1. Manuals
  2. Brands
  3. New Home Manuals
  4. Sewing Machine
  5. 535
  6. Manual instruction

New Home 535 Manual Instruction

Hide thumbs
Table of Contents

Advertisement

Quick Links

Editors notes:
This is a recreated version of an original scan from a "New Home 535" sewing machine.
All artwork is original, however for clarity some of the overlaid lettering has been replaced with clearer versions. No
changes were made to the actual letters and numbers referenced in the document.
I attempted to keep the document as original as possible; however there have been a few minor spelling
corrections.
For a history of New Home and Janome, please see Appendix B.
As I find which parts are compatible with this machine I will update the document. Appendix A contains the list of
the compatible items.
If you have information on this machine that would be a good addition to this document, feel free to email me to
gbestwick@shaw.ca
Gord Bestwick
Also a very important note:
I have created this manual out of a desire to ensure that old serviceable machines get the support that they need. It
was provided to
"Don Tai"
for distribution for free. If you have paid for this version of the manual demand your
money back! This manual should, would, and will always be free of charge!

Advertisement

Table of Contents
loading

Related Manuals for New Home 535

Summary of Contents for New Home 535

  • Page 1 Editors notes: This is a recreated version of an original scan from a “New Home 535” sewing machine. All artwork is original, however for clarity some of the overlaid lettering has been replaced with clearer versions. No changes were made to the actual letters and numbers referenced in the document.

  • Page 2: Sewing Machine

    MANUAL OF INSTRUCTION SEWING MACHINE MODEL 535 (New Home/Imperial/Janome) Version 1.0...
  • Page 3 IMPORTANT The wires in this mains lead are coloured in accordance with the following code: GREEN AND YELLOW – EARTH. BLUE - NEUTRAL. BROWN - LIVE. As the colours of the mains lead of the appliance may not correspond with the coloured markings identifying the terminals in your plug –...

  • Page 4: Table Of Contents

    Contents TO REGULATE LENGTH OF STITCH AND DIRECTION OF FEED ..18 STRAIGHT SEWING AND ZIGZAG SEWING ......... 19 TO REMOVE BOBBIN CASE ............7 MANUAL ZIGZAG PATTERN SEWING .......... 20 TO WIND BOBBIN ................ 7 TO REMOVE WORK ..............20 TO ADJUST BOBBIN WINDING DEVICE ........
  • Page 5 NAMES OF PARTS...

  • Page 6: Names Of Parts

    NAMES OF PARTS 15. Needle plate Spool pin 16. Needle Zigzag width control knob 17. Needle clamp Top cover 18. Thread tension regulator Top cover thread guide and Tension bracket 19. Arm Thread take-up lever 20. Bed plate Patchomatic darner 21.

  • Page 7: To Remove Bobbin Case

    TO REMOVE BOBBIN CASE Turn the balance wheel towards you until the needle bar and take-up lever are both to their highest point. Open the slide plate in the bed of the machine so that the bobbin case can be reached. Insert the thumb and forefinger to open the latch and withdraw the bobbin case.
  • Page 8 2. Place a bobbin on the bobbin winder spindle, revolve the bobbin until the notch in the bobbin meets the spring on the spindle, and push the bobbin down. Then push the bobbin winding spindle so that the latch fits into the bobbin. (Fig. 1) 3.

  • Page 9: To Adjust Bobbin Winding Device

    TO ADJUST BOBBIN WINDING DEVICE The bobbin must be wound evenly. If not, irregular stitching will be the result. When the bobbin is wound excessively on the upper part of the bobbin (A), loosen the top cover thread guide set screw on the front of the top cover and lower the thread guide slightly.

  • Page 10: To Thread Bobbin Case

    TO THREAD BOBBIN CASE Holding the bobbin case in your left hand, turn the open Guide the thread into the slot side up and place the threaded in the edge of the bobbin case bobbin into it (Fig. 1). Pull it under the tension spring (Fig.

  • Page 11: To Insert Bobbin Case Into The Machine

    TO INSERT BOBBIN CASE INTO THE MACHINE Raise the needle bar and take-up lever both to their highest point. Open the slide plate. Hold the bobbin case by the latch and place it on the centre post with the bobbin case finger in the notch at the top of the shuttle. Release the latch and press the bobbin case into the shuttle until the latch catches on the centre post with a click.

  • Page 12: Right Needle And Thread For Right Cloth

    RIGHT NEEDLE AND THREAD FOR RIGHT CLOTH Size of Needles Cloth Size of Threads No. 80-100 cotton thread or fine silk No. 9 Thin calico, silk, serge and muslin. thread. Thin calico, cotton cloth, crepe de No. 60-100 cotton thread or ordinary No.

  • Page 13: To Thread Needle

    TO THREAD NEEDLE Raise the take-up lever (5) to the highest point by turning the balance wheel toward you. Place a spool of thread on the spool pin. Pass the thread through upper arm thread guide (1), downwards around tension discs (2) from right to left, up over the tension thread guard (3) from behind, through the loop of the take-up spring (4), up and through the hole in the take-up lever (5), down through thread guides (6&7) and into the thread guide (8)

  • Page 14: To Raise Lower Thread

    TO RAISE LOWER THREAD Hold the upper thread loosely with your left hand, Turn the balance wheel towards you with your right hand until the needle and the thread take-up lever move down and lip again, both to their highest point, then stop the balance wheel and pull the upper thread slowly to bring up the lower thread through the needle hole, Place both ends of the threads back under the presser foot.

  • Page 15: To Regulate Tension Of Upper Thread

    TO REGULATE TENSION OF UPPER THREAD For ordinary stitching the tension of the upper and lower threads should be set so as to lock both threads in the centre of the fabric. (A) If the tension of the upprr thread is too strong, the upper thread will lie straight along the upper surface of the fabric as shown in (B).

  • Page 16: Tension Of Lower Thread

    TENSION OF LOWER THREAD The tension or the lower thread is regulated· by a small screw on the bobbin case tension spring. To increase the tension, tighten the screw slightly with a small driver. To decrease the tension, loosen the screw slightly. TO USE BUILT- IN SEWLIGHT Sewlight is connected directly to the main supply lead of the machine when the motor plug is inserted into the connector.

  • Page 17: To Adjust Pressure On Presser Foot

    TO ADJUST PRESSURE ON PRESSER FOOT For releasing pressure on the foot, press down the ring (A), which will allow the pressure regulator to spring up to its highest position and leave the material free from any pressure from the presser foot. For sewing thin or light fabrics, press the top of the A pressure regulator (B) down lightly to get the required slight pressure of the fabric.

  • Page 18: To Regulate Length Of Stitch And Direction Of Feed

    TO REGULATE LENGTH OF STITCH AND DIRECTION OF FEED To regulate the length of stitch, turn the For reverse stitching, first adjust the stitch stitch length regulator knob (1) to show the length control knob (1) to obtain the desired required stitch length in the stitch indicator stitch length and then push in the reverse window (2).

  • Page 19: Straight Sewing And Zigzag Sewing

    STRAIGHT SEWING AND ZIGZAG SEWING For straight sewing, set the zigzag width Zigzag stitch is controlled by the zigzag width control control knob at "0". knob on the arm of this machine. Make sure the presser foot is for straight By moving this control knob gradually to the left toward sewing.

  • Page 20: Manual Zigzag Pattern Sewing

    MANUAL ZIGZAG PATTERN SEWING By manually adjusting the stitch length and zigzag width while running the machine, some beautiful ornamental stitches can be made as follows: Stitch Stitch Patterns Width Patterns Width Length Length long long and Set to any point from 1 to 5. short Set to any point from 0 to 5.

  • Page 21: Buttonhole Sewing

    BUTTONHOLE SEWING 1.Remove the regular presser foot and attach the buttonhole fool. 2.Set the zigzag width knob between “1” and “2”. Set the stitch length regulator knob to obtain close stitches (satin stitch). 3. Mark with a pencil or chalk the position and exact length of the buttonhole on the fabric.
  • Page 22 4.Lower the needle carefully into the mark on the fabric indicating the beginning o f buttonhole. Lower the presser foot and commence sewing the left row of the buttonhole until it reaches the end of the marking. (1) Stop the machine with needle on fabric at point A. 5.Lift the presser foot and using the needle as a pivot, turn the fabric end for end to bring the buttonhole to position (2).

  • Page 23: Darning And Embroidery

    DARNING AND EMBROIDERY Raise the presser bar lifter and remove the presser foot. Then lower the presser bar lifter to ensure the thread tension device is set correctly. Set the drop feed knob at "EMBR". Now your machine is ready for embroidery and darning. Embroidery will be done most successfully when the fabric is stretched and fixed in an embroidery hoop.

  • Page 24: Hemming

    HEMMING Raise the needle to its highest point. Raise the presser bar, remove the regular presser foot, and attach a hemmer foot. Fold over the edge of the fabric approximately 1/8 inch wide, then fold it over again In the same way for a length of about 2 inches.

  • Page 25: Sewing In A Zipper

    SEWING IN A ZIPPER The zipper foot included in the accessories enables you to attach a zipper on fabric. Remove the regular presser foot and attach the zipper foot to the presser bar of the machine. First open out the zipper and place fabric 111 the position under the needle.

  • Page 26: Button Sewing

    BUTTON SEWING Fit the button sewing tool to the machine. Set the drop feed button at "EMBR." With the button sewing tool In a raised position, place a button on the fabric with its holes in a horizontal line and the left side hole underneath the needle, and lower the fool upon it.

  • Page 27: Blind Stitch Hem

    BLIND STITCH HEM With the fabric inside out, fold it to the desired size of the hem. (No. 1) Fold it again with a 1/4 inch overlap on the bottom fold. (No. 2) Set the zigzag width control knob at "3" and the stitch length regulator knob at about "2", and sew on the fold.

  • Page 28: To Clean Shuttle Race

    TO CLEAN SHUTTLE RACE Because your machine is specially equipped with the shuttle thread ejector which prevents jamming of the shuttle, it will rarely be necessary to open and clean the shuttle-race. However, if for some reason it should ever be required to open and clean the shuttle-race, its design enables you to do this most easily and conveniently without sacrificing the precise fit which is so essential to the efficient working...
  • Page 29 TO O IL MACHINE Apply a few drops of fine quality sewing machine oil to the points indicated by the arrows in the figures. In constant use, oil two or three times a week. In case the machine does not work smoothly due to standing idle for some time, apply a few drops of paraffin at the oiling points, and run the machine rapidly for a minute.

  • Page 30: Care And Adjustment Of The Motor

    CARE AND ADJUSTMENT OF THE MOTOR ATTACHING THE MOTOR TO THE MACHINE PLACING THE BELT ON THE MOTOR Place the motor bracket (A) on the boss (B) Slip the belt into the groove in the balance on the arm, with which the slot in the motor wheel, and force it into the groove in the bracket fits.
  • Page 31 To adjust the belt tension, loosen the attaching screw about one turn with a screwdriver. This will allow the motor to drop downward. Then firmly tighten the screw, and the belt should have the correct tension.
  • Page 32 SUGGESTIONS FOR SMOOTH SEWING Machine Working Heavily See if the shuttle race, feed dog and underneath parts of the needle plate arc clogged with lint. If so, clean out the pan. If the machine works hard after standing for some time, apply a little paraffin in place of oil. Then run the machine rapidly to clean the bearings, and oil the machine with sewing machine oil.

  • Page 33: Skipped Stitches

    CONTINUED SUGGESTIONS FOR SMOOTH SEWING Skipped Stitches A bent or blunt pointed needle is often the cause of this. See that the needle is accurately inserted. Remove the needle plate, and, after ascertaining that the feed is clean and working freely, reset the needle plate.

  • Page 34: Appendix A - Compatible Parts List

    Appendix A – Compatible Parts List Class 15 Metal Bobbins. Bobbin Kenmore Models: 385.11101 385.11206 385.11607 385.11608 385.11682 385.12014 385.12102 385.12116 385.12216 385.12314 385.12318 385.12514 385.12545 385.12581 385.12612 385.12614 385.12618 385.12712 385.12714 385.12781 385.12812 385.12814, 385.12912 385.12916 385.12049 385.15008 385.15510 385.15512 385.15516 385.15518. Singer Models: 15-30 15K30 15-80 15-86 15-87 15-88 15-96 15-97 15-111 15-112 Needle Plate Sears/Kenmore Model 33 158.330, Model 1024...

  • Page 35: Appendix B

    Now, from what I’m gathering, at this time Janome of Japan created numerous machines for export including the ones branded “Janome” , ”New Home” and “Imperial”. Also, from what I understand they produced these machines in an unbranded fashion. The sharp eyed of you will have noticed that in all of the pictures in the manual there is no logo in where the logo plate should be.

Table of Contents