CONTENTS CONTENTS INTRODUCTION Unpacking the Telephone DESCRIPTION General Description INSTALLATION Setting Up Wall Mounting SETTINGS Ringer Settings Flash (Recall) Setting Receiving Voume and Tone Settings Speakerphone Volume Setting Sending Volume Setting USING THE TELEPHONE Making a Call Receiving a Call Last Number Redial Mute Function Hearing Aid Use...
Page 4
CONTENTS TROUBLESHOOTING SAFETY INFORMATION GUARANTEE RECYCLING DIRECTIVES...
It is important that you read the instructions below in order to use your Geemarc telephone to its full potential. Keep this user guide in a safe place for future reference. This guide explains how to use the following telephone:...
When unpacking the telephone, you should find the following in the box: • 1 CL1200 unit • 1 CL1200 handset with curly cord • 1 Telephone line cord • 1 User Guide For product support and help visit our website at www.geemarc.com...
DESCRIPTION General Description ringer LED (white) hook button in use LED (red) M1 to M3 one touch memory locations handset M4 to M19 hanger tab one touch memory locations flash time setting amplify LED numeric amplify button keypad memory flash button redial/pause hands free speaker...
Connect the handset to one end of the curly cord. Plug the other end of the curly cord into the jack on the left hand side of the CL1200 unit. Place the handset on the cradle. Connect the line cord to the jack located at the rear of the telephone.
INSTALLATION Wall Mounting Turn the handset hanger tab round (rotate it 180 degrees). This will keep the handset from falling out of the cradle when it is mounted on the wall. Install two screws at a distance of 83 mm from each other on a vertical line.
SETTINGS Ringer Settings A switch located on the rear of the CL1200 unit allows the ringer volume to be switched to HI (maximum volume), LOW (lowest volume) or OFF (if you would prefer not to be disturbed). A switch located on the rear of the CL1200 unit allows the ringer tone to be selected.
SETTINGS Receiving Volume and Tone Settings You can alter the receiving volume and tone during a conversation according to your hearing requirements. The handset earpiece volume may be adjusted during a call using the volume slide control found at the front of the telephone base.
Page 16
SETTINGS AMPLIFY ON/OFF Switch at ON Position The additional amplification and tone controls are automatically activated each time you use the telephone. The amplify LED light will be lit when you use the telephone. Pressing the Amplify button during a call will turn off the additional amplification and tone controls.
SETTINGS Tone Receiving Adjustment If the receiver volume has been amplified, the tone control can also be adjusted. You can adjust and increase the low frequency or high frequency sounds with the tone slide control on the top of the unit. Note: The tone adjustment function will not be affective when the receiver volume is set to normal level.
USING THE TELEPHONE Making a Call Pick up handset. The red LED indicator will light up When you hear the dialling tone, dial the number on the keypad To end the call simply replace the handset in the cradle Making a Call – Hands Free Press the button to get a dialling tone.
USING THE TELEPHONE USING THE TELEPHONE Receiving a Call When an incoming call is received, the telephone rings and the incoming call LED flashes. Lift the handset and speak. The red LED indicator will light up To end the call simply replace the handset in the cradle Receiving a call –...
USING THE TELEPHONE Hearing Aid Use This telephone is hearing aid compatible. Select the T mode on your hearing aid to enable this feature. Flash Signal The R button can be used with special services such as Call Waiting (if provided by your service provider) or transferring external calls to another extension within a private switchboard.
MEMORY Storing a Number to Memory The CL1200 has 19 one touch memory buttons. Pick up the handset Press Enter the telephone number you wish to store (up to 32 digits). If required, you can use to insert a pause Press again.
TROUBLESHOOTING CL1200 does not ring • Make sure that the telephone line cord is plugged in correctly and is not damaged • Connect another telephone to the telephone PTT socket or move your telephone to another socket to track if the failure is coming from your telephone or your PTT socket •...
SAFETY INFORMATION General Do not open the unit. Contact the helpline for all repairs. Cleaning Clean the telephone with a soft cloth. Never use polishes or cleaning agents - they could damage the finish or the electrics inside. Environmental Do not expose to direct sunlight. Always ensure there is a free flow of air over the surfaces of the telephone.
GUARANTEE From the moment your Geemarc product is purchased, Geemarc guarantee it for the period of one year. During this time, all repairs or replacements (at our discretion) are free of charge. Should you experience a problem then contact our help line or visit our website at www.geemarc.com.
Page 25
GUARANTEE Telephone connection: Voltages present on the telecommunication network are classified TNV-3 (Telecommunication Network Voltage) according to the EN60950 standard.
- Or, hand the old product to the retailer. If you purchase a new one, they should accept it. Thus if you respect these instructions you ensure human health and environmental protection. For product support and help visit our website at www.geemarc.com Telephone 01707 384438 Or fax 01707 372529 UGL1200_En_v1.2...