Wolf 30" Installation Manual
Pro wall ventilation hoods
Hide thumbs
Also See for 30":
- General information manual (85 pages) ,
- Installation manual (26 pages) ,
- Installation instructions manual (12 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for Wolf 30"
Summary of Contents for Wolf 30"
- Page 1 INSTALLATION GUIDE Pro Wall Ventilation Hoods...
-
Page 2: Table Of Contents
Contents Important Note Wolf Pro Wall Ventilation Hoods ....3 To ensure the safe and efficient use of Wolf equipment, please take note of the following types of highlighted Installation Considerations . -
Page 3: Wolf Pro Wall Ventilation Hoods
Wolf Pro Wall Ventilation Hoods wolfappliance.com/specs Pro Wall Hood Installation IMPORTANT NOTE: This installation must be completed Wolf Pro Wall Hood by a qualified installer or Wolf authorized service center Model Number technician. Serial Number Read this entire installation guide prior to installation and save for the local inspector’s reference. -
Page 4: Installation Considerations
Installation Considerations IMPORTANT INSTRUCTIONS Installation Considerations Pro wall hoods are recommended for use with all Wolf TO REDUCE THE RISK OF FIRE, ELECTRIC cooking appliances and should be at least as wide as the SHOCK OR INJURY, OBSERVE THE FOLLOWING: cooking surface. -
Page 5: Pro Wall Hood Specifications
Pro Wall Hood Specifications wolfappliance.com/specs Overall Dimensions LOW-PROFILE WALL HOODS 12" (305) 10" (254) OVERALL HEIGHT 4" (102) 22" 30" , 36" , 42" (559) (762) (914) (1067) 48" (1219) WIDTHS OVERALL DEPTH 24" DEEP WALL HOODS (610) 12" (305) 18"... - Page 6 Pro Wall Hood Specifications Installation Specifications LOW-PROFILE WALL HOODS 6" LOCATION OF ELECTRICAL (152) 5" 10" (254) (127) HEIGHT OF HOOD WIDTH OF HOOD 30" 36" 22" (762) TO (914) (559) TO COUNTERTOP DEPTH OF HOOD 24" AND 27" DEEP WALL HOODS 6"...
- Page 7 BACKSPLASH Optional stainless steel backsplashes are available in widths to match all pro wall hoods through your authorized Wolf dealer. For local dealer information, visit the find a showroom section of our website, wolfappliance.com.
- Page 8 " (83) x 10" (254) ductwork. An optional 3 " (83) x 10" (254) to 8" (203) CENTER OF round transition is available through your authorized Wolf TRANSITION dealer. For local dealer information, visit the find a showroom section of our website, wolfappliance.com.
- Page 9 Refer to the chart below. DUCT COVER INSTALLATION An optional horizontal discharge kit is available through your authorized Wolf dealer. For local dealer information, • Remove all screws from the front edge of the back visit the find a showroom section of our website, panel on the top of the wall hood.
-
Page 10: Pro Wall Hood Installation
Refer to installation instructions provided with the kit. Accessory kits are available through your authorized Wolf dealer. For IMPORTANT NOTE: Pro ventilation hoods must exhaust to local dealer information, visit the find a showroom section the outdoors except when used with the accessory recir- of our website, wolfappliance.com. - Page 11 Pro Wall Hood Installation wolfappliance.com/specs Install Ductwork LOW-PROFILE WALL HOODS 24" AND 27" DEEP WALL HOODS DUCTWORK INSTALLATION DUCTWORK INSTALLATION THROUGH ROOF THROUGH ROOF 18" (457) HEIGHT OF HOOD 10" (254) HEIGHT OF HOOD 22" 24" (559) (610) OR 27" DEPTH OF HOOD (686) 30"...
- Page 12 Pro Wall Hood Installation Low-Profile Wall Hoods WALL PREPARATION HOOD PREPARATION Construct the wall framing as shown in the illustration IMPORTANT NOTE: For low-profile wall hoods using the below. Be sure to locate horizontal framing using the 500 CFM internal blower, refer to installation instructions desired installation height of the hood.
- Page 13 Pro Wall Hood Installation wolfappliance.com/specs Low-Profile Wall Hoods HOOD INSTALLATION IMPORTANT NOTE: If a backsplash is to be used, it should be installed prior to mounting the wall hood. Refer to installation instructions provided with the backsplash. Install the wall mounting brackets as shown in the illustra- tions below.
- Page 14 Pro Wall Hood Installation 24" and 27" Deep Wall Hoods For ease of installation, the location of the wood mounting WALL PREPARATION support and retaining bracket allow for " (13) clearance Construct the wood wall framing flush with the wall studs at the top of the hood.
- Page 15 Pro Wall Hood Installation wolfappliance.com/specs 24" and 27" Deep Wall Hoods • Separate the transition from the back plate by HOOD PREPARATION removing the shipping nut from the inside of the back IMPORTANT NOTE: For 24" (610) and 27" (686) deep plate.
- Page 16 Pro Wall Hood Installation 24" and 27" Deep Wall Hoods REATTACH BACK PLATE HOOD INSTALLATION Attach the transition to the back plate using the four IMPORTANT NOTE: If a backsplash is to be used, it should shipping screws provided in the hardware mounting kit. be installed prior to mounting the wall hood.
- Page 17 Pro Wall Hood Installation wolfappliance.com/specs All Pro Wall Hoods WIRING CONNECTIONS FILTER INSTALLATION • Run a 120 V AC, 15 amp circuit power cable from the Slide the grease cups along the bottom edge of the hood service panel to the electrical box on the back plate. so that the lip of the grease cup overhangs slightly.
- Page 18 Pro Wall Hood Installation Wolf Nameplate Blower Assemblies The Wolf logo nameplate does not come installed on the Pro ventilation hoods are shipped without the blower hood since there are various locations that the nameplate assembly. Internal, in-line and remote blowers are avail- can be attached.
- Page 19 Pro Wall Hood Installation wolfappliance.com/specs Internal Blowers IMPORTANT NOTE: For low-profile wall hoods using the BLOWER INSTALLATION—24" AND 27" WALL HOODS 500 CFM internal blower, refer to installation instructions • Assemble the blower housing to the blower mounting provided with the blower assembly. Install the internal plate.
- Page 20 Refer to the illustrations below for overall dimensions of number of elbows and transitions are kept to a minimum. Wolf in-line and remote blowers. Installation instructions The duct run should be no longer than 50' (15 m). If shipped with each Wolf ventilation product provide possible, remote blowers should be located between wall detailed specifications.
- Page 21 Pro Wall Hood Installation wolfappliance.com/specs In-Line and Remote Blowers • Plug the cord assembly into the receptacle located BLOWER INSTALLATION near the center of the hood shell. Refer to the illustra- IMPORTANT NOTE: Refer to specific installation instruc- tion below. Use the clips on the interior of the hood to tions provided with each blower assembly for additional secure excess power cord.
-
Page 22: Service Information
• Verify that electrical power is being supplied to the ventilation hood. To obtain the name and number of a Wolf authorized service center, check the contact & support section of our • Check electrical connections to ensure that the website, wolfappliance.com or call Wolf customer service... - Page 23 The information and images in this guide are the copyright property of Wolf Appliance, Inc. Neither this guide nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Wolf Appliance, Inc. ©Wolf Appliance, Inc. all rights reserved.
- Page 24 WOLF APPLIANCE, INC. P. O. BOX 44848 MADISON, WI 53744 WOLFAPPLIANCE.COM 800.332.9513 811504 REV-B 4/ 2010...