Toshiba TECRA A8 User Manual

Portable personal computer
Hide thumbs Also See for TECRA A8:
Table of Contents

Advertisement

TOSHIBA
TECRA A8 / Satellite Pro A120
Portable Personal Computer
User's Manual

Advertisement

Table of Contents
loading

Summary of Contents for Toshiba TECRA A8

  • Page 1 TOSHIBA TECRA A8 / Satellite Pro A120 Portable Personal Computer User’s Manual...
  • Page 2 This manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for the TOSHIBA TECRA A8 / Satellite Pro A120 Portable Personal Computer at the time of this manual’s production. However, succeeding computers and manuals are subject to change without notice.
  • Page 3: Fcc Information

    Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port, serial port, USB port,...
  • Page 4 EU Declaration of Conformity TOSHIBA declares, that the product: PTA82*/ PTA83*/ PSAC0*/ PSAC1* conforms to the following Standards: Supplementary “The product complies with the requirements of Information: the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/05/EEC.”...
  • Page 5 Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121. Germany ATAAB AN005,AN006,AN007,AN009,AN010 and DE03,04,05,08,09,12,14,17 Greece ATAAB AN005,AN006 and GR01,02,03,04 Portugal...
  • Page 6 One of the labels is located on the module. Pursuant to FCC CFR 47, Part 68: When you are ready to install or use the modem, call your local telephone company and give them the following information: ■ The telephone number of the line to which you will connect the modem ■...
  • Page 7: Type Of Service

    FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.
  • Page 8 Instructions for IC CS-03 certified equipment 1. The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
  • Page 9 Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia.
  • Page 10 ■ Some parameters required for compliance with Telecom’s PTC Specifications are dependent on the equipment (PC) associated with this modem. The associated equipment shall be set to operate within the following limits for compliance with Telecom Specifications: a/ There shall be no more than 10 call attempts to the same number within any 30 minute period for any single manual call initiation, and b/ The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the...
  • Page 11: General Conditions

    ■ The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired.
  • Page 12: Optical Disc Drive Safety Instructions

    Optical disc drive safety instructions Be sure to check the international precautions at the end of this section. Panasonic DVD-ROM&CD-R/RW UJDA770TB-A ■ The DVD-ROM&CD-R/RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference.
  • Page 13 DVD Super Multi with Double Layer Recording UJ-841BTJ-J ■ The DVD Super Multi drive with Double Layer Recording model employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
  • Page 14 TEAC CD-ROM CD-224E-NT4 ■ The CD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■...
  • Page 15 DVD-ROM DV-28E-RT4 ■ DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
  • Page 16 International precautions CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.”...
  • Page 17 OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
  • Page 18 xviii User’s Manual...
  • Page 19: Preface

    This manual tells how to set up and begin using your TECRA A8 / Satellite Pro A120 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
  • Page 20: Conventions

    Preface Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes and how to set a password. Chapter 7, Setup, explains how to configure the computer using the HW Setup program and TPM. Chapter 8, Optional Devices, describes the optional hardware available.
  • Page 21: Key Operation

    Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C.
  • Page 22 Preface xxii User’s Manual...
  • Page 23: General Precautions

    General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
  • Page 24: Heat Injury

    Heat injury ■ Avoid prolonged physical contact with the computer. If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time (if you rest the computer on your lap, or if you keep your hands on the palm rest, for example) your skin might suffer low-heat injury.
  • Page 25: Table Of Contents

    TECRA M5 Table of Contents Preface Manual contents ......... . xix Conventions.
  • Page 26 Operating Basics TOSHIBA Dual Pointing Device ......4-1 Using the Touch Pad ........4-1 Using the AccuPoint .
  • Page 27 DLA for TOSHIBA ........
  • Page 28 Using the Hard Disk Drive (HDD) Protection ....4-36 TOSHIBA HDD Protection Properties ..... . . 4-38 Details .
  • Page 29 Table of Contents TOSHIBA Password Utility ....... . . 6-12 User Password .
  • Page 30 TOSHIBA support ........
  • Page 31 Appendix B Display Controller and Modes Appendix C AT Commands Appendix D S-registers Appendix E V.90 Appendix F Wireless LAN Appendix G Bluetooth wireless technology Interoperability Appendix H AC Power Cord and Connectors Appendix I TOSHIBA Anti-theft Protection Timer Glossary Index User’s Manual xxxi...
  • Page 32 Table of Contents xxxii User’s Manual...
  • Page 33: Introduction

    Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
  • Page 34: Software

    ■ Fingerprint Utility ■ Online manual Documentation ■ TECRA A8 / Satellite Pro A120 Portable Personal Computer User's Manual ■ Microsoft Windows XP manual package Depending on the model, this manual is not included. ■ Instruction Manual for Safety & Comfort ■...
  • Page 35 Introduction Processor ■ Built-in The computer is equipped with one of the following Intel processors. ® ■ Intel Core Duo Processor, which ® incorporates a 2MB level 2 cache memory. It also supports Enhanced Intel ® SpeedStep ® Technology. ■ Intel Core Solo Processor, which...
  • Page 36 Introduction Legal Footnote (General Main Memory) For more information on the Legal Footnote regarding General Main Memory, please refer to the Legal Footnotes section in Chapter 10. Click the *2. Power Battery pack The computer is powered by one rechargeable lithium-ion battery pack.
  • Page 37: Optical Disk Drive

    Introduction USB floppy disk Accommodates either 3 1/2" 1.44-megabyte or drive 720-kilobyte floppy disk. It connects to a USB port. Optional or provide with some models. Optical disk drive Computers in this series can be configured with an optical disk drive installed.
  • Page 38 Introduction DVD-ROM&CD-R/RW Some models are equipped with a full-size, DVD- drive ROM&CD-R/RW drive module that lets you run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 24 speed and CD-RW at up to 24 speed.
  • Page 39: Toshiba Dual Pointing Device

    Refer to Chapter 5, Keyboard, for details. TOSHIBA Dual Pointing Device Built-in Touch Pad A Touch Pad and control buttons in the palm rest enable control of the on-screen pointer and scrolling of windows.
  • Page 40 Introduction Universal Serial Bus The computer has three Universal Serial Bus (USB 2.0) ports that comply with the USB 2.0 standard. Docking This port enables connection of an optional Advanced Port Replicator III Plus described in Options section. i.LINK™ (IEEE1394) This port enables high-speed data transfer directly from external devices such as digital video cameras.
  • Page 41 Introduction Communications Modem An internal modem provides capability for data and fax communication supporting the V.90 (V.92) standards. Refer to V.90 section in Appendix E. The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line.
  • Page 42 Introduction Wireless LAN Some computers in this series are equipped with a Wireless LAN card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard (Revision A, B or G). ■...
  • Page 43: Special Features

    Allows the connection of a security lock to anchor the computer to a desk or other large object. Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. TOSHIBA Assist...
  • Page 44 LCD display panel is opened. You can specify the setting in the When I close the lid item of the Setup Actions tab in TOSHIBA Power Saver. Low battery When battery power is exhausted to the point that...
  • Page 45: Utilities

    TOSHIBA Presentation button (default setting is the simultaneous display on LCD and CRT with resolution of 1,024 × 768) and to the TOSHIBA Assist button (default setting is the TOSHIBA Assist). To access this utility, click start, point to Control Panel, choose Printers and Other Hardware and click the Toshiba Controls icon.
  • Page 46 “shortcut” keys to quickly launch applications and speed your work in Windows. To start the utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Fn-esse. DVD Video Player The DVD Video Player is used to play DVD-Videos.
  • Page 47 Port Replicator III Plus. To access the utility, select TOSHIBA Mobile Extension from the TOSHIBA Assist application. TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to allow easy control of communication devices and network connections. TOSHIBA ConfigFree also allows you to find communication problems and create profiles for easy switching between locations and communication networks.
  • Page 48 Press Fn + Space keys to change the display resolution. TOSHIBA SD The TOSHIBA SD memory boot utility allows you Memory Boot Utility to create a bootable SD memory card to start the system. You can access TOSHIBA SD Memory Boot Utility from the menu bar as follows.
  • Page 49: Options

    ® models. Battery pack An battery pack (3600 mAh or 4400 mAh) can be additionally purchased from your TOSHIBA dealer. Use it as a spare or replacement. Universal If you use your computer at more than one site AC adaptor...
  • Page 50 Introduction 1-18 User’s Manual...
  • Page 51: The Grand Tour

    Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Legal Footnote (Non-applicable Icons) For more information on the Legal Footnote regarding Non-applicable Icons, please refer to the Legal Footnotes section in Chapter 10. Click the Front with the display closed Figure 2-1 shows the computer’s front with its LCD display panel in the closed position.
  • Page 52 The Grand Tour System indicators These LEDs let you monitor the status of various computer functions. Details are given in the System indicators section. Wireless Slide this switch to the left to turn off Wireless communication LAN and Bluetooth functions. Slide it to the right switch to turn on the functions.
  • Page 53: Left Side

    The Grand Tour Left side Figure 2-2 shows the computer’s left side. Cooling vents SD card slot PC card eject button PC card slot Figure 2-2 The left side of the computer Cooling vents Cooling vents help CPU keep from overheating. Do not block the cooling vents.
  • Page 54: Right Side

    The Grand Tour Right side Figure 2-3 shows the computer’s right side. Optical disk drive Security lock slot Figure 2-3 The right side of the computer Security lock slot A security cable attaches to this slot. The optional security cable anchors your computer to a desk or other large object to deter theft.
  • Page 55 The Grand Tour External monitor This external monitor port lets you connect an port external video display. DC IN 15V jack The AC adaptor connects to this jack. Use only the model of AC adaptor that comes with the computer. Using the wrong adaptor can damage your computer.
  • Page 56 The Grand Tour LAN active indicator This indicator glows orange when data is being (orange) exchanged between the computer and the LAN. i.LINK (IEEE1394) This port allows you to connect an external port device, such as a digital video camera for high- speed data transfer.
  • Page 57: Underside

    The Grand Tour Underside Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer. Notches Memory module cover Docking port Battery pack Battery Battery lock HDD pack cover screw release latch HDD pack cover Figure 2-5 The underside of the computer Battery lock...
  • Page 58 The Grand Tour ■ Only the Advanced Port Replicator III plus can be used with this computer. Do not attempt to use any other Port Replicator. ■ Keep foreign objects out of the docking port. A pin or similar object can damage the computer's circuitry.
  • Page 59: Front With The Display Open

    AccuPoint (Not shown) Touch Pad Stereo speaker Fingerprint (Left) Sensor Power button Touch Pad TOSHIBA Assist control buttons button Accupoint control button TOSHIBA Presentation button Figure 2-6 The front of the computer with the LCD display panel open User’s Manual...
  • Page 60: Accupoint Control

    The Grand Tour Display hinge The display hinge holds the LCD display panel at easy-to-view angles. Fingerprint sensor Fingerprint feature enables you to: ■ Logon to Windows and access a security- enabled homepage through IE (Internet Explorer). ■ Files and folders can be encrypted/decrypted and third party access to them prevented.
  • Page 61 When the computer is in Standby or Hibernation Mode or turned off, press this button to start the computer and launch the program. You can specify the function of TOSHIBA Assist button in the TOSHIBA Controls properties. Power button Press the power button to turn the computer’s power on and off.
  • Page 62: System Indicators

    The Grand Tour System indicators LEDs at the left side of the icons, light when various computer operations are in progress. Figure 2-7 System indicators SD card The SD card indicator glows green when the computer is accessing the SD card slot. DC IN The DC IN indicator glows green when DC power is supplied from the AC power adaptor.
  • Page 63: Keyboard Indicators

    The Grand Tour Keyboard indicators The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator. When the Arrow mode indicator glows the keypad overlay lets you control the cursor. When the Numeric mode indicator glows the keypad overlay lets you enter numbers.
  • Page 64: Usb Floppy Disk Drive

    The Grand Tour USB floppy disk drive The USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disk and connects to the USB port. It is supplied as standard with some models and as an option with others. USB connector Disk-In-Use Indicator Floppy disk...
  • Page 65: Optical Disk Drives

    The Grand Tour Optical disk drives One of the following Optical disk drives is installed in the computer: CD- ROM, DVD-ROM, DVD-ROM&CD-R/RW and DVD Super Multi drives. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows. For information on loading and unloading discs refer to the Using optical disk drives...
  • Page 66: Formats

    The Grand Tour Formats The drives support the following formats: ■ CD-ROM ■ DVD -Video ■ ■ DVD-ROM CD-Text ■ ■ CD-DA CD-ROM Mode 1, Mode 2 ■ Enhanced CD (CD-EXTRA) ■ Photo CD (single/multi-session) ■ Addressing Method 2 ■ CD-ROM XA Mode 2 (Form1, Form2) CD-ROM drive...
  • Page 67: Dvd Super Multi Drive

    The Grand Tour DVD Super Multi drive The full-size DVD Super Multi drive module lets you record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. ■ The read speed is slower at the center of a disc and faster at the outer edge.
  • Page 68 For use in other regions, please buy power cords that conform to safety rules and regulations in the particular region. Always use the TOSHIBA AC adaptor that was provided with your PC and the TOSHIBA Battery Charger (that may have been provided with your PC), or use AC adaptors and battery chargers specified by TOSHIBA to avoid any risk of fire or other damage to the PC.
  • Page 69: Getting Started

    Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Connecting the AC adaptor ■ Opening the display ■ Turning on the power ■ Starting up for the first time ■...
  • Page 70: Other Things To Note

    Power and Power-Up Modes. ■ Always use the Toshiba AC adaptor that was provided with your PC and the Toshiba Battery Charger (that may have been provided with your PC), or use Toshiba recommended alternate models to avoid any risk of fire or other damage to the PC. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the PC possibly resulting in serious injury.
  • Page 71 Getting Started ■ The supplied power cord conforms to safety rules and regulations in the region the product is bought and should not be used outside this region. For use in other regions, please buy power cords that conform to safety rules and regulations in the particular region. ■...
  • Page 72: Opening The Display

    Getting Started 2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the back of the computer. DC IN jack AC adaptor's DC output plug Figure 3-4 Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicators on the front of the computer should glow.
  • Page 73: Turning On The Power

    Getting Started Turning on the power This section describes how to turn on the power. The Power button LED indicates the status. Refer to the Power indicators section in Chapter 6, Power and Power-Up Modes. ■ After you turn on the power for the first time, do not turn it off until you have set up the operating system.
  • Page 74: Turning Off The Power

    ■ When the AC adaptor is connected, the computer will go into Standby Mode according to the settings in the TOSHIBA Power Saver utility. ■ To restore operation from Standby Mode, press the power button or press any key. The latter action only works on the internal keyboard if the Wake-up on Keyboard option is enabled in HW Setup.
  • Page 75 1. Click start, click Turn Off Computer and click Stand By. 2. Close the computer’s LCD display panel. This feature must be enabled. Refer to the Setup Actions tab in TOSHIBA Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver.
  • Page 76: Hibernation Mode

    For the computer to shut down in Hibernation Mode, this feature must be enabled in two places: the Hibernate tab in Power Options and Setup Actions tab in TOSHIBA Power Saver. If you do not configure this feature, the computer will shut down in Standby Mode - if battery power becomes depleted, data saved in Standby Mode will be lost.
  • Page 77: Automatic Hibernation

    3. Select the Hibernate window in the Power Options Properties, select the Enable hibernation check box and click the Apply button. 4. Open TOSHIBA Power Saver. 5. Select the Setup Action window. 6. Enable the desired Hibernation settings for When I press the power button and When I close the lid.
  • Page 78: Create Optical Recovery Discs

    Getting Started Create Optical Recovery Discs A recovery image of your computer is stored on the hard disk. You may use this image to create CD or DVD recovery discs using the following steps: 1. Select either blank CDs or DVD media. 2.
  • Page 79 2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key. 3. Use the left or right cursor key to select the CD-ROM icon in the display menu.
  • Page 80 Getting Started 3-12 User’s Manual...
  • Page 81: Operating Basics

    This chapter describes the basic operations of your computer and precautions when using it, as well as the handling of CD/DVD. TOSHIBA Dual Pointing Device The computer is equipped with a dual point system: a Touch Pad and an AccuPoint pointing stick.
  • Page 82: Using The Accupoint

    Operating Basics You can also tap the Touch Pad to perform functions similar to those of the left button. Click: Tap once Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material.
  • Page 83: Using The Fingerprint Sensor

    Operating Basics 2. Position a new cap on the peg and press it into place. The peg is square, so be careful to align the cap’s square hole with the peg. Using the Fingerprint Sensor This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints.
  • Page 84 Operating Basics ■ Clean the sensor with a lint-free cloth. Do not use detergent to clean the sensor. ■ Avoid the following finger conditions for enrollment or recognition as they may result in fingerprint enrollment errors or a drop in the fingerprint recognition success rate ■...
  • Page 85: Points To Note About The Fingerprint Utility

    Toshiba does not guarantee that the fingerprint sensor will recognize the enrolled user or accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of this fingerprint recognition software or utility.
  • Page 86: Set Up Procedure

    Operating Basics Set Up Procedure Please use the following procedure when first using fingerprint authentication. Fingerprint Registration Enroll the required authentication data using the "User Enrollment" Wizard. ■ The fingerprint authentication uses the same Windows logon ID and password. If the Windows logon password has not been setup, please do so before registration.
  • Page 87: Fingerprint Power-On Security

    ■ It is necessary to register the User Password before using the Fingerprint Power-on Security and its extended function, the Fingerprint Single Sign-on Feature. Please use TOSHIBA Password Utility to register the User Password. ■ If you fail fingerprint authentication more than five times, you must enter the User Password or Supervisor Password manually to start the computer.
  • Page 88: Fingerprint Single Sign-On Feature

    Password and Windows Logon password before using the Fingerprint Power-on Security and this Fingerprint Single Sign-on Feature. Please use TOSHIBA Password Utility to register your User/BIOS Password. If Windows Logon is not the default for your system, see Manual to register your Windows Logon password.
  • Page 89: Fingerprint Utility Limitations

    TOSHIBA does not guarantee that the Fingerprint utility will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software or utility.
  • Page 90: Using The Usb Floppy Disk Drive

    Operating Basics Using the USB floppy disk drive The USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disk and connects to the USB port. Refer to Chapter 2, The Grand Tour, for more information. It is supplied as standard with some models and as an option with others.
  • Page 91: Using Optical Disk Drives

    Operating Basics Using optical disk drives The text and illustrations in this section refer primarily to the optical disk drive.The full-size drive provides high-performance execution of CD/DVD- ROM-based programs. You can run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without an adaptor.
  • Page 92 Operating Basics 3. Lay the CD/DVD, label side up, in the disc tray. Laser lens Figure 4-6 Inserting a CD/DVD When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the disc tray.
  • Page 93: Removing Discs

    Operating Basics 5. Push the center of the disc tray to close it. Press gently until it locks into place. If the CD/DVD is not seated properly when the disc tray is closed, the CD/ DVD might be damaged. Also, the disc tray might not open fully when you press the eject button.
  • Page 94: How To Remove Cd/Dvd When The Disc Tray Will Not Open

    Operating Basics 3. Push the center of the disc tray to close it. Press gently until it locks into place. How to remove CD/DVD when the disc tray will not open Pressing the eject button will not open the disc tray when the computer power is off.
  • Page 95: Before Writing Or Rewriting

    RICOH Co., Ltd. Ultra-Speed CD-RW: MITSUBISHI CHEMICAL CORPORATION TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. ■ The actual number of rewrites to CD-RW is affected by the quality of the disc and the way it is used.
  • Page 96: When Writing Or Rewriting

    Operating Basics When writing or rewriting Note the following when you write or rewrite a CD-R or CD-RW. ■ Always copy data from the hard disk drive to the optical media. Do not use cut-and-paste as the original data will be lost if there is a write error. ■...
  • Page 97: Important Message

    Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW or DVD-R/-R DL/-RW/+R/+R DL/ +RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.
  • Page 98 Operating Basics DVD-R: DVD Specifications for Recordable Disc for General Version 2.0 TAIYO YUDEN CO., LTD. Matsushita Electric Industrial Co., Ltd. DVD-R DL: MITSUBISHI CHEMICAL CORPORATION. DVD+R: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD+R DL: MITSUBISHI CHEMICAL CORPORATION DVD-RW: DVD Specifications for Recordable Disc for Version 1.1 or version VICTOR COMPANY OF JAPAN.LIMITED MITSUBISHI CHEMICAL CORPORATION DVD+RW:...
  • Page 99 Operating Basics ■ You can use DVD-RAM discs that can be removed from a cartridge and DVD-RAM discs designed without a cartridge. ■ Other DVD-ROM drives for computers or other DVD players may not be able to read DVD-R/-R DL/-RW or DVD+R/+R DL/+RW discs. ■...
  • Page 100: When Writing Or Rewriting

    The original data will be lost if there is a write error. DISC created in DVD-R DL format4 (Layer Jump Recording) cannot be read. RecordNow! Basic for TOSHIBA Note the following limitations when you use RecordNow!: ■ DVD-Video cannot be created using RecordNow!.
  • Page 101: Data Verification

    Operating Basics ■ You cannot back up DVD-ROM, DVD-Video, DVD-R/-R DL/-RW or DVD+R/+R DL/+RW to CD-R/RW using the “Exact Copy” function of RecordNow!. ■ RecordNow! cannot record in packet format. ■ You might not be able to use the “Exact Copy” function of RecordNow! to back up a DVD-R/-R DL/-RW or DVD+R/+R DL/+RW disc that was made with other software on a different DVD-R/-R DL/-RW or DVD+R/ +R DL/+RW recorder.
  • Page 102: Dla For Toshiba

    Operating Basics DLA for TOSHIBA Note the following limitations when you use DLA: ■ This software supports only rewritable discs (DVD+RW, DVD-RW, and CD-RW). It does not support DVD+R/+R DL, DVD-R/-R DL, and CD-R discs that are not rewritable. ■...
  • Page 103: How To Make A Dvd-Video

    Operating Basics How to make a DVD-Video Simplified steps for making a DVD-Video from video data captured from a DV-Camcorder: 1. Click Start -> All Programs -> InterVideo WinDVD Creator2 -> InterVideo WinDVD Creator to launch WinDVD Creator. 2. Click Capture button then capture the video data from the DV- Camcorder via IEEE1394.
  • Page 104 2. Before recording the video to DVD ■ When you record to DVD discs, please use only media recommended by TOSHIBA. ■ Do not set the working drive to a slow device like a USB 1.1 hard disk drive or it will fail to write the DVD.
  • Page 105: Media Care

    Operating Basics ■ If you use an over-used rewritable disc, the full formatting might be locked. Please use a brand new disc. Media care This section provides tips on protecting data stored on your CD/DVDs and floppy disks. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1.
  • Page 106: Sound System

    Operating Basics 7. Do not place heavy objects on your floppy disks. 8. Do not eat, smoke, or use erasers near your floppy disks. Foreign particles inside the floppy disk’s jacket can damage the magnetic surface. 9. Magnetic energy can destroy the data on your floppy disks. Keep your floppy disks away from speakers, radios, television sets and other sources of magnetic fields.
  • Page 107: Modem

    Check the specified areas carefully before using it. To select a region, follow the steps below. 1. Click start, point to All Programs, point to TOSHIBA, point to Networking and click Modem Region Select. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.
  • Page 108: Properties Menu

    Operating Basics Properties menu Click the icon with the secondary mouse button to display properties menu on the screen. Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system.
  • Page 109 Operating Basics ■ Connection to any communication line other than an analog phone line could cause a PC system failure. ■ Connect the built-in modem only to ordinary analog phone lines. ■ Never connect the built-in modem to a digital line (ISDN). ■...
  • Page 110: Disconnecting

    Operating Basics Disconnecting To disconnect the internal modular cable, follow the steps below. 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2. Disconnect the cable from the computer’s modem jack in the same manner.
  • Page 111: Security

    ■ TOSHIBA is not liable for the loss of data due to eavesdropping or illegal access through the Wireless LAN and the damage thereof. Bluetooth wireless technology Some models in this series are equipped with Bluetooth™...
  • Page 112: Bluetoothtm Stack For Windows® By Toshiba

    This Bluetooth Stack is based on Bluetooth Version 1.1/1.2/2.0+EDR specification. TOSHIBA cannot confirm compatibility between any PC products and/or other electronic devices that use Bluetooth other than TOSHIBA mobile PCs. Release Notes related to the Bluetooth Stack for ®...
  • Page 113: Wireless Communication Switch

    Operating Basics Wireless communication switch You can enable or disable Wireless LAN and Bluetooth functions, with the on/off switch. No transmissions are sent or received when the switch is off. Slide the switch to the right to turn it on and to the left to turn it off. ■...
  • Page 114: Lan

    Operating Basics The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T (only for Intel ® Core Duo/Solo Processor models)). This section describes how to connect/disconnect to a LAN.
  • Page 115: Disconnecting Lan Cable

    Operating Basics 2. Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place. LAN connector LAN jack Figure 4-11 Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub.
  • Page 116: Moving The Computer

    Operating Basics Moving the computer The computer is designed for rugged durability. However, a few simple precautions taken when moving the computer will help ensure trouble-free operation. ■ Before moving the computer, it recommends changing the function of HDD Protection. Refer to the section, Using the Hard Disk Drive (HDD) Protection, in this chapter.
  • Page 117: Taskbar Icon

    Operating Basics When vibration is detected, the following message is displayed, and the icon in the notification area of the taskbar is changed to the protection state. This message is displayed until the OK button is pressed or 30 seconds pass. When vibration subsides, the icon returns to the normal state.
  • Page 118: Toshiba Hdd Protection Properties

    Operating Basics TOSHIBA HDD Protection Properties You can make the HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click start, point to All Programs, point to TOSHIBA, point to Utilities and click HDD Protection setting.
  • Page 119: Details

    Operating Basics Details To open the Details window, click the Setup Detail button in the TOSHIBA HDD Protection Properties window. Figure 4-14 Details Detection Level Amplification When the AC adaptor is disconnected or the lid is closed, HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds.
  • Page 120: Heat Dispersal

    CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver. When the CPU temperature falls to a normal range, the fan is turned off and the CPU operation returns to standard speed.
  • Page 121: The Keyboard

    Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/ 102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with.
  • Page 122: Function Keys: F1

    Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
  • Page 123: Hot Keys

    The Keyboard Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to Keypad overlay section in this chapter for more information on how to operate these keys.
  • Page 124 F2 again to toggle between the settings. Release both Fn and F2 to put the new setting into effect. You can also change this setting through the Profile options in TOSHIBA Power Saver. Standby: When you press Fn + F3, the computer enters the Standby Mode.
  • Page 125 You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver. ■ The brightness level is always set at the maximum value for about 18 seconds, when the internal LCD screen turns on.
  • Page 126: Fn Sticky Key

    Fn key. Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an “F number” key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Accessibility.
  • Page 127: Windows Special Keys

    The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows: Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button.
  • Page 128: Numeric Mode

    The Keyboard Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys in figure 5-2. Press Fn + F11 again to turn off the overlay. Figure 5-2 The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard...
  • Page 129: Temporarily Changing Modes

    The Keyboard Temporarily changing modes If the computer is in Numeric mode, you can switch temporarily to Arrow mode by pressing a shift key. If the computer is in Arrow mode, you can switch temporarily to Numeric mode by pressing a shift key. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation.
  • Page 130 The Keyboard 5-10 User’s Manual...
  • Page 131: Power And Power-Up Modes

    Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. Power conditions The computer’s operating capability and battery charge status are affected by the power conditions: whether an AC adaptor is connected, whether a...
  • Page 132: Power Indicators

    DC IN off For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window. If a main battery and a 2nd battery are installed, the computer does not shut down until the charge in both batteries is exhausted.
  • Page 133: Dc In Indicator

    Power and Power-Up Modes Indicates the AC adaptor is connected and the Green battery is fully charged. Under any other conditions, the indicator does No light not light. If the battery pack becomes too hot while it is being charged, the charge will stop and the Battery indicator will go out.
  • Page 134: Battery Pack

    The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ Always use the battery pack supplied as an accessory or an equivalent battery pack specified in the User's Manual.
  • Page 135: Real Time Clock (Rtc) Battery

    The computer’s RTC battery is a Ni-MH battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations.
  • Page 136: Charging The Batteries

    The Battery indicator glows orange when the battery is being charged. Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger.
  • Page 137: Battery Charging Notice

    Power and Power-Up Modes Time The following table shows the approximate time required to fully charge a discharged battery. Charging time (hours) Battery type Power on Power off Battery pack (3600 mAh) about 4.5 to 10.0 or longer about 3.0 Battery pack (4400 mAh) about 5.5 to 12.0 or longer about 3.0 RTC battery...
  • Page 138: Monitoring Battery Capacity

    Therefore, an often used, older battery will not operate for as long as a new battery even when both are fully charged. In this case, TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery.
  • Page 139: Retaining Data With Power Off

    Power and Power-Up Modes ■ The condition of the battery terminals. Make sure the battery terminals stay clean by wiping them with a clean dry cloth before installing the battery pack. Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Retention time Battery type...
  • Page 140: Extending Battery Life

    Power and Power-Up Modes Extending battery life To extend the life of your battery pack: ■ At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below.
  • Page 141 Power and Power-Up Modes ■ Do not remove the battery pack while the computer is in Standby Mode. Data is stored in RAM, so if the computer loses power it will be lost. ■ In Hibernation Mode, data will be lost if you remove the battery pack or disconnect the AC adaptor before the save is completed.
  • Page 142: Toshiba Password Utility

    ( 12. Turn your computer over. TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows password.
  • Page 143: User Password

    Power and Power-Up Modes User Password To start the utility, point to or click the following items: start -> All Programs -> TOSHIBA -> Utilities ->Password Utility The User Password dialog box contains two main fields: User Password and User Token.
  • Page 144 ■ If you forget your HDD User Password, TOSHIBA will NOT be able to assist you, and your HDD will be rendered COMPLETELY and PERMANENTLY INOPERABLE. TOSHIBA will NOT be held...
  • Page 145: Supervisor Password

    Register, delete or change the Supervisor Password. ■ Create or invalidate a Supervisor Password token. This function in the TOSHIBA Password Utility lets you invalidate only supervisor tokens or all tokens, including user and supervisor tokens. ■ Specify restrictions for general users.
  • Page 146: Power-Up Modes

    Chapter 3, Getting Started. Windows utilities You can configure various settings associated with both Standby Mode and Hibernation Mode within TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Standby Mode and Fn + F4 to enter Hibernation.
  • Page 147: Hw Setup

    Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer, and provides information on setting up the Execute-Disable Bit Capability and TPM. Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HWSetup.
  • Page 148: Power On Display

    HW Setup General This window displays the BIOS version and contains two buttons: Default and About. Return all HW Setup values to the factory Default settings. Display the HW Setup version. About Setup This field displays BIOS Version and date. Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor.
  • Page 149: Boot Priority

    HW Setup Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select from the following settings: HDD −> FDD −> CD- The computer looks for bootable files in the ROM −> LAN following order: HDD, floppy disk drive* , CD- ROM* and LAN (Default).
  • Page 150 HW Setup To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in HDD, CD-ROM, FDD (or SD memory card), Network (LAN), USB Memory boot.
  • Page 151 HW Setup HDD Priority Options If more than one HDD is installed in the computer, this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD. The priority is set as built-in HDD ->...
  • Page 152 HW Setup Keyboard External Keyboard Fn key Use this option to set a key combination on an external keyboard to emulate the Fn key on the computer’s internal keyboard. Setting an Fn key equivalent will let you use Hot keys by pressing the set combination instead of the Fn key (PS/2 keyboard only).
  • Page 153 HW Setup This function lets you set the CPU operating mode. This option is displayed only on models with an Intel ® Core processor and Intel ® Core Solo processor. Dynamic CPU Frequency Mode This option lets you choose from the following settings: CPU power consumption and clock speed Dynamically automatic switching function is enabled.
  • Page 154: Device Config

    HW Setup Device Config Device Configuration This option lets you set the device configuration. BIOS sets all devices. All Devices Operating system sets devices that it can control Setup by OS (Default). Parallel/Printer Some models are equipped with Parallel/Printer tab. This tab lets you set the Parallel Port Mode.
  • Page 155: Configuring The Execute-Disable Bit Capability And Tpm

    ■ In most cases, changes to the system's configuration should be made within Windows by using applications such as TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Windows Device Manager and so forth. If you make changes to the...
  • Page 156: Ending The Bios Setup Program

    HW Setup Ending the BIOS Setup Program Save the changes and end the program. 1. Press the End Key. The “Are you sure? (Y/N) The changes you made will cause the system to reboot.” message is displayed. 2. Press the Y key. The configured settings are saved and the BIOS setup program ends.
  • Page 157: Security Controller

    Capability so that it is not available for use. (Default). System configuration changes, other than changes to this setting, should be made within Windows by using applications such as TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Windows Device Manager and so forth.
  • Page 158: Diagnostic Mode

    ■ System configuration changes other than changes to this setting should be made in Windows using TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Device Manager, etc. ■ When using TPM, please install the Infineon TPM Installation Guide from the TOSHIBA Application Installer.
  • Page 159: Optional Devices

    Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory ■ PC card ■ SD card ■ Memory expansion Power devices ■...
  • Page 160: Pc Card

    The computer is equipped with a PC card slot that can accommodate a Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.
  • Page 161: Removing A Pc Card

    Optional Devices Removing a PC card To remove the PC card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to PC card and click. 3. Press the PC card eject button to extend it. If the PC card is not inserted all the way, the eject button may not cause it to pop out sufficiently to allows it to be grasped.
  • Page 162: Formatting An Sd Memory Card

    TOSHIBA SD memory card format utility, not with the format commands provided within Windows. In order to run TOSHIBA SD memory card format, click start, point to All Programs, point to TOSHIBA, point to Utilities and click SD memory card Format.
  • Page 163: Sd Card Care

    Do not touch the metal part or expose it to liquids or let it get dirty. Creation of a boot disk Within the TOSHIBA SD Memory Boot Utility, a bootable SD memory card can be created if required. Refer to the...
  • Page 164: Memory Expansion

    When you install or remove a memory module, ensure that you do not touch any other internal areas of the computer. ■ Use only memory modules approved by TOSHIBA. ■ Do not try to install or remove a memory module under the following...
  • Page 165: Installing A Memory Module

    Optional Devices Installing a memory module There are slots for two memory modules, one over the other. The procedures are the same for installing either module. 1. Set the computer to boot mode and turn the computer’s power off. Make sure the Power indicator is off. Refer to the Turning off the power section in Chapter 3, Getting Started.
  • Page 166: Removing A Memory Module

    Optional Devices Align the grooves along the edges of the memory module with the locking tabs on the connector and insert the module into the connector firmly. If you find it difficult to install the memory module, gently prize the locking tabs outwards using the tip of your finger.
  • Page 167: Battery Pack

    Optional Devices 3. Turn the computer upside down and remove the battery pack. Refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, for details. 4. Loosen the screw securing the memory module cover. The screw is attached to the cover to prevent it from being lost.
  • Page 168: Ac Adaptor

    Optional Devices AC adaptor If you frequently transport the computer between different sites such as your home and office, purchasing an AC adaptor for each location will reduce the weight and bulk of your carrying load. Battery charger The battery charger provides a convenient way to charge battery packs without requiring the use of your computer.
  • Page 169: Using The Toshiba Assist Button Or Toshiba Presentation Button8-11

    2. Connect the TV adaptor cable’s S-Video plug to the Video-out jack on the TV. 3. Press the TOSHIBA Assist button or TOSHIBA Presentation button. You can use the hot keys Fn + F5 to change the display device. Refer to Chapter 5, Keyboard.
  • Page 170: Changing The Resolution

    Optional Devices If a television is connected to the computer (Intel ® Core Duo/Solo Processor model), set the TV type in Display Properties. Follow the steps below. a. Click start and click Control Panel. b. Double-click the Display icon to open the Display Properties window.
  • Page 171: I.link (Ieee1394)

    There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. ■ Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise.
  • Page 172: Connecting

    Optional Devices Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. i.LINK (IEEE1394) port i.LINK (IEEE1394) connector Figure 8-17 Connecting the i.LINK (IEEE1394) cable into the computer 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ■...
  • Page 173: Advanced Port Replicator Iii Plus

    Optional Devices Advanced Port Replicator III Plus In addition to the ports available on the computer, the Advanced Port Replicator III Plus provides serial port and separate ports for PS/2 mouse and PS/2 keyboard. The Advanced Port Replicator III Plus connects directly to the docking interface on the underside of the computer.
  • Page 174: Serial Port

    Optional Devices The following ports and accessories are available on the Advanced Port Replicator III Plus. ■ RJ45 LAN jack ■ RJ11 Modem jack ■ External monitor port ■ Parallel port ■ Serial port ■ PS/2 mouse port ■ PS/2 keyboard port ■...
  • Page 175: Security Lock

    Optional Devices Security lock Security locks enable you to anchor your computer and optional Advanced Port Replicator III Plus to a desk or other heavy object to help prevent unauthorized removal of the computer or Advanced Port Replicator III Plus. The computer has a security lock slot on the left side.
  • Page 176 Optional Devices 8-18 User’s Manual...
  • Page 177: Troubleshooting

    Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.
  • Page 178: Preliminary Checklist

    Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer.
  • Page 179: Hardware And System Checklist

    Before using a peripheral device or application software that is not an authorized Toshiba part or product, make sure the device or software can be used with your PC. Use of incompatible devices may cause injury or may damage your PC.
  • Page 180: Self Test

    This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: ■...
  • Page 181 Troubleshooting If the computer has reached room temperature and still does not start, or if it starts but shuts down quickly contact your dealer. Computer shuts down Indicates a problem with the heat dispersal and its DC IN indicator system. Please contact your dealer. is flashing green AC power If you have trouble turning on the computer with the AC adaptor connected,...
  • Page 182 Fully discharge the battery, then try to charge it again. Check the power consumption settings in TOSHIBA Power Saver utility. Consider using a power saving mode. User’s Manual...
  • Page 183: Password

    Password Problem Procedure Cannot enter Refer to the TOSHIBA Password Utility section in password Chapter 6, Power and Power-Up Modes. Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, Keyboard.
  • Page 184: Internal Lcd Display Panel

    Troubleshooting Internal LCD display panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, Setup, for more information. Problem Procedure No display Press hotkeys Fn + F5 to change the display priority, to make sure it is not set for an external monitor.
  • Page 185: Cd-Rom Drive

    Troubleshooting CD-ROM drive Problem Procedure You cannot access a Make sure the drive’s disc tray is securely CD in the drive closed. Press gently until it clicks into place. Check whether the drive power is on. If the power is off, click on the optical disk drive icon in the task tray and turn on the power.
  • Page 186: Dvd-Rom Drive

    Troubleshooting DVD-ROM drive Problem Procedure You cannot access a Make sure the drive’s disc tray is securely CD/DVD in the drive closed. Press gently until it clicks into place. Check whether the drive power is on. If the power is off, click on the optical disk drive icon in the task tray and turn on the power.
  • Page 187: Dvd-Rom&Cd-R/Rw Drive

    Troubleshooting DVD-ROM&CD-R/RW drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a Make sure the drive’s disc tray is securely CD/DVD in the drive closed. Press gently until it clicks into place. Check whether the drive power is on. If the power is off, click on the optical disk drive icon in the task tray and turn on the power.
  • Page 188: Dvd Super Multi Drive

    Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording.
  • Page 189: Usb Floppy Disk Drive

    Troubleshooting Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: CD-DA, CD-Text, Photo CD (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), Addressing Method 2 Check the region code on the DVD. It must match that on the DVD Super Multi drive.
  • Page 190: Pc Card

    Device tab. Then click the Detail Setting button and click the Device Select tab. Check that the Touch Pad is not selected. Pressing Fn + F9 to enables TOSHIBA Dual Pointing Device. On-screen pointer The system might be busy. If the pointer is...
  • Page 191: Usb Mouse

    Troubleshooting Problem Procedure Double-tapping Try changing the double-click speed setting in (Touch Pad) or the mouse control utility. double-clicking 1. Click start, click Control Panel, click (AccuPoint) does not Printers and Other Hardware and select work Mouse icon. 2. Click the Buttons tab. 3.
  • Page 192: Fingerprint Sensor

    Troubleshooting Fingerprint Sensor Problem Procedure Reading of the Try again using the correct posture. Align your fingerprint was not fingertip with the sensor as shown in the drawing successful. and Swipe. Refer to Using the Fingerprint Sensor in Chapter 4, Operating Basics.Try the recognition process again using another enrolled finger.
  • Page 193: Memory Expansion

    Troubleshooting Memory expansion Refer also to Chapter 8, Optional Devices, for information on installing memory modules. Problem Procedure If there is a memory Make sure the memory module installed in the malfunction, the power memory slot is compatible with the computer. LED flashes (on for If an incompatible module has been installed, 0.5 seconds, off for...
  • Page 194: External Monitor

    Troubleshooting External monitor Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation. Problem Procedure Monitor does not turn Make sure that the external monitor’s power switch is on. Confirm that the external monitor’s power cable is plugged into a working power outlet.
  • Page 195: Modem

    Troubleshooting Modem Refer to Appendix C, AT Commands and Appendix D, S-registers. Problem Procedure Communication Make sure the computer’s internal modem software can’t initialize settings are correct. Refer to Phone and Modem modem Properties in the Control Panel. You can hear a dial If the call is going through a PBX machine, make tone but can’t make a sure the communication application’s tone dial...
  • Page 196: Lan

    Troubleshooting Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN hub. Wake-up on LAN does Make sure the AC adaptor is connected. The not work Wake-up on LAN function consumes power even when the system is off.
  • Page 197: Printer

    Troubleshooting Printer Refer also to the Serial port sections in Chapter 8, Optional Devices, and to the troubleshooting and other relevant sections in your printer and software documentation. An Advanced Port Replicator III Plus is equipped with a parallel port. Problem Procedure Printer does not turn on.
  • Page 198: Recovery Discs

    "Restore Original Factory Image" from the drop-down menu. If you have not created "Recovery Media", please contact TOSHIBA support for assistance. Disposing of PC and PC batteries ■ Discard this PC in accordance with applicable laws and regulations. For further information, contact your local government.
  • Page 199: Toshiba Support

    All data deletion costs will be borne by you. TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.
  • Page 200 Troubleshooting Outside of Europe In Europe Singapore Spain TOSHIBA Singapore Pte. Ltd. TOSHIBA Information Systems, ESPAÑA 438B Alexandra Road #06-01 Parque Empresarial San Fernando Alexandra Technopark Edificio Europa, l Planta, Singapore 119968 Escalera A 28830 Madrid United States of America...
  • Page 201: Legal Footnotes

    Chapter 10 Legal Footnotes This chapter states the Legal Footnote information applicable to TOSHIBA computers. In the text in this manual, *XX is used to show which Legal Footnote description is related to TOSHIBA computers. Description(s) related to this computer are marked with a blue *XX in this manual.
  • Page 202: General Main Memory*2

    Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
  • Page 203: Lcd*5

    Legal Footnotes Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology. Maximum brightness is only available when operating in AC power mode. The screen will dim when the computer is operated on battery power and not be able to increase the brightness of the screen.
  • Page 204 Legal Footnotes 10-4 User’s Manual...
  • Page 205: Appendix A Specifications

    Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Weight (typical) Maximum 2.98 kilograms, configured with: 15.4" WXGA, 1,024MB+1.024MB RAM, 100GB HDD, DVD-Super Multi drive, Wireless LAN, Bluetooth. Minimum 2.85 kilograms, configured with: 15.4" WXGA, 256MB+0MB RAM, 40GB HDD, CD-ROM drive.
  • Page 206: Power Requirements

    Specifications Conditions Altitude (from sea level) Operating -60 to 3,000 meters Non-operating -60 to 10,000 meters maximum Power Requirements AC adaptor 100-240 volts AC 50 or 60 hertz (cycles per second) Computer 15 VDC 4.0 amperes Built-in Modem Network control unit (NCU) Type of NCU Type of line Telephone line (analog only)
  • Page 207 Specifications Network control unit (NCU) Communication Data protocol ITU-T-Rec V.21/V.22/V.22bis/V.32 (Former CCITT) /V.32bis/V.34/V.90 Bell 103/212A ITU-T-Rec V.17/V.29/V.27ter (Former CCITT) /V.21 ch2 Communication Data transmission and reception speed 300/1200/2400/4800/7200/9600/12000/14400/ 16800/19200/21600/24000/26400/28800/31200/ 33600 bps Data reception only with V.90 28000/29333/30666/32000/33333/34666/36000/ 37333/38666/40000/41333/42666/44000/45333/ 46666/48000/49333/50666/52000/53333/54666/ 56000 bps 2400/4800/7200/9600/12000/14400 bps Transmitting level -10 dBm...
  • Page 208 Specifications User’s Manual...
  • Page 209: Appendix B Display Controller And Modes

    Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular parts on the screen on or off. ■ 15.4" WXGA, 1280 horizontal × 800 vertical pixels Because of the LCD’s increased resolution, lines may appear broken in DOS mode.
  • Page 210 Display Controller and Modes Table1 Video modes (VGA) Video mode Type Resolution Character Colors Scanning matrix frequency (pels) Vertical (Hz) 0, 1 40 × 25 8 × 8 16 of 256K Text Characters 2, 3 80 × 25 8 × 8 16 of 256K Text Characters...
  • Page 211 Display Controller and Modes Table1 Video modes (VGA) continued Video Type Resolution Character Colors Scanning mode matrix frequency (pels) Vertical (Hz) 320 × 200 8 × 8 16 of 256K Grph Pels 640 × 200 8 × 8 16 of 256K Grph Pels 640 ×...
  • Page 212 Display Controller and Modes ® ® Table 2 Video modes (WXGA, Intel Celeron M Processor model) Resolution Vertical colors colors frequency (Hz)* 640 × 480 256/256K 256/256K 800 × 600 256/256K 256/256K 1024 × 768 256/256K 256/256K 1280 × 800 256/256K 256/256K 1280 ×...
  • Page 213 Display Controller and Modes ® ® Table 2 Video modes (WXGA, Intel Celeron M Processor model) continued Resolution Vertical colors colors frequency (Hz)* 640 × 480 64K/64K 64K/64K 800 × 600 64K/64K 64K/64K 1024 × 768 64K/64K 64K/64K 1280 × 800 64K/64K 64K/64K 1280 ×...
  • Page 214 Display Controller and Modes ® ® Table 2 Video modes (WXGA, Intel Celeron M Processor model) continued Resolution Vertical colors colors frequency (Hz)* 640 × 480 16M/16M 16M/16M 800 × 600 16M/16M 16M/16M 1024 × 768 16M/16M 16M/16M 1280 × 800 16M/16M 16M/16M 1280 ×...
  • Page 215 Display Controller and Modes ® Table 3 Video modes (WXGA, Intel Core Duo/Solo Processor model) Resolution Vertical colors colors frequency (Hz)* 640 × 480 256/256K 256/256K 800 × 600 256/256K 256/256K 1024 × 768 256/256K 256/256K 1280 × 800 256/256K 256/256K 1280 ×...
  • Page 216 Display Controller and Modes ® Table 3 Video modes (WXGA, Intel Core Duo/Solo Processor model) continued Resolution Vertical colors colors frequency (Hz)* 640 × 480 64K/64K 64K/64K 800 × 600 64K/64K 64K/64K 1024 × 768 64K/64K 64K/64K 1280 × 800 64K/64K 64K/64K 1280 ×...
  • Page 217 Display Controller and Modes ® Table 3 Video modes (WXGA, Intel Core Duo/Solo Processor model) continued Resolution Vertical colors colors frequency (Hz)* 640 × 480 16M/16M 16M/16M 800 × 600 16M/16M 16M/16M 1024 × 768 16M/16M 16M/16M 1280 × 800 16M/16M 16M/16M 1280 ×...
  • Page 218 Display Controller and Modes B-10 User’s Manual...
  • Page 219: Appendix C At Commands

    Appendix C AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software.
  • Page 220 AT Commands Answer command This command instructs the modem to go off-hook and answer an incoming call. Communication standard setting This command determines the communication standard CCITT or Bell. Selects CCITT V.22 mode when the modem is at 1200 bps. Selects Bell 212A when the modem is at 1200 bps (default).
  • Page 221 AT Commands Disables echo to the computer. Enables echo to the computer (default). Result Codes: n=0,1 ERROR Otherwise Hook control This command instructs the modem to go on-hook to disconnect a call, or off-hook to make the phone line busy. Modem goes on-hook (default).
  • Page 222 AT Commands Result Codes: n=0,1,2,3 ERROR Otherwise Modulation handshake This command controls whether or not the local modem performs a negotiated handshake at connection time with the remote modem when the communication speed of the two modems is different. When originating or answering, this is for handshake only at the communication standard specified by S37 and the ATB command.
  • Page 223 AT Commands Result Codes: n=0,1 ERROR Otherwise Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric...
  • Page 224 AT Commands X4 (default) Enable Enable OK, RING, NO CARRIER, ERROR, NODIALTONE, BUSY, CONNECT <RATE>, DELAYED, BLACKLISTED, REORDER, WARBLE, CALL WAITING DETECTED Enable Enable OK, RING, NO CARRIER, ERROR, NODIALTONE, BUSY, CONNECT <RATE>, RRING, NO BONGTONE, DELAYED, BLACKLISTED, REORDER, WARBLE, CALL WAITING DETECTED Dial tone detect Disabled: The modem dials a call regardless of whether it detects a dial...
  • Page 225 AT Commands Result Codes: n=0,1 ERROR Otherwise &Dn DTR control This command interprets how the modem responds to the state of the DTR signal and changes to the DTR signal. &D0 Ignore. The modem ignores the true status of DTR and treats it as always on.
  • Page 226 AT Commands Result Codes: n=0,3,4 ERROR Otherwise &Pn Select Pulse Dial Make/Break Ratio (WW) &P0 Selects 39% - 61% make/break ratio at 10 pulses per second. &P1 Selects 33% - 67% make/break ratio at 10 pulses per second. &P2 Selects 33% - 67% make/break ratio at 20 pulses per second.
  • Page 227 AT Commands &Zn=x Store telephone number This command is used to store up to four dialing strings in the modem’s nonvolatile memory for later dialing. The format for the command is &Zn=“stored number” where n is the location 0-3 to which the number should be written.
  • Page 228 AT Commands Enable protocol result code appended to DCE speed (default). Result Codes: n=0,1 ERROR Otherwise View numbers in blacklist If blacklisting is in effect, this command displays the numbers for which the last call attempted in the past two hours failed. The ERROR result code appears in regions that do not require blacklisting.
  • Page 229: Appendix D S-Registers

    Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connection fails.
  • Page 230 S-registers Range: 0-255 Default: 0 Units: rings Ring counter This register is read only. The value of S1 is incremented with each ring. If no ring occurs over a six-second interval, this register is cleared. Range: 0-225 Default: 0 Units: rings AT escape character (user defined) This register determines the ASCII values used for an escape...
  • Page 231 S-registers Command line editing character (user defined) This register sets the character recognized as a backspace and pertains to asynchronous only. The modem will not recognize the backspace character if it is set to a value that is greater than 32 ASCII.
  • Page 232 S-registers Comma pause time This register sets the time, in seconds, that the modem must pause when it encounters a comma (,) in the dial command string. In some countries/regions, S8 will set both wait before dialing and comma pause time. Range: 0-255 Default: 2 Units:...
  • Page 233 S-registers S37 Dial line rate S37 = 0 (default) maximum modem speed S37 = 1 reserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 reserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37 = 8...
  • Page 234: At Command Set Result Codes

    S-registers AT command set result codes The following table shows the result codes. The result code summary Result Code Numeric Description Command executed CONNECT Modem connected to line RING A ring signal has been detected NO CARRIER Modem lost carrier signal, or does not detect carrier signal, or does not detect answer tone...
  • Page 235 S-registers CONNECT 33600 EC* Connection at 33600 bps DELAYED* Delay is in effect for the dialed number BLACKLISTED* Dialed number is blacklisted BLACKLIST FULL* Blacklist is full *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V.42bis - V.42 error control and V.42bis data compression.
  • Page 236 S-registers User’s Manual...
  • Page 237 Appendix E V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably.
  • Page 238 V.90 Table E-1 Result codes for a V.90 connection Result code Description CONNECT 32000 EC* Connection at 32000 bps CONNECT 36000 EC* Connection at 36000 bps CONNECT 40000 EC* Connection at 40000 bps CONNECT 44000 EC* Connection at 44000 bps CONNECT 48000 EC* Connection at 48000 bps CONNECT 52000 EC*...
  • Page 239 V.90 * EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V.42 error control and V.42bis data compression V.42 error control only NoEC No error control protocol...
  • Page 240 V.90 User’s Manual...
  • Page 241: Card Specifications

    Appendix F Wireless LAN Card Specifications Form Factor PCI-Ex MiniCard Type ■ IEEE 802.11 Standard for Wireless LANS Compatibility ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance. ■...
  • Page 242 Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions.
  • Page 243 Wireless LAN 2452 2457* 2462 2467* 2472* *1 Factory-set default channels *2 Refer to the sheet Approved Countries/Regions for use for the countries/ regions that in which these channels can be used. When installing Wireless LAN cards, the channel configuration is managed as follows: ■...
  • Page 244 Wireless LAN 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5745 5765 5785 5805 5825 User’s Manual...
  • Page 245 Appendix G Bluetooth wireless technology Interoperability Bluetooth Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ■ Bluetooth Specification Ver2.0+EDR, as defined and approved by The Bluetooth Special Interest Group.
  • Page 246 TOSHIBA portable computers. Always use Bluetooth Cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe...
  • Page 247: Bluetooth Wireless Technology And Your Health

    Because products with Bluetooth wireless technology operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Bluetooth wireless technology is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
  • Page 248 -Consult the dealer or an experienced radio/TV technician for help. TOSHIBA is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this Bluetooth Card from TOSHIBA, or the substitution or attachment of connecting cables and equipment other than specified by TOSHIBA.
  • Page 249 FCC radio frequency exposure limits. Nevertheless, the Bluetooth Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized. In normal operating configuration, the LCD in the upright position, the distance between the antenna and the user should not be less than 20cm.
  • Page 250 3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations. 2. Indication The indication shown below appears on this equipment.
  • Page 251: Device Authorization

    Bluetooth wireless technology Interoperability 3. TOSHIBA Direct PC Monday - Friday: 10:00-17:00 Toll Free Tel : 0120-15-1048 Direct Dial : 03-3457-4850 : 03-3457-4868 Device Authorization This device obtains the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Telecommunications Business Law.
  • Page 252 Bluetooth wireless technology Interoperability User’s Manual...
  • Page 253: Ac Power Cord And Connectors

    Appendix H AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters...
  • Page 254 AC Power Cord and Connectors Finland: FIMKO Sweden: SEMKO France: LCIE Switzerland: Germany: United Kingdom: In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 2- 15P (250V) or 1-15P (125V) and three pin plug configuration must be 6- 15P (250V) or 5-15P (125V) as designated in the U.S.
  • Page 255 BIOS and Hard Disk Drive to gain access to the system. To set permission and limits for the TOSHIBA Anti-theft Protection Timer please use the TOSHIBA Password Utility. The settings can only be activated or modified by a user with supervisor authority.
  • Page 256 TOSHIBA Anti-theft Protection Timer User’s Manual...
  • Page 257 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP: accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange BIOS: basic input output system CD-ROM: Compact Disc-Read Only Memory CD-RW: Compact Disc-ReWritable...
  • Page 258 VRT: voltage reduction technology WXGA: wide extended graphics array XGA: extended graphics array AccuPoint: A pointing device integrated into the TOSHIBA computer keyboard. adaptor: A device that provides an interface between two dissimilar electronic devices. For example, the AC adaptor modifies the power from a wall outlet for use by the computer.
  • Page 259 Glossary analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements.
  • Page 260 Glossary bus: An interface for transmission of signals, data or electric power. byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. cache memory: High speed memory which stores data that increases processor speed and data transfer rate.
  • Page 261 Glossary compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component.
  • Page 262 Glossary delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information.
  • Page 263 (FDD): An electromechanical device that reads and writes to floppy disks. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk.
  • Page 264 Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator panel.
  • Page 265 Glossary jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte.
  • Page 266 Glossary mode: A method of operation, for example, the boot mode, Standby Mode or the Hibernation Mode. modem: Derived from modulator/demodulator, a device that converts (modulates) digital data for transmission over telephone lines and then converts modulated data (demodulates) to digital format where received.
  • Page 267 The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver Utility: A TOSHIBA utility that lets you set the parameters for various power-saving functions. printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached.
  • Page 268 Glossary restart: Resetting a computer without turning it off (also called “warm boot” or “soft reset”). See also boot. RGB: Red, green, and blue. A device that uses three input signals, each activating an electron gun for a primary additive color (red, green, and blue) or port for using such a device.
  • Page 269 TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
  • Page 270 Glossary Glossary-14 User’s Manual...
  • Page 271 1-17, 8-10 hinge, 2-10 connecting, 3-2 opening, 3-4 Advanced Port Replicator III screen, 2-10 Plus, 1-17, 8-15 DLA for TOSHIBA, 1-16, 4-22 ASCII characters, 5-9 Docking interface, 1-8, 2-7 Documentation list, 1-2 Dual Pointing Device, 1-7 Battery AccuPoint, 1-7, 2-10, 4-2...
  • Page 272 Index display selection, 5-5 instant security, 5-4 Fingerprint Sensor Internal LCD screen bright- location, 2-9, 4-1 ness decrease, 5-5 problems, 9-16 Internal LCD screen bright- using, 4-3 ness increase, 5-5 Floppy disk care, 4-25 power save mode, 5-4 Fn + Ctrl (enhanced keyboard sound mute, 5-3 simulation), 5-3 standby, 5-4...
  • Page 273 Index Numeric mode, 5-8 inserting, 8-2 temporarily using normal location of slot, 2-3 keyboard (overlay removing, 8-3 on), 5-8 Ports temporarily using overlay Docking, 1-8 (overlay off), 5-8 external monitor, 1-7 turning on the overlays, 5-7 i.LINK, 1-8 Serial, 1-7 USB, 1-8 LAN, 1-9, 4-34 Power...
  • Page 274 RecordNow!, 1-15, 4-20 TOSHIBA Power Saver, 1-13 Recovery HDD, 3-10 TOSHIBA Presentation button, Recovery Media, 3-11 1-11 Restarting the computer, 3-9 TOSHIBA SD Memory Boot Util- ity, 1-15 TOSHIBA Zooming Utility, 1-15 SD card, 1-8 TV, 8-11 care, 8-5 formatting, 8-4...
  • Page 275 Index Wireless communication, 4-30 indicator, 2-12, 4-33 Wireless communication switch, 1-10, 2-2, 4-33 Wireless LAN, 1-10, 4-30 problems, 9-20 User’s Manual Index-5...
  • Page 276 Index Index-6 User’s Manual...

This manual is also suitable for:

Satellite pro a120

Table of Contents