the input signals.
  • Page 41: Camera Page

    Camera Page This page is for setting the camera’s parameters. This page can be used during access using AadminB or AoperatorB. ● Click [Advanced Settings] to display setting menu. ● Click [Camera]. ● Press the [OK] button to enable the new settings. ●...
  • Page 42 Setting Using Internet Explorer Setting (continued) Camera Page (continued) Camera ID Character strings entered here will be written to the JPEG comment segment (item name: camera). Refer to the API Guide on the file formats of JPEG. Monitor Type For selecting the monitor type according to the monitor used to display the video images.
  • Page 43 Color Level For adjusting the color level. Larger value Smaller value : Decreases the color level. [Setting values: -5 to 0 to 5] For setting the AGC (automatic gain control) level. High Super [Set values: Off, Mid, High, Super] Memo: ●...
  • Page 44 Setting Using Internet Explorer Setting (continued) Camera Page (continued) Shutter Speed For setting the shutter speed. Auto, Auto(1/15 - 1/100) 1/15 to 1/10000 Flickerless [Set values:Auto, Auto(1/15 - 1/100), 1/15, 1/25, 1/30, 1/50, 1/60, 1/100,1/250, 1/500,1/1000, 1/2000, 1/4000, 1/10000, Flickerless] Memo: ●...
  • Page 45 White Balance For selecting the white balance control feature. White balance can be adjusted for a light source with a color temperature range of 2800K to 9500K. Switches to the Auto-Tracking White Balance (automatic color temperature tracking) mode. Adjusts the white balance automatically according to the color temperature of the light.
  • Page 46: Encoding Page

    ● When settings on this page are altered during playback using Built-in Viewer, reboot the viewer. ● There is a maximum limit to the bit rate for transmission by VN-X35U. If a bit rate that exceeds the maximum limit is specified, this new setting will not be applied. For details on the maximum transmission limit, refer to the section on ANetwork RequirementsB (A Page 24).
  • Page 47 Frame Size JPEG Quality/Size MPEG4 Bitrate Bitrate Control Frame Rate I Frame Interval Priority For selecting the frame size of each JPEG or MPEG4 screen to Quad VGA (1280 960), VGA (640 Select one of the eight different patterns.(A Page 39) For specifying the JPEG picture quality (rate control mode) and size (target file size).
  • Page 48: Audio Page

    Setting Using Internet Explorer Setting (continued) Audio Page This page is for setting the audio parameters. This page can be used during access using AadminB or AoperatorB ● Click [Advanced Settings] to display setting menu. ● Click [Audio]. ● To enable the new settings, press the [OK] button. Click...
  • Page 49 Press the [Browse] button to show the file selection screen and make a selection from the available audio files. Press the [Play] button to play back an audio file registered on VN-X35U, and send output to the Audio signal output terminal of VN-X35U.
  • Page 50: Alarm Page

    Setting Using Internet Explorer Setting (continued) Alarm Page This page is for setting actions when there is an alarm. Up to 5 actions (No. 01 to No. 05) may be set. This page can be used during access using AadminB or AoperatorB. ●...
  • Page 51 Output 2 Make Output 2 Break Position Play Audio : Play back an Audio File registered on VN-X35U. (A Page 49) 1st Trigger For specifying the first trigger to be activated. [Set values:Input 1 Make, Input 2 Make, Input 1 Break, Input 2 Break,...
  • Page 52 Setting Using Internet Explorer Setting (continued) Alarm Page (continued)
  • Page 53 Max. Interval Enabled when both the first and second triggers are specified. Specify the maximum interval between the first and second triggers. An action will be invoked only if the interval between the first and second triggers is within the maximum interval. 2nd Trigger For specifying the second trigger for invoking an action.
  • Page 54: Alarm Environment Page

    Setting Using Internet Explorer Setting (continued) Alarm Environment Page This page is for setting alarm-related environments. This page can be used during access using AadminB or AoperatorB. ● Click [Advanced Settings] to display setting menu. ● Click [Alarm Environment]. ● Press the [OK] button to enable the new settings. ●...
  • Page 55 Mail For setting the mail environment when [Mail] is specified as an action on the Alarm page.[SMTP] and [POP] can be used. Configure only the [SMTP] settings under usual circumstances. Enter the camera’s mail address as the recipient’s mail address. Configure the [POP] settings as well if [POP before SMTP] is enabled.
  • Page 56 Setting Using Internet Explorer Setting (continued) Alarm Environment Page (continued)
  • Page 57 Time Filter: For specifying the periodic FTP transfer action with respect to each day of the week and setting the corresponding time of the day. Applicable day of week : Sunday, Monday, Tuesday, Wednesday, Alarm action Applicable time period : For specifying the start and end time in hours and Pre-/Post-recording parameter: [PrePostRecording Frame Rate] [PrePostRecording Before Trigger] : For setting the FTP pre-recording...
  • Page 58: Ptz Page

    Setting Using Internet Explorer Setting (continued) PTZ Page Set the movement for AAuto ReturnB, AZoom LimitB and APreset PositionB. This page can be used during access using AadminB or AoperatorB.. ● First of all, configure the encoding settings.(A Page 39) ●...
  • Page 59: Auto Patrol Page

    Auto Patrol Page Perform Auto Patrol setting to switch image display between multiple positions according to the interval that has been set.Set when viewing registered positions in order. This page can be used during access using AadminB or AoperatorB. ● First of all, configure the encoding settings.(A Page 39) ●...
  • Page 60 Setting Using Internet Explorer Setting (continued) Auto Patrol Page (continued) Click Switches the camera images in sequence from No. 0 to No. 19. Title Shows the title of the position. Position For setting the sequence of position numbers in which the camera moves. [Set values : 0 to 19] Stay Time For setting the time interval for displaying the image of the respective positions.
  • Page 61: Privacy Mask Page

    Privacy Mask is a feature that enables masking of a portion of the image. VN-X35U enables unlimited privacy masks to be specified in different shapes at your favorite locations. The Privacy Mask masks area by uploading a BMP file painted in red (created separately). The displayed color is determined by the color specified on this page.
  • Page 62 Press the [Browse...] button to display the file selection screen. Select the BMP file in the PC. Press the [Upload] button to upload the selected BMP file to VN-X35U. Creating the BMP file 1. Upon installing the camera, use JPEG Viewer to save the JPEG file on the computer.
  • Page 63: Motion Detection Page

    Motion Detection Page This page is for setting motion detection. This page can be used during access using AadminB or AoperatorB. ● Click [Advanced Settings] to display setting menu. ● Click [Motion detection]. ● The area valid for motion detection is displayed in blue. ●...
  • Page 64 Our company shall not be liable for any accident or damage that occurs. ● When images on VN-X35U are currently acquired by another client or Built-in Veiwer, video images may not appear on the [Motion Detection] page due to the maximum distribution limit of VN-X35U.
  • Page 65: Network Basic Page

    Connect VN-X35U to a network environment with a DHCP server when DHCP is to be enabled. If the DHCP server does not exist when DHCP is set to AEnableB, VN-X35U will start running with the 192.168.0.2 IP address and 255.255.255.0 subnet mask in about 2 minutes after startup.
  • Page 66: Network Details Page

    [Setting range: 1280 to 1500] For setting the negotiation of the network. When a value other than AAutoB is selected, do not set the network device to be connected to AAutoB. Ensure that it is set to the same value as VN-X35U.
  • Page 67: Protocol Page

    ● After changing, you will need to re-establish the connection if you are using the Internet Explorer. Click HTTP Server You can change the port number for the built-in web server of VN-X35U. (1 to 65535: The default port number setting is 80.) Port The JPEG and MPEG4 HTTP port number for the web server will also be changed.
  • Page 68: Streaming Page

    Setting Using Internet Explorer Setting (continued) Streaming Page This page is for setting manual multicast transmission. This page can be used during access using AadminB or AoperatorB. ● Click [Advanced Settings] to display setting menu. ● Click [Streaming]. ● Press the [OK] button to enable the new settings. ●...
  • Page 69 Multiple multicast streams cannot be received on a single computer when there are duplicate port numbers. Memo: ● When the power of VN-X35U shuts down accidentally during multicast transmission, multicast transmission will restart automatically after VN-X35U is rebooted.
  • Page 70: Access Restrictions Page

    Setting Using Internet Explorer Setting (continued) Access Restrictions Page This page is for setting client restrictions. This page can be used during access using AadminB. ● Click [Advanced Settings] to display setting menu. ● Click [Access Restrictions]. ● Press the [OK] button to enable the new settings. ●...
  • Page 71 ● Note that when AallowB is selected and all IP address fields are left blank, JPEG/MPEG4 acquisition by all IP addresses will be denied. Restrictions are not imposed on access to the Web Settings page. Additionally, VN-X35U will also deny access when instructions for transmission to the specified IP address are sent via API. Memo: ●...
  • Page 72: Time Page

    The clock time can be changed by entering an appropriate value. (Second value cannot be specified.) In addition, time will be recorded in the JPEG headers distributed by VN-X35U. Discontinuity may occur in the JPEG header’s time immediately before and after changing the time. Time Zone For setting the time zone.
  • Page 73: Password Page

    VN-X35U is case sensitive. New Password Enter again to confirm the new password. Again Note: ● Be sure to handle the password carefully in case you forget it. ● In the event that you forget the password, please consult JVC’s servicing center.
  • Page 74: Maintenance Page

    Update Upgrades the firmware version of VN-X35U and reboots the unit. The settings of VN-X35U will be saved. Copy the new firmware file to the computer on which Internet Explorer is used, and specify this file using the [Browse...] button. Press the [Update] button to start the update. JPEG/ MPEG4 transmission and all others services that are running will be discontinued.
  • Page 75: Led State Page

    LED State Page This page is for setting the method for lighting the [STATUS] indicator at the side of VN-X35U. This page can be used during access using AadminB or AoperatorB. ● Click [Advanced Settings] to display setting menu. ● Click [LED State].
  • Page 76: List Of Factory Settings Of Each Page

    MPEG4 I Frame Interval MPEG4 Priority Audio Page (A Page 49) Duplex Mode Mike GainMENU OFF Mike Power Supply Factory Settings Audio File 1 VN-X35U Audio File 2 Custom Audio File 3 Audio File 4 Audio File 5 High Alarm Page(A Page 51)
  • Page 77 Alarm Environment Page(A Page 54) Item SMTP Server Port Number Send Mail Address POP before SMTP POP Server Port Number Username FTP Server Directory Username Periodic FTP Periodic FTP Interval Periodic FTP Naming Periodic FTP Time Filter PrePostRecording Frame Rate PrePostRecording Before Trigger PrePostRecording After...
  • Page 78 Factory Settings LED State Identify Unit Item Factory Settings deny — Item Factory Settings 0.0.0.0 hour, 1 (GMT) UTC Item Factory Settings AadminB Blank Default passwords are: AadminB : jvc AoperatorB : jvc AuserB : jvc Item Factory Settings Enable...
  • Page 79: Miscellaneous Page

    This page can be used during access using AadminB, AoperatorB and AuserB. ● Click [Advanced Settings] to display setting menu. ● Click [Miscellaneous]. Click Open Source Press the [Show] button to display information of the software used by VN-X35U. Software...
  • Page 80: Operation Page

    ● Click [Advanced Settings] to display setting menu. ● Click [Operation]. Click Total Sending Displays the total TCP/UDP bit rate sent by VN-X35U as well as the individual bit rates. Bitrate Destination Displays the destination that VN-X35U is sending data to.
  • Page 81: Settings Page

    Settings Page Display the version information and current settings of VN-X35U. This page can be used during access using AadminB or AoperatorB. ● Click [Advanced Settings] to display setting menu. ● Click [Settings]. Click...
  • Page 82 Setting Using Internet Explorer Setting (continued) Settings Page (continued)
  • Page 84: Position List

    Setting Using Internet Explorer Setting (continued) Position List The Position List displays information on the preset positions. This page can be used during access using AadminB or AoperatorB. ● Click [Advanced Settings] to display setting menu. ● Click [Position List]. Click...
  • Page 85: Patrol Infomation

    Patrol Infomation Patrol Information displays the Auto Patrol information and settings. This page can be used during access using AadminB or AoperatorB. ● Click [Advanced Settings] to display setting menu. ● Click [Patrol Infomation]. Click...
  • Page 86: Operation

    Operation Operation of Built-in Viewer VN-X35U comes equipped with an integrated viewer. You can start up Built-in Viewer by entering the IP address in the Internet Explorer. Built-in Viewer enables you to performing monitoring using JPEG or MPEG4 images, audio transmission, and PTZ operations.
  • Page 87 ● Click [Trusted sites] under [Tool]-[Internet Options]-[Security]. Upon doing so, the [Sites…] button directly below becomes active. Click this button and deselect the check in the displayed window. Next, add the IP address of VN-X35U. If the setting is factory default, add the following web site to the zone.
  • Page 88: Installing Built-In Viewer

    Operation Operation of Built-in Viewer (continued) Installing Built-in Viewer Enter IP address of camera in the address bar ofInternet Explorer Enter the following IP address into the address field. http://192.168.0.2 Click [Go]...
  • Page 89 Enter the user name and password VN-V25 The viewer is installed and launched Enter the user name. This is set to AadminB by default. Enter the password. This is set to AjvcB by default. Click [OK].
  • Page 90: Screen Configuration

    ● In the case of AWindows VistaB, images are stored under [Documents]. ● The folder name can be changed. (A Page 99) Note: ● The time indicated is the computer's clock time,not the clock ATimeB of VN-X35U. ● Motion images cannot be captured. ● MPEG4 images cannot be captured.
  • Page 91 ● Deleting this file deletes the view settings, and the viewer will be initialized during the next startup. Starts sending audio sound to VN-X35U from the client PC. Only one stream of audio sound can be sent for one unit of VN-X35U You cannot send audio sound from a client PC when transmission of audio sound from a different client PC is in progress.
  • Page 92: Image Quality Setting

    Operation Operation of Built-in Viewer (continued) Image quality setting Below are procedures for configuring the Image settings. ● When a different menu is currently being displayed, click [Control] to switch the viewer. ● Click each menu bar on the left of the screen to open the setting screen.. Image Settings Click...
  • Page 93 ● Focus assist mode will be disabled after 3 minutes if left unattended. ● Focus assist mode can be enabled using the button at the side of VN-X35U. : Switches to the Auto-Tracking White Balance (automatic color temperature tracking) mode. Adjusts the white balance automatically according to the color temperature of the light.
  • Page 94: Ptz Setting

    Operation Operation of Built-in Viewer (continued) PTZ setting This page describes procedures for setting the preset positions. ● When a different viewer is currently being displayed, click [Control] to switch the viewer. ● Click the menu bar on the left side of the screen to open the setting screen. PTZ Settings Click...
  • Page 95 Preset Position For setting the preset positions. For selecting a APositionB. Position [Set values :HOME , 1 to 19] Title Displays the current title. Enter accordingly if you want to register or change a title. (You can enter up to 32 alphanumeric. AJPEG ViewerB displays up to only 16 alphanumeric.) Press [Reaiste] button to complete position registration.
  • Page 96: Ptz Control

    Operation Operation of Built-in Viewer (continued) PTZ Control Use this item to operate the PTZ feature. Settings can be configured on the PTZ Settings . (A Page 94) ● When a different menu is currently being displayed, click [Control] to switch the viewer. ●...
  • Page 97 Start UNCTION Stop Preset For selecting a Preset Position, or move to the selected Position if that Position has already been registered. Position [Set values : HOME , 1 to 19] Pan/Tilt/ Pan/Tilt operation Zoom Click the arrow buttons to move the display area in the direction indicated by the arrow.
  • Page 98: Jpeg Viewer Settings

    Select AOnB to display [Camera ID]. [Camera ID] can be specified on the[Basic Settings2] or [Camera] page of VN-X35U. Selecting AOnB displays the position title. When AOnB is selected, the frame of the video image display area where motion is detected turns red.
  • Page 99 Stream Settings For specifying settings for receiving JPEG stream. Stream For selecting the protocol when the viewer acquires data from VN-X35U. When AHTTPB is selected, lost packets are recovered via resending. VN-X35U may be monitored using multiple viewers when AMulticastB is selected.
  • Page 100: Mpeg4 Viewer Settings

    ● Click the menu bar on the left side of the screen to open the respective setting screens. Memo: ● To make use of Built-in MPEG4 Viewer of VN-X35U, you will need to install the ffdshow open source codec. You can obtain ffdshow through the Internet.
  • Page 101 Stream Settings For specifying settings for receiving MPEG4 stream. Stream For selecting the protocol when the viewer acquires data from VN-X35U. When AHTTPB is selected, lost packets are recovered via resending. VN-X35U may be monitored using multiple viewers when AMulticastB is selected.
  • Page 102: Audio Monitor Settings

    Operation Operation of Built-in Viewer (continued) Audio Monitor Settings This page describes procedures for configuring the settings to send/receive audio sound using the JPEG and MPEG4 Viewers. ● When a different menu is currently being displayed, click [Viewer Setup] to switch the viewer. ●...
  • Page 103 Common For specifying the HTTP port settings HTTP Port For changing the port number during access to VN-X35U from the client PC via HTTP. The default port number is 80. Specify the same value as the parameter that is set on the Protocol.
  • Page 104: Operator Password

    Operation Operation of Built-in Viewer (continued) Operator Password Follow the procedures below to configure the operator password required for sending/receiving audio sound or PTZ operation. ● When a different menu is currently being displayed, click [Viewer Setup] to switch the viewer. ●...
  • Page 105: Exiting The Viewer

    To exit, press the [ ] button at the top right of the window. ● During the next startup of Built-in Viewer, launch the Internet Explorer and enter the URL of Built-in Viewer in the address field. For example, if the IP address of VN-X35U is 192.168.0.2, enter as follows: http://192.168.0.2/cgi-bin/x35viewing.cgi?x35ptzviewer.html Memo: ●...
  • Page 106: Others

    Built-in Viewer. The maximum number of images that can be sent by VN-X35U via TCP is 20, and up to 20 Built-in Viewers can be connected to each VN-X35U unit. Make use of multicast for monitoring when the number of areas exceeds the above number.
  • Page 107 ● Check whether the switch at the side of VN-X35U is set to or . If either of the above is selected, change the switch setting to . After changing the switch settings, press the [RESET] button to reboot.
  • Page 108 [Countermeasure] To make use of Built-in MPEG4 Viewer of VN-X35U, install “ffdshow” that is open source codec. You can download “ffdshow” from the Internet. ● Set the switch to or , and press the Reset button.
  • Page 109: Specifications

    Specifications Camera Unit Pick-up element : 1/3-inch progressive scan Effective pixels : Approx. 1,250,000 pixels 1296(H) Lens Mount : CS mount [Monitor Output] Composite video x 1 (75 K, 1 Vp-p) Minimum object illumination (Shutter 1/30): : 0.66 lx (50 %, F1.0, AGC Super) : 0.33 lx (25 %, F1.0, AGC Super)
  • Page 110 Others Specifications (continued) Dimension [Unit: mm (inch)] T Specifications and appearance of this product are subject to changes for improvement without prior notice. U1-32 65 (2-9/16) 42 (1-5/8) 66 (2-5/8) 30 (1-3/16) 126 (5) 115 (4-9/16) 1/4 – 20UNC...
  • Page 111 LST0789-001A © 2008 Victor Company of Japan, Limited...

This manual is also suitable for:

Vn-x35ul - network camera

Table of Contents