Page 1: Table Of Contents
2006 Escape Hybrid www.hillerford.com Table of Contents Introduction Instrument Cluster Warning and control lights Gauges Entertainment Systems AM/FM stereo cassette with CD AM/FM stereo with in-dash six CD Navigation system Climate Controls Manual heating and air conditioning Rear window defroster...
Page 2 Table of Contents Seating and Safety Restraints Seating Safety restraints Airbags Child restraints Tires, Wheels and Loading Tire Information Tire Inflation Vehicle loading Trailer towing Recreational towing Driving Starting Brakes Transmission operation Roadside Emergencies Getting roadside assistance Hazard flasher switch Fuel pump/High voltage shut-off switches Fuses and relays Changing tires...
Page 4: Introduction
The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it. For more information on Ford Motor Company and its products visit the following website: • In the United States: www.ford.com •...
Page 5 Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.
Page 6 Introduction NORMAL VEHICLE OPERATION Your Escape Hybrid has unique qualities which cause it to operate differently than a typical vehicle. Starting the vehicle • The engine will start and run when you first turn the ignition key to the start position. •...
Page 7 Introduction Transmission operation • Your vehicle does not shift like a conventional vehicle. You may feel transitions between the various operating modes of the hybrid system, but no actual shifting occurs. For more information about transmission operation, refer to Understanding the gearshift positions of the electronically-controlled Continuously Variable Transaxle (eCVT) in the Driving chapter.
Page 8 Introduction • You may hear a slight whine or whistle when operating your vehicle. This noise could occur at idle, and during cruising and accelerating; it is caused by the normal operation of electrical generator in the hybrid system. • The Escape Hybrid’s hydraulic brake system used for regenerative braking is different from other vehicles.
Page 9 Introduction the climate control system to A/C mode or A/C mode also reduces fuel economy, but in this case the A/C only operates when the engine is already running due to other demands. Because the engine does not run continuously, A/C and A/C mode are more fuel efficient than MAX A/C mode.
Page 10 • where the driver was positioning the steering wheel. To access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event data recorder information without obtaining consent,...
Page 11 Your vehicle is not equipped with a snowplowing package. Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Your vehicle is not equipped with the Ford Ambulance Preparation Package. Cell phone use The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs.
Page 12 Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation Child Seat Lower Warning Anchor Child Seat Tether Brake System Anchor Brake Fluid -...
Page 13 Introduction Vehicle Symbol Glossary Power Windows Power Window Lockout Front/Rear Interior Luggage Child Safety Door Compartment Release Lock/Unlock Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, Battery Acid or Sparks Explosive Gas Fan Warning Maintain Correct Fluid...
Page 14: Instrument Cluster
Instrument Cluster WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to test and make sure the bulb works.
Page 15 Instrument Cluster Service soon: The Service soon indicator illuminates when the vehicle has detected a malfunction. Report the fault to a dealer at the earliest opportunity. Brake system warning light: To confirm the brake system warning light is functional, it will BRAKE momentarily illuminate when the ignition is turned to the RUN...
Page 16 Instrument Cluster Safety belt: Reminds you to fasten your safety belt. A chime will also sound to remind you to fasten your safety belt. If this light continues to flash the chime will sound again to remind you to fasten your safety belt. Master vehicle electrical hazard warning lamp: Indicates Hybrid component fault/failure that will...
Page 17 Instrument Cluster Never remove the coolant reservoir cap while the engine is running or hot. ABS active/Traction control active (if equipped): Flashes when the ABS system is active. If the light remains on, have the system serviced immediately, refer to the Driving chapter for more information.
Page 18: Gauges
Instrument Cluster Message center activation chime: Sounds when a warning message appears in the message center display for the first time. Message center switch activation chime: Sounds when the message center INFO or SET control is pressed. GAUGES Speedometer: Indicates the current vehicle speed.
Page 19 Instrument Cluster Trip odometer: Registers the miles (or kilometers) of individual journeys. To reset, press and hold the trip reset button for two or more seconds; this returns the trip odometer to zero. Press and release the button to return to the odometer display.
Page 20: Entertainment Systems
Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 21 Entertainment Systems 2. CD Eject: Press to eject a CD. The radio will resume playing. 3. Mute: Press to MUTE playing media; press again to return to the playing media. 4. Tape Eject: Press to eject the cassette. The radio will resume playing.
Page 22 Entertainment Systems Dolby: In tape mode, press MENU until DOLBY B XX appears in the display. Press SEL to toggle ON/OFF. The Dolby noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation. Dolby and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation.
Page 23 Entertainment Systems button press to proceed to the next/last text display. ) The last text field shown on the display will become the new display message default. TEXT is also available when equipped with Satellite radio. Your radio comes equipped with Satellite ready capability. The kit to enable Satellite reception is available through your dealer.
Page 24 Entertainment Systems 18. Scan: Press to hear a brief sampling of all listenable stations, tape selections or CD tracks. Press again to stop. 19. Tune/CAT: TUNE: Works in radio mode only. Press TUNE to change frequency down/up. CAT: CAT is only available when equipped with Satellite Radio. Your radio comes equipped with Satellite ready capability.
Page 25: Am/Fm Stereo With In-Dash Six Cd
Entertainment Systems Audiophile Satellite Compatible AM/FM Stereo In-Dash Six CD Radio (if equipped) 1. SEEK: Press and release SEEK for previous/next strong station or track. 2. REW (Rewind): In CD mode, press until desired selection is reached. FF (Fast forward): In CD mode, press until desired selection is reached. TEXT: TEXT is only available when equipped with Satellite radio.
Page 26 Entertainment Systems • ALL SEATS — Enhances acoustic sound for all seating locations. • DRIVERS SEAT — Enhances acoustic sound for the driver. Rear seat and passenger seat performance may be compromised in favor of the driver. • REAR SEATS - Enhances acoustic sound for the rear seat passengers. 4.
Page 27 Entertainment Systems Traffic: Allows you to hear traffic broadcasts. With the feature ON, press SEEK or SCAN to find a station broadcasting a traffic report (if it is broadcasting RDS data). Traffic information is not available in most U.S. markets. FIND Program type: Allows you to search RDS-equipped stations for a certain category of music format: Classic, Country, Info, Jazz, Oldies, R&B, Religious, Rock, Soft, Top 40.
Page 28 Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed.
Page 29 CD to play. CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular...
Page 30 Entertainment Systems shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels.
Page 31 Entertainment Systems 5. CLK (Clock): Press to alternate between clock display and audio display. Note: If the audio operation is selected while the clock mode is on, the selected audio mode will be displayed for ten seconds, then the display will revert to the clock mode.
Page 32 Entertainment Systems 14. LOAD: The load feature allows you to load up to six single CDs into the audio system. Press LOAD. “In” will appear in the display when the system is ready. Insert the CD. Autoload: To load up to six CDs into the system: Press and hold LOAD until a beep is heard.
Page 33 Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 34: Navigation System
Ford Motor Company shall not be liable for any damages of any type arising from failure to follow these guidelines. Do not attempt to service, repair or modify the system. See your Ford or Lincoln Mercury dealer. The driver must not attempt to operate any detailed operation of the navigation system while the vehicle is in motion.
Page 35 • Set the volume level so that you can hear directions clearly. • Do not disassemble or modify the system as this may lead to damage and void your warranty. If a problem occurs, stop using the system immediately and contact your Ford or Lincoln Mercury dealer.
Page 36 Entertainment Systems System overview 1. CD slot: Insert an audio CD, label side up. 2. Eject: Press this control to eject an audio CD or a navigation CD. 3. Navigation (NAV): Press the NAV control to access the navigation system menu. 4.
Page 37 Entertainment Systems 6. ENTER: Use this control when viewing a menu in the navigation system. Press the control up or down, left or right to highlight an item in the display. Press the center of the control to make your selection. 7.
Page 38 Entertainment Systems Turn the control to adjust the audio volume levels. To adjust the voice output levels from the navigation system, adjust the volume levels only during voice output. 14. Phone (if equipped): If the phone button is pressed and a phone is not present, this will mute the playing media.
Page 39 Entertainment Systems Quick start – how to get going To play a radio station: 1. Ensure that the ignition and the Vehicle Navigation Radio (VNR) system are ON. 2. Press the AM/FM control to select the desired frequency band. 3. Press the SEEK control to locate a station.
Page 40 Entertainment Systems 2. Press the NAV control to enter into Navigation mode. 3. To enter a destination, ensure that the vehicle is in the PARK position. 4. To navigate to home from the current location, press HOME. If a home location has not previously been stored, pressing and holding HOME will store the home location.
Page 41 Entertainment Systems 4. HV Battery: This icon represents your High Voltage Battery. The fill level (shown in green), represents the state of charge of the HV Battery and will go up and down as the battery charges/discharges during normal operation. 5.
Page 42 Entertainment Systems The vehicle is slowing down and power is being stored in the high voltage (HV) battery by the Hybrid system. The vehicle is in a state similar to idle, except that power is being generated to recharge the high voltage battery.
Page 43 Entertainment Systems The vehicle is either at rest, or is sharing very little power between the Hybrid parts. This can occur at higher speeds if the vehicle is not speeding up or slowing down. The vehicle is driving in electric mode.
Page 44 Entertainment Systems • Average Fuel Economy (AFE): The AFE is displayed on the white bar across the graph. The AFE will be retained when the key is turned OFF, and will continue averaging when driving resumes. Pressing RESET will reset the AFE to zero. •...
Page 45 Entertainment Systems Volume/power control Press the control to turn the audio/navigation system on or off. Turn the control to raise or lower volume. The levels will be displayed on the screen. To adjust the navigation voice output level, adjust the volume control only when the navigation system is speaking.
Page 46 Entertainment Systems 4. Select AVC. 5. Use the cursor control to increase or decrease the levels. The higher the level selected, the greater the compensation. The levels will be shown in the display. Decrease all the way to the left to turn AVC off. AM/FM select The AM/FM control works in radio, CD and navigation modes.
Page 47 Entertainment Systems • Station overload. Weak signals are sometimes captured by stronger signals when you pass a broadcast tower. A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed. AM/FM select in navigation mode Press once when in navigation mode to return to the audio screen (while the navigation function continues to work in the background).
Page 48 Entertainment Systems 3. Select BASS, TREB (Treble), BAL (Balance) or FADE. The bass adjust allows you to increase or decrease the audio system’s bass output. The treble adjust control allows you to raise or lower the audio system’s treble output. The balance feature allows sound distribution to be adjusted between the right and left speakers.
Page 49 Entertainment Systems • REAR — Optimizes the audio playback for rear seat passengers. Rewind/fast forward Press the controls to fast forward or rewind a CD track. Seek function The SEEK control works in all modes. Seek in radio mode • Press to find the next listenable station down the frequency band.
Page 50 Entertainment Systems Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until PRESET SAVED appears on the display.
Page 51 Entertainment Systems Tune adjust The tune feature works in radio mode. • Select the TUNE soft key. • Press SEEK to go up down the frequency band manually. Stereo indicator Whenever a stereo signal is received in radio mode, the stereo indicator (ST) will appear in the display.
Page 52 Entertainment Systems Select the TRAF soft key to select traffic information broadcast from certain stations which will automatically interrupt radio or CD playback at a preset volume level. The default Traffic volume can be adjusted with the slider bar using the cursor input. Moving the position to the left most position will turn this feature off.
Page 53 Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 54 Entertainment Systems 2. Insert one disc into each CD tray of the magazine (up to 6 discs). Ensure that the label side is facing If you pull too hard on the disc holder, the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine.
Page 55 Entertainment Systems Radio power must be turned on to play the CDs in the CD DJ. The magazine may be stored in the glove compartment when not being used. The CD magazine may be inserted or ejected with the radio power off. Ensure that the disc holder is evenly inserted and at the same level as the magazine (A).
Page 56 Entertainment Systems Rewind/fast forward feature When in CD DJ mode, press and hold the control to search forward or in reverse on the current disc. Scan feature When in CD DJ mode, press SCAN for a brief sampling of all tracks on the current CD.
Page 57 Entertainment Systems Navigation features The route guidance navigation system in your audio unit will not function unless a navigation CD is inserted. Ensure that you follow highway code restrictions and do not take any risks. For example, if you are unable to make a U-turn, continue on your journey.
Page 58 Entertainment Systems Principles of GPS (Global Positioning System) operation Your Vehicle Navigation System directs you based on information derived from satellites, road maps stored on the CD, sensors in your vehicle and the desired destination. The system compiles all necessary information to guide you to your selected destination.
Page 59 Entertainment Systems Use the cursor control, or the corresponding soft key to confirm your selection. If you select the wrong item, press the BACK control to return to the previous screen. Or, press NAV to return to the main Destination Entry menu and start again.
Page 60 Entertainment Systems Address/Intersection Use the soft keys to select Address/Intersection from the Destination Entry menu. The next two options available are: • Town/City Name – Select this option if you know the town or city name. • Street Name – Select if you know the street address but are uncertain of the city.
Page 61 Entertainment Systems • Sort by Distance – Lists the closest POI entries to the vehicle’s current location. • Within a Town/City – Lists entries for a specific city in alphabetical order. Note: The intersection function is not available when the vehicle is moving.
Page 62 Entertainment Systems Entering a destination using the keyboard of lists After selecting the desired choice from the Destination Entry menu, there are two main ways to enter your destination in the VNR system: Keyboard – the keyboard display enables you to spell out a town, city, street or point of interest.
Page 63 Entertainment Systems 5. Use freeways — Creates a route which uses freeways where possible. Route calculation Once the route criteria is selected, the navigation system automatically calculates a route to the selected destination. The route appears on the display screen and a voice prompt provides instructions. This screen will appear for a few seconds while the navigation system is calculating your route.
Page 64 Entertainment Systems Guide display Once your vehicle is moving along the highlighted route, the Guide display screen will automatically appear. This screen shows your next turn as voice prompts direct you on the route. When the planned route contains incomplete map data, the guide display maneuvers are identified in “cautionary”...
Page 65 Entertainment Systems Arrival When you approach your destination, the destination indicator will appear on the map display screen as a circular icon. When you arrive, the name and address of your destination will be displayed. Navigation screen display The address book feature allows you to store up to 50 alphabetical destinations.
Page 66 Entertainment Systems 6. Press the EDIT soft key to edit the current entry. • Use the cursor control to select a letter. • Push the control to add a letter to the name. If you make a mistake, you can press the DELETE soft key.
Page 67 Entertainment Systems Detours, route interruptions and changes If need be, your navigation system can easily and quickly find the most efficient detour around road construction, unexpected traffic or undesirable roads. Detour options You may engage the detour option when in the Guide display, True view or Map display screens.
Page 68 Entertainment Systems • Resume route - The navigation system displays the Select Route Criteria screen. Refer to Selecting Route Criteria earlier in this chapter. • Cancel route - Press to return to the main menu. If the ignition is not turned off, simply continue along your highlighted route.
Page 69 Entertainment Systems • UNITS — Press to select from miles or kilometers. When kilometers are selected, it will affect the map and the fuel economy screen. Display options Use this feature to change the display setting. This feature can be accessed by selecting “Display Options”...
Page 70 General information Federal Communication Commission (FCC) Compliance Changes or modifications not approved by Ford or Lincoln Mercury could void user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 71 Entertainment Systems • Always store the map CDs in their protective cases when not in use. Map coverage Please refer to the In-dash Navigation System Quick Start Guide for individual map CD content details. CDs contain map data for all of the continental United States and parts of Canada.
Page 72: Climate Controls
Climate Controls MANUAL HEATING AND AIR CONDITIONING SYSTEM 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control.
Page 73: Rear Window Defroster
Climate Controls Operating tips • To reduce fog build up on the windshield during humid weather, place the air flow selector in the position. • To reduce humidity build up inside the vehicle in cold weather: do not drive with the air flow selector in the O (OFF), A/C or MAX A/C position.
Page 74: Lights
Lights HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. Headlamp battery saver The battery saver will shut off the exterior lamps 10 minutes after the ignition switch has been turned off if the headlamp control is in position.
Page 75 Lights 1. Turn the key to the 1 (LOCK) position. 2. Rotate the headlamp control to the autolamp position. 3. Rotate the headlamp control to the OFF position. 4. Turn the key to the 3 (RUN) position. 5. Turn the key back to the 1 (LOCK) position.
Page 76 Lights Daytime running lamps (DRL) (if equipped) Turns the lowbeam headlamps on with a reduced output. To activate: • the ignition must be in the 3 (RUN) position. • the headlamp control must be in the OFF, parking lamps or autolamp position.
Page 77 Lights PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel. • Push and hold top of control to brighten. • Push and hold bottom of control to dim. AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician.
Page 78: Turn Signal Control
Lights 3. Turn on the low beam headlamps to illuminate the wall or screen and open the hood. Cover the left-hand headlamp with an opaque cloth. 4. On the wall or screen you will observe a light pattern with a distinct horizontal edge of high intensity light towards the right.
Page 79 Lights The dome lamp control has three positions: • OFF: In this position, the lamp will not illuminate. • DOOR: In this position, the dome lamp will illuminate only when a door is opened and will remain illuminated for 25 seconds after the door is shut. •...
Page 80: Bulb Replacement
Lights BULB REPLACEMENT Headlamp Condensation The headlamps are vented to equalize pressure. When moist air enters the headlamp(s) through the vents, there is a possibility that condensation can occur. This condensation is normal and will clear within 45 minutes of headlamp operation. Replacing exterior bulbs Check the operation of all the bulbs frequently.
Page 81 Lights Replacing headlamp bulbs 1. Make sure that the headlamp control is in the OFF position and open the hood. 2. Press down on the wire retainer to release it and access the back of the headlamp assembly. Lowbeam bulb replacement 3.
Page 82 Lights Note: If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used. To complete installation, follow the removal procedure in reverse order. Replacing brake/tail/turn/backup lamp bulbs The brake/tail/turn/backup lamp bulbs are located in the tail lamp assembly, one just below the other.
Page 83 Lights Replacing license plate lamp bulbs 1. Make sure the headlamp switch is in the OFF position and then pry the license plate lamp assembly (located above the license plate) from the liftgate. 2. Remove bulb socket from lamp assembly by turning counterclockwise.
Page 84 Lights Replacing front parking lamp/turn signal bulbs For bulb replacement, see a dealer or qualified technician. Replacing foglamp bulbs For bulb replacement, see a dealer or qualified technician.
Page 85: Driver Controls
Driver Controls MULTI-FUNCTION LEVER Windshield wiper: For intermittent operation, move control down one position. Adjust the rotary control to the desired speed setting. For normal or low speed wiper operation, move control down two positions from OFF. For high speed wiper operation, move control down three positions from OFF.
Page 86: Steering Wheel Adjustment
Driver Controls Rear window wiper/washer controls For intermittent operation of rear wiper, rotate end of control upward to the position. For normal speed rear wiper operation, rotate control upward to To activate the rear washer, rotate the control to the position and release.
Page 87 Driver Controls AUXILIARY POWER POINT (12V) Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug.
Page 88 Driver Controls Note: The 110 VAC power point is equipped with a safety cap and a safety twist tab. They both provide protection from inserting any object into the power point other than the 110 VAC electrical device plug. The safety cap should always be in a closed position whenever the power point outlet is not in use.
Page 89: Power Windows
Driver Controls Indicator light Code Green light is On — Power point is ready to supply power Green light is Off — Power point power supply is off. Ignition is not in RUN position Green light is blinking — Power point is in fault mode POWER WINDOWS Do not leave children unattended in the vehicle and do not let children play with the power windows.
Page 90: Mirrors
Driver Controls Window lock (if equipped) The window lock feature disables all the power windows except the driver’s. To lock out all the window controls except for the driver’s window press the right side of the control. Note: The window switches will not illuminate when the window control is in the LOCKED position.
Page 91: Speed Control
Driver Controls Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place.
Page 92 Driver Controls • If the vehicle speed increases above the set speed on a downhill, you may want to shift into “L” gear and/or apply the brakes to reduce the speed. • If the vehicle speed decreases more than 10 mph (16 km/h) below your set speed on an uphill, your speed control will disengage.
Page 93 Driver Controls • Depress the brake pedal until the desired vehicle speed is reached, press the SET ACC control. Disengaging speed control There are two ways to disengage the speed control: • Depress the brake pedal or the clutch pedal (if equipped). This will not erase your vehicle’s previously set speed.
Page 94 Driver Controls 1. Power point 2. Cupholders 3. Utility compartment 4. Ash cup (if equipped) Use only soft cups in the cupholders. Hard objects can injure you in a collision. MOON ROOF (IF EQUIPPED) To operate the moon roof: • The moon roof is equipped with an automatic, one-touch, express opening feature.
Page 95: Message Center
Driver Controls MESSAGE CENTER With the ignition in the RUN position, the message center, located on your instrument cluster, displays important vehicle and daily driving information through a constant monitor of vehicle systems. You may select display features on the message center for a display of status preceded by a brief indicator chime.
Page 96 Driver Controls Average fuel economy (AFE) (if equipped) This function will display your average fuel economy in miles/gallon or liters/100 km. If you calculate your average fuel economy by dividing gallons of fuel used by 100 miles traveled (kilometers traveled by liters used), your figure may be different than displayed for the following reasons: •...
Page 97 Driver Controls Instantaneous fuel economy (if equipped) Press INFO until the menu displays “INSTANT ECON”. This will display your fuel economy as a Bar Graph ranging from “L” poor economy to “H” excellent economy. Your vehicle must be moving to calculate instantaneous fuel economy.
Page 98 Driver Controls 7. Exterior Lamps 8. Power Steering 9. 4 Wheel Drive (if equipped) Units (English/Metric) 1. Select this function from the INFO menu for the current units to be displayed. 2. Press the SET control to change the message display from English to Metric.
Page 99 Driver Controls The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the SET control and clearing the warning message. Warning messages that have been reset are divided into two categories: •...
Page 100 Driver Controls Warnings Status Liftgate ajar Warning returns after the ignition key is turned from LOCK to RUN. Service emission sys Check fuel cap Low brake fluid Service brake system Regen disabled Performance reduced Check left headlamp Check right headlamp Check left high beam Check right high beam Check left turn lamps...
Page 101 Refer to Engine coolant in the Maintenance and Specifications chapter. If the warning stays on or continues to come on, contact your Ford Dealer as soon as possible. Never remove the coolant reservoir cap while the engine is running or hot.
Page 102 Driver Controls SERVICE BRAKE SYSTEM. Displayed when the braking system is not operating properly. If the warning stays on or continues to come on, contact your dealer as soon as possible. REGEN DISABLED. Indicates the regen system is disabled at this moment.
Page 103 • Fuel computer • Oil life • Charging system • Door sensor • Washer fluid • Brake fluid • Engine sensor Contact your Ford dealer as soon as possible if these messages occur on a regular basis.
Page 104 Driver Controls LIFTGATE To open the rear window, pull the right side of the liftgate handle. To open the liftgate, pull the left side of the liftgate handle. • Do not open the liftgate or liftgate glass in a garage or other enclosed area with a low ceiling.
Page 105 Driver Controls Ensure that the posts are properly latched in mounting features. The cover may cause injury in a sudden stop or accident if it is not securely installed. Do not place any objects on the cargo area shade. They may obstruct your vision or strike occupants of vehicle in the case of a sudden stop or collision.
Page 106 Driver Controls To remove the cross-bar assembly from the roof rack side rails: 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable). 2. Slide the cross-bar to the end of the rail. 3. Use a long, flat object to depress the tongue in the endcaps on both sides of the cross-bar.
Page 107 Driver Controls To reinstall the cross-bar assembly to the roof rack side rails: 1. Ensure that both cross-bar assemblies are installed with the F (front) arrow facing towards the front of the vehicle. 2. Use a long, flat object to depress the tongue in the endcaps on both sides of the cross-bar.
Page 108: Locks And Security
Locks and Security KEYS One key operates all locks and starts the vehicle. Always carry a spare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your dealer supplied keys, replacement keys are available through your authorized dealer.
Page 109 Locks and Security 7. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position. The horn will chirp one time to confirm the programming mode has been exited. Repeat the procedure to turn the feature on or off. Door key unlocking/locking Two step door unlocking 1.
Page 110 Locks and Security Relock This feature will also automatically relock all the doors when: • the ignition is in the 3 (RUN) position and any door is opened then closed, and • you put the vehicle in motion by releasing the brake pedal. Deactivating/activating the autolock feature The autolock feature can be activated or deactivated using the following procedure:...
Page 111 Locks and Security CHILDPROOF DOOR LOCKS • When these locks are set, the rear doors cannot be opened from the inside. • The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door.
Page 112 Locks and Security The remote entry system allows you to lock or unlock all vehicle doors without a key. The remote locking and unlocking features will operate independent of the ignition position; however, the panic feature will only operate when the ignition is in the 1 (LOCK) or 2 (ACCESSORY) position.
Page 113 Locks and Security For more information concerning the perimeter alarm, refer to Perimeter alarm system (if equipped) later in this chapter. 2. Press and release again within three seconds to confirm that all the doors and liftgate are closed and locked. Note: The doors will lock again and the horn will chirp once.
Page 114 Locks and Security 2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery.
Page 115 Locks and Security To reprogram the remote entry transmitters: 1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. Turn the key from the 1 (LOCK) position to 3 (RUN). 4. Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK) position and 3 (RUN).
Page 116: Anti-Theft System
Note: The SecuriLock passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues.
Page 117 Locks and Security Replacing coded keys can be very costly. Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. Please visit an authorized dealer to purchase additional spare or replacement keys. Programming spare keys You can program your own coded keys to your vehicle.
Page 118 Locks and Security 8. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position. Keep the ignition in the 3 (RUN) position for at least three seconds but not more than 10 seconds. 9. Remove the newly programmed coded key from the ignition. If the key has been successfully programmed it will start the vehicle’s engine and the theft indicator light will illuminate for three seconds and then go out.
Page 119 Locks and Security When the vehicle is locked, the alarm is set after a 20–second arming period. When you press the control on the remote entry transmitter twice within three seconds, the horn will chirp once to confirm the doors, liftgate and hood are closed and locked, and the alarm is set.
Page 120: Seating And Safety Restraints
Seating and Safety Restraints FRONT SEATS Notes: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
Page 121 Seating and Safety Restraints Adjusting the front manual seat Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Adjusting the front power seat (if equipped) The control is located on the outboard side of the seat cushion. Press to raise or lower the front portion of the seat cushion.
Page 122 Seating and Safety Restraints Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Heated seats (if equipped) To operate the heated seats: • Push the control located on the seat to activate.
Page 123 Seating and Safety Restraints The head restraints can be moved up and down. Lift the head restraint so that it is located directly or as close as possible behind your head. Push control to lower or remove head restraint. Folding down rear seats 1.
Page 124 Seating and Safety Restraints 3. Pull the seat release control. Note: Make sure the floor is clear of all objects before folding the seat. 4. Flip seat forward. Attach the safety belt web snap button to the quarter trim panel snap button.
Page 125 Seating and Safety Restraints 5. To release seatback, pull the seatback release lever (on top of seat) toward the front seat. This is common for both 60% and 40% seatbacks. Note: When the seatback release lever is pulled, slowly lower seatback to the flat position.
Page 126 Seating and Safety Restraints 2. Rotate seat cushion down into the seating position making sure that the seat cushion is locked into place and that the safety belt buckles are exposed. Make sure safety belt buckle heads are through elastic holders on seat backs.
Page 127: Safety Restraints
Seating and Safety Restraints To remove the rear cushion 1. Lift the yellow tab to release the hinges. 2. Pull the cushion to the outboard side of the vehicle. To install the rear cushion 1. Push the cushion to the inboard side of the vehicle.
Page 128 Seating and Safety Restraints • Restraints Control Module (RCM) with impact and safing sensors • Restraint system warning light and back-up tone • The electrical wiring for the airbags, crash sensor(s), safety belt pretensioners, front safety belt usage sensors, driver seat position sensor, passenger occupant classification sensor, and indicator lights How does the Safety System work? The Safety System can adapt the deployment strategy of your vehicle’s...
Page 129 Seating and Safety Restraints is designed to help protect smaller drivers sitting close to the driver airbag by providing a lower airbag output level. Front passenger sensing system For airbags to do their job they must inflate with great force, and this force can pose a potentially deadly risk to occupants that are very close to the airbag when it begins to inflate.
Page 130 Seating and Safety Restraints allows your Safety System to tailor the airbag deployment and safety belt pretensioner activation depending upon safety belt usage. Refer to Safety belt section in this chapter. Front safety belt pretensioners The safety belt pretensioners at the front outboard seating positions are designed to tighten the safety belts firmly against the occupant’s body during frontal collisions, and in side collisions and rollovers when the vehicle is equipped with the Safety Canopy system.
Page 131 Seating and Safety Restraints If any of these things happen, even intermittently, have the Safety System serviced at your dealership or by a qualified technician immediately. Unless serviced, the system may not function properly in the event of a collision. Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Page 132 Seating and Safety Restraints Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them.
Page 133 Seating and Safety Restraints All safety belts in the vehicle are combination lap and shoulder belts. The passenger safety belts have two types of locking modes described below: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
Page 134 Seating and Safety Restraints • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
Page 135 Seating and Safety Restraints Safety belt height adjustment Your vehicle has safety belt height adjustments at the front outboard seating positions. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To adjust the shoulder belt height, squeeze and hold the buttons on the side and slide the height adjuster up or down.
Page 136 (if equipped), shoulder belt guide on seatback (if equipped), child safety seat LATCH and tether anchors, and attaching hardware, should be inspected after a collision. Ford Motor Company recommends that all safety belt assemblies in use in vehicles involved in a collision be replaced.
Page 137 Seating and Safety Restraints Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... Then... The driver’s safety belt is not The safety belt warning light buckled before the ignition illuminates 1 minute and the warning...
Page 138 I’m not going far 3 of 4 fatal crashes occur within 25 miles of home. Belts are Ford designs its safety belts to enhance comfort. If uncomfortable you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible;...
Page 139 Seating and Safety Restraints Reasons given... Consider... I was in a hurry Prime time for an accident. BeltMinder reminds us to take a few seconds to buckle up. Seat belts don’t Safety belts, when used properly, reduce risk of work death to front seat occupants by 45% in cars, and by 60% in light trucks.
Page 140 Seating and Safety Restraints Read Steps 1 - 4 thoroughly before proceeding with the deactivation/activation programming procedure. The driver and front passenger BeltMinder features can be deactivated/activated by performing the following procedure: Before following the procedure, make sure that: • The parking brake is set •...
Page 141: Airbags
Seating and Safety Restraints AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly; there is a risk of injury from a deploying airbag.
Page 142 Do not attempt to service, repair, or modify the airbag supplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer. Modifications to the front end of the vehicle, including frame,...
Page 143 Seating and Safety Restraints Children and airbags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision.
Page 144 Seating and Safety Restraints The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder or sodium compounds which may irritate the skin and eyes, but none of the residue is toxic.
Page 145 Seating and Safety Restraints Front passenger sensing system The front passenger sensing system will turn off the front passenger’s frontal airbag under certain conditions. The front passenger seat-mounted side airbag (if equipped) will be deactivated if the sensor detects an empty seat; otherwise, the seat-mounted side airbag will be enabled.
Page 146 Seating and Safety Restraints The indicator light is located in the center stack of the instrument panel just below the radio. The front passenger sensing system is designed to turn off the front passenger’s frontal airbag when a rear facing infant seat, a forward-facing child restraint, or a booster seat is detected.
Page 147 If it is necessary to modify an advanced front airbag system to accommodate a person with disabilities, contact the Ford Customer Relationship Center at the phone number shown in the Customer Assistance section of this Owner’s Guide.
Page 148 Do not attempt to service, repair, or modify the airbag SRS, its fuses or the seat cover on a seat containing an airbag. See your Ford or Lincoln Mercury dealer. All occupants of the vehicle should always wear their safety belts...
Page 149 Seating and Safety Restraints How does the side airbag system work? The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group.
Page 150 Seating and Safety Restraints to inflate in side-impact collisions, not roll-over, rear-impact, frontal or near-frontal collisions, unless the collision causes sufficient lateral deceleration. Several air bag system components get hot after inflation. Do not touch them after inflation. If the side airbag has deployed, the airbag will not function again.
Page 151 Do not attempt to service, repair, or modify the Safety Canopy system, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing a Safety Canopy . See your Ford or Lincoln Mercury dealer. All occupants of the vehicle including the driver should always...
Page 152 Seating and Safety Restraints How does the Safety Canopy system work? The design and development of the Safety Canopy system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group.
Page 153 Seating and Safety Restraints The Safety Canopy is mounted to roof side-rail sheet metal, behind the headliner, above the first and second row seats. The Safety Canopy designed to inflate between the side window area and occupants to further enhance protection provided in side impact collisions and rollover events.
Page 154: Child Restraints
Seating and Safety Restraints • A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and/or light are repaired. If any of these things happen, even intermittently, have the SRS serviced at your dealership immediately. Unless serviced, the system may not function properly in the event of a collision.
Page 155 To improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats, Ford Motor Company recommends use of a belt-positioning booster. Booster seats position a child so that safety belts fit better. They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably.
Page 156 Seating and Safety Restraints • Can the child stay seated like this for the whole trip? Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt.
Page 157 Seating and Safety Restraints Follow all instructions provided by the manufacturer of the booster seat. Never put the shoulder belt under a child’s arm or behind the back because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision. Never use pillows, books, or towels to boost a child.
Page 158 80 lb. (36 kg) using an upper torso harness and a belt-positioning booster. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position with LATCH and tether anchors.
Page 159 Seating and Safety Restraints 1. Position the child safety seat in a seat with a combination lap and shoulder belt. Children 12 and under should be properly restrained in the rear seat whenever possible. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together.
Page 160 Seating and Safety Restraints 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it.
Page 161 Seating and Safety Restraints 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly tilt the seat forward and back to make sure the seat is securely held in place. To check this, grab the seat at the belt path and attempt to move it side to side and forward and back.
Page 162 Seating and Safety Restraints 3. Locate the correct anchor for the selected seating position. There are three tether anchors located on the headliner at the rear of the vehicle. 4. Clip the tether strap to the anchor as shown. The arrow in the above graphic points toward the front of the vehicle.
Page 163 Seating and Safety Restraints Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments for child seat anchors Some child safety seats have two rigid or webbing mounted attachments that connect to two anchors at certain seating positions in your vehicle. This type of child seat eliminates the need to use safety belts to attach the child seat.
Page 164 Seating and Safety Restraints The lower anchors for child seat installation are located at the rear section of the second row seat between the cushion and seat back. Follow the child seat manufacturer’s instructions to properly install a child seat with LATCH attachments. Attach LATCH lower attachments of the child seat only to the anchors shown.
Page 165: Tires, Wheels And Loading
Tires, Wheels and Loading NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed...
Page 166 Tires, Wheels and Loading Power is supplied to all four wheels through a transfer case or power transfer unit. You should become thoroughly familiar with this information before you operate your vehicle. Do not become overconfident in the ability of 4WD and AWD vehicles.
Page 167: Tire Information
10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford Motor Company to give you the following information about tire grades exactly as the government has written it.
Page 168 Tires, Wheels and Loading government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.
Page 169: Tire Inflation
Tires, Wheels and Loading • Tire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacture. • Inflation pressure: A measure of the amount of air in a tire. •...
Page 170 (if equipped), at least monthly and before long trips. You are strongly urged to buy a reliable tire pressure gauge, as automatic service station gauges may be inaccurate. Ford Motor Company recommends the use of a digital or dial-type tire pressure gauge rather than a stick-type tire pressure gauge.
Page 171 Always inflate your tires to the Ford recommended inflation pressure even if it is less than the maximum inflation pressure information found on the tire. The Ford recommended tire inflation pressure is found on the Safety Compliance Certification Label which is located on the B-Pillar or the edge of the driver’s door.
Page 172 Only use replacement tires and wheels that are the same size and type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.
Page 173 Tires, Wheels and Loading INFORMATION CONTAINED ON THE TIRE SIDEWALL Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S.
Page 174 Tires, Wheels and Loading 7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time under a standard condition of load and inflation pressure. The tires on your vehicle may operate at different conditions for load and inflation pressure.
Page 175 Tires, Wheels and Loading 10. Tire Ply Composition and Material Used: Indicates the number of plies or the number of layers of rubber-coated fabric in the tire tread and sidewall. Tire manufacturers also must indicate the ply materials in the tire and the sidewall, which include steel, nylon, polyester, and others.
Page 176 Tires, Wheels and Loading Additional information contained on the tire sidewall for “LT” type tires “LT” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the Tire and Rim Association (T&RA), that is intended for service on light trucks.
Page 177 Tires, Wheels and Loading Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
Page 178 Tires, Wheels and Loading the road in adverse (wet, snowy, etc.) conditions. Visually check your tires for uneven wear, looking for high and low areas or unusually smooth areas. Also check for signs of tire damage. When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to prevent your vehicle from skidding and hydroplaning.
Page 179 If your vehicle seems to pull to one side when you’re driving, the wheels may be out of alignment. Have a qualified technician at a Ford or Lincoln Mercury dealer check the wheel alignment periodically.
Page 180 Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Ford or Lincoln Mercury dealership to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation.
Page 181: Vehicle Loading
• Do not use cables or chains on dry roads. • Do not exceed 30 mph (48 km/h) with tire cables or chains on your vehicle. Consult your dealer for information on other Ford approved methods of traction control. VEHICLE LOADING – WITH AND WITHOUT A TRAILER...
Page 182 Tires, Wheels and Loading Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the Tire Label on the B-Pillar or the edge of the driver’s door (vehicles exported outside the US and Canada may not have a Tire Label).
Page 183 Tires, Wheels and Loading Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight.
Page 184 Tires, Wheels and Loading GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door.
Page 185 Tires, Wheels and Loading GVWR (Gross Vehicle Weight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door.
Page 186 Tires, Wheels and Loading 10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheel trailer), and driver only (150 lb. [68 kg]). Consult your dealership (or the RV and Trailer Towing Guide provided by your dealership) for more detailed information. Tongue Load or Fifth Wheel King Pin Weight –...
Page 187 Tires, Wheels and Loading 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. The following gives you a few examples on how to calculate the available amount of cargo and luggage load capacity: •...
Page 188: Trailer Towing
Tires, Wheels and Loading Special loading instructions for owners of pickup trucks and utility-type vehicles For important information regarding safe operation of this type of vehicle, see the Preparing to drive your vehicle section in the Driving chapter of this Owner’s Guide. Loaded vehicles may handle differently than unloaded vehicles.
Page 189 Tires, Wheels and Loading • Refer to the instructions included with towing accessories for the proper installation and adjustment specifications. Do not exceed the maximum loads listed on the Certification label. For load specification terms found on the label, refer to Vehicle loading in this chapter.
Page 190 Tires, Wheels and Loading Do not exceed the GVWR or the GAWR specified on the certification label. Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury.
Page 191 Tires, Wheels and Loading connect trailer lamps directly to your vehicle’s tail lamps. This can cause damage to your vehicle’s electrical system. See your dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps. Driving while you tow When towing a trailer: •...
Page 192: Recreational Towing
Tires, Wheels and Loading When backing down a ramp during boat launching or retrieval: • do not allow the static water level to rise above the bottom edge of the rear bumper. • do not allow waves to break higher than 6 inches (15 cm) above the bottom edge of the rear bumper.
Page 193: Driving
Driving STARTING Positions of the ignition 1. LOCK, locks the gearshift lever and allows key removal. 2. ACCESSORY, allows the electrical accessories such as the radio to operate while the vehicle is not running. 3. RUN, all electrical circuits operational and warning lights will illuminate.
Page 194 Driving Before starting the vehicle: 1. Make sure all occupants buckle their safety belts. For more information on safety belts and their proper usage, refer to the Seating and Safety Restraints chapter. 2. Make sure the headlamps and electrical accessories are off. 3.
Page 195 Driving Starting the vehicle 1. Turn the key to 3 (RUN) without turning the key to 4 (START). If there is difficulty in turning the key, rotate the steering wheel until the key turns freely. This condition may occur when: •...
Page 196: Brakes
Driving Important ventilating information If the engine is idling while the vehicle is stopped for a long period of time, open the windows at least one inch (2.5 cm) or adjust the heating or air conditioning to bring in fresh air. USING THE ENGINE BLOCK/HIGH VOLTAGE BATTERY HEATER (IF EQUIPPED) An engine block/high voltage battery heater warms the engine coolant...
Page 197 Driving keeping the brakes from locking. The hydraulic brake system used for regenerative braking is different from other vehicles. The noise from the ABS pump motor and the brake pedal pulsation are much less than on vehicles with conventional ABS. Noise and pedal pulsation during ABS may not be noticed.
Page 198 Driving energy of motion back into the battery to improve fuel economy. The standard brake system is designed to fully stop the car if regenerative braking is not available. During regenerative braking, the motor is spun as a generator to create electrical current. This recharges the high voltage battery and slows the vehicle.
Page 199 Driving more effort. Under extreme usage conditions, the steering effort may increase. This occurs to prevent overheating and permanent damage to your steering system. If this should occur, you will neither lose the ability to steer the vehicle manually nor will it cause permanent damage. When you can safely pull your vehicle off to the side of the road, the vehicle should be turned off until it is able to cool.
Page 200: Transmission Operation
Driving AUTOMATIC TRANSMISSION OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the RUN position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the RUN position and the brake pedal depressed, it is possible that a fuse has blown or the vehicle’s brake lamps are not operating properly.
Page 201 Driving Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly.
Page 202 Driving R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle is free to roll; hold the brake pedal down while in this position.
Page 203 Driving REVERSE SENSING SYSTEM (IF EQUIPPED) The Reverse Sensing System (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when R (Reverse) is selected and the vehicle is moving at speeds less than 3 mph (5 km/h). The system is not effective at speeds above 3 mph (5 km/h) and may not detect certain angular or moving objects.
Page 204 Driving The RSS detects obstacles up to 6 ⁄ feet (2 meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper, (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases.
Page 205 Driving FOUR WHEEL DRIVE (4WD) SYSTEM (IF EQUIPPED) For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter. Your vehicle is equipped with an intelligent 4WD System that continuously monitors vehicle conditions and automatically adjusts the power distribution between the front and rear wheels.
Page 206 Driving Maintain steering wheel control at all times, especially in rough terrain. Since sudden changes in terrain can result in abrupt steering wheel motion, make sure you grip the steering wheel from the outside. Do not grip the spokes. Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps.
Page 207 Driving If your vehicle gets stuck If your vehicle gets stuck in mud or snow it may be rocked out by shifting between forward and reverse gears, stopping between shifts, in a steady pattern. Press lightly on the accelerator in each gear. Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur.
Page 208 Driving Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions.
Page 209 Ford Motor Company joins the U.S. Forest Service and the Bureau of Land Management in encouraging you to help preserve our national forest and other public and private lands by “treading lightly.”...
Page 210 The suspension and steering systems on your vehicle have been designed and tested to provide durable load carrying capability and predictable performance whether loaded or empty. For this reason, Ford Motor Company strongly recommends that you do not make modifications such...
Page 211 Ford Motor Company recommends that caution be used with any vehicle equipped with a high load or device (such as ladder racks or pickup box cover).
Page 212: Roadside Emergencies
50,000 miles (80,000 km) on Lincoln vehicles. Roadside assistance will cover: • a flat tire change with a good spare (except Ford GT which has a tire inflation kit) • battery jump start • lock-out assistance (key replacement cost is the customer’s responsibility) •...
Page 213: Hazard Flasher Switch
1–800–241–3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who require roadside assistance, call 1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673;...
Page 214 Roadside Emergencies The fuel pump shut-off switch is located in the front passenger’s footwell, behind a flip-up cover. The high voltage shut-off switch is located in the cargo area on the passenger side of the vehicle in the jack compartment, behind the jack access door.
Page 215: Fuses And Relays
Roadside Emergencies If you see or smell fuel, do not reset the fuel pump shut-off or try to start your vehicle; you could injure yourself or others. Have all the passengers get out of the vehicle and call the local fire department or a towing service.
Page 216 Roadside Emergencies COLOR Cartridge Fuse Mini Standard Maxi Fuse link maxi rating fuses fuses fuses cartridge fuses — — — Brown — — Natural — Black Passenger compartment fuse panel The fuse panel is located on the right-hand side of the center console, by the instrument panel.
Page 217 Roadside Emergencies The fuses are coded as follows: Fuse/Relay Fuse Amp Passenger Compartment Fuse Panel Location Rating Description — Not used Spare 15A* Front and rear park lamps 10A* Ignition switch Powertrain Control Module (PCM relay), PATS module 15A* Stop lamps 10A* Instrument cluster, Power mirror switch, Radio...
Page 218 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Panel Location Rating Description 15A* Moon roof Radio — Not used — Not used 30A** Power windows 15A* Subwoofer 15A* Low beams 10A* — Not used 15A* Horn 10A* Rear wiper motor, Rear wiper washer 10A* Instrument cluster Spare...
Page 219 Roadside Emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the low voltage (underhood) battery before servicing high current fuses. To reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the low voltage (underhood) battery or refilling fluid reservoirs.
Page 220 Roadside Emergencies Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating 7.5A* Traction (high voltage) Battery Control Module (TBCM), Powertrain Control Module (PCM) Interlock 15A* PCM power 15A* Heated Exhaust Gas Oxygen (HEGO) sensors 10A* TCM VPWR 20A* Fuel pump 30A* Bussed power feed to PDB fuses 1, 2, 3, 4 20A*...
Page 221 Roadside Emergencies Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating 50A** PSCM #2 Relay Power sustain for PCM, TBCM and Transaxle Control Module (TCM) Relay PCM power Relay Injector Relay Auxiliary coolant pump Relay Motor/Electronic coolant pump Relay Foglamps Relay A/C clutch Diode 01...
Page 222: Changing Tires
Roadside Emergencies Fuse/Relay Location Description Relay 1 Driver side cooling fan Relay 2 Passenger side cooling fan (low-speed) Relay 3 Passenger side cooling fan (high-speed) CHANGING A FLAT TIRE If you get a flat tire while driving: • do not brake heavily. •...
Page 223 Ford. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired.
Page 224 Roadside Emergencies • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a dissimilar spare tire/wheel and seek service as soon as possible. Tire change procedure When one of the front wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park).
Page 225 Roadside Emergencies Removing the jack and tools Non-cargo management system (if equipped):The jack and tools are located under the carpeted hardboard. Pull back the carpet away from the lift gate, and remove the hardboard cover. Unbuckle the strap and remove the jack and tools by pulling the right side up first.
Page 226 Roadside Emergencies To remove jack from vehicle: 1. Release the thumbscrew on the bracket. 2. Release the retention clip on the upper part of the jack bracket. 3. Dislodge the jack from the bracket and carefully guide jack down and out through trim opening, upper end out first.
Page 227 Roadside Emergencies If equipped with a tether, perform the following additional steps: 4. Lift the spare tire on end to access tether attachment (1). 5. Use the lug wrench to remove the lug nut from the spare tire tether. 6. If not replacing the spare or flat tire to the underbody storage area, raise winch up into the installed position.
Page 228 Roadside Emergencies Changing the flat tire 8. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. Before placing the jack under the vehicle, NOTE the jack locations: • Front...
Page 229 Roadside Emergencies • Rear 9. Lower the jack from its stored height to fit under the jacking notches. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 1 inch (25 mm) off the ground.
Page 230 Roadside Emergencies 11. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. 12.
Page 231 Roadside Emergencies • guide the jack bottom first in the trim opening and position in the bracket (3), • secure the retention clip on the upper part of the jack (2), and • close the thumbscrew (1). Make sure the jack is fastened so it does not rattle when you drive.
Page 232: Lug Nut Torque
Roadside Emergencies 1. Place tire on end with valve stem facing rearward, away from vehicle. 2. Place tether into bolt holes in wheel and attach lug nut using lug wrench. 3. Lay the tire on the ground with the valve stem facing down. If your vehicle is equipped with aluminum wheels, remove the wheel ornament.
Page 233: Jump Starting
M12 x 1.5 * Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners. When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the front disc brake hub and rotor that contacts the wheel.
Page 234 Roadside Emergencies relearning process. This is a normal condition and will not re-occur until the low voltage battery is disconnected again. 1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery of the disabled vehicle as this could damage the vehicle’s electrical system.
Page 235 Roadside Emergencies 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.
Page 236 Roadside Emergencies 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Page 237 Roadside Emergencies Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2.
Page 238 Roadside Emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 239 Roadside Emergencies The high voltage battery contains potassium hydroxide (a strong alkaline electrolyte) which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your vehicle. This vehicle does not have push-start capability. If you attempt to start your vehicle and the engine cranks but does not start, the high voltage battery may need to be jump started.
Page 240 Roadside Emergencies If the engine still does not start after the first complete high voltage jump start, a second jump start procedure can be attempted after a two-minute period (indicated by the button light changing from a rapid flash to no illumination). This jump start procedure can only be done twice before the low voltage (underhood) battery becomes discharged and must also be jump started.
Page 241: Wrecker Towing
It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. On FWD vehicles, if your vehicle is to be towed from the front, ensure proper wheel lift equipment is used to raise the front wheels off the ground.
Page 242 • Maximum distance is 50 miles (80 km). • Maximum speed is not to exceed 35 mph (56 km/h). Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for...
Page 243: Customer Assistance
Center at 1-800-392-3673 (FORD). Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Page 244 If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Page 245 Customer Assistance In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the...
Page 246 THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Company vehicles. The Dispute Settlement Board may not be available in all states. Ford...
Page 247 • The name of the dealer(s) who sold or serviced the vehicle. • A brief description of your unresolved concern. • A brief summary of the action taken by the dealer(s) and Ford Motor Company. • The names (if known) of all the people you contacted at the dealership(s).
Page 248 After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.
Page 249 United States and Canada, provided by a network of more than 4,600 participating Ford or Lincoln Mercury and Ford of Canada dealers. If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this...
Page 250 Customer Assistance information is subject to change, please ask your dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www.ford-esp.com. GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact the appropriate foreign embassy or consulate.
Page 251: Reporting Safety Defects (U.s. Only)
Obtaining a French owner’s guide French Owner’s Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3. REPORTING SAFETY DEFECTS (U.S. ONLY)
Page 252: Cleaning
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is available from your dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid.
Page 253 Cleaning racks, bumpers, side moldings, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the parts over time. PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color. Take your color code (printed on a sticker in the driver’s door jamb) to your dealer to ensure you get the correct color.
Page 254 Cleaning • Cover the highlighted areas to prevent water damage when cleaning the engine. Note: As with all transmissions, be especially careful as water entry into the vents can damage internal parts. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage.
Page 255 Cleaning This washer fluid contains special solution in addition to alcohol which helps to remove the hot wax deposited on the wiper blade and windshield from automated car wash facilities. • Do not use abrasives, as they may cause scratches. •...
Page 256 Flush the complete underside of your vehicle frequently. Keep body and door drain holes free from packed dirt. FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury dealer has many quality products available to clean your vehicle and protect its finishes. These quality products...
Page 257 Cleaning have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from high quality materials that meet or exceed rigid specifications. For best results, use the following products or products of equivalent quality: Motorcraft Bug and Tar Remover (ZC-42) Motorcraft Car Care Kit (ZC-26)
Page 258: Maintenance And Specifications
Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service.
Page 259 Maintenance and Specifications 1. High voltage connector shield 2. Service Disconnect 3. High voltage battery case Working with the engine off 1. Set the parking brake and shift to P (Park). 2. Turn off the engine and remove the key. 3.
Page 260 Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2. At the front of the vehicle, lift up on the auxiliary latch handle located in the center between the hood and the grille. 3.
Page 261: Engine Compartment
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Engine coolant reservoir 2. Motor/Electronics (M/E) coolant reservoir 3. Engine oil filler cap 4. Brake fluid reservoir 5. Power distribution box 6. Low Voltage (underhood) battery 7. Engine air filter assembly 8.
Page 262 In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specifications. Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive.
Page 263: Engine Oil
Maintenance and Specifications CHANGING THE WIPER BLADES 1. Pull the wiper blade and arm away from the glass. Turn the blade at a right angle to the arm. Push the lock tab (A) to release the blade from the arm loop and pull the blade down toward the windshield to remove it from the arm.
Page 264 Maintenance and Specifications 5. Locate and carefully remove the engine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is within the MIN and MAX marks or the lower and upper holes, the oil level is acceptable.
Page 265 Approval Committee (ILSAC), comprised of U.S. and Japanese automobile manufacturers. To protect your engine’s warranty use Motorcraft SAE 5W-20 or an equivalent 5W-20 oil meeting Ford specification WSS-M2C930-A. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for your vehicle’s engine.
Page 266: Battery
Maintenance and Specifications Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced.
Page 267 Maintenance and Specifications Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.
Page 268 Maintenance and Specifications • The vehicle may need to be driven 10 miles (16 km) or more to relearn the idle and fuel trim strategy. • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.
Page 269 Maintenance and Specifications Checking engine coolant The concentration and level of engine coolant should be checked at the mileage intervals listed in Scheduled Maintenance information. The coolant concentration should be maintained at 50/50 coolant and distilled water, which equates to a freeze point of -34°F (-36°C).
Page 270 Maintenance and Specifications Checking motor/electronics (M/E) coolant The M/E coolant reservoir is located behind the engine coolant reservoir. Refer to the following engine coolant sections for all information, instructions and warnings related to cooling systems. The two systems use the same coolant and operate similarly, with the Motor and Electronics system generally operating at a lower temperature...
Page 271 • Add Motorcraft Premium Gold Engine Coolant (yellow-colored), VC-7–A (U.S., except CA, OR and NM), VC-7–B (CA, OR and NM), meeting Ford Specification WSS-M97B51–A1. Note: Use of Motorcraft Cooling System Stop Leak Pellets, VC-6, may darken the color of Motorcraft Premium Gold Engine Coolant from yellow to golden tan.
Page 272 Maintenance and Specifications • Do not use alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating or freezing. • Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion protection of the engine coolant.
Page 273 Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled engine coolant in vehicles originally equipped with Motorcraft Premium Gold Engine Coolant since a Ford-approved recycling process is not yet available.
Page 274: Fuel Information
Maintenance and Specifications • Decreased engine coolant concentrations below 40% will decrease the corrosion protection characteristics of the engine coolant and may cause engine damage. • Decreased engine coolant concentrations below 40% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage.
Page 275 Maintenance and Specifications Automotive fuels can cause serious injury or death if misused or mishandled. Gasoline may contain benzene, which is a cancer-causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle.
Page 276 Maintenance and Specifications When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes. The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is pumped into an ungrounded fuel container.
Page 277 The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. Remove fuel filler cap slowly.
Page 278 Ask your fuel supplier about gasolines that meet the World-wide Fuel Charter. Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines to improve air quality. Running out of fuel Avoid running out of fuel because this situation may have an adverse...
Page 279 Maintenance and Specifications If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine. •...
Page 280 Maintenance and Specifications 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odometer reading from the current odometer reading. 5. Follow one of the simple calculations in order to determine fuel economy: Calculation 1: Divide total miles traveled by total gallons used.
Page 281 Maintenance and Specifications Maintenance • Keep tires properly inflated and use only recommended size. • Keep wheels properly aligned. • Use recommended engine oil. Refer to Lubricant specifications in this chapter. • Perform all regularly scheduled maintenance items. Follow the recommended maintenance schedule and owner maintenance checks found in scheduled maintenance information.
Page 282 If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
Page 283 Maintenance and Specifications Board Diagnostics System (OBD-II). This OBD-II system protects the environment by ensuring that your vehicle continues to meet government emission standards. The OBD-II system also assists the service technician in properly servicing your vehicle. When the Check engine/Service engine soon light illuminates, the OBD-II system has detected a malfunction.
Page 284 Maintenance and Specifications BRAKE FLUID The fluid level will drop slowly as the brakes wear, and will rise when the brake components are replaced. Check fluid levels with the ignition in the RUN position. Fluid levels between the “MIN” and “MAX” lines are within the normal operating range;...
Page 285 Maintenance and Specifications Note: The brake system on the Escape Hybrid can only be bled at a authorized dealer. TRANSMISSION FLUID Checking electronically controlled continuously variable transmission (eCVT) Refer to your scheduled maintenance information chapter for scheduled intervals for fluid checks and changes. Your transaxle does not consume fluid.
Page 286 Maintenance and Specifications 5. Using the hole in the splash shield, remove the check plug from the side of the transmission. If this is the first check of the transmission fluid, it may be necessary to remove the perforated section of the splash shield (as indicated on the splash shield).
Page 287: Air Filter(S)
Maintenance and Specifications 7. The fluid level should be within 1/4 inch (6 mm) of the plug threads. 8. Replace the check plug. Adjusting eCVT fluid levels Before adding any fluid, make sure the correct type is used. The type of fluid used is indicated in the Lubricant specifications section in this chapter.
Page 288 Maintenance and Specifications Changing the air filter element 1. Release the clamps that secure the air filter housing cover. 2. Carefully separate the two halves of the air filter housing. 3. Remove the air filter element from the air filter housing. 4.
Page 289: Part Numbers
Maintenance and Specifications Changing the high voltage battery air filter element 1. Remove access panel located in the rear cargo area on the driver’s side trim panel to expose the filter cover. 2. Push the tabs (located on each side of filter cover) while pulling gently to remove filter cover.
Page 290 Refer to scheduled maintenance information chapter for the appropriate intervals for changing the PCV valve. Replace the PCV valve with one that meets Ford material and design specifications for your vehicle, such as a Motorcraft or equivalent replacement part. The customer warranty may be void for any damage to the emissions system if such a PCV valve is not used.
Page 291: Refill Capacities
Maintenance and Specifications REFILL CAPACITIES Fluid Ford Part Application Capacity Name Brake fluid Motorcraft High Between MIN Performance and MAX lines DOT 3 Motor on reservoir Vehicle Brake Fluid Engine oil Motorcraft SAE 2.3L I4 engine 4.5 quarts (including filter 5W-20 Premium (4.25L)
Page 292 Fill to 1/4 inch to 9/16 inch (6 mm to 14 mm) below bottom of fill hole. Use of synthetic or synthetic blend motor oil is not mandatory. Engine oil need only meet the requirements of Ford specification WSS-M2C930-A and the API Certification mark.
Page 293: Lubricant Specifications
Maintenance and Specifications LUBRICANT SPECIFICATIONS Item Ford Part Ford Part Ford Name or Number Specification equivalent Body hinges, Multi-Purpose XG-4 or XL-5 ESB-M1C93-B latches, door Grease striker plates and rollers, seat tracks, fuel filler door hinge and spring, primary and auxiliary...
Page 294 4WD vehicles exposed for prolonged periods to temperatures less than –40° C (-40° F) should change out the rear axle fluid to Motorcraft SAE 75W-140 High Performance Rear Axle Lubricant, Ford part number XY-75W140–QL meeting Ford specification WSL-M2C192–A.
Page 295 Maintenance and Specifications ENGINE DATA Engine 2.3L I4 engine Cubic inches Required fuel 87 octane Firing order 1-3-4-2 Ignition system Coil on plug Spark plug gap 0.049–0.053 inch (1.25–1.35mm) Compression ratio 12.3:1 HIGH VOLTAGE BATTERY DATA High Voltage Battery Battery chemistry Nickel Metal Hydride Nominal Voltage 330 Volts...
Page 296 Maintenance and Specifications...
Page 297 Maintenance and Specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structure by the trailing edge of the driver’s door or...
Page 298 Maintenance and Specifications The Vehicle Identification Number (VIN) contains the following information: 1. World manufacturer identifier 2. Brake type and Gross Vehicle Weight Rating (GVWR) 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7.
Page 299: Accessories
In addition, each accessory is made from high quality materials and meets or exceeds Ford’s rigorous engineering and safety specifications. Ford Motor Company will repair or...
Page 300 Accessories Lifestyle Ash cup Bike racks Cargo organization and management Smoker’s Package Peace of mind First aid and highway safety kits Full vehicle covers Locking gas cap For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: •...
Page 301: Scheduled Maintenance Guide
Your Ford or Lincoln Mercury dealer, or Ford or Lincoln Mercury Quality Care Center has factory trained technicians who can perform the required maintenance using genuine Ford parts. They are committed to meeting your service needs and to assuring your continuing satisfaction.
Page 302 Lincoln Mercury dealership for all your vehicle’s needs. Get the most from your service and maintenance visits There are a lot of reasons why your Ford and Lincoln Mercury dealership is a great way to help keep your vehicle running great.
Page 303: Owner Checks And Services
Scheduled Maintenance Guide WHICH MAINTENANCE SCHEDULE SHOULD YOU FOLLOW? Owner Checks and Services Refer to Mileage Intervals for Additional Checks and Services Certain basic maintenance checks and inspections should be performed by the owner or a service technician at the intervals indicated. Service information and supporting specifications are provided in this Owner’s Guide.
Page 304: Normal Scheduled Maintenance And Log
ADDITIONAL INFORMATION AVAILABLE ON THE WEB To learn more about the importance of routine and dealer-performed maintenance on your vehicle, please visit the Ford Customer Service Web site. You’ll also find important warranty information, customer assistance, technical expertise, frequently asked questions and much more. The Web site location is: www.ford.com.
Page 305 Scheduled Maintenance Guide U.S. SCHEDULE 5,000 miles (8,000 km) ❑ Inspect tires for wear and measure tread depth ❑ EALER ALIDATION Rotate tires RO#: P&A C ILEAGE 10,000 miles (16,000 km) ❑ Change engine oil and replace oil filter ❑ EALER ALIDATION Inspect tires for wear and measure tread depth...
Page 306 Scheduled Maintenance Guide 30,000 miles (48,000 km) ❑ Change engine oil and replace oil filter ❑ EALER ALIDATION Inspect tires for wear and measure tread depth ❑ Rotate tires ❑ Inspect high voltage battery A/C filter, replace if necessary ❑ Replace engine air filter RO#: P&A C...
Page 307 Scheduled Maintenance Guide 60,000 miles (96,000 km) ❑ Change engine oil and replace oil filter ❑ Inspect tires for wear and measure tread depth EALER ALIDATION ❑ Rotate tires ❑ Inspect brake pads, shoes, rotors, drums, brake lines and hoses and parking brake ❑...
Page 308 Scheduled Maintenance Guide 90,000 miles (144,000 km) ❑ Change engine oil and replace oil filter ❑ EALER ALIDATION Inspect tires for wear and measure tread depth ❑ Rotate tires ❑ Inspect high voltage battery A/C filter, replace if necessary ❑ Replace engine air filter RO#: P&A C...
Page 309 Scheduled Maintenance Guide 120,000 miles (192,000 km) ❑ Change engine oil and replace oil filter ❑ Inspect tires for wear and measure tread depth EALER ALIDATION ❑ Rotate tires ❑ Inspect brake pads, shoes, rotors, drums, brake lines and hoses and parking brake ❑...
Page 310 Scheduled Maintenance Guide 150,000 miles (240,000 km) ❑ Change engine oil and replace oil filter ❑ Inspect tires for wear and measure tread depth EALER ALIDATION ❑ Rotate tires ❑ Replace high voltage battery A/C filter ❑ Replace engine air filter ❑...
Page 311 Scheduled Maintenance Guide 18,500 miles (30,000 km) ❑ Change engine oil and replace oil filter* ❑ Inspect tires for wear and measure tread depth ❑ Inspect brake pads, shoes, rotors, drums, brake lines and EALER ALIDATION hoses and parking brake ❑...
Page 312 Scheduled Maintenance Guide 47,000 miles (75,000 km) ❑ Change engine oil and replace oil filter* ❑ EALER ALIDATION Inspect tires for wear and measure tread depth ❑ Inspect high voltage battery A/C filter, replace if necessary* ❑ Multipoint inspection* RO#: P&A C ILEAGE 56,000 miles (90,000 km)
Page 313 Scheduled Maintenance Guide 75,000 miles (120,000 km) ❑ Change engine oil and replace oil filter* ❑ Inspect tires for wear and measure tread depth ❑ Inspect brake pads, shoes, rotors, drums, brake lines and hoses and parking brake ❑ Inspect engine and motor/electrical cooling system and hoses EALER ALIDATION ❑...
Page 314 Scheduled Maintenance Guide 103,000 miles (165,000 km) ❑ Change engine oil and replace oil filter* ❑ EALER ALIDATION Inspect tires for wear and measure tread depth ❑ Inspect high voltage battery A/C filter, replace if necessary* ❑ Multipoint inspection* RO#: P&A C ILEAGE 112,000 miles (180,000 km)
Page 315 Scheduled Maintenance Guide 130,000 miles (210,000 km) ❑ Change engine oil and replace oil filter* ❑ Inspect tires for wear and measure tread depth ❑ Inspect brake pads, shoes, rotors, drums, brake lines and EALER ALIDATION hoses and parking brake ❑...
Page 316 Scheduled Maintenance Guide 159,000 miles (255,000 km) ❑ Change engine oil and replace oil filter* ❑ EALER ALIDATION Inspect tires for wear and measure tread depth ❑ Inspect high voltage battery A/C filter, replace if necessary* ❑ Multipoint inspection* RO#: P&A C ILEAGE 168,000 miles (270,000 km)
Page 317: Special Operating Conditions
Scheduled Maintenance Guide 188,000 miles (300,000 km) ❑ Change engine oil and replace oil filter* ❑ Inspect tires for wear and measure tread depth ❑ Inspect brake pads, shoes, rotors, drums, brake lines and EALER ALIDATION hoses and parking brake ❑...
Page 318: Special Operating Conditions And Log
Scheduled Maintenance Guide SPECIAL OPERATING CONDITIONS Towing a trailer or using a camper or car-top carrier Every 3,000 miles or 3 months Change engine oil and replace filter Extensive Idling and/or Low Speed Driving for Long Distances as in Heavy Commercial Use Such as Delivery, Taxi, Patrol Vehicle or Livery.
Page 319 Scheduled Maintenance Guide Special Operating Conditions Log EALER ALIDATION EALER ALIDATION RO#: P&A C RO#: P&A C ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION RO#: P&A C RO#: P&A C ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION RO#: P&A C RO#: P&A C ILEAGE ILEAGE EALER...
Page 320 Scheduled Maintenance Guide Special Operating Conditions Log EALER ALIDATION EALER ALIDATION RO#: P&A C RO#: P&A C ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION RO#: P&A C RO#: P&A C ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION RO#: P&A C RO#: P&A C ILEAGE ILEAGE EALER...
Page 321 Scheduled Maintenance Guide Motorcraft Premium Engine Gold Coolant ❑ 5 years or 100,000 miles (160,000 km) - change Motorcraft Premium Engine Coolant (whichever comes first) ❑ After initial change - change Motorcraft Premium Engine Coolant every 3 years or 50,000 miles (80,000 km) Current mileage goes here =>...
Page 322: Index
Index acid, treating emergencies ..266 jumping a disabled battery ......233, 238 Accessory delay ......90 maintenance-free ....266 Air cleaner filter ....287–289 replacement, specifications ...289 Airbag supplemental restraint servicing ........266 system ......141, 148, 151 BeltMinder .........137 and child safety seats ....143 Brakes ........196 description ....141, 148, 151 anti-lock ......196–197 disposal ........154...
Page 323 Emission control system ..281 Cruise control (see Speed control) ....91 Engine ........295 cleaning ........253 Customer Assistance ....212 idle speed control ....266 Ford Extended Service lubrication Plan ..........249 specifications ....293, 295 Getting assistance outside the refill capacities ......291 U.S. and Canada .....250 service points ......261...
Page 324 Index Foglamps ........76 Head restraints ....120, 122 Four-Wheel Drive vehicles Headlamps ........74 driving off road .......205 aiming ........77 preparing to drive your autolamp system .......74 vehicle ........199 bulb specifications ....80 Fuel ..........274 daytime running lights .....76 calculating fuel flash to pass ......75 economy ......96, 279 cap ...........276 high beam .........75...
Page 325 Index Mirrors fold away ........90 heated ........91 Lamps side view mirrors (power) ..90 autolamp system .......74 Moon roof ........94 bulb replacement specifications chart ....80 Motorcraft parts ..256, 274, 289 daytime running light ....76 fog lamps ........76 headlamps .........74 Navigation system .......34 headlamps, flash to pass ..75 quick start .........39 instrument panel, dimming ..77...
Page 326 Index Rear window defroster ....73 Seat belts (see Safety restraints) .....127 Relays ........215 Seats ..........120 Remote entry system child safety seats ....157 illuminated entry ....115 heated ........122 locking/unlocking doors ..108 Servicing your vehicle ....258 Reverse sensing system ...203 Setting the clock Roadside assistance ....212 AM/FM/In-dash 6 CD ..26, 31 Roof rack ........105...
Page 327 Index spare tire ......222–223 Vehicle loading ......181 terminology ......168 Ventilating your vehicle ...196 tire grades .......168 treadwear ......167, 177 Towing ........188 recreational towing ....192 Warning lights (see Lights) ..14 trailer towing ......188 wrecker ........241 Washer fluid ......262 Transmission ......200 Water, Driving through .....211 brake-shift interlock (BSI) ..200 fluid, checking and adding Windows...

This manual is also suitable for:

Escape hybrid

Ford 2006 Escape Hybrid Owner's Manual

Introduction

Instrument Cluster

Entertainment Systems

Climate Controls

Lights

Driver Controls

Locks and Security

Seating and Safety Restraints

Tires, Wheels and Loading

Driving

Roadside Emergencies

Customer Assistance

Maintenance and Specifications

Accessories

Scheduled Maintenance Guide

Index

Quick Links

Table of Contents

Related Manuals for Ford 2006 Escape Hybrid

Summary of Contents for Ford 2006 Escape Hybrid

This manual is also suitable for:

Table of Contents