Page 1
AOC LM-500 AOC LM-500 15 inch TFT LCD Monitor User’s Manual by Envision Peripherals, Inc. www.aocmonitor.com Before operating your monitor, please read this manual thoroughly. LM-500 v3_123102...
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. AOC LM-500 For Your Safety Notice 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Page 3
• Disconnect the power cord to stop the power supply to the monitor. AOC LM-500 For Your Safety • The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin.
EPI service center for replacement when the screen is dark, flickering or not lighting up. Never attempt to replace it by yourself. AOC LM-500 For Your Safety General Notes • Do not install the monitor near heat sources such as radiators or air ducts.
AOC LM-500 Package Contents The box that your monitor was shipped in should have included the following items: 1. LM-500 LCD Monitor 2. Power Cord 3. Windows 95/98/2000/ME/XP INF Driver Disk 4. Quick Start Guide 5. Booklet (Containing Warranty & Safety...
Page 6
3. Plug the other end of the power cord into a grounded AC outlet or UL-approved power strip. AOC LM-500 Caution: Make sure the power cord is the correct type that is required in your area. This LCD...
CEE-22 terminated connectors (see illustration above). AOC LM-500 Follow these steps: 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws.
• Hold the stand firmly when you change the monitor's angle. • You can adjust the monitor's angle from -5° to 45°. AOC LM-500 • Do not touch the LCD screen when you change the angle. It may cause damage or breakage.
Power Indicator: A green light indicates that the monitor is on. An orange light indicates that the monitor is in Off mode. AOC LM-500 Operating Instructions AOC LM-500 Power Button: Press this button to put the monitor into Off mode. The power indicator light will turn orange.
3. Press the Shuttle Knob again to open the function window. 4. Rotate the Shuttle Knob to change the settings of the function. AOC LM-500 Operating Instructions 5. To save and exit, highlight the EXIT icon and press Shuttle Knob or leave the monitor alone for 10 seconds.
EDID information. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B. AOC LM-500 Operating Instructions How to Install INF & ICM File 1. Insert the Windows 95/98/2000/ME/XP INF Driver Disk into your floppy drive.
• Confirm that your video card is Plug & Play compatible. • Inspect the video cable and make sure that none of the pins are bent. • Make sure the AOC monitor drivers are installed. (AOC monitor drivers are available at: www.aocmonitor.com) Picture is fuzzy •...
Page 13
• Make sure the video cable is properly connected to the computer. If the connector is loose, tighten the connector's two screws. • Inspect the video cable and make sure that none of the pins are bent. AOC LM-500 Technical Support (FAQ) Possible Solution...
640 x 480 640 x 400 640 x 350 720 x 400 640 x 480 640 x 480 640 x 480 800 x 600 AOC LM-500 Technical Support (FAQ) Possible Solution Vertical Frequency 60 Hz 800 x 600 70 Hz...
Response time Video Separate Sync. H-Frequency V-Frequency Display Colors Dot Clock Maximum Resolution AOC LM-500 Appendix Plug & Play TFT Color LCD Input Connector 15.0" (38.1 cm) Diagonal Input Video Signal (0.3 mm) (H) Maximum Screen Size (0.3 mm) (V) 100°...
Page 16
6500° K 7800° K RGB Color temp. Reset Exit EPA ENERGY STAR® Power Consumption 25 Watts (Maximum) Regulatory TCO92, UL, CSA, Compliance FCC, TÜV/GS, CE AOC LM-500 Appendix Optimal Viewing Mode: 1024 x 768 x 75 Hz AOC LM-500 v3_123102...