Advertisement
INSTRUCTION MANUAL
DW251-XE, DW252-XE, DW252WT-XE, DW255-XE, DW256-XE, DW257-XE, DW258-XE,
DW260-XE, DW262-XE, DW263-XE, DW265-XE, DW266-XE, DW266-220-XE, DW267-XE,
DW268-XE, DW268G -XE, DW268-220-XE, DW269-XE, DW272-XE, DW272W-XE,
DW272WT-XE, DW274-XE, DW274W-XE, DW274-220-XE, DW276-XE, DW276-220-XE,
DW281-XE, DW282-XE, DW284-XE
SCREWDRIVERS
Advertisement
Table of Contents
Related Manuals for DeWalt DW251-XE
Summary of Contents for DeWalt DW251-XE
- Page 1 INSTRUCTION MANUAL DW251-XE, DW252-XE, DW252WT-XE, DW255-XE, DW256-XE, DW257-XE, DW258-XE, DW260-XE, DW262-XE, DW263-XE, DW265-XE, DW266-XE, DW266-220-XE, DW267-XE, DW268-XE, DW268G -XE, DW268-220-XE, DW269-XE, DW272-XE, DW272W-XE, DW272WT-XE, DW274-XE, DW274W-XE, DW274-220-XE, DW276-XE, DW276-220-XE, DW281-XE, DW282-XE, DW284-XE SCREWDRIVERS...
-
Page 3: Definitions: Safety Guidelines
1. WORK AREA Definitions: Safety Guidelines a. Keep work area clean and well lit. Cluttered and dark areas invite accidents. b. Do not operate power tools in explosive atmospheres, such as in the The definitions below describe the level of severity for each presence of flammable liquids, gases or dust. -
Page 4: Extension Cords
d. Remove any adjusting key or wrench before turning the power tool on. A 5. SERVICE wrench or a key left attached to a rotating part of the power tool may result in a. Have your power tool serviced by a qualified repair person using only personal injury. -
Page 5: Additional Safety Instructions
Additional Safety Instructions WARNING: ALWAYS wear proper personal hearing protection that conforms to ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise • Hold tool by insulated gripping surfaces when performing an operation where from this product may contribute to hearing loss. the cutting tool may contact hidden wiring or its own cord. - Page 6 AND LOCATORS Depth Sensitive Units for Drill Point Screws Depth Sensitive Units 1. To change or install a new nutsetter: (DW251-XE, DW252-XE, DW255-XE, DW256-XE, DW257-XE, a. Pull forward on adjustment collar and remove DW258-XE, DW262-XE, DW265-XE, DW272-XE, DW274-XE, from clutch housing.
-
Page 7: Maintenance
2. Place nutsetter into clutch housing and push end of nutsetter until ball lock snaps 3. Test drive a fastener into a scrap piece to check proper fastener seating. It is into groove of nutsetter shank. normal after a period of use to require a slightly different collar setting due to wear on the clutch faces. - Page 8 FIG. 6 Recommended accessories for use with your tool are available at extra cost from Changing Clutches your local service center. If you need any assistance in locating any accessory, 1. Remove clutch housing by please contact D WALT Industrial Tool Co., 20 Fletcher Road, Mooroolbark, VIC 3138 unscrewing (left hand thread).
- Page 9 FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call (AUS) 1800 654 155 or (NZ) 09 259 1111 for a free replacement.
- Page 12 20 Fletcher Road, Mooroolbark, VIC 3138 Australia (03 8720 5100) • 5 Te Apunga Place, Mt Wellington, New Zealand (09 259 1111) (OCT07) Part No. 1007746-00 DW251-XE, etc. Copyright © 2007 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...