Summary of Contents for Juniper J-series Services Router J4350
Page 1
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Release 9.2 Juniper Networks, Inc. 1194 North Mathilda Avenue Sunnyvale, California 94089 408-745-2000 www.juniper.net Part Number: 530-025360-01, Revision 1...
Page 2
Products made or sold by Juniper Networks or components thereof might be covered by one or more of the following patents that are owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312, 6,429,706, 6,459,579, 6,493,347, 6,538,518, 6,538,899, 6,552,918, 6,567,902, 6,578,186, and 6,590,785.
Page 3
AND (B) YOU MAY CONTACT JUNIPER NETWORKS REGARDING LICENSE TERMS. 1. The Parties. The parties to this Agreement are Juniper Networks, Inc. and its subsidiaries (collectively “Juniper”), and the person or organization that originally purchased from Juniper or an authorized Juniper reseller the applicable license(s) for use of the Software (“Customer”) (collectively, the “Parties”).
Page 4
(“GPL”) or the GNU Library General Public License (“LGPL”)), Juniper will make such source code portions (including Juniper modifications, as appropriate) available upon request for a period of up to three years from the date of distribution. Such request can be made in writing to Juniper Networks, Inc., 1194 N.
Page 5
Abbreviated Table of Contents About This Guide Part 1 J-series Overview Chapter 1 Overview of Services Routers Chapter 2 System Overview Chapter 3 PIM and VoIP Module Overview Chapter 4 Services Router User Interface Overview Part 2 Installing a Services Router Chapter 5 Preparing for Router Installation Chapter 6...
Page 6
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide...
Table of Contents About This Guide Objectives ...xv Audience ...xv How to Use This Guide ...xvi Document Conventions ...xvii Related Juniper Networks Documentation ...xviii Documentation Feedback ...xxi Requesting Technical Support ...xxi Part 1 J-series Overview Chapter 1 Overview of Services Routers J2320 Services Router Overview ...3...
Page 8
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide J2320 Power System ...24 J2350 Power System ...24 J2320 and J2350 Cooling System ...25 J4350 and J6350 Services Router Hardware Features ...26 J4350 and J6350 Chassis ...27 J4350 and J6350 Midplane ...31 J4350 and J6350 Routing Engine Hardware ...31 J4350 and J6350 Boot Devices ...31 J4350 and J6350 Front Panel ...32...
Page 9
TIM514 Analog Telephony Interface Module ...75 TIM516 Analog Telephony Interface Module ...76 TIM518 Analog Telephony Interface Module ...78 TIM521 BRI Telephony Interface Module ...79 Chapter 4 Services Router User Interface Overview User Interface Overview ...81 J-Web Overview ...81 CLI Overview ...82 Before You Begin ...82 Using the J-Web Interface ...83 Starting the J-Web Interface ...83...
Page 10
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Power Guidelines, Requirements, and Specifications ...107 Site Electrical Wiring Guidelines ...108 Router Power Requirements ...109 AC Power, Connection, and Power Cord Specifications ...109 DC Power, Connection, and Power Cable Specifications ...111 Planning for Power Management ...112 Network Cable Specifications ...115 ISDN Provisioning ...115...
Page 11
Configuring Basic Settings with a Configuration Editor ...147 Verifying Basic Connectivity ...150 Displaying Basic Connectivity Configurations ...150 Chapter 8 Configuring Secure Web Access Secure Web Access Terms ...153 Secure Web Access Overview ...154 Before You Begin ...154 Generating SSL Certificates ...155 Configuring Secure Web Access ...155 Configuring Secure Web Access with a Configuration Editor ...158 Verifying Secure Web Access ...159...
Page 12
Chapter 11 Troubleshooting Hardware Components Chassis Alarm Conditions ...209 Troubleshooting Power Management ...210 Contacting the Juniper Networks Technical Assistance Center ...212 Chapter 12 Contacting Customer Support and Returning Hardware Locating Component Serial Numbers ...213 J2320 and J2350 Chassis Serial Number and Agency Labels ...214 J4350 and J6350 Chassis Serial Number and Agency Labels ...215...
Objectives on page xv Audience on page xv How to Use This Guide on page xvi Document Conventions on page xvii Related Juniper Networks Documentation on page xviii Documentation Feedback on page xxi Requesting Technical Support on page xxi Objectives This guide contains an overview, basic instructions, and specifications for J2320, J2350, J4350, and J6350 Services Routers.
Page 16
JUNOS implementation specifically on J-series routers. (For comprehensive JUNOS information, see the JUNOS software manuals listed in “Related Juniper Networks Documentation” on page xviii.) Table 1 on page xvi shows the location of J-series information, by task type, in Juniper Networks documentation.
Page 17
more extensive configuration, use the J-Web configuration editor or CLI configuration mode commands. To monitor, diagnose, and manage a router, use the J-Web interface or CLI operational mode commands. Document Conventions Table 2 on page xvii defines the notice icons used in this guide. Table 2: Notice Icons Icon Meaning...
Page 18
J-Web GUI Conventions Bold text like this > (bold right angle bracket) Related Juniper Networks Documentation J-series Services Routers are documented in multiple guides. Although the J-series guides provide instructions for configuring and managing a Services Router with the JUNOS CLI, they are not a comprehensive JUNOS software resource. For complete...
Page 19
JUNOS Interfaces Command Reference JUNOS Network Interfaces Configuration Guide JUNOS System Basics Configuration Guide JUNOS System Basics and Services Command Reference JUNOS Routing Protocols Configuration Guide JUNOS Routing Protocols and Policies Command Reference Related Juniper Networks Documentation About This Guide...
Page 20
“Configuring SNMP for Network Management” “Configuring the Router as a DHCP Server” “Configuring Autoinstallation” “Automating Network Operations and Troubleshooting” Related Juniper Networks Documentation Corresponding JUNOS Software Manual JUNOS MPLS Applications Configuration Guide JUNOS Routing Protocols and Policies Command Reference JUNOS VPNs Configuration Guide...
Page 21
Software release version (not required for Network Operations Guides [NOGs]) Requesting Technical Support Technical product support is available through the Juniper Networks Technical Assistance Center (JTAC). If you are a customer with an active J-Care or JNASC support contract, or are covered under warranty, and need postsales technical support, you can access our tools and resources online or open a case with JTAC.
Page 22
7 days a week, 365 days a year. Self-Help Online Tools and Resources For quick and easy problem resolution, Juniper Networks has designed an online self-service portal called the Customer Support Center (CSC) that provides you with the following features:...
Part 1 J-series Overview Overview of Services Routers on page 3 System Overview on page 13 PIM and VoIP Module Overview on page 43 Services Router User Interface Overview on page 81 J-series Overview...
Page 24
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide J-series Overview...
Quick Configuration wizards simplify basic configuration and minimize the risk of operator error. JUNOS command-line interface—A Juniper Networks command shell that runs on top of a UNIX-based operating system kernel. The CLI is a straightforward command interface. On a single line, you type commands that are executed when you press the Enter key.
Page 26
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide an external compact flash and two universal serial bus (USB) ports for external storage, and an optional Crypto Accelerator Module. J2320 routers ordered with the optional Crypto Accelerator Module come standard with 1 GB of memory, while those ordered without the Crypto Accelerator Module come standard with 256 MB of memory.
Page 27
upgraded to 1 GB. For instructions on upgrading memory, see “Replacing DRAM Modules” on page 188. Each J2350 chassis contains four built-in Gigabit Ethernet ports with link speeds of 10/100/1000 Mbps over a copper interface. The chassis also contains five slots for field-replaceable Physical Interface Modules (PIMs) and Avaya VoIP modules providing flexible WAN and voice connectivity options.
Page 28
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide The J4350 Services Router supports the following field-replaceable PIMs and Avaya VoIP modules: Gigabit Ethernet uPIM (1-port, 6-port, 8-port, and 16-port) SFP Gigabit Ethernet ePIM (1 port) Copper Gigabit Ethernet ePIM (1 port) Dual-Port Serial PIM Dual-Port E1 PIM Dual-Port T1 PIM...
Page 29
The J6350 Services Router supports the following field-replaceable PIMs and Avaya VoIP modules: Gigabit Ethernet uPIM (1–port, 6-port, 8-port, and 16-port) SFP Gigabit Ethernet ePIM (1 port) Copper Gigabit Ethernet ePIM (1 port) Dual-Port Serial PIM Dual-Port E1 PIM Dual-Port T1 PIM E3 PIM (1 port) DS3 (T3) PIM (1 port) Dual-Port Fast Ethernet PIM...
Page 30
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 5: Summary of J-series Features and License Requirements (continued) Feature Category J-series Feature Open Shortest Path First (OSPF) Routing and Multicast Border Gateway Protocol (BGP) Routing Information Protocol version 1 (RIPv1) and RIPv2 Static routes Intermediate System-to-Intermediate System (IS-IS) Connectionless Network Services (CLNS):...
Page 31
Table 5: Summary of J-series Features and License Requirements (continued) Feature Category J-series Feature Ethernet: Encapsulation Media access control (MAC) encapsulation 802.1p tagging Point-to-Point Protocol over Ethernet (PPPoE) Asynchronous Transfer Mode (ATM) for asymmetric digital subscriber line (ADSL) or symmetric high-speed digital subscriber line (SHDSL) Circuit cross-connect (CCC) Translational cross-connect (TCC) Synchronous Point-to-Point Protocol (PPP)
Page 32
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 5: Summary of J-series Features and License Requirements (continued) Feature Category J-series Feature Common Criteria Security Network attack detection Denial-of-service (DoS) and distributed DoS protection Generic routing encapsulation (GRE), IP-over-IP, and IP Security (IPSec) tunnels Advanced Encryption Standard (AES) 128-, 192-, and 256-bit.
Page 33
Table 5: Summary of J-series Features and License Requirements (continued) Feature Category J-series Feature System log Activity Logging and Monitoring J-Web event viewer Traceroute Supports the following external administrator databases: Administration RADIUS TACACS+ Autoinstallation Configuration rollback Button-operated configuration rescue (CONFIG) Confirmation of configuration changes Software upgrades Supports the following features for automating network operations and...
Chapter 2 System Overview J-series J2320, J2350, J4350, and J6350 Services Routers have chassis that are similar but with important differences. J2320, J2350, and J4350 routers have a single nonredundant power supply and an optional Crypto Accelerator Module. J6350 routers have redundant power supplies and a standard Crypto Accelerator Module. For field-replaceable PIMs and Avaya VoIP modules, the J2320 has three slots, the J2350 has five slots, and the J4350 and J6350 have six slots.
Page 36
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide In addition to the components described in subsequent sections, the chassis includes the following components: Mounting brackets—One pair of metal brackets can be mounted at the front or center of the chassis for mounting the chassis in a rack or cabinet. Earthing terminal—A protective earthing terminal and a PEM nut at the rear of the chassis ensure safe dissipation of static electricity in all situations.
Page 37
Chapter 2: System Overview Figure 2: Front of J2350 Chassis Figure 3: Rear of J2320 Chassis Figure 4: Rear of J2350 AC-Powered Chassis J2320 and J2350 Services Router Hardware Features...
Page 38
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Figure 5: Rear of J2350 DC-Powered Chassis Figure 6: J2320 Hardware Components J2320 and J2350 Services Router Hardware Features...
Page 39
Figure 7: J2350 Hardware Components Table 6 on page 17 summarizes the physical specifications for the router chassis. Table 6: J2320 and J2350 Physical Specifications Description Value Chassis dimensions J2320 Services Router 1.75 in. (4.45 cm) high 17.51 in. (44.48 cm) wide—18.9 in. (48.01 cm) wide with mounting brackets attached 15.1 in.
Page 40
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide J2320 and J2350 Midplane The J2320 and J2350 midplane is located in the center of the chassis and forms the rear of the PIM card cage (see Figure 6 on page 16 and Figure 7 on page 17). You install the PIMs into the midplane from the front of the chassis.
J2320 and J2350 Boot Devices J2320 and J2350 Services Routers can boot from three devices: Internal compact flash External compact flash (also known as the removable compact flash) USB storage device Normally, a J2320 or J2350 Services Router boots from the internal compact flash. If the internal compact flash fails, the router attempts to boot from the external compact flash if it is installed.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide STATUS LED on page 21 ALARM LED on page 21 HA LED on page 22 RESET CONFIG Button on page 22 Built-In Gigabit Ethernet Ports on page 23 Console Port on page 23 AUX Port on page 23 USB Port on page 24 Physical Interface Modules (PIMs)
Table 7: J2320 and J2350 POWER LED Color State Green On steadily Blinking Unlit After the router is powered on, status indicators—such as LEDs on the front panel show chassis power supply is functioning normally. Ignore error indicators that appear during the first 60 seconds.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 9: J2320 and J2350 ALARM LED Color State On steadily Yellow On steadily Unlit For information about alarm conditions and corrective actions, see “Chassis Alarm Conditions” on page 209. For additional information, see the J-series Services Router Administration Guide.
You can change the default behavior of the information, see the J-series Services Router Basic LAN and WAN Access Configuration Guide. Built-In Gigabit Ethernet Ports Four built-in Gigabit Ethernet ports provide LAN connections over copper interfaces to hubs, switches, local servers, and workstations. You can also designate an Ethernet port for management traffic.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide USB Port ports on the front panel of the router (see Figure 8 on page 19 and Figure 9 on page 19) accept a USB storage device or USB storage device adapter with a compact flash installed, as defined in the CompactFlash Specification published by the CompactFlash Association.
Chapter 2: System Overview The AC power supply has a single AC appliance inlet that requires a dedicated AC power feed. The DC power supply has a terminal block that provides a single DC input (–48 VDC and return) and requires a dedicated 15 A (–48 VDC) circuit breaker. The J2350 AC-powered or DC-powered chassis has a power switch and does not include a power LED.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Figure 11: Airflow Through the J2320 Chassis Figure 12: Airflow Through the J2350 Chassis J4350 and J6350 Services Router Hardware Features This section contains the following topics: J4350 and J6350 Chassis on page 27 J4350 and J6350 Midplane on page 31 J4350 and J6350 Routing Engine Hardware on page 31 J4350 and J6350 Boot Devices on page 31...
J6350 Power System on page 37 J4350 and J6350 Cooling System on page 38 J4350 and J6350 Chassis The J4350 and J6350 chassis is a rigid sheet metal structure that houses all the other router components (see Figure 13 on page 28 through Figure 18 on page 30). The chassis can be installed in many types of racks or cabinets.
Page 50
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Figure 13: Front of J4350 and J6350 Chassis Figure 14: Rear of J4350 AC-Powered Chassis NOTE: The J4350 AC-powered chassis has a power switch and does not include a power supply LED (unlike the J6350 AC-powered chassis). Figure 15: Rear of J6350 AC-Powered Chassis J4350 and J6350 Services Router Hardware Features...
Page 51
Chapter 2: System Overview Figure 16: Rear of J4350 DC-Powered Chassis Figure 17: Rear of DC-Powered J6350 Chassis J4350 and J6350 Services Router Hardware Features...
Page 52
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Figure 18: J4350 and J6350 Hardware Components Table 11 on page 30 summarizes the physical specifications for the router chassis. Table 11: J4350 and J6350 Physical Specifications Description Value Chassis dimensions 3.44 in.
Page 53
J4350 and J6350 Midplane The midplane is located in the center of the chassis and forms the rear of the PIM card cage (see Figure 18 on page 30). You install the PIMs into the midplane from the front of the chassis. Data packets are transferred across the midplane from the PIM to the Routing Engine, and from the Routing Engine across the midplane to the destination PIM.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide J4350 and J6350 Front Panel The front panel of the Services Router (see Figure 19 on page 32) allows you to install or remove PIMs, view router status LEDs, access the console port, and perform simple control functions.
Figure 20: Slot Number Diagram on Front Panel Gigabit Ethernet and 4-port Fast Ethernet ePIMs can be installed in high-speed slots only. High-speed slots are indicated by a black triangle containing an E in the front panel slot number diagram. On J4350 Services Routers, the high-speed slots are slot 3 and slot 6.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide off and on again, we recommend waiting a few seconds between shutting it down and powering it back up. Table 13 on page 34 describes the Table 13: STATUS LED Color State Green...
RESET CONFIG Button Use the RESET CONFIG or the factory default configuration. The button is recessed to prevent it from being pressed accidentally. To press this button insert a small probe (such as a straightened paper clip) into the pinhole on the front panel (see Figure 19 on page 32). For example, if someone inadvertently commits a configuration that denies management access to a Services Router, you can delete the invalid configuration and replace it with a rescue configuration by pressing the...
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Console Port You can use the console port on the chassis front panel to connect to the Routing Engine through an RJ-45 serial cable. From the chassis console port, you can use the CLI to configure the router.
Table 16: Power Supply LED State Description No power is flowing to the power supply. Green Power supply is connected and power is flowing. Yellow Power supply is connected, but the router is not powered on. For information about site power preparations, see “Power Guidelines, Requirements, and Specifications”...
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide WARNING: DC-powered Services Routers are intended for installation only in a restricted access location. J4350 and J6350 Cooling System The cooling system includes three fans at the rear of the chassis. The airflow produced by these fans keeps router components within the acceptable temperature range (see Figure 21 on page 39).
Figure 21: Airflow Through the J4350 and J6350 Chassis Software Overview Each J-series Services Router runs the JUNOS software on its general-purpose processors. Designed for the large production networks typically supported by Internet service providers (ISPs), the JUNOS software includes processes for Internet Protocol (IP) routing and for managing interfaces, networks, and the router chassis.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Routing Engine and Packet Forwarding Engine A Services Router has two primary software processing components: Routing Engine—The Routing Engine provides three main functions: Creates the packet forwarding switch fabric for the Services Router, providing route lookup, filtering, and switching on incoming data packets, then directing outbound packets to the appropriate interface for transmission to the network.
Table 17: JUNOS Software Processes Process Name Management process Chassis chassisd process Routing protocol process Interface process (also called device control process) Forwarding fwdd process User Interfaces The user interfaces on a Services Router interact with the management process to execute commands and store and retrieve information from the configuration database.
Page 64
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide For more information, see “Services Router User Interface Overview” on page 81. Other user interfaces for the Services Router interact with the management process through the common API interface. These interfaces are designed to facilitate the configuration of one or, in some cases, many routers on the network.
Chapter 3 PIM and VoIP Module Overview J-series Services Routers accept Physical Interface Modules (PIMs) and Avaya VoIP modules in the slots on the front of the chassis. CAUTION: PIMs and VoIP modules are not hot-swappable. You must power off the Services Router before removing or inserting a PIM or VoIP module.
Page 66
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 18: PIM and VoIP Module Terms Term Definition ADSL 2/2+ Annex A ITU-T Standard G.992.1 that defines how ADSL works over plain old telephone service (POTS) lines. ADSL 2/2+ Annex B ITU-T Standard G.992.1 that defines how ADSL works over Integrated Services Digital Network (ISDN) lines.
Table 18: PIM and VoIP Module Terms (continued) Term Definition dialer filter Stateless firewall filter that enables dial-on-demand routing backup when applied to a physical ISDN interface and its dialer interface configured as a passive static route. The passive static route has a lower priority than dynamic routes. If all dynamic routes to an address are lost from the routing table and the router receives a packet for that address, the dialer interface initiates an ISDN backup connection and sends the packet over it.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Field-Replaceable PIMs PIMs are removable and insertable only when the Services Router is powered off. You can install a PIM into one of the slots in the router chassis. If a slot is not occupied by a PIM, a PIM blank panel must be installed to shield the empty slot and to allow cooling air to circulate properly through the router.
Page 69
Table 19: J2320 and J2350 Field-Replaceable PIM Summary Supported Software Releases for This PIM 1-Port SFP, 6-Port SFP, JUNOS 8.4 and later 8-Port, and 16-Port Gigabit Ethernet uPIMs Dual-Port Serial PIM JUNOS 8.4 and later Dual-Port T1 or E1 PIM JUNOS 8.4 and later Dual-Port Channelized JUNOS 8.4 and later...
Page 70
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 20: J4350 and J6350 Field-Replaceable PIM and Module Summary Supported Software Releases for This PIM 1-Port SFP Gigabit JUNOS 8.4 and later Ethernet uPIM 6-Port SFP Gigabit JUNOS 8.3 and later Ethernet uPIM 8-Port Gigabit Ethernet JUNOS 8.3 and later...
Page 71
Table 20: J4350 and J6350 Field-Replaceable PIM and Module Summary (continued) Supported Software Releases for This PIM 4-port Fast Ethernet JUNOS 8.0 and later ePIM PIM 4-Port ISDN BRI PIM JUNOS 8.0 and later ADSL PIM JUNOS 8.0 and later G.SHDSL PIM JUNOS 8.0 and later 1-Port, 6-Port, 8-Port, and 16-Port Gigabit Ethernet uPIMs...
Page 72
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Figure 23: 6-Port Gigabit Ethernet uPIM The 8-port and 16-port Gigabit Ethernet uPIMs, shown in Figure 24 on page 50 and Figure 25 on page 50, have RJ-45 connectors. Figure 24: 8-Port Gigabit Ethernet uPIM Figure 25: 16-Port Gigabit Ethernet uPIM Features.
Page 73
1000Base-SX, 1000Base-LX, and 1000Base-T SFPs. They do not support 1000Base-LH SFPs. 1000Base-SX and 1000Base-LX SFP transceivers have the following characteristics: Duplex LC/PC connector (Rx and Tx). Optical interface support—See the J-series Services Router Administration Guide. 8-port and 16-port Gigabit Ethernet uPIMs—and SFPs on the 1-port and 6-port uPIMs—support 1000Base-T RJ-45 connectors.
Page 74
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide For alarms, see the configuring and monitoring alarms information in the J-series Services Router Administration Guide. Optical Interface Support. Table 22 on page 52 describes the optical interface support on the 1-port and 6-port Gigabit Ethernet uPIMs over single-mode fiber-optic (SMF) and multimode fiber-optic (MMF) cables.
Page 75
Figure 27: SFP Gigabit Ethernet ePIM Features. The Gigabit Ethernet ePIM provides the following key features: Autonegotiation through medium-dependent interface (MDI) and MDI crossover (MDI-X) support. Link speeds for the Copper Gigabit Ethernet ePIM are configurable to 10, 100, or 1000 Mbps, and transmission mode is configurable to half or full duplex. The SFP Gigabit Ethernet ePIM cannot be manually configured—it is set at 1000 Mbps and full duplex.
Page 76
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide NOTE: High-speed slots are labeled with an E on the front-panel slot number diagram. To install or remove a PIM, see “Replacing a PIM” on page 172. Interface LEDs. The Table 23 on page 54 describes the meaning of the LEDs.
Page 77
Dual-Port Serial PIM The Dual-Port Serial PIM (Figure 28 on page 55) provides a physical connection to serial network media types through two serial interface ports. Figure 28: Dual-Port Serial PIM The Dual-Port Serial PIM provides the following key features: Onboard network processor Autoselection of operation modes based on data terminal equipment (DTE) or data communication equipment (DCE) cables...
Page 78
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Dual-Port T1 or E1 PIM The Dual-Port T1 PIM (Figure 29 on page 56) and Dual-Port E1 PIM (Figure 30 on page 56) provide a physical connection to T1 or E1 network media types.
Page 79
Table 26: Status LEDs for T1 and E1 Ports Color Green Unlit For alarms, see the configuring and monitoring alarms information in the J-series Services Router Administration Guide. Dual-Port Channelized T1/E1/ISDN PRI PIM The Dual-Port Channelized T1/E1/ISDN PRI PIM (Figure 31 on page 57) is a multiflex interface card that allows you to configure a single interface as a channelized T1 interface or a channelized E1 interface.
Page 80
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Maximum MTU value of 4500 bytes (for channelized T1 or E1 interface) and 4098 bytes (for ISDN PRI services) NOTE: For a clear-channel T1 or E1 interface, the maximum MTU is 9150 bytes. 56-Kbps and 64-Kbps modes ANSI T1.102, T1.107, and T1.403 standards compliance G.703, G.704, and G.706 E1 standards compliance...
For alarms, see the configuring and monitoring alarms information in the J-series Services Router Administration Guide. T3 or E3 PIM The T3 (also known as DS3) PIM (Figure 32 on page 59) and E3 PIM (Figure 33 on page 59) provide a physical connection to T3 or E3 network media types.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 28: Status LEDs for T3 and E3 Ports Color Green Yellow Unlit For alarms, see the configuring and monitoring alarms information in the J-series Services Router Administration Guide. Dual-Port Fast Ethernet PIM The Dual-Port 10/100-Mbps Fast Ethernet PIM (Figure 34 on page 60) has two physical Fast Ethernet ports.
Table 29: LEDs for Dual-Port Fast Ethernet PIM Label Color Green (100 Mbps) LINK/SPEED Yellow (10 Mbps) Green ACTIVITY Green For alarms, see the configuring and monitoring alarms information in the J-series Services Router Administration Guide. 4-Port Fast Ethernet ePIM You can install 4-Port Fast Ethernet ePIMs in any of the high-speed slots, as follows: J4350—Install up to two 4-Port Fast Ethernet ePIMs in slots 3 and 6.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide For pinouts of cable connectors for Fast Ethernet ePIMs, see “Fast Ethernet RJ-45 Connector Pinout” on page 233. NOTE: 4-port Fast Ethernet ePIMs support a maximum frame size of 1514 bytes. Jumbo frames are not supported.
Page 85
Figure 37: ISDN BRI U PIM ISDN BRI PIMs provide the following key features: Onboard network processor Bandwidth on demand Dial backup Dial-on-demand routing backup (floating static and dialer watch) For pinouts of cable connectors for ISDN PIMs, see “ISDN RJ-45 Connector Pinout”...
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide For alarms, see the configuring and monitoring alarms information in the J-series Services Router Administration Guide. ADSL PIM The ADSL PIM provides a single physical interface to asymmetric digital subscriber line (ADSL) network media types.
Table 32: LEDs for ADSL PIMs Label Color Green ONLINE Unlit Green STATUS For alarms, see the configuring and monitoring alarms information in the J-series Services Router Administration Guide. G.SHDSL PIM The G.SHDSL PIM (Figure 40 on page 65) provides symmetric high-speed digital subscriber line (SHDSL) physical interfaces to ATM network media types.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Local and remote loopback diagnostics ITU-T G.991.2, ITU-T G.994.1, and ITU-T G.997.1 standards compliance NOTE: Payload loopback functionality is not supported on ATM-over-SHDSL interfaces. For pinouts of cable connectors for G.SHDSL PIMs, see “ADSL and G.SHDSL RJ-11 Connector Pinout”...
Avaya VoIP modules are described in the following sections: Avaya VoIP Module Summary on page 67 TGM550 Telephony Gateway Module on page 69 TIM508 Analog Telephony Interface Module on page 73 TIM510 E1/T1 Telephony Interface Module on page 74 TIM514 Analog Telephony Interface Module on page 75 TIM516 Analog Telephony Interface Module on page 76 TIM518 Analog Telephony Interface Module on page 78 TIM521 BRI Telephony Interface Module on page 79...
Page 90
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 34: J2320 and J2350 Avaya VoIP Module Summary (continued) Software Release for Also Called This PIM TIM510 E1/T1 TIM510 JUNOS 8.4 and later Telephony E1/T1 media Interface module Module TIM510 TIM514 TIM514...
Page 91
Table 35: J4350 and J6350 Avaya VoIP Module Summary (continued) Software Release for Also Called This PIM TIM508 TIM508 JUNOS 8.5 and later Analog media Telephony module Interface TIM508 Module TIM510 E1/T1 TIM510 JUNOS 8.2 and later Telephony E1/T1 media Interface module Module...
Page 92
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Figure 41: TGM550 Telephony Gateway Module The TGM550 provides the following key features: Voice VoIP Media Gateway services. Two analog telephone ( incoming analog direct inward dialing (DID) trunks with either wink start or immediate start.
Page 93
Table 36 on page 71 lists the maximum number of media servers, telephones, and so on that are supported by the TGM550 installed on a J4350 or J6350 or J2320 or J2350 Services Router. Table 36: TGM550 Maximum Media Gateway Capacities Hardware or Feature TGM550s that can be controlled by an Avaya S8500 or S8700 Media Server...
Page 94
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 36: TGM550 Maximum Media Gateway Capacities (continued) Hardware or Feature Busy Hour Call Completion Rate (BHCC) Total of IP and analog telephones that can be connected to a TGM550 and TIMs Touch-tone recognition (TTR) Tone generation Announcements (VAL)
For more information about the TGM550, see the Avaya manual Hardware Description and Reference for Avaya Communication Manager. TIM508 Analog Telephony Interface Module The TIM508 Analog Telephony Interface Module (Figure 42 on page 73), also known as the TIM508 analog media module, has eight analog telephone lines that can be used as trunk ports.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide TIM508 LEDs indicate link status and activity. Table 39 on page 74 describes the meaning of the LEDs. Table 39: LEDs for TIM508 Label Color Yellow For more information about the TIM508, see the Avaya manual Hardware Description and Reference for Avaya Communication Manager.
To install or remove an Avaya VoIP module, see “Replacing a PIM” on page 172. TIM510 LEDs indicate link status and activity. Table 40 on page 75 describes the meaning of the LEDs. Table 40: LEDs for TIM510 Label Color Green Yellow Green...
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 41: TIM514 Possible Port Configurations Possible Analog Telephone (LINE) Port Configurations Wink-start or immediate-start DID trunk Analog tip/ring devices such as single-line telephones with or without LED message-waiting indication The TIM514 also provides the following features: Three ringer loads, the ringer equivalency number for up to 2,000 ft (610 m), for all eight ports...
Page 99
Figure 45: TIM516 Analog Telephony Interface Module You can configure TIM516 lines as described in Table 43 on page 77. Table 43: TIM516 Possible Port Configurations Possible Analog Telephone (LINE) Line Configurations Analog tip/ring devices such as single-line telephones with or without LED message-waiting indication The TIM516 also provides the following features: Three ringer loads, the ringer equivalency number for up to 2,000 ft (610 m), for all 16 lines...
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide For more information about the TIM516, see the Avaya manual Hardware Description and Reference for Avaya Communication Manager. TIM518 Analog Telephony Interface Module The TIM518 Analog Telephony Interface Module (Figure 46 on page 78), also known as the TIM518 analog media module, has eight analog telephone lines and eight analog trunk lines.
For pinouts of cable connectors for the TIM518, see “TIM518 Connector Pinout” on page 244. To install or remove an Avaya VoIP module, see “Replacing a PIM” on page 172. TIM518 LEDs indicate link status and activity. Table 46 on page 79 describes the meaning of the LEDs.
Page 102
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide NOTE: The TIM521 does not support BRI stations or combining both B-channels together to form a 128-Kbps channel. Over a 16-Kbps channel, called the D-channel, that is used for signaling. The TIM521 occupies one time slot for all four D-channels The circuit-switched connections have an a-law or mu-law option for voice operation.
Chapter 4 Services Router User Interface Overview You can use two user interfaces to monitor, configure, troubleshoot, and manage a Services Router—the J-Web interface and the JUNOS command-line interface (CLI). This chapter contains the following topics: User Interface Overview on page 81 Before You Begin on page 82 Using the J-Web Interface on page 83 Using the Command-Line Interface on page 91...
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Edit the configuration in a text file. Upload a configuration file. The J-Web interface also allows you to manage configuration history and set a rescue configuration. Diagnosing—Diagnose routing problems by running the ping or traceroute diagnostic tool.
Using the J-Web Interface This section contains the following topics: Starting the J-Web Interface on page 83 J-Web Layout on page 83 Elements of the J-Web Interface on page 84 Navigating the J-Web Interface on page 87 J-Web Sessions on page 90 For more information about using the J-Web interface, see the J-Web Interface User Guide.
Page 106
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Top pane—Displays identifying information and links. Main pane—Location where you monitor, configure, diagnose, and manage the Services Router by entering information in text boxes, making selections, and clicking buttons. Side pane—Displays subtasks of the Monitor, Configuration, Diagnose, or Manage task currently displayed in the main pane.
The top pane comprises the elements shown in Figure 49 on page 85. Figure 49: Top Pane Elements Juniper Networks logo—Link to hostname – model—Hostname and model of the Services Router. Logged in as: username—Username you used to log in to the Services Router.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Figure 50: Main Pane Elements Help (?) icon—Displays useful information when you move the cursor over the question mark. This help displays field-specific information, such as the definition, format, and valid range of the field. Red asterisk (*)—Indicates a required field.
Figure 51: Side Pane Elements Subtask—Displays options related to the selected task in the J-Web taskbar. Configuration hierarchy—For the J-Web configuration editor, displays the hierarchy of committed statements in the Services Router configuration. Click Expand all to display the entire hierarchy. Click Hide all to display only the statements at the top level.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide The path displayed in the top right corner of each page provides a context. Use this path to see your location in a configuration hierarchy. Clicking any link in the path displays the corresponding page.
Configuration, Diagnose, Manage, Events, and Alarms tasks. For Help on the View and Edit configuration tasks, see the related documentation provided in the “Related Juniper Networks Documentation” on page xviii. To get Help in the J-Web interface: Field-sensitive Help—Move the cursor over the question mark (?) next to the field for which you want more information.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Figure 52: CoS Help Page J-Web Sessions You establish a J-Web session with the Services Router through an HTTP-enabled or HTTPS-enabled Web browser. The HTTPS protocol, which uses 128-bit encryption, is available only in domestic versions of the JUNOS software.
Using the Command-Line Interface This section contains the following topics: CLI Command Hierarchy on page 91 Starting the CLI on page 92 CLI Operational Mode on page 92 CLI Configuration Mode on page 93 CLI Basics on page 94 For more information about the CLI, see the JUNOS CLI User Guide. CLI Command Hierarchy The CLI commands are organized hierarchically, with commands that perform a similar function grouped together under the same level.
Page 114
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide intervening space), you see a list of commands that match the partial name you typed. Starting the CLI To start the CLI: Establish a connection with the Services Router: To access the router remotely from the network, enter the command you typically use to establish a remote connection (such as the router hostname.
show start telnet test traceroute At the top level of operational mode are a number of broad groups of CLI commands that are used to perform the following functions: Control the CLI environment. Monitor and troubleshoot the router. Connect to other systems. Manage files and software images.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide insert load quit rename rollback save show status wildcard The JUNOS software configuration consists of a hierarchy of statements. There are two types of statements: container statements, which contain other statements, and leaf statements, which do not contain other statements.
Page 117
Table 50: CLI Editing Keystrokes Task Category Action Move the cursor. Move the cursor back one character. Move the cursor back one word. Move the cursor forward one character. Move the cursor forward one word. Move the cursor to the end of the command line. Delete characters.
Page 118
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide To complete a command or option that you have partially typed, press Tab or Spacebar. If the partially typed letters uniquely identify a command, the complete command name appears. Otherwise, a message indicates that your entry is ambiguous or invalid.
Page 119
When you enter the displays usage guidelines and summary information for configuration statements and operational mode commands. You can enter configuration mode. Table 51: help Commands CLI Command help apropos string help reference string help topic string Configuring the CLI Environment You can configure the CLI environment for your current login session.
Page 120
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide user@host> set cli ? Possible completions: complete-on-space directory idle-timeout prompt restart-on-upgrade screen-length screen-width terminal Table 52 on page 98 shows how you can change the CLI environment features. Table 52: Configuring the CLI Environment Environment CLI Command Feature...
Page 121
Table 52: Configuring the CLI Environment (continued) Environment CLI Command Feature Number of CLI set cli screen-width characters displayed width on a line Your terminal type. set cli terminal terminal-type Chapter 4: Services Router User Interface Overview Default Setting Options Variable (depends on terminal type).
Page 122
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Using the Command-Line Interface...
Part 2 Installing a Services Router Preparing for Router Installation on page 103 Installing and Connecting a Services Router on page 117 Establishing Basic Connectivity on page 131 Configuring Secure Web Access on page 153 Installing and Managing J-series Licenses on page 161 Installing a Services Router...
Page 124
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Installing a Services Router...
Chapter 5 Preparing for Router Installation Before installing a J-series Services Router, make sure that your site has the proper operating environment and equipment. Use the checklist at the end of the chapter to help you prepare your site. This chapter discusses the following topics: General Site Guidelines on page 103 Rack Requirements on page 104 Router Environmental Tolerances on page 106...
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Rack Requirements J-series Services Routers must be installed in a rack. Many types of racks are acceptable, including front-mount racks, four-post (telco) racks, and center-mount racks. The following sections describe rack requirements: Rack Size and Strength for J2320 and J2350 Routers on page 104 Rack Size and Strength for J4350 and J6350 Routers on page 105 Connection to Building Structure on page 105...
Page 127
The J2320 chassis height of 1.75 in. (4.45 cm) equals 1 U. The J2350 chassis height of 2.61 in. (6.63 cm) equals 1.5 U. Each U is a standard rack unit defined in Cabinets, Racks, Panels, and Associated Equipment (document number EIA-310-D) published by the Electronics Industry Association.
In addition, establish procedures to protect your equipment in the event of a fire emergency. Juniper Networks products must be installed in an environment suitable for electronic equipment. We recommend that fire suppression equipment be available...
NOTE: To keep warranties effective, do not use a dry chemical fire extinguisher to control a fire at or near a Juniper Networks router. If a dry chemical fire extinguisher is used, the unit is no longer eligible for coverage under a service agreement.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Site Electrical Wiring Guidelines WARNING: Certain ports on the router are designed for use as intrabuilding (within-the-building) interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE cabling. To comply with NEBS requirements and protect against lightning surges and commercial power disturbances, the intrabuilding ports must not be metallically connected to interfaces that connect to the OSP or its wiring.
CAUTION: To comply with intrabuilding lightning/surge requirements, intrabuilding wiring must be shielded, and the shield for the wiring must be grounded at both ends. Router Power Requirements Table 54 on page 109 and Table 55 on page 109 list the AC and DC power system electrical specifications for J-series Services Routers.
Page 132
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Detachable AC power cords, each 2.5 m (approximately 8 ft) long, are supplied with the Services Router. The appliance coupler at the female end of the cord inserts into the appliance inlet on the faceplate of the AC power supply. The coupler is type C19 as described by International Electrotechnical Commission (IEC) standard 60320.
For information about the AC power supply, see “J2320 and J2350 Services Router Hardware Features” on page 13 and “J4350 and J6350 Services Router Hardware Features” on page 26. To connect the power cord during initial installation, see “Connecting Power” on page 124. To replace the AC power cord, see “Replacing AC Power Supply Cords”...
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide NOTE: Power cords and cables must not block access to router components or drape where people might trip on them. For information about the DC power supply, see “J2320 and J2350 Services Router Hardware Features”...
Page 135
Table 57: J-series PIM Power Consumption and Heat Dissipation Name Model Number 1-Port Gigabit JXU-SFP-S Ethernet uPIM 6-Port Gigabit JXU-6GE-SFP-S Ethernet uPIM 8-Port Gigabit JXU-8GE-TX-S Ethernet uPIM 16-Port Gigabit JXU-16GE-TX-S Ethernet uPIM 1-Port Copper JXE-1GE-TX-S Gigabit Ethernet ePIM 1-Port SFP Gigabit JXE-1GE-SFP-S Ethernet ePIM Dual-Port Serial...
Page 136
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 57: J-series PIM Power Consumption and Heat Dissipation (continued) Name Model Number ADSL 2/2+ JX-1ADSL-B-S Annex B PIM (1 port, for ISDN) G.SHDSL PIM JX-2SHDSL-S (2-port two-wire mode or 1-port four-wire mode) TGM550 Avaya...
Network Cable Specifications The Services Router supports interfaces that use various kinds of network cable. For information about the type of cable used by each interface, see “Network Cable Specifications and Connector Pinouts” on page 223. ISDN Provisioning You might need a network termination type 1 (NT1) device to connect your ISDN interface to the ISDN service.
Page 138
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Site Preparation Checklist...
Chapter 6 Installing and Connecting a Services Router Make the appropriate preparations and verify the J-series equipment before installing a J-series Services Router and connecting it to a power source and the network. CAUTION: Do not install a combination of PIMs in a single chassis that exceeds the maximum power and heat capacity of the chassis.
Page 140
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide For J4350 and J6350 Services Routers—Mounting brackets and screws (provided), number 2 Phillips screwdriver, and mounting screws appropriate for your rack. To connect the router to power and ground, have ready a grounding cable and lug, as specified in “Chassis Grounding”...
Page 141
Installing J2320 and J2350 Routers WARNING: DC-powered Services Routers are intended for installation only in a restricted access location. You can center-mount or front-mount the J2320 and J2350 Services Routers in a rack. In general, a center-mount rack is preferable to a front-mount rack because the more even distribution of weight in the center-mount rack provides greater stability.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Align the top hole in each mounting bracket with a hole in each rack rail as shown in Figure 56 on page 120 and Figure 57 on page 120, making sure the chassis is level.
Page 143
You can center-mount or front-mount the J4350 and J6350 Services Routers in a rack. In general, a center-mount rack is preferable to a front-mount rack because the more even distribution of weight in the center-mount rack provides greater stability. Many types of racks are acceptable, including four-post (telco) racks, enclosed cabinets, and open-frame racks.
Page 144
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Figure 59: Attaching Center Screw to the Rack Lift the router and insert the larger elliptical openings in the mounting brackets onto the partially inserted screws so that the router is hanging from the two screws (see Figure 60 on page 122).
Figure 61: Completing the Installation Connecting Interface Cables to Services Routers You connect the interfaces installed in the Services Router to various network media. For more information about the network interfaces supported on the router, see the J-series Services Router Basic LAN and WAN Access Configuration Guide. Have ready a length of the type of cable used by the interface, as specified in “Network Cable Specifications and Connector Pinouts”...
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide For J2320 and J2350 Services Routers—The grounding cables must be, at minimum, 14 AWG single-strand wire cable. The grounding lug must be a ring-type, vinyl-insulated TV14-8R lug as shown in Figure 62 on page 125 and Figure 63 on page 126.
Page 147
With a Phillips screwdriver, remove the screw and washer from the PEM nuts at the grounding point on the rear of the chassis. Place the grounding lug at the other end of the cable over the grounding point, as shown in Figure 62 on page 125 through Figure 64 on page 126. Secure the cable lug to the grounding point, first with the washer, then with the screw.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Figure 63: Connecting AC Power to the J2350 Services Router Figure 64: Connecting AC Power to the J4350 or J6350 Services Router Connecting DC Power CAUTION: If your J6350 Services Router includes an optional redundant DC power supply, connect each of the two power supplies to different input power sources.
Page 149
Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to the ESD point on the chassis. For more information about ESD, see “Preventing Electrostatic Discharge Damage” on page 251. Use a grounding cable to connect the router to earth ground: (For cable requirements, see “Chassis Grounding”...
Page 150
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide overtighten. Apply between 8 lb-in. (0.9 Nm) and 9 lb-in. (1.02 Nm) of torque to the screw. Using the other removed screw, secure the negative (–) DC source power cable lug to the overtighten.
Figure 66: Connecting DC Power to the J4350 or J6350 Services Router Powering a Services Router On and Off To power on a Services Router, press the power button. The Routing Engine boots as the power supply completes its startup sequence. The startup and remains on steadily when the router is operating normally.
Page 152
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Powering a Services Router On and Off...
Chapter 7 Establishing Basic Connectivity The JUNOS software is preinstalled on the Services Router. When the router is powered on, it is ready to be configured. If the router does not have a configuration from the factory or your service provider, you must configure the software to establish basic connectivity.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 60: Basic Connectivity Terms (continued) Term gateway hostname loopback address Network Time Protocol (NTP) root user secure shell (SSH) Telnet Basic Connectivity Overview To connect your Services Router to the network and establish basic connectivity, you enter information about your network.
Page 155
Root Password The root user has complete privileges to configure the Services Router, and manage files in the router's file system. Initially, the root password is not defined on the router. To ensure basic security, you must define the root password during initial configuration.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide are added to the configuration to resolve hostnames in the order in which you list them. If you plan to include your router in several domains, you can add these domains to the configuration so that they are included in a DNS search.
After the initial configuration is complete, you can attach the built-in Ethernet port that you are using for management purposes to the management network. Before initial configuration, when the factory default configuration is active, the router attempts to perform autoinstallation by obtaining a router configuration through all its connected interfaces, including client out the built-in Ethernet interfaces.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide If the router is operating in a Common Criteria environment, see the Secure Configuration Guide for Common Criteria and JUNOS-FIPS. SSH also allows you to connect to the router and access the CLI to execute commands from a remote system.
A management device, such as a PC or laptop, with a serial port and an asynchronous terminal application (such as Microsoft Windows Hyperterminal) An RJ-45 to DB-9 serial port adapter (provided) An Ethernet cable (provided) For a remote connection, two dial-up modems For a remote modem connection, a DB-9 female to DB-25 male adapter, or other adapter appropriate for your modem (not provided) Connecting to a Services Router...
Page 160
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Turn on the power to the management device. The router assigns an IP address to the management device within the is configured to use DHCP. From the management device, open a Web browser and enter the IP address 192.168.1.1 Configure basic settings for your router as described in “Configuring Basic Settings with J-Web Quick Configuration”...
Page 161
Figure 68: Connecting to the Gigabit Ethernet Port on J4350 and J6350 Routers Connecting to the CLI Locally If you plan to use the CLI to configure the router, you must connect through the console port, as shown in Figure 69 on page 140 and Figure 70 on page 141. NOTE: Figure 69 on page 140 and Figure 70 on page 141 show a connection to a local management device.
Page 162
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Configure the port settings as follows: Bits per second: 9600 Data bits: 8 Parity: None Stop bits: 1 Flow control: None Power on the router by pressing the power button on the front panel. Verify that POWER The terminal emulation screen on your management device displays the boot sequence.
Figure 70: Connecting to the Console Port on J4350 and J6350 Routers Connecting to the CLI Remotely You can connect to the CLI from a remote location through two dial-up modems: a modem that is connected to the console port on the Services Router and a second modem connected to a remote management device.
Page 164
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide From the PC or laptop computer, start your asynchronous terminal emulation application (such as Microsoft Windows Hyperterminal) and select the to which the modem is connected (for example, Configure the port settings as follows: Bits per second: 9600 Data bits: 8 Parity: None...
Connecting to the CLI at the User End To remotely connect to the CLI through a dial-up modem connected to the console port on the router: At your remote location, connect a modem to a management device such as a PC or laptop computer.
Page 166
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Figure 71: Set Up Quick Configuration Page Before you configure the router, gather the information described in “Before You Begin” on page 136. To configure basic settings with J-Web Quick Configuration: If you have not already done so, connect a management device to the interface on port 0/0.
Page 167
To cancel your entries and return to the Quick Configuration page, click Cancel. NOTE: After initial configuration is complete, the Services Router stops functioning as a DHCP server. If you change the IP address of device configured to use DHCP, you lose your DHCP lease and your connection to the router through the J-Web interface.
Page 168
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 61: Set Up Quick Configuration Summary (continued) Field Function Current System Time Synchronizes the system time with the NTP server, or manually set the system time and date. Network DNS Name Servers Specify a DNS server that the router can use to resolve hostnames into addresses.
Configuring Basic Settings with a Configuration Editor To establish basic connectivity on a Services Router, you identify the router, connect the router to the network, and specify basic network settings. In a typical network, the Services Router has the basic settings listed in Table 62 on page 147.
Page 170
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide If you are using the J-Web interface, click Commit to view a summary of your changes, then click OK to commit the configuration. If you are using the CLI, commit the configuration by entering the To check the configuration, see Displaying Basic Connectivity Configurations on page 150.
Page 171
Table 63: Configuring Basic Settings (continued) Task J-Web Configuration Editor Define the NTP server that In the Nested configuration section, next to Ntp, click NTP requests can be sent Configure or Edit. Next to Server, click Add New Entry. In the Address box, type the NTP server's IP address—for example, Click OK.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 63: Configuring Basic Settings (continued) Task J-Web Configuration Editor Define the IP address for In the configuration editor hierarchy, next to Interfaces, click Configure or Edit. ge-0/0/0 In the Interface table, locate the Unit.
Page 173
services { ntp { server 10.148.2.21; interfaces { ge-0/0/0 { unit 0 { family inet { address 192.168.1.1/24; lo0 { unit 0 { family inet { address 172.16.1.24/32; The output shows the configuration of basic connectivity. Verify that the values Meaning displayed are correct for your Services Router.
Page 174
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Displaying Basic Connectivity Configurations...
Chapter 8 Configuring Secure Web Access You can manage a Services Router remotely through the J-Web interface. To communicate with the router, the J-Web interface uses Hypertext Transfer Protocol (HTTP). HTTP allows easy Web access but no encryption. The data that is transmitted between the Web browser and the router by means of HTTP is vulnerable to interception and attack.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 64: Secure Web Access Terms (continued) Term Definition Hypertext Transfer Protocol similar to HTTP with an added encryption layer that encrypts and decrypts Protocol over Secure user page requests and pages that are returned by a Web server. HTTPS is used for Sockets Layer (HTTPS) secure communication, such as payment transactions.
Obtain an SSL certificate from a trusted signing authority. See “Generating SSL Certificates” on page 155. Generating SSL Certificates To enable secure Web access, you must first generate a digital SSL certificate, and then enable HTTPS access on the Services Router. To generate an SSL certificate: Enter the following interface.
Page 178
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Figure 72: Quick Configuration Secure Access Page To configure Web access settings in the J-Web interface: Enter information into the Secure Access Quick Configuration page, as described in Table 65 on page 157. Click one of the following buttons: To apply the configuration and stay on the Quick Configuration page, click Apply.
Page 179
To verify that Web access is enabled correctly, connect to the router using one of the following methods: For HTTP access—In your Web browser, type For HTTPS access—In your Web browser, type address For SSL JUNOScript access—A JUNOScript client such as JUNOScope is required.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 65: Secure Access Quick Configuration Summary (continued) Field Function Enable HTTPS on All Enables HTTPS on all interfaces at one Interfaces time. HTTPS-Enabled Allows you to specify interfaces on which Interfaces you want to enable HTTPS access.
Table 66: Configuring a Secure Web Access (continued) Task J-Web Configuration Editor Import the SSL certificate Next to Certificates, click Configure. that you have Next to Local, click Add new entry. generated—for example, In the Name box, type a name for the certificate to be imported—for example, For information about generating SSL certificates,...
Page 182
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide local { new { "-----BEGIN RSA PRIVATE KEY-----\nMIICXQIBAAKBgQC/C5UI4frNqbi The output shows the intended secure access configuration. Meaning For more information about the format of a configuration file, see the J-series Services Related Topics Router Basic LAN and WAN Access Configuration Guide.
Chapter 9 Installing and Managing J-series Licenses To enable some JUNOS software features on a J-series Services Router, you must purchase, install, and manage separate software licenses. The presence on the router of the appropriate software license keys (passwords) determines the features you can configure and use.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide message after it commits the configuration rather than failing to commit it because of a license violation. Software Feature Licenses Each feature license is tied to exactly one software feature, and that license is valid for exactly one Services Router.
Managing J-series Licenses with the J-Web Interface To manage licenses with the J-Web interface, you perform the following tasks: Adding New Licenses with the J-Web Interface on page 164 Deleting Licenses with the J-Web Interface on page 164 Displaying License Keys with the J-Web Interface on page 164 Downloading Licenses with the J-Web Interface on page 164 The Licenses page displays a summary of licensed features that are configured on the Services Router and a list of licenses that are installed on the routers.
Page 186
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Adding New Licenses with the J-Web Interface To add a new license key on a Services Router with the J-Web license manager: In the J-Web interface, select Manage>Licenses. Under Installed Licenses, click Add to add a new license key. Do one of the following, using a blank line to separate multiple license keys: In the License File URL box, type the full URL to the destination file containing the license key to be added.
Select Save it to disk and specify the file to which the license keys are to be written. Go on to “Verifying J-series License Management” on page 166. Managing J-series Licenses with the CLI To manage the J-series licenses with the CLI, perform the following tasks. Adding New Licenses with the CLI on page 165 Deleting a License with the CLI on page 165 Saving License Keys with the CLI on page 166...
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Saving License Keys with the CLI To save the licenses installed on the Services Router to a file with the CLI: Enter operational mode in the CLI. To save the installed license keys to a file or URL, enter the following command: request system license save filename | url For example, the following command saves the installed license keys to a file named...
Page 189
Each license is present. Licenses are listed in ascending alphanumeric order by license ID. The feature for each license is the expected feature. The features enabled are listed by license. An all-inclusive license has All configured features have the required licenses installed. The column must show that no licenses are required.
Page 190
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide G03000002224 aeaqea qkjjhd ambrha 3tkqkc ayargb zicik6 G03000002225 aeaqea qkjjhd ambrha 3tkqkc ayarab zicik6 The output shows a list of the license keys installed on the Services Router. Verify Meaning that each expected license key is present.
Chapter 10 Replacing Hardware Components Because many of the Services Router's hardware components are field-replaceable units (FRUs), you can remove and replace them yourself. When you need to replace a router component, contact your customer support or sales representative to order the field-replaceable unit (FRU) that contains the component.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 69: Tools and Parts Required Tool or Part Electrostatic bag or antistatic mat Electrostatic discharge (ESD) grounding wrist strap Flat-blade screw-blade screwdriver, approximately 1/4 in. (6 mm) Phillips (+) screwdriver, number 1 and number 2 Replacing the Console Port Cable The RJ-45 port labeled...
Page 195
CAUTION: Do not hot-swap PIMs. Failure to power off the router before removing or installing a PIM might result in damage to the hardware. Figure 73: Removing a PIM To remove a PIM (see Figure 73 on page 173): Place an electrostatic bag or antistatic mat on a flat, stable surface to receive the PIM.
Page 196
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Installing a PIM CAUTION: Do not hot-swap PIMs. Failure to power off the router before removing or installing a PIM might result in damage to the hardware. Figure 74: Installing a PIM CAUTION: Do not install a combination of PIMs in a single chassis that exceeds the maximum power and heat capacity of the chassis.
If necessary, arrange the cables to prevent them from dislodging or developing stress points: Secure each cable so that it is not supporting its own weight as it hangs to the floor. Place excess cable out of the way in a neatly coiled loop. Use fasteners to maintain the shape of cable loops.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Arrange the cable as necessary to prevent it from dislodging or developing stress points: Secure the cable so that it is not supporting its own weight as it hangs to the floor.
Page 199
With a Phillips screwdriver remove the flat head screws from the rear and sides of the chassis. Position the router so that you face the front panel. Place your hands on the cover and press down while pushing the cover back until the two front tabs disengage from the chassis base (see Figure 75 on page 177).
For information about configuring the internal compact flash, see the J-series Services Router Administration Guide. NOTE: Use only compact flash cards purchased from Juniper Networks for your J-series platform and model. Replacing Internal Compact Flashes on J2320 and J2350 Routers...
Page 201
Figure 78: Location of J2320 and J2350 Internal Compact Flash To replace the internal compact flash: Place an electrostatic bag or antistatic mat on a flat, stable surface. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to the ESD point on the chassis, or to an outside ESD point if the router is disconnected from earth ground.
Page 202
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Figure 79: Removing the J2320 or J2350 Internal Compact Flash Place the compact flash on the antistatic mat or in the electrostatic bag. With the vendor name and memory size facing up and the arrow pointing towards the router, insert the new compact flash into the compact flash slot (see Figure 80 on page 180).
The internal compact flash is installed in a slot on the bottom of the J4350 or J6350 chassis (see Figure 81 on page 181). NOTE: Use only compact flash cards purchased from Juniper Networks for your J-series platform and model.
Page 204
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Figure 82: Alternative Horizontal Orientation of J4350 and J6350 Compact Flash To replace the compact flash: Place an electrostatic bag or antistatic mat on a flat, stable surface. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to the ESD point on the chassis, or to an outside ESD point if the router is disconnected from earth ground.
Page 205
Figure 83: Removing the J4350 or J6350 Compact Flash Place the compact flash on the antistatic mat or in the electrostatic bag. Slide the new compact flash into the slot and press down, as shown in Figure 84 on page 183. Figure 84: Inserting the J4350 or J6350 Compact Flash NOTE: On some Services Routers the compact flash is in a horizontal position.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Replace the power cord or cable. Press and release the power button to power on the router. Verify that the LED lights steadily. Replacing External Compact Flashes The external compact flash is an optional component on J2320 and J2350 Services Routers.
Page 207
Skip this step, if the router did not boot from the external compact flash (see step 1). With a Phillips screwdriver, loosen the pan head screws that secure the external compact flash cover to the rear of the chassis (see Figure 85 on page 185). Figure 85: Removing the External Compact Flash Cover Remove the compact flash cover.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Tighten the pan head screws that secures the compact flash slot cover to the rear of the chassis. Plug the power cord into the power supply. Press and release the power button to power on the router. Verify that the LED lights steadily.
Page 209
Verify the device that the router used to boot, by running the command from the CLI. For example: user@host> show system storage Filesystem /dev/ad0s1a The boot device is mounted on The external compact flash is located at flash. If the external compact flash, you need to power off the router before replacing the compact flash.
DRAM modules. Installing DRAM modules in slots away from each other provides better performance than installing them in two adjacent slots. NOTE: Use only DRAM modules purchased through Juniper Networks specifically for your model. Figure 88: J2320 and J2350 DRAM Location...
Figure 89: J4350 and J6350 DRAM Location To modify the DRAM configuration, use the following procedures: Removing a DRAM Module on page 189 Installing a DRAM Module on page 190 Removing a DRAM Module To remove a DRAM module: Place an electrostatic bag or antistatic mat on a flat, stable surface. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to the ESD point on the chassis, or to an outside ESD point if the router is disconnected from earth ground.
Page 212
Installing a DRAM Module J2320, J2350, J4350 and J6350 Services Routers support 256-MB and 512-MB DRAM modules. Use only DRAM modules purchased from Juniper Networks specifically for your model. NOTE: If you are installing a second DRAM module, do not install it in a slot adjacent to the first module.
Pressing firmly on both ends, push the module into the slot until the ejectors click into the closed position (see Figure 90 on page 190). Slide the cover onto the chassis. Replace and tighten the screws on the sides and top of the chassis that secure the cover to the chassis.
Page 214
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Locate a replacement power cord with the type of plug appropriate for your geographical location (see “AC Power, Connection, and Power Cord Specifications” on page 109). Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to the ESD point on the chassis, or to an outside ESD point if the router is disconnected from earth ground.
Page 215
NOTE: If the power supply is a redundant power supply in a J6350 Service Router, you can leave the router powered on and power flowing in the other power supply. Unplug the power cord from the power source receptacle. Unplug the power cord from the appliance inlet on the power supply faceplate. Slide the ejector tab on the power supply faceplate to the right and hold it in place to unlock the power supply.
Page 216
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide NOTE: Each power supply must be connected to a dedicated AC power feed. For information about connecting to AC power sources, see “Connecting Power” on page 124. Verify that the power cord does not block access to router components or drape where people might trip on it.
Page 217
CAUTION: You must ensure that power connections maintain the proper polarity. The power source cables might be labeled is no standard color coding for DC power cables. The color coding used by the external DC power source at your site determines the color coding for the leads on the power cables that attach to the terminal studs on each power supply.
Page 218
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide CAUTION: You must ensure that power connections maintain the proper polarity. The power source cables might be labeled is no standard color coding for DC power cables. The color coding used by the external DC power source at your site determines the color coding for the leads on the power cables that attach to the terminal studs on each power supply.
Page 219
Ensure that the voltage across the DC power source cable leads is 0 V and that the cable leads cannot become active during installation. CAUTION: You must ensure that power connections maintain the proper polarity. The power source cables might be labeled is no standard color coding for DC power cables.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Figure 94: Installing a DC Power Supply Replacing Crypto Accelerator Modules on J2320 and J2350 Routers The Crypto Accelerator Module is a processor card that enhances performance of cryptographic algorithms used in IP security (IPSec) services. The Crypto Module is an optional feature on J2320 and J2350 Services Routers.
Page 221
Removing a J2320 or J2350 Crypto Accelerator Module NOTE: If you are installing a Crypto Accelerator Module into a J2320 or J2350 Services Router for the first time, proceed directly to “Installing a J2320 or J2350 Crypto Accelerator Module” on page 200. To remove the Crypto Accelerator Module: Place an electrostatic bag or antistatic mat on a flat stable surface to receive the Crypto Module.
Page 222
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Installing a J2320 or J2350 Crypto Accelerator Module To install a Crypto Accelerator Module: Take the following steps if you have not already done so: Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to the ESD point on the chassis, or to an outside ESD point if the router is disconnected from earth ground.
Press and release the power button to power on the router. Verify that the LED lights steadily. Verify that the Crypto Module is correctly installed by issuing the hardware user@host> show chassis hardware user@host> show chassis hardware Hardware inventory: Item Chassis Midplane System IO...
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Figure 98: Crypto Accelerator Module Location on J4350 and J6350 Routers To modify a Crypto Accelerator Module configuration, use the following procedures: Removing a J4350 or J6350 Crypto Accelerator Module on page 202 Installing a J4350 or j6350 Crypto Accelerator Module on page 204 Removing a J4350 or J6350 Crypto Accelerator Module NOTE: If you are installing a Crypto Accelerator Module into a J4350 Services Router...
Page 225
Locate the Crypto Module on the system board (see Figure 98 on page 202). Using a Phillips screwdriver remove the screw, as shown in Figure 99 on page 203. Figure 99: Removing a J4350 or J6350 Crypto Module Screw Pull the white release clips on either side of the Crypto Module out to either side, as shown in Figure 100 on page 203, to tilt the Crypto Module upward.
Page 226
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Installing a J4350 or j6350 Crypto Accelerator Module To install a Crypto Accelerator Module: Take the following steps if you have not already done so: Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to the ESD point on the chassis, or to an outside ESD point if the router is disconnected from earth ground.
Crypto Module correctly. Replacing Air Filters on J2350 Routers The cooling fans on J2350 routers draw air through vents along the left side of the chassis and exhaust it through vents on the right side of the chassis. For more information, see “J2320 and J2350 Cooling System”...
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Figure 102: Placing the Air Filter on the Air Filter Tray Press down on the filter until it is firmly seated against the bottom of the tray. Hold the filter tray with the thumbscrew so that its sheet metal side faces the power supply fan exhaust.
Page 229
Figure 104: Attaching Air Filter and Filter Cover We recommend changing the filter every 6 months. However, the optimal filter replacement interval can vary depending on the environment where the router is located. If temperature alarms appear, inspect the air filter. To replace the air filter: Remove the filter cover by squeezing the plastic tabs on either side of the filter cover.
Page 230
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Replacing Air Filters on J4350 and J6350 Routers...
This chapter contains the following topics: Chassis Alarm Conditions on page 209 Troubleshooting Power Management on page 210 Contacting the Juniper Networks Technical Assistance Center on page 212 Chassis Alarm Conditions You can monitor alarms to troubleshoot hardware problems on a Services Router.
Page 232
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 70: Chassis Alarm Conditions and Corrective Actions (continued) Component Alarm Conditions A PIM has failed. When a PIM fails, it attempts to reboot. If the Routing Engine detects that a PIM is rebooting too often, it shuts down the PIM.
Page 233
To bring the PIM online: Check if the PIM exceeds the power and heat tokens permitted by issuing the show chassis fpc show chassis power-ratings user@host> show chassis fpc Temp CPU Utilization (%) Slot State 0 Online -------------------- CPU less FPC -------------------- 1 Empty --------------------- Not Usable --------------------- 2 Online...
Page 234
JUNOS System Basics Configuration Guide. Contacting the Juniper Networks Technical Assistance Center If you need assistance while troubleshooting a Services Router, open a support case using the Case Manager link at (within the United States) or 1-408-745-9500 (from outside the United States). For more information, see “Contacting Customer Support and Returning...
Contacting Customer Support and Returning Hardware This chapter describes how to return the Services Router or individual components to Juniper Networks for repair or replacement. It contains the following topics: Locating Component Serial Numbers on page 213 Contacting Customer Support on page 216...
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide The following sections describe the label location on each type of component: J2320 and J2350 Chassis Serial Number and Agency Labels on page 214 J4350 and J6350 Chassis Serial Number and Agency Labels on page 215 PIM Serial Number Label on page 216 Power Supply Serial Number Labels on page 216 J2320 and J2350 Chassis Serial Number and Agency Labels...
Page 237
Chapter 12: Contacting Customer Support and Returning Hardware J4350 and J6350 Chassis Serial Number and Agency Labels J4350 and J6350 Services Routers have serial number ID labels on the back of the chassis, as shown in Figure 107 on page 215, and an agency label on the bottom front corner, as shown in Figure 108 on page 215.
Contacting Customer Support After you have located the serial numbers of the components you need to return, contact Juniper Networks Technical Assistance Center (JTAC) in one of the following ways. You can contact JTAC 24 hours a day, seven days a week.
NOTE: Do not return any component to Juniper Networks unless you have first obtained an RMA number. Juniper Networks reserves the right to refuse shipments that do not have an RMA. Refused shipments are returned to the customer via collect freight.
Page 240
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Flat-blade screwdriver, approximately 1/4 in. (6 mm) Phillips (+) screwdrivers, numbers 1 and 2 Packing the Services Router for Shipment To pack the router for shipment, follow this procedure: Retrieve the shipping carton and packing materials in which the router was originally shipped.
Page 241
Chapter 12: Contacting Customer Support and Returning Hardware When you return components, make sure they are adequately protected with packing materials and packed so that the pieces are prevented from moving around inside the carton. Use the original shipping materials if they are available. Place individual boards in electrostatic bags.
Page 242
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Packing a Router or Component for Shipment...
Page 243
Part 4 J-series Requirements and Specifications Network Cable Specifications and Connector Pinouts on page 223 Safety and Regulatory Compliance Information on page 247 J-series Requirements and Specifications...
Page 244
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide J-series Requirements and Specifications...
Chapter 13 Network Cable Specifications and Connector Pinouts The network interfaces supported on the router accept different kinds of network cable. Serial PIM Cable Specifications on page 223 Fast Ethernet RJ-45 Connector Pinout on page 233 Gigabit Ethernet uPIM RJ-45 Connector Pinout on page 233 Gigabit Ethernet ePIM RJ-45 Connector Pinout on page 234 Chassis Console Port Pinouts on page 234 E1 and T1 RJ-48 Cable Pinouts on page 235...
Table 81: X.21 DCE Cable Pinout (continued) LFH-60 Pin DB-15 Pin 30 to 29 – Fast Ethernet RJ-45 Connector Pinout Table 82 on page 233 describes the Fast Ethernet RJ-45 connector pinout information. NOTE: Either a straight-through or cross-over cable can be used to connect to the interface.
Table 85: RJ-45 Chassis Console Connector Pinout Table 86 on page 235 describes the DB-9 connector pinouts. Table 86: DB-9 Console Connector Pinout Signal Ground RING E1 and T1 RJ-48 Cable Pinouts The E1 and T1 PIMs use an RJ-48 cable, which is not supplied with the PIM. CAUTION: To maintain agency approvals, use only a properly constructed, shielded cable.
Page 258
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 87 on page 236 through Table 90 on page 237 describe the RJ-48 connector pinouts. Table 87: RJ-48 Connector to RJ-48 Connector (Straight) Pinout RJ-48 Pin (on T1/E1 PIM) (Data Numbering Form) Table 88: RJ-48 Connector to RJ-48 Connector (Crossover) Pinout RJ-48 Pin (on T1/E1 PIM)
Page 259
Table 89: RJ-48 Connector to DB-15 Connector (Straight) Pinout DB-15 Pin RJ-48 Pin (on T1/E1 PIM) (Data Numbering (Data Numbering Form) Form) No connect No connect No connect No connect No connect No connect No connect No connect No connect Table 90: RJ-48 Connector to DB-15 Connector (Crossover) Pinout DB-15 Pin RJ-48 Pin (on T1/E1 PIM)
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 90: RJ-48 Connector to DB-15 Connector (Crossover) Pinout (continued) RJ-48 Pin (on T1/E1 PIM) (Data Numbering Form) E3 and T3 BNC Connector Pinout The E3 and T3 PIMs each use two BNC connectors—one for transmitting data ( and one for receiving data ( ADSL and G.SHDSL RJ-11 Connector Pinout The 1-port ADSL 2/2+ Annex A and Annex B PIMs use an RJ-11 cable, which is not...
ISDN RJ-45 Connector Pinout The 1-port and 4-port ISDN PIMs use an RJ-45 cable, which is not supplied with the PIMs. Table 92 on page 239 describes the RJ-45 connector pinout. Table 92: ISDN RJ-45 Connector Pinout Connector Pinouts for Avaya VoIP Modules The Avaya VoIP modules supported on the Services Router accept different kinds of network cables.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide NOTE: Two different RJ-45 cables and RJ-45 to DB-9 adapters are provided. Do not use the RJ-45 cable and adapter for the Services Router console port to connect to the TGM550 console port. To connect the console port to an external management device, you need an RJ-45 to DB-9 serial port adapter, which is also supplied with the TGM550.
TIM508 Connector Pinout The TIM508 Analog Telephony Interface Module uses a B25A unshielded 25–pair amphenol cable. Table 95 on page 241 describes the TIM508 connector pinout. Table 95: TIM508 Connector Pinout Signal R - Receive Ring Ring Ring Ring Ring Ring Ring TIM510 RJ-45 Connector Pinout...
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 96: TIM510 RJ-45 Connector Pinout (continued) Signal No connection R1 - Transmit T1 - Transmit No connection No connection No connection TIM514 Connector Pinout The TIM514 Telephony Interface Module uses an RJ-11 cable. Table 97 on page 242 describes the TIM514 RJ-11 connector pinout information.
Page 265
Table 98: TIM516 Connector Pinout (continued) Signal Ring Ring Ring Ring Ring Ring Ring Ring Ring Ring Ring Ring Ring Ring Chapter 13: Network Cable Specifications and Connector Pinouts Connector Pinouts for Avaya VoIP Modules...
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Table 98: TIM516 Connector Pinout (continued) Signal Ring Ring TIM518 Connector Pinout The TIM518 Analog Telephony Interface Module uses a B25A unshielded 25–pair amphenol cable. Table 99 on page 244 describes the TIM518 connector pinout. Table 99: TIM518 Connector Pinout Signal Ring...
Chapter 14 Safety and Regulatory Compliance Information To install and use the Services Router safely, follow proper safety procedures. This chapter discusses the following safety and regulatory compliance information: Definition of Safety Warning Levels on page 247 Safety Guidelines and Warnings on page 249 Agency Approvals on page 282 Compliance Statements for Environmental Requirements on page 283 Compliance Statements for NEBS on page 283...
Page 270
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide risico's en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. WARNING: Varoitus Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää...
entraña la corriente eléctrica y familiarizarse con los procedimientos estándar de prevención de accidentes. WARNING: Varning! Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanligt förfarande för att förebygga skador.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide The separate protective earthing terminal provided on this product shall be permanently connected to earth. Replace fuses only with fuses of the same type and rating. Do not open or remove chassis covers or sheet metal parts unless instructions are provided in this manual.
Varning! Denna utrustning ska endast installeras och bytas ut av utbildad och kvalificerad personal. Preventing Electrostatic Discharge Damage Many Services Router hardware components are sensitive to damage from static electricity. Some components can be impaired by voltages as low as 30 V. You can easily generate potentially damaging static voltages whenever you handle plastic or foam packing material or if you move components across plastic or carpets.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Electrical Safety Guidelines and Warnings When working on equipment powered by electricity, follow the guidelines described in the following sections: General Electrical Safety Guidelines on page 252 AC Power Electrical Safety Guidelines on page 253 DC Power Electrical Safety Guidelines on page 254 Power Sources for Redundant Power Supplies on page 255 DC Power Disconnection Warning on page 255...
Install the Services Router in compliance with the following local, national, or international electrical codes: United States—National Fire Protection Association (NFPA 70), United States National Electrical Code. Canada—Canadian Electrical Code, Part 1, CSA C22.1. Other countries—International Electromechanical Commission (IEC) 60364, Part 1 through Part 7.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide The cores in the mains lead are colored in accordance with the following code (within the United States): Green and yellow—Earth Blue—Neutral Brown—Live When a router is equipped with two AC power supplies, both power cords (one for each power supply) must be unplugged to completely disconnect power to the router.
NOTE: Primary overcurrent protection is provided by the building circuit breaker. This breaker should protect against excess currents, short circuits, and earth faults in accordance with NEC ANSI/NFPA70. Ensure that the polarity of the DC input wiring is correct. Under certain conditions, connections with reversed polarity might trip the primary circuit breaker or damage the equipment.
Page 278
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide huolehtivassa kojetaulussa sijaitseva suojakytkin, käännä suojakytkin KATKAISTU-asentoon ja teippaa suojakytkimen varsi niin, että se pysyy KATKAISTU-asennossa. WARNING: Attention Avant de pratiquer l'une quelconque des procédures ci-dessous, vérifier que le circuit en courant continu n'est plus sous tension. Pour en être sûr, localiser le disjoncteur situé...
Chapter 14: Safety and Regulatory Compliance Information DC Power Grounding Requirements and Warning An insulated grounding conductor that is identical in size to the grounded and ungrounded branch circuit supply conductors, but is identifiable by green and yellow stripes, is installed as part of the branch circuit that supplies the unit. The grounding conductor must be permanently connected to earth.
Page 280
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide WARNING: Waarschuwing De juiste bedradingsvolgorde verbonden is aarde naar aarde, +RTN naar +RTN, en –48 V naar – 48 V. De juiste bedradingsvolgorde losgemaakt is en –48 V naar – 48 V, +RTN naar +RTN, aarde naar aarde. WARNING: Varoitus Oikea yhdistettava kytkentajarjestys on maajohto maajohtoon, +RTN varten +RTN, –48 V varten –...
Chapter 14: Safety and Regulatory Compliance Information conectar siempre primero y desconectar por último. Observe que el alambre de tierra se debe conectar siempre primero y desconectar por último. WARNING: ¡Atención! Wire a fonte de alimentação de DC Usando os talões apropriados na extremidade da fiação.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide WARNING: Warnung Wenn Litzenverdrahtung erforderlich ist, sind zugelassene Verdrahtungsabschlüsse, z.B. für einen geschlossenen Regelkreis oder gabelförmig, mit nach oben gerichteten Kabelschuhen zu verwenden. Diese Abschlüsse sollten die angemessene Größe für die Drähte haben und sowohl die Isolierung als auch den Leiter festklemmen.
Waarschuwing Deze apparatuur hoort geaard te worden Zorg dat de host-computer tijdens normaal gebruik met aarde is verbonden. Varoitus Tämä laitteisto on tarkoitettu maadoitettavaksi. Varmista, että isäntälaite on yhdistetty maahan normaalikäytön aikana. Attention Cet équipement doit être relié à la terre. S'assurer que l'appareil hôte est relié...
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Multiple Power Supplies Disconnection Warning WARNING: The J6350 Services Router has more than one power supply connection. All connections must be removed completely to remove power from the unit completely. WARNING: Waarschuwing Deze J6350 eenheid heeft meer dan één stroomtoevoerverbinding;...
Chapter 14: Safety and Regulatory Compliance Information WARNING: Varning! Denna J6350 enhet har mer än en strömförsörjningsanslutning; alla anslutningar måste vara helt avlägsnade innan strömtillförseln till enheten är fullständigt bruten. Power Disconnection Warning WARNING: Before working on the router or near power supplies, unplug the power cord from an AC router.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide WARNING: ¡Atención! Antes de manipular el chasis de un equipo o trabajar cerca de una fuente de alimentación, desenchufar el cable de alimentación en los equipos de corriente alterna (CA). WARNING: Varning! Innan du arbetar med ett chassi eller nära strömförsörjningsenheter skall du för växelströmsenheter dra ur nätsladden.
Chapter 14: Safety and Regulatory Compliance Information WARNING: ¡Atención! El equipo está diseñado para trabajar con sistemas de alimentación tipo TN. WARNING: Varning! Enheten är konstruerad för användning tillsammans med elkraftssystem av TN-typ. Telecommunication Line Cord Warning WARNING: To reduce the risk of fire, use only No. 26 AWG or larger UL-listed or CSA-certified telecommunication line cord.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide WARNING: ¡Atención! Para reducir el riesgo de incendios, usar sólo líneas de telecomunicaciones de calibre No. 26 AWG o más gruesas. WARNING: Varning! För att minska brandrisken skall endast Nr. 26 AWG eller större telekommunikationsledning användas.
Warnung Lesen Sie die Installationsanweisungen, bevor Sie das System an die Stromquelle anschließen. WARNING: Avvertenza Consultare le istruzioni di installazione prima di collegare il sistema all'alimentatore. Advarsel Les installasjonsinstruksjonene før systemet kobles til strømkilden. Aviso Leia as instruções de instalação antes de ligar o sistema à sua fonte de energia. ¡Atención! Ver las instrucciones de instalación antes de conectar el sistema a la red de alimentación.
Page 290
Les directives ci-dessous sont destinées à assurer la protection du personnel: Le rack sur lequel est monté le Juniper Networks router doit être fixé à la structure du bâtiment. Si cette unité constitue la seule unité montée en casier, elle doit être placée dans le bas.
Page 291
Le seguenti direttive vengono fornite per garantire la sicurezza personale: Il Juniper Networks router deve essere installato in un telaio, il quale deve essere fissato alla struttura dell'edificio. Questa unità deve venire montata sul fondo del supporto, se si tratta dell'unica unità...
Page 292
Para garantizar su seguridad, proceda según las siguientes instrucciones: El Juniper Networks router debe instalarse en un bastidor fijado a la estructura del edificio. Colocar el equipo en la parte inferior del bastidor, cuando sea la única unidad en el mismo.
Följande riktlinjer ges för att trygga din säkerhet: Juniper Networks router måste installeras i en ställning som är förankrad i byggnadens struktur. Om denna enhet är den enda enheten på ställningen skall den installeras längst ned på...
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Observe the following guidelines and warnings: General Laser Safety Guidelines on page 272 Class 1 Laser Product Warning on page 272 Class 1 LED Product Warning on page 273 Laser Beam Warning on page 273 Radiation from Open Port Apertures Warning on page 274 General Laser Safety Guidelines When working around PIMs, observe the following safety guidelines to prevent eye...
Page 295
Chapter 14: Safety and Regulatory Compliance Information Class 1 LED Product Warning WARNING: Class 1 LED product. Waarschuwing Klasse 1 LED-product. Varoitus Luokan 1 valodiodituote. Attention Alarme de produit LED Class I. Warnung Class 1 LED-Produktwarnung. WARNING: Avvertenza Avvertenza prodotto LED di Classe 1. Advarsel LED-produkt i klasse 1.
Page 296
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide WARNING: Warnung Nicht direkt in den Strahl blicken und ihn nicht direkt mit optischen Geräten prüfen. WARNING: Avvertenza Non fissare il raggio con gli occhi né usare strumenti ottici per osservarlo direttamente. WARNING: Advarsel Stirr eller se ikke direkte p strlen med optiske instrumenter.
WARNING: Attention Des radiations invisibles à l'il nu pouvant traverser l'ouverture du port lorsqu'aucun câble en fibre optique n'y est connecté, il est recommandé de ne pas regarder fixement l'intérieur de ces ouvertures. WARNING: Warnung Aus der Port-Öffnung können unsichtbare Strahlen emittieren, wenn kein Glasfaserkabel angeschlossen ist.
Page 298
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Battery Handling Warning WARNING: Replacing the battery incorrectly might result in an explosion. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. WARNING: Waarschuwing Er is ontploffingsgevaar als de batterij verkeerd vervangen wordt.
Page 299
Chapter 14: Safety and Regulatory Compliance Information WARNING: ¡Atención! Existe peligro de explosión si la batería se reemplaza de manera incorrecta. Reemplazar la batería exclusivamente con el mismo tipo o el equivalente recomendado por el fabricante. Desechar las baterías gastadas según las instrucciones del fabricante.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide WARNING: Avvertenza Prima di intervenire su apparecchiature collegate alle linee di alimentazione, togliersi qualsiasi monile (inclusi anelli, collane, braccialetti ed orologi). Gli oggetti metallici si riscaldano quando sono collegati tra punti di alimentazione e massa: possono causare ustioni gravi oppure il metallo può...
Chapter 14: Safety and Regulatory Compliance Information WARNING: Varoitus Älä työskentele järjestelmän parissa äläkä yhdistä tai irrota kaapeleita ukkosilmalla. WARNING: Attention Ne pas travailler sur le système ni brancher ou débrancher les câbles pendant un orage. WARNING: Warnung Arbeiten Sie nicht am System und schließen Sie keine Kabel an bzw.
Page 302
40 C. Para evitar a restrição à circulação de ar, deixe pelo menos um espaço de 15,2 cm à volta das aberturas de ventilação. WARNING: ¡Atención! Para impedir que un encaminador de la serie Juniper Networks router se recaliente, no lo haga funcionar en un área en la que se supere la...
15,2 cm alrededor de las aperturas para ventilación. WARNING: Varning! Förhindra att en Juniper Networks router överhettas genom att inte använda den i ett område där den maximalt rekommenderade omgivningstemperaturen på 40 C överskrids. Förhindra att luftcirkulationen inskränks genom att se till att det finns fritt utrymme på...
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide WARNING: Aviso A descartagem final deste produto deverá ser efectuada de acordo com os regulamentos e a legislação nacional. WARNING: ¡Atención! El desecho final de este producto debe realizarse según todas las leyes y regulaciones nacionales WARNING: Varning! Slutlig kassering av denna produkt bör skötas i enlighet med landets alla lagar och föreskrifter.
EN 61000-3-2 Power Line Harmonics EN 61000-3-3 Voltage Fluctuations and Flicker EN 61000-4-2 ESD EN 61000-4-3 Radiated Immunity EN 61000-4-4 EFT EN 61000-4-5 Surge EN 61000-4-6 Low Frequency Common Immunity EN 61000-4-11 Voltage Dips and Sags ETSI ETSI EN-300386-2 Telecommunication Network Equipment. Electromagnetic Compatibility Requirements Compliance Statements for Environmental Requirements Lithium Battery...
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Canada This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements.
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide Japan The preceding translates as follows: This is a Class B product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this product is used near a radio or television receiver in a domestic environment, it may cause radio interference.
United States The Services Router has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Page 310
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide If trouble is experienced with this equipment or for repair or warranty information, please follow the applicable procedures explained in the “Technical Support” section of this manual. FCC Registration Number—See label on product. Required Connector (USOC)—RJ-48C Service Order Code (SOC)—6.ON Compliance Statements for EMC Requirements...
Index Symbols #, comments in configuration statements...xviii #, configuration mode command prompt...93 ( ), in syntax descriptions...xviii * (red asterisk)...86 4-Port Fast Ethernet ePIM...61 4-Port ISDN BRI S/T PIM description...62 PIM ONLINE LED...63 4-Port ISDN BRI U PIM description...62 PIM ONLINE LED...63 <...
Page 314
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide alternative boot media See boot devices; USB altitude requirement...106 analog media module See TIM514 analog telephone (LINE) ports TGM550, pinouts...240 TIM508, possible configurations...73 TIM514, pinouts...242 TIM514, possible configurations...76 TIM516, possible configurations...77 TIM518, possible configurations...78 analog trunk (TRUNK) ports TGM550, pinouts...240...
Page 315
Commit (J-Web configuration editor)...89 OK (J-Web configuration editor)...88 OK (Quick Configuration)...88 power...20, 33 RESET CONFIG...22, 35 cables AC power See AC power cords ADSL RJ-11 pinouts...238 arranging for safety...175 Avaya VoIP 10 AWG replacement grounding cable...66 chassis console port, DB-9 connector pinouts...235 chassis console port, RJ-45 connector pinouts...234...
Page 316
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide command prompts changing...98 configuration mode (#)...93 operational mode (>)...92 command-line interface See CLI configuration editor; JUNOS CLI comments, in configuration statements...xviii Commit button...89 committed configuration root password requirement...133 Common Criteria environments management access affected...136 NTP requirement...133 password limitations...133...
Page 317
daemons See processes, software datasheets URL...43 DB-9 connector pinouts chassis console port...235 TGM550 console port...239 DB-9 to DB-25 serial port adapter...142 DC power cables See DC power cables connecting power...126 dedicated DC power feed requirement...197 electrical specifications...109 grounding requirements and warning...257 grounding the router...127 installing a J6350 power supply...196 J2320 system...24...
Page 318
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide earthquakes rack-mount requirements...105 seismic requirements...106 EIA-530A DCE cable pinouts...229 EIA-530A DTE cable pinouts...228 electrical specifications...109 electricity safety warnings...252 wiring guidelines...108 electromagnetic compatibility (EMC) See EMC electromagnetic interference (EMI) See See EMI electrostatic bag, for storing components...251 electrostatic discharge, preventing...251 elements, J-Web...84...
Page 320
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide immunity standards...282 initial configuration requirements...136 injury, steps to take...261 installation AC power supplies (J6350)...193 air filter...206 compact flash...178, 181 console port cable (chassis)...172 Crypto Accelerator Module...200, 204 DC power supplies (J6350)...196 DRAM modules...190 initial...117 licenses (CLI)...165...
Page 322
USB port...36 Japan, compliance statement...286 JTAC (Juniper Networks Technical Assistance Center) contacting...212 contacting for hardware return...216 information required for hardware return...216 Juniper Networks Technical Assistance Center See JTAC JUNOS CLI CLI terminal...92 command completion...95 command hierarchy...91 command modes...82 command prompts See command prompts connecting locally...139...
Page 323
ALM (TGM550 alarm)...72 ALM (TIM508 alarm)...74 ALM (TIM510 alarm)...75 ALM (TIM514 alarm)...76 ALM (TIM516 alarm)...77 ALM (TIM518 alarm)...79 ALM (TIM521 alarm)...80 ASB (alternate software bank)...72 channelized E1 ports...58 channelized T1 ports...58 Class 1 product warning...273 E1 port status...57 E3 port status...60 ETR (emergency transfer relay)...72 Fast Ethernet port status (4-port ePIM)...62 Fast Ethernet port status (dual-port PIM)...61...
Page 324
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide DC power cable, replacing...194 DRAM modules...188 external compact flash...184 internal compact flash...178, 181 PIM cables...175 PIMs...172 power system...191 tools and parts required...171 USB storage device...186 warnings...275 major (red) alarms PIMs...210 Routing Engine...210 management access...135 management device...
Page 325
PIMs (Physical Interface Modules) 4-Port Fast Ethernet...61 4-Port ISDN BRI...62 ADSL...64 Avaya VoIP modules See Avaya VoIP modules cables and connectors...223 Dual-Port Channelized T1/E1/ISDN PRI PIM...57 Dual-Port E1...56 Dual-Port Fast Ethernet...60 Dual-Port Serial...55 Dual-Port T1...56 E3 ...59 failure...210 field-replaceable PIMs...46 G.SHDSL ...65 Gigabit Ethernet ePIMs...52 Gigabit Ethernet uPIMs...49...
Page 326
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide power AC power See AC power applying...129 button...20, 33 connecting...124 consumption, PIMs...112 DC power See DC power grounding requirement...123 LED...20, 33 managing...112 power cables See DC power cables power cords See AC power cords power supplies See power supplies power system See power system removing...129...
Page 327
tools and parts required...171 USB storage device...186 request chassis pic fpc-slot command...175 request system license add command...165 request system license add terminal command...165 request system license delete command...165 request system license save command...166 required entry ...86 rescue configuration, resetting with RESCUE CONFIG button...22, 35 reset power button for restart...20, 33...
Page 328
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide read installation instructions...266 telecommunications cord...265 TN power system...264 safety standards...282 fire safety...106 sample configuration for basic connectivity...150 for secure access...160 for SSL certificates...159 saving licenses (CLI)...166 screen length, CLI, setting ...98 screen width, CLI, setting ...99 secure access generating SSL certificates...155...
Page 329
show chassis routing-engine command checking CPU temperature...25, 38 checking DRAM amount...18, 31 verifying DRAM installation and configuration...191 show cli command...97 show system license command...166 explanation...166 show system license keys command...167 show system license usage command...167 explanation...167 shutdown graceful...129 immediate...129 temperature See shutdown temperature shutdown temperature NEBS-compliant routers...25, 38 non-NEBS-compliant routers...38...
Page 330
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide system overview hardware...13 software...39 system time defining (Quick Configuration)...146 overview...133 synchronizing (configuration editor)...149 synchronizing (Quick Configuration)...145 T1 ports description...56 See also channelized T1 ports LED states...57 RJ-48 cable pinouts...235 T1 trunk ports, TIM510 description...74 pinouts...241 T1/E1 media module See TIM508 See TIM510 See...
Page 331
trunk ports, TIM508 pinouts...241 TRUNK ports, TIM514...75 trunk ports, TIM516 pinouts...242 trunk ports, TIM518 pinouts...244 TST LED...75 turning on a Services Router...129 TX/RX LED...23, 35, 54 Type C fire extinguishers...107 types of configuration statements...94 U port See ISDN BRI ports United States, compliance statements...287 universal serial bus See USB unpacking the router...118...
Page 332
J2320, J2350, J4350, and J6350 Services Router Getting Started Guide signaling limitations...108 suppressing electromagnetic interference (EMI)...108 working directory, setting...98 X.21 DCE cable pinouts...232 X.21 DTE cable pinouts...231 Index...