Makita GN900 Instruction Manual
  1. Manuals
  2. Brands
  3. Makita Manuals
  4. Nail Gun
  5. GN900
  6. Instruction manual

Makita GN900 Instruction Manual

Cordless clipped head framing nailer
Hide thumbs Also See for GN900:
Table of Contents

Advertisement

Quick Links

See also: Instruction Manual
INSTRUCTION MANUAL
Cordless Clipped Head Framing
Nailer
GN900
009440
IMPORTANT: Read Before Using.
1

Advertisement

Table of Contents
loading

Related Manuals for Makita GN900

Summary of Contents for Makita GN900

  • Page 1 INSTRUCTION MANUAL Cordless Clipped Head Framing Nailer GN900 009440 IMPORTANT: Read Before Using.

  • Page 2: Specifications

    ENGLISH (Original instructions) SPECIFICATIONS Model GN900 Nail length X Shank diameter Nail L :50 mm - 90 mm d : 2.9 mm - 3.3 mm Nail capacity 40 nails (1strip) Nail collation angle (degree) Figure of nail head Clipped Dimensions (L X H X W)

  • Page 3: General Power Tool Safety Warnings

    Distractions can cause Makita Corporation responsible you to lose control. manufacturer declare that the following Makita Electrical safety machine(s): Power tool plugs must match the outlet. Never Designation of Machine: modify the plug in any way. Do not use any...

  • Page 4: Important Safety Instructions

    Use the tool only with the Makita genuine fuel cell. • power tool’s operation. If damaged, have the Never use the tool in enclosed or poorly ventilated •...

  • Page 5: Always Assume That The Tool Contains Fasteners

    working area. and litter-free. Be especially careful to maintain For Australia and New Zealand only good footing and balance. • Always wear safety glasses and face shield to Only those involved in the work should be in the • protect your eyes from dust or nail injury. The safety vicinity.
  • Page 6 Do not store the tool and battery cartridge in • Makita. locations where the temperature may reach or Ask Makita's Authorized service centers for exceed 50 ﾟ C (122 ﾟ F). • periodical inspection of the tool. Do not incinerate the battery cartridge even if...

  • Page 7: Functional Description

    Overview of the nailer FUNCTIONAL DESCRIPTION CAUTION: Always be sure to remove the fuel cell, the battery • cartridge and nails before adjusting or checking function on the tool. Installing or removing battery cartridge 009441 Always switch off the tool before insertion or •...

  • Page 8: Adjusting The Nailing Depth

    Detach the cap (in case the metering valve is provided with the cap). 009450 Insert the jet nozzle into the small hole of the adapter properly. 009446 Push in the front edge. 009451 Put the fuel cover over the metering valve and push it 009447 Push in the rear edge until it seats.

  • Page 9: Operation

    Installing the hook 1. Hook 011695 Load nails so that they get parallel to the driver guide. 009457 The hook is convenient for hanging the tool temporarily. Removing nails The hook can be set in two positions according to where 1.

  • Page 10: Jammed Nailer

    Maintenance after daily work At the end of daily work, conduct an end-of-workday routine. These simple steps are based on maintaining the safety and performance of Makita Cordless Clipped Head 009460 Framing Nailer Loosen the (2) magazine mounting screws with Before leaving the work site: the hex wrench.

  • Page 11: Optional Accessories

    Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. Nails • Safety goggles • Fuel cell •...
  • Page 12 Makita Corporation Anjo, Aichi, Japan www.makita.com 884862D228...

Table of Contents