Honeywell RTH2310 Quick Installation Manual

Programmable thermostat
Table of Contents

Advertisement

Available languages

Available languages

Quick Installation Guide
RTH2310
Programmable Thermostat
69-2214ES-04

Advertisement

Table of Contents
loading

Summary of Contents for Honeywell RTH2310

  • Page 1 Quick Installation Guide RTH2310 Programmable Thermostat 69-2214ES-04...
  • Page 2: Installation Is Easy

    Quick Installation Guide Installation is Easy Your new thermostat has been designed for fast and easy installation. Just follow the simple step-by-step instructions in the following pages. Identify your system type. Remove your old thermostat. Identify the wires. Mount the new wallplate. Connect the wires.
  • Page 3 RTH2310 Programmable Thermostat Identify System Type This thermostat is compatible with the following systems: • Gas, oil or electric furnace • Central air conditioner • a hot water system with or without pump • a millivolt system • a central heating and cooling system If you are not sure of your system type or if you have any other questions, call us toll-free at 1-800-468-1502.
  • Page 4: Remove Old Thermostat

    Quick Installation Guide Remove Old Thermostat Turn power off at the heating/cooling system. Remove old thermostat, but leave wallplate with wires attached. Do not remove wallplate yet. MERCURY NOTICE: Do not put your old thermostat in the trash if it contains mercury in a sealed tube.
  • Page 5: Identify Wires

    RTH2310 Programmable Thermostat Identify Wires If any wires are not attached to your old thermostat or are attached to a terminal marked C or C1, they will not be connected to your new thermostat. Wrap the bare metal end of each of these wires with electrical tape, so it cannot touch and short other wires.
  • Page 6: Mount New Wallplate

    Quick Installation Guide Mount New Wallplate Remove coverplate. Loosen screw (the screw remains captive on wallplate). Remove thermostat. Mark and drill appropriate mounting holes (or use existing holes). Insert plastic anchors. Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
  • Page 7: Typical Wiring

    RTH2310 Programmable Thermostat Connect Wires (typical wiring) Remove jumper if you have both R and Rc wires. Match each labeled wire with the terminal having the same letter. Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
  • Page 8: Less Common Wiring

    Quick Installation Guide Connect Wires (less common wiring) If a labeled wire does not match any terminal designation, see diagram below. Do not use C, X or B. Wrap bare end of wire with electrical tape. If wires are connected to both Rh and Rc terminals, remove jumper (see previous page).
  • Page 9: Specify Furnace Type

    RTH2310 Programmable Thermostat Specify Furnace Type Set the Jumper J2, on the back of the thermostat, if you have connected a wire to the G terminal. J2 jumper Leave the jumper in this factory-set position if you have a gas or oil furnace.
  • Page 10: Install Batteries

    Quick Installation Guide Install Batteries Pull out the battery cover. Install the batteries as shown. Observe the polarity. Reinstall the battery cover. You will hear a clicking sound. After the batteries are installed, the thermostat per- forms a series of tests for approximately 5 seconds. Afterwards, the screen displays the actual tempera- ture.
  • Page 11: Install Thermostat

    RTH2310 Programmable Thermostat Install thermostat Mount the thermostat on the wallplate. Tighten the screw and install the coverplate. Turn power back on at the heating/cooling system.
  • Page 12: System Setup

    Quick Installation Guide System Setup Press both buttons simultaneously for 3 seconds to enter or exit the setup menu. To advance to the next function, briefly press both buttons simultaneously. To change the setting, press the button. DISPLAY DESCRIPTION OPTIONS Temperature display °C or °F Time display...
  • Page 13: Guía De Instalación Rápida

    Guía de instalación rápida RTH2310 Termostato programable 69-2214ES-04...
  • Page 14: Instalación Fácil

    Guía de instalación rápida Instalación fácil El nuevo termostato ha sido concebido para que su instalación sea fácil. Sólo hay que seguir las instrucciones de las páginas siguientes. Identificar el tipo de sistema. Retirar el viejo termostato. Identificar los cables. Montar la nueva placa mural.
  • Page 15: Identificar El Tipo De Sistema

    Termostato programable RTH2310 Identificar el tipo de sistema Este termostato es compatible con los siguientes sistemas: • Calefactor a gas, aceite o eléctrico • Aire acondicionado central • Sistema de agua caliente con o sin bomba • Sistema de milivoltios •...
  • Page 16: Retirar El Viejo Termostato

    Guía de instalación rápida Retirar el viejo termostato Cortar la electricidad del sistema de calefacción/ aire acondicionado. Retirar el viejo termostato pero dejar la placa mural con los cables conectados. No retirar la placa mural todavía ADVERTENCIA SOBRE EL MERCURIO: no ponga su viejo termostato en la basura si contiene mercurio...
  • Page 17: Identificar Los Cables

    Termostato programable RTH2310 Identificar los cables Si en el viejo termostato hubiera cables no conectados o si estuvieran fijados a un terminal marcado C o C1, estos cables no se conectarán al nuevo termostato. Recubrir el extremo de metal desnudo de cada uno con cinta aisladora para que no puedan tocarse y producir un corto circuito.
  • Page 18 Guía de instalación rápida Instalar la nueva placa mural Retirar la placa de cubierta. Aflojar los tornillos (que quedarán cautivos en la placa mural). Retirar el termostato. Marcar y perforar los agujeros de montaje apropiados (o usar los existentes). Introducir los anclajes plásticos.
  • Page 19 Termostato programable RTH2310 Conectar los cables (conexión típica) Retirar el puente si hay cables R y Hacer coincidir cada cable etiquetado con el terminal de la misma letra. Aflojar los cables del terminal con un destornillador, luego ajustar los tornillos.
  • Page 20 Guía de instalación rápida Conectar los cables (conexión menos común) Si un cable etiquetado no coincide con la designación de ningún terminal, referirse al diagrama siguiente: No usar C, X o B. Enroscar el extremo desnudo con cinta aisladora. Si los cables están conectados con los terminales Rh y Rc, retirar el puente (ver la página previa).
  • Page 21: Especificar El Tipo De Estufa

    Termostato programable RTH2310 Especificar el tipo de estufa La posición del cable de puente J2, en la parte poste- rior del termostato, es importante si se conectó un cable al terminal G. Puente J2 Dejar el puente en esta posición en el caso de un sistema de calefacción a gas...
  • Page 22: Instalar Las Pilas

    Guía de instalación rápida Instalar las pilas Retirar la cubierta de las pilas. Instalar las pilas como se indica en el dibujo. Respetar la polaridad. Reinstalar la cubierta de las pilas. Se escuchará un clic. Luego de instalar las pilas, el termostato hace una serie de pruebas por alrededor de 5 segundos.
  • Page 23: Instalar El Termostato

    Termostato programable RTH2310 Instalar el termostato Montar el termostato en la placa mural. Ajustar los tornillos e instalar la placa de cubierta. Conectar el sistema de calefacción/aire acondicionado a la electricidad.
  • Page 24 Guía de instalación rápida Configuración del sistema Presionar los botones simultáneamente durante 3 segundos para entrar o salir del menú de configuración. Para avanzar a la siguiente función, presionar brevemente simultáneamente. Para cambiar la configuración, presionar los botones PANTALLA DESCRIPCIÓN OPCIONES Visualización de temperatura °C ó...

Table of Contents