Page 1: Installation Manual
KX-TDA200 KX-TDA100 Model Panasonic KX-TDA100, KXTDA100, KX-TDA200, KXTDA200 Thank you for purchasing a Panasonic Hybrid IP-PBX. Please read this manual carefully before using this product and save this manual for future use. SD Logo is KX-TDA100/KX-TDA200: Version 2.0 a trademark.
Page 2: System Components
System Components System Components Table Model Description Shelves KX-TDA100 Basic Shelf KX-TDA200 Basic Shelf Main Processing Main Processing Card (MPR) Card MPR Option Card KX-TDA0105 Memory Expansion Card (MEC) KX-TDA0196 Remote Card (RMT) CO Line Cards KX-TDA0180 8-Port Analog Trunk Card (LCOT8)
Page 3 KX-A258 Blank Slot Cover Equipment KX-T30865 Doorphone Available Proprietary Telephones The Hybrid IP-PBX supports all of the Panasonic KX-T7000, KX-TD7000, and KX-NT series: • Digital/Analog/IP proprietary telephones (e.g., KX-T7625, KX-T7630, KX-T7633, KX-T7636, KX- NT136) • Portable stations (e.g., KX-TD7690) •...
Page 4: Important Safety Instructions
Important Safety Instructions SAFETY REQUIREMENTS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: Read and understand all instructions. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning.
Page 5 Do not use the telephone to report a gas leak in the vicinity of the leak. SAVE THESE INSTRUCTIONS Installation Manual...
Page 6 Precaution WARNING REMOVE MEMORY CARD WHILE POWER SUPPLIED H Y B R I D I P - P B X Doing so may cause the Hybrid IP-PBX to fail to start when you try to restart the system. Installation Manual...
Page 7 If the telephone operates properly, do not reconnect the unit to the line until the trouble has been repaired by an authorized Panasonic Factory Service Centre. If the telephone does not operate properly, chances are that the trouble is in the telephone system, and not in the unit.
Page 8: Password Security
Password Security Warning to the Administrator or Installer regarding the system password Please provide all system passwords to the customer. To avoid unauthorized access and possible abuse of the PBX, keep the passwords secret, and inform the customer of the importance of the passwords, and the possible dangers if they become known to others.
Page 9 Executive or Regional Sales offices. They are NOT equipped to make repairs. Product Service Panasonic Factory Servicenters for this product are listed in the servicenter directory. Consult your certified Panasonic dealer for detailed instructions. The serial number of this product may be found on the label affixed to the side of the unit.
Page 10: About The Other Manuals
Introduction This Installation Manual is designed to serve as an overall technical reference for the Panasonic Hybrid IP- PBX, KX-TDA100/KX-TDA200. It provides instructions for installing the hardware, and programming the Hybrid IP-PBX using the KX-TDA Maintenance Console. The Structure of this Manual...
Page 11 • Telephone numbers to which the system will be connected • Make: Panasonic • Model: KX-TDA100 and KX-TDA200 • Certification No.: found on the side of the unit • Ringer Equivalence No.: 0.3A •...
Page 12 If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 13 For Cell Station CAUTION Any changes or modifications not expressly approved by the party responsible for compliance could void user's authority to operate this device. Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 14: Table Of Contents
2.2.8 Attaching a Ferrite Core ....................54 2.2.9 Fastening Amphenol Type Connector ................56 2.2.10 Wall Mounting (KX-TDA200) .....................58 2.2.11 Wall Mounting (KX-TDA100) .....................60 2.2.12 Floor Standing (KX-TDA200 Only) ..................62 2.2.13 Surge Protector Installation....................65 Installation of the Main Processing Card..............68 2.3.1 MPR Card .........................68 2.3.2...
Page 15 2.5.5 SLC8 Card ........................95 2.5.6 EXT-CID Card ........................97 2.5.7 SLC16 and MSLC16 Cards ....................98 2.5.8 IP-EXT16 Card ....................... 100 Installation of the Other Cards ..................102 2.6.1 OPB3 Card ........................102 2.6.2 DPH4 Card ........................103 2.6.3 EIO4 Card ........................
Page 16 Revision History......................186 5.1.1 Version 1.1 ........................186 5.1.2 Version 2.0 ........................187 Index ......................189 Installation Manual...
Page 17: System Outline
Section 1 System Outline This section provides general information on the Hybrid IP- PBX, including the system capacity and specifications. Installation Manual...
Page 18: System Highlights
PC Phone/PC Console These Panasonic CTI applications can be used on computers connected to each extension, providing their respective extension users with powerful and flexible call handling and display features.
Page 19: Voice Mail Features
Portable Station (PS) Features A Panasonic PS can be used in place of a PT to provide wireless access to PBX features and call handling. When in Wireless XDP Parallel Mode, a PS can share an extension number with a wired telephone, allowing extension users to use their PSs when they are away from their desks to answer or make calls as if they were using their wired telephones.
Page 20: Basic System Construction
1.2.1 Basic Shelf The basic shelf contains an MPR card. For system expansion, optional service cards and a power supply unit can be installed in the basic shelf. KX-TDA100 KX-TDA200 Construction of Basic Shelf A: Slots for Expansion B: MPR Card...
Page 21: System Connection Diagram
1.2 Basic System Construction 1.2.2 System Connection Diagram Private IP Network CO (Telephone Company) Lines Analog/PRI/T1 Remote PC Hybrid IP-PBX Router IP-PT Server PC Printer Fax Machine External Sensor/ External Relay Device Wireless Phone DSS Console Doorphone & Door Opener DSS Console BGM/Music On Hold (MOH) Pager/...
Page 22 1.2 Basic System Construction Hybrid IP-PBX KX-T7636/ KX-T7600 KX-T7600 KX-T7633 LCOT16 DLC16 (KX-TDA0181) (KX-TDA0172) LCOT8 DLC8 Voice (KX-TDA0180) (KX-TDA0171) Processing Analog System Analog Analog CID8 DSS Console PT-interface CS (KX-TDA0193) CO Line CO Line CO Line Telephone ISDN PRI Line ISDN PRI Line ISDN PRI Line Company...
Page 23: Options
1.3 Options Options 1.3.1 Options Model No. Model Name Description KX-TDA0105 Memory Expansion Card Memory expansion card to increase system data storage (MEC) space, enable Broadcasting feature, and double the number of DPTs, using Digital XDP connection. To be mounted on the MPR card.
Page 24 Power Supply Unit for KX-TDA100 and KX-TDA200. Total (PSU-M) power output of 140.4 W. Safety Class 1 compliant. KX-TDA0108 S-Type Power Supply Unit Power Supply Unit for KX-TDA100. Total power output of 74 (PSU-S) W. Safety Class 1 compliant. KX-TDA0920 SD Memory Card for Software...
Page 25: Specifications
100 V AC to 130 V AC, 5.1 A/200 V AC to 240 V AC, 2.55 A, 50 Hz/60 Hz 300 ms Maximum Power Failure Tolerance Power KX-TDA100 140 W, 1.4 A (at 120 V AC, 60 Hz) Consumption with PSU-S KX-TDA100 210 W, 2.2 A (at 120 V AC, 60 Hz)
Page 26 1-pair wire (D1, D2) DSS Console and Add-on Key Module 1-pair wire (D1, D2) Dimension KX-TDA100 334 mm (W) × 390 mm (H) × 270 mm (D) (13-1/3 in × 15-3/5 in × 10-4/5 in) KX-TDA200 430 mm (W) × 415 mm (H) × 270 mm (D) (17-1/5 in ×...
Page 27: Characteristics
1.4 Specifications 1.4.2 Characteristics PT: KX-T7600 series: 90 Ω; all other DPTs/APTs: 40 Ω Terminal Equipment Loop Limit • SLT: 600 Ω including set • Doorphone: 20 Ω • CS: 130 Ω; PT-interface CS: 65 Ω • 15 000 Ω minimum Minimum Leakage Resistance Maximum Number of Extension 1 for PT or SLT...
Page 28: System Capacity
Any card that exceeds the capacity of the Hybrid IP-PBX will be ignored. • When the Hybrid IP-PBX starts up with an invalid configuration, some cards will be ignored. Cards Installed in the Slots of the Hybrid IP-PBX KX-TDA100 KX-TDA200 MPR Card Slot MPR Card Slot...
Page 29 1.4 Specifications The following number of optional service cards can be installed in the various slots of the Hybrid IP-PBX. Maximum Number Card Type Installed in KX-TDA100 KX-TDA200 MPR Card Slot Trunk Card Total 4 Total 8 LCOT4 LCOT8 LCOT16...
Page 30: Cards Mounted On Other Optional Service Cards
Cards Mounted on Other Optional Service Cards The following number of optional service cards can be mounted on the specified other optional service cards. Maximum Number Card Type Mounted on KX-TDA100 KX-TDA200 MPR Card CID8 LCOT8 Card/LCOT16 Card EXT-CID SLC8 Card...
Page 31: Mec Card Calculation
MEC Card Calculation Calculate the MEC figure from the type and total number of items of equipment to be connected. If the MEC figure exceeds 64 (for KX-TDA100) or 128 (for KX-TDA200), you need to install an MEC card. MEC Card Calculation...
Page 32: Power Supply Unit Selection
Each PSU supports a different amount of load figures. PSU Type Maximum Load Figures PSU-S PSU-M PSU-L Available for the KX-TDA100 Available for the KX-TDA100 and KX-TDA200 Available for the KX-TDA200 Calculation Example (KX-TDA200) Equipment Type Load Figure KX-T7600 series DPT 48 units...
Page 33 1.4 Specifications Equipment Type Load Figure Total The total load figure is 96. As this is between 64 and 128, you should install the PSU-M. However, if you expect expansion in the future, it may be better to install the PSU-L. There is no harm in installing a PSU that is larger than is required for the current configuration.
Page 34 1.4 Specifications Installation Manual...
Page 35: Installation
Section 2 Installation This section describes the procedures to install the Hybrid IP- PBX. Detailed instructions for planning the installation site, installing the shelves and optional service cards, and cabling of peripheral equipment are provided. Further information on system expansion and peripheral equipment installation is included.
Page 36: Before Installation
Anti-static precautions should be taken during installation. Installation Precautions This set is made for wall mounting (KX-TDA100/KX-TDA200) or floor standing (KX-TDA200 only). Avoid installing in the following places. (Doing so may result in malfunction, noise, or discoloration.) In direct sunlight and hot, cold, or humid places.
Page 37 2.1 Before Installation Avoid using the same power supply outlet for computers, telexes, and other office equipment. Otherwise, Hybrid IP-PBX operation may be interrupted by the induction noise from such equipment. Please use 1-pair telephone wire for extension connection of (telephone) equipment such as standard telephones, data terminals, answering machines, computers, Voice Processing Systems, etc., except PTs (e.g., KX-T7600 series).
Page 38: Installation Of The Hybrid Ip-Pbx
2.2 Installation of the Hybrid IP-PBX Installation of the Hybrid IP-PBX 2.2.1 Unpacking Unpack the box and check the items below: KX-TDA100 KX-TDA200 Main Unit Metal Bracket Screw A Screw B (Black) Anchor Plug Mini Plug (for pager and music source)
Page 39: Names And Locations
2.2 Installation of the Hybrid IP-PBX 2.2.2 Names and Locations Inside View KX-TDA100 KX-TDA200 RS-232C Port RS-232C Port USB Port USB Port ALARM Indicator ALARM Indicator RUN Indicator RUN Indicator PSU Slot PSU Slot MPR Card Slot MPR Card Slot...
Page 40: Opening/Closing The Front Cover
2.2 Installation of the Hybrid IP-PBX 2.2.3 Opening/Closing the Front Cover Opening the Front Cover Insert a flathead screwdriver into the opening (on the left of the screw cover) and unlatch the screw cover. Screw Cover Turn the screw counterclockwise to loosen. Slide the front cover to the right until it stops, then lift the front cover.
Page 41: Closing The Front Cover
2.2 Installation of the Hybrid IP-PBX Closing the Front Cover Hook the front cover onto the cabinet (line up the protrusions on the cover with the receptacles on the cabinet). Then slide the front cover to the left until it locks. Turn the screw clockwise to tighten.
Page 42: Installing/Replacing The Power Supply Unit
Lower/Upper Input Voltage Range Current Input Frequency PSU-S Lower: 100 V AC to 130 V AC 1.4 A (for KX-TDA100) Upper: 200 V AC to 240 V AC 0.8 A PSU-M Lower: 100 V AC to 130 V AC 2.5 A...
Page 43 2.2 Installation of the Hybrid IP-PBX To protect the back board from static electricity, do not touch parts on the back board in the main unit and PSU. To discharge static electricity, touch ground or wear a grounding strap. The following procedures are for installing or replacing a PSU only. Do not replace or remove the PSU for any other purpose.
Page 44: Replacing The Power Supply Unit
2.2 Installation of the Hybrid IP-PBX Turn the 4 screws clockwise, in the order indicated by the numbers 1 to 4, to fix the PSU. Screws Replacing the Power Supply Unit Unplug the AC power cord. Turn the 4 screws counterclockwise to loosen them. Screws Installation Manual...
Page 45 2.2 Installation of the Hybrid IP-PBX Pull the release lever in the direction of the arrow to disconnect the PSU from the back board. Back Board Release Lever Replace the PSU. New PSU Current PSU Follow the steps in "Installing the Power Supply Unit". Installation Manual...
Page 46: Frame Ground Connection
2.2 Installation of the Hybrid IP-PBX 2.2.5 Frame Ground Connection IMPORTANT Connect the frame of the Hybrid IP-PBX to earth. Loosen the screw. Screw Insert a grounding wire (user- supplied)*. Tighten the screw. Connect the grounding wire to Grounding earth. wire To Ground * For grounding wire, green-and-yellow insulation is required, and the cross-sectional area of the...
Page 47: Installing/Removing The Optional Service Cards
2.2 Installation of the Hybrid IP-PBX 2.2.6 Installing/Removing the Optional Service Cards CAUTION To protect the back board from static electricity, do not touch parts on the back board in the main unit and on the optional service cards. To discharge static electricity, touch ground or wear a grounding strap.
Page 48 2.2 Installation of the Hybrid IP-PBX Holding the card as shown below, push the release lever in the direction of the arrow so that the card engages securely with the connector on the back board. Back Board Release Lever Turn the 2 screws clockwise to fix the card in place. Screws Note Make sure the screws are tightened to ground the card securely.
Page 49: Covering The Blank Slots
2.2 Installation of the Hybrid IP-PBX Covering the Blank Slots Be sure to cover each slot in which no optional service card is installed by using a Blank Slot Cover. CAUTION Failure to install the Blank Slot Cover may cause electromagnetic interferences. Installation Manual...
Page 50: Handling Of The Cables
2.2 Installation of the Hybrid IP-PBX Handling of the Cables When cables are connected to the Hybrid IP-PBX, run the cables to either right or left and then towards the backside of the cabinet as shown below. Note For safety reasons, do not stretch, bend, or pinch the AC power cord. Installation Manual...
Page 51 2.2 Installation of the Hybrid IP-PBX Removing the Optional Service Cards Turn the 2 screws counterclockwise to loosen them. Screws Pull the release lever in the direction of the arrow to disconnect the card from the back board. Pull the card from the cabinet to remove it.
Page 52: Types Of Connectors
2.2 Installation of the Hybrid IP-PBX 2.2.7 Types of Connectors Connector Type Pin Number Used for • DHLC8 (KX-TDA0170) RJ11 • SLC8 (KX-TDA0173) • SLC16 (KX-TDA0174) • MSLC16 (KX-TDA0175) • LCOT8 (KX-TDA0180) • LCOT16 (KX-TDA0181) (Twisted pair cable) • CSIF4 (KX-TDA0143) RJ45 •...
Page 53 2.2 Installation of the Hybrid IP-PBX Connector Type Pin Number Used for • IP-GW4 (KX-TDA0480) RS-232C • Basic Shelf • • Mini Plug Installation Manual...
Page 54: Attaching A Ferrite Core
2.2 Installation of the Hybrid IP-PBX 2.2.8 Attaching a Ferrite Core A ferrite core must be attached when: • connecting IP-GW16 and IP-EXT16 cards using an RJ45 connector, or • connecting extension cards using an Amphenol connector. The ferrite core is included with the card. When connecting an IP-GW16/IP-EXT16 card Wrap the cable once around the ferrite core, then close the case of the ferrite core.
Page 55 2.2 Installation of the Hybrid IP-PBX If you need to open the ferrite core, use a flathead screwdriver to unlatch the case of the ferrite core. Installation Manual...
Page 56: Fastening Amphenol Type Connector
2.2 Installation of the Hybrid IP-PBX 2.2.9 Fastening Amphenol Type Connector An Amphenol 57JE type connector is used on some of the optional service cards. To connect an Amphenol connector, use the spring latch or screw to fix the upper part and use Velcro® tape to fix the lower part of the connector.
Page 57: Amphenol Connector Pin Assignment Chart
2.2 Installation of the Hybrid IP-PBX Amphenol Connector Pin Assignment Chart Below is an Amphenol connector pin assignment chart for all optional service cards that use the Amphenol connector. For more details, refer to the appropriate section in "2.4 Installation of the CO Line Cards" and "2.5 Installation of the Extension Cards".
Page 58: Wall Mounting (Kx-Tda200)
2.2 Installation of the Hybrid IP-PBX 2.2.10 Wall Mounting (KX-TDA200) CAUTION Drive mounting screws into the wall. Be careful to avoid touching any metal laths, wire laths or metal plates in the wall. Install 4 anchor plugs in the wall, using the metal bracket as a template. Fix the metal bracket with 4 screws (A).
Page 59 2.2 Installation of the Hybrid IP-PBX Hook the cabinet onto the metal bracket, making sure that the unit slides down and onto the hooked parts of the metal bracket. Use 2 screws (B) to fix both sides of the cabinet. Screw (B) Notes •...
Page 60: Wall Mounting (Kx-Tda100)
2.2 Installation of the Hybrid IP-PBX 2.2.11 Wall Mounting (KX-TDA100) CAUTION Drive mounting screws into the wall. Be careful to avoid touching any metal laths, wire laths or metal plates in the wall. Install 3 anchor plugs in the wall, using the metal bracket as a template. Fix the metal bracket with 3 screws (A).
Page 61 2.2 Installation of the Hybrid IP-PBX Hook the cabinet onto the metal bracket, making sure that the unit slides down and onto the hooked parts of the metal bracket. Use 2 screws (B) to fix both sides of the cabinet. Screw (B) Notes •...
Page 62: Floor Standing (Kx-Tda200 Only)
2.2 Installation of the Hybrid IP-PBX 2.2.12 Floor Standing (KX-TDA200 Only) Install 4 anchor plugs in the floor, using the metal bracket as a template. Fix the metal bracket with 4 screws (A). Screw (A) Metal Bracket Screw (A) Hammer Anchor Metal Plug...
Page 63 2.2 Installation of the Hybrid IP-PBX Lift the cabinet, attach it to the metal bracket, slide it backwards until it locks, and retain it with 2 screws (B). FRONT Screws (B) Metal Bracket Notes • Do not block the openings of the cabinet. Allow space of at least 20 cm (8 in) above and 10 cm (4 in) at the sides of the cabinet.
Page 64 2.2 Installation of the Hybrid IP-PBX • Make sure that the surface behind the cabinet is not made of wood. • Be careful not to drop the cabinet. Fix the front cover on the cabinet (refer to "2.2.3 Opening/Closing the Front Cover"). Installation Manual...
Page 65: 2.2.13 Surge Protector Installation
2.2 Installation of the Hybrid IP-PBX 2.2.13 Surge Protector Installation Overview A massive electrical surge can be caused if lightning strikes a telephone cable 10 m (33 ft) above ground, or if a telephone line comes into contact with a power line. A surge protector is a device that is connected to a CO line to prevent potentially dangerous electrical surges from entering the building via the CO line and damaging the Hybrid IP-PBX and connected equipment.
Page 66 2.2 Installation of the Hybrid IP-PBX Outside Installation (Main Building) Surge Protector CO Line (Another Building) CO Line Extn. Hybrid Terminal IP-PBX Board Surge Extn. Protector Extn. Extn. Earth Extn.: Extension Line If you install an extension outside of the building, the following precautions are recommended: Install the extension wire underground.
Page 67 2.2 Installation of the Hybrid IP-PBX Connect the earth rod to the surge protector using an earthing wire with a cross-sectional area of at least 1.3 mm Bury the earth rod near the protector. The earthing wire should be as short as possible. The earthing wire should run straight to the earth rod.
Page 68: Installation Of The Main Processing Card
For details about Reset Button, refer to "4.1.4 Using the Reset Button". CAUTION • Use only the SD Memory Card included with the Hybrid IP-PBX, or a Panasonic optional upgrade SD Memory Card. • The SD Memory Card contains software for all processes of the Hybrid IP-PBX and all customer data.
Page 69: Led Indications
2.3 Installation of the Main Processing Card • A LITHIUM BATTERY IS USED IN THE MPR CARD. THERE IS A RISK OF EXPLOSION IF BATTERY IS REPLACED WITH THE INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. LED Indications Indication Color Description...
Page 70: Mec Card
2.3 Installation of the Main Processing Card 2.3.2 MEC Card Function Memory expansion card to increase system data storage space, enable Broadcasting feature, and double the number of DPTs, using Digital XDP connection. To be mounted on the MPR card. inside Screw MEC Card...
Page 71: Rmt Card
2.3 Installation of the Main Processing Card 2.3.3 RMT Card Function Analog modem card for remote communication with the Hybrid IP-PBX. ITU-T V.90 support. To be mounted on the MPR card. inside Screw RMT Card Accessory and User-supplied Items Accessory (included): Screws × 2 User-supplied (not included): none Installation Manual...
Page 72: Installation Of The Co Line Cards
2.4 Installation of the CO Line Cards Installation of the CO Line Cards 2.4.1 LCOT8 and LCOT16 Cards Function LCOT8: 8-port analog CO line card with 2 power failure transfer (PFT) ports. One CID8 card can be mounted on the LCOT8 card (refer to "2.4.2 CID8 Card"). LCOT16: 16-port analog CO line card with 4 power failure transfer (PFT) ports.
Page 73 2.4 Installation of the CO Line Cards Pin Assignments Amphenol Connector Signal Name Function Signal Name Function Ring port 1 Tip port 1 Ring port 2 Tip port 2 Ring port 3 Tip port 3 Ring port 4 Tip port 4 Ring port 5 Tip port 5 Ring port 6...
Page 74: Cid8 Card
2.4 Installation of the CO Line Cards 2.4.2 CID8 Card Function 8-port Caller ID signal type FSK/FSK (with Call Waiting Caller ID [Visual Caller ID])/DTMF. To be mounted on the LCOT8/LCOT16 cards. inside CID8 Card Screw Accessory and User-supplied Items Accessory (included): Screws ×...
Page 75: T1 Card
2.4 Installation of the CO Line Cards 2.4.3 T1 Card Function 1-port T1 CO line card. EIA/TIA standard compliant. LEDs RJ45 To NT1 Accessory and User-supplied Items Accessory (included): none User-supplied (not included): RJ45 connector Notes • Connect this optional service card to the CO line through NT1; do not connect to the CO line directly.
Page 76 2.4 Installation of the CO Line Cards Pin Assignments RJ45 Connector Signal Name Level [V] Function Receive data (+) Receive data (-) Reserved – – Transmit data (-) Transmit data (+) Reserved – – LED Indications Indication Color Description CARD STATUS Green/Red Card status indication •...
Page 77: Pri23 Card
2.4 Installation of the CO Line Cards 2.4.4 PRI23 Card Function 1-port ISDN Primary Rate Interface card (23B channels). NI (North American standard ISDN protocol) compliant. LEDs RJ45 Accessory and User-supplied Items Accessory (included): none User-supplied (not included): RJ45 connector Notes •...
Page 78 2.4 Installation of the CO Line Cards Pin Assignments RJ45 Connector Signal Name Level [V] Function Receive data (+) Receive data (-) Reserved – – Transmit data (-) Transmit data (+) Reserved – – LED Indications Indication Color Description CARD STATUS Green/Red Card status indication •...
Page 79: Ip-Gw4 Card
2.4 Installation of the CO Line Cards 2.4.5 IP-GW4 Card Function 4-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729a, and G.723.1 CODEC methods. G3 fax support. LEDs RJ45 (10BASE-T) To private IP network Accessory and User-supplied Items Accessory (included): CD-ROM (including PC programming software and documentation) ×...
Page 80 2.4 Installation of the CO Line Cards LED Indications Indication Color Description CARD STATUS Green/Red Card status indication • OFF: Power Off • Green ON: Normal (all ports are idle) • Green Flashing (60 times per minute): Normal (a port is in use) •...
Page 81: Ip-Gw4E Card
2.4 Installation of the CO Line Cards 2.4.6 IP-GW4E Card Function 4-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729a, G.723.1, and G.711 CODEC methods. LEDs RJ45 (10BASE-T/100BASE-TX) To private IP network Accessory and User-supplied Items Accessory (included): CD-ROM (including documentation for web programming) ×...
Page 82 2.4 Installation of the CO Line Cards LED Indications Indication Color Description CARD STATUS Green/Red Card status indication • OFF: Power Off • Green ON: Normal (all ports are idle) • Green Flashing (60 times per minute): Normal (a port is in use) •...
Page 83: Ip-Gw16 Card
2.4 Installation of the CO Line Cards 2.4.7 IP-GW16 Card Function 16-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729a, G.723.1, and G.711 CODEC methods. LEDs RJ45 (10BASE-T/100BASE-TX Full Duplex) To private IP network Accessory and User-supplied Items Accessory (included): Ferrite core ×...
Page 84 2.4 Installation of the CO Line Cards LED Indications Indication Color Description CARD STATUS Green/Red Card status indication • OFF: Power Off • Green ON: Normal (all ports are idle) • Green Flashing (60 times per minute): Normal (a port is in use) •...
Page 85: Installation Of The Extension Cards
2.5 Installation of the Extension Cards Installation of the Extension Cards 2.5.1 CSIF4 and CSIF8 Card Function CSIF4: 4-port CS interface card for 4 CSs. CSIF8: 8-port CS interface card for 8 CSs. RJ45 (LINE 1 to LINE 8) To CS Accessory and User-supplied Items Accessory (included): none User-supplied (not included): RJ45 connector...
Page 86 2.5 Installation of the Extension Cards Editing the CS Name using the KX-TDA Maintenance Console While programming the Hybrid IP-PBX, we strongly recommend that you input a unique recognizable CS name (maximum 20 characters) for each CS port in use, and "(Reserved)" or "(Not for CSIF4)" for unused ports or unavailable ports respectively for the following reasons: you will be able to easily distinguish installed CSs.
Page 87 2.5 Installation of the Extension Cards LED Indications Indication Color Description CARD STATUS Green/Red Card status indication • OFF: Power Off • Green ON: Normal (all ports are idle) • Green Flashing (60 times per minute): Normal (a port is in use) •...
Page 88: Dhlc8 Card
2.5 Installation of the Extension Cards 2.5.2 DHLC8 Card Function 8-port digital hybrid extension card for DPTs, APTs, SLTs, DSS consoles, and PT-interface CSs, with 2 power failure transfer (PFT) ports. Amphenol To extensions Accessory and User-supplied Items Accessory (included): Screws × 2, Ferrite core × 1 User-supplied (not included): Amphenol connector Notes •...
Page 89 2.5 Installation of the Extension Cards Pin Assignments Amphenol Connector No. Signal Name Function No. Signal Name Function SLT Ring port 1 SLT Tip port 1 PT Data port 1 (Low) PT Data port 1 (High) Reserved – Reserved – SLT Ring port 2 SLT Tip port 2 PT Data port 2 (Low)
Page 90 2.5 Installation of the Extension Cards LED Indications Indication Color Description CARD STATUS Green/ Card status indication Orange/Red • OFF: Power Off • Green ON: Normal (all ports are idle) • Green Flashing (60 times per minute): Normal (a port is in use) •...
Page 91: Dlc8 Card
2.5 Installation of the Extension Cards 2.5.3 DLC8 Card Function 8-port digital extension card for DPTs, DSS consoles, and PT-interface CSs. Amphenol To extensions Accessory and User-supplied Items Accessory (included): Screws × 2, Ferrite core × 1 User-supplied (not included): Amphenol connector Notes •...
Page 92 2.5 Installation of the Extension Cards Pin Assignments Amphenol Connector Signal Name Function Signal Name Function Reserved – Reserved – Data port 1 (Low) Data port 1 (High) Reserved – 28-29 Reserved – Data port 2 (Low) Data port 2 (High) Reserved –...
Page 93: Dlc16 Card
2.5 Installation of the Extension Cards 2.5.4 DLC16 Card Function 16-port digital extension card for DPTs, DSS consoles, and PT-interface CSs. Amphenol To extensions Accessory and User-supplied Items Accessory (included): Screws × 2, Ferrite core × 1 User-supplied (not included): Amphenol connector Notes •...
Page 94 2.5 Installation of the Extension Cards Pin Assignments Amphenol Connector Signal Name Function Signal Name Function Data port 1 (Low) Data port 1 (High) Data port 2 (Low) Data port 2 (High) Data port 3 (Low) Data port 3 (High) Data port 4 (Low) Data port 4 (High) Data port 5 (Low)
Page 95: Slc8 Card
2.5 Installation of the Extension Cards 2.5.5 SLC8 Card Function 8-port extension card for SLTs with 2 power failure transfer (PFT) ports. Amphenol To extensions Accessory and User-supplied Items Accessory (included): Screws × 2, Ferrite core × 1 User-supplied (not included): Amphenol connector Notes •...
Page 96 2.5 Installation of the Extension Cards Pin Assignments Amphenol Connector Signal Name Function Signal Name Function Ring port 1 Tip port 1 Reserved – 27-28 Reserved – Ring port 2 Tip port 2 Reserved – 30-31 Reserved – Ring port 3 Tip port 3 Reserved –...
Page 97: Ext-Cid Card
2.5 Installation of the Extension Cards 2.5.6 EXT-CID Card Function Sends Caller ID signals to extension ports. To be mounted on the SLC8 card. inside SLC8 Card Screw EXT-CID Card Accessory and User-supplied Items Accessory (included): Screws × 2 User-supplied (not included): none Installation Manual...
Page 98: Slc16 And Mslc16 Cards
Accessory (included): Screws × 2, Ferrite core × 1 User-supplied (not included): Amphenol connector Notes • Panasonic SLT with Message Waiting Lamp (e.g., KX-T7310) is recommended for connection to the MSLC16 card. • Attach the included ferrite core to the cable. Refer to "2.2.8 Attaching a Ferrite Core".
Page 99 2.5 Installation of the Extension Cards Pin Assignments Amphenol Connector Signal Name Function Signal Name Function Ring port 1 Tip port 1 Ring port 2 Tip port 2 Ring port 3 Tip port 3 Ring port 4 Tip port 4 Ring port 5 Tip port 5 Ring port 6...
Page 100: Ip-Ext16 Card
2.5 Installation of the Extension Cards 2.5.8 IP-EXT16 Card Function 16-channel VoIP extension card. Compliant with Panasonic proprietary protocol, and ITU-T G.729a and G.711 CODEC methods. LEDs RJ45 (100BASE-TX Full Duplex) To private IP network Accessory and User-supplied Items Accessory (included): Ferrite core × 1...
Page 101 If the LINK indicator is OFF, the ONLINE indicator will also be OFF. ALARM Alarm indication • OFF: Normal • ON: Alarm VoIP BUSY Green Panasonic proprietary VoIP protocol process indication • OFF: VoIP process inactive • ON: VoIP process active LINK Green Link status indication • OFF: Connection error •...
Page 102: Installation Of The Other Cards
2.6 Installation of the Other Cards Installation of the Other Cards 2.6.1 OPB3 Card Function Optional 3-slot base card for mounting a maximum of 3 option cards from the following: • DPH4 card • EIO4 card • ECHO16 card • MSG4 card CAUTION A LITHIUM BATTERY IS USED IN OPB3 CARD.
Page 103: Dph4 Card
2.6 Installation of the Other Cards 2.6.2 DPH4 Card Function 4-port doorphone card for 4 doorphones and 4 door openers. To be mounted on the OPB3 card. Fully insert the connectors through the panel openings. DPH4 Card OPB3 Card 8-pin Screw 10-pin Accessory and User-supplied Items...
Page 104 2.6 Installation of the Other Cards Pin Assignments 8-pin Terminal Block Signal Name Function Doorphone 4 transmit com4 Doorphone 4 receive Doorphone 3 transmit com3 Doorphone 3 receive Doorphone 2 transmit com2 Doorphone 2 receive Doorphone 1 transmit com1 Doorphone 1 receive 10-pin Terminal Block Signal Name Function...
Page 105: Eio4 Card
2.6 Installation of the Other Cards 2.6.3 EIO4 Card Function 4-port external input/output card. To be mounted on the OPB3 card. Fully insert the connectors through the panel openings. EIO4 Card OPB3 Card 8-pin Screw 10-pin Accessory and User-supplied Items Accessory (included): Screws ×...
Page 106 2.6 Installation of the Other Cards Pin Assignments 8-pin Terminal Block Signal Name Function Control 4 Control 4 com Control 3 Control 3 com Control 2 Control 2 com Control 1 Control 1 com 10-pin Terminal Block Signal Name Function Reserved –...
Page 107: Connection Diagram For External Sensor
2.6 Installation of the Other Cards Connection Diagram for External Sensor Power to the external sensor is provided from the EIO4 card and must be grounded through the EIO4 card as indicated in the diagram below. A pair of "sensor" and "common" lines are connected to the EIO4 card for each external sensor.
Page 108: Echo16 Card
2.6 Installation of the Other Cards 2.6.4 ECHO16 Card Function 16-channel card for echo cancellation during conferences. To be mounted on the OPB3 card. OPB3 Card inside ECHO16 Card Screw Accessory and User-supplied Items Accessory (included): Screws × 3 User-supplied (not included): none Note To establish a conference call involving 6 to 8 parties, install an ECHO16 card and enable the echo cancellation for conference using the KX-TDA Maintenance Console.
Page 109: Msg4 Card
2.6 Installation of the Other Cards 2.6.5 MSG4 Card Function 4-channel message card. To be mounted on the OPB3 card. OPB3 Card inside MSG4 Card Screw Accessory and User-supplied Items Accessory (included): Screws × 3 User-supplied (not included): none Installation Manual...
Page 110: Cti-Link Card
2.6 Installation of the Other Cards 2.6.6 CTI-LINK Card Function Ethernet card for CTI communication via 10BASE-T port. CSTA Phase 3 protocol compatible. LEDs RJ45 (10BASE-T) To LAN/ Server PC Accessory and User-supplied Items Accessory (included): none User-supplied (not included): RJ45 connector Notes •...
Page 111 2.6 Installation of the Other Cards LED Indications Indication Color Description CARD STATUS Green/Red Card status indication • OFF: Power Off • Green ON: Normal • Red ON: Fault (includes reset) • Red Flashing (60 times per minute): Out of Service LINK STATUS Green Link status indication...
Page 112: Connection Of Extensions
2.7 Connection of Extensions Connection of Extensions 2.7.1 Maximum Cabling Distances of the Extension Wiring (Twisted Cable) Cable Maximum Distance PT-interface CS 26 AWG: Under 222 m (728 ft) 24 AWG: Under 347 m (1138 ft) 22 AWG: Under 500 m (1640 ft) CAT 5: Under 347 m (1138 ft) KX-T7600 Series *...
Page 113 2.7 Connection of Extensions PT-interface CS DSS Console DHLC8 Card MSLC16, SLC16, SLC8 Cards DLC16, DLC8 Cards " " indicates that the extension card is available for the terminal. Installation Manual...
Page 114: Parallel Connection Of The Extensions
2.7 Connection of Extensions 2.7.2 Parallel Connection of the Extensions Any SLT can be connected in parallel with an APT or a DPT as follows. Note In addition to an SLT, an answering machine, a fax machine or a modem (PC) can be connected in parallel with an APT or a DPT.
Page 115 2.7 Connection of Extensions Using an EXtra Device Port With KX-T7600 Series DPT To DHLC8 card 2-conductor wiring cord 4-conductor wiring cord Connect pins "T" and "R". Connect pins "T", "R", "D1" and "D2". TO MAIN UNIT / PABX TO TEL To DHLC8 card To SLT With Other DPT...
Page 116: Digital Extra Device Port (Digital Xdp) Connection
2.7 Connection of Extensions 2.7.3 Digital EXtra Device Port (Digital XDP) Connection A DPT can be connected to another DPT on the Digital XDP connection. In addition, if the DPT is connected to a DHLC8 card, it can also have an SLT connected in Parallel mode or XDP mode. Notes •...
Page 117 2.7 Connection of Extensions Using an EXtra Device Port To DLC8/DLC16 card 4-conductor wiring cord To DHLC8 card Connect pins "T", "R", 2-conductor wiring cord (for connection of SLT) "D1" and "D2". Connect pins "T" and "R". 4-conductor wiring cord Connect pins "T", "R", "D1"...
Page 118: First Party Call Control Cti Connection
2.7 Connection of Extensions 2.7.4 First Party Call Control CTI Connection CTI connection between a PC and a KX-T7633/T7636 DPT provides the first party call control. The CTI connection is made via USB interface (version 1.1), and uses the TAPI 2.1 protocol. A USB Module (KX-T7601) must be connected to the KX-T7633/T7636 DPT.
Page 119: Connection Of 2.4 Ghz Portable Stations
This unit determines the area covered by the wireless system. Up to 2 calls can be made at the same time through each CS. PS: 2.4 GHz Portable Station (KX-TD7680/KX-TD7690) The KX-TDA100 and KX-TDA200 can support up to 128 PSs. For more details about the PS, refer to the PS Operating Instructions. CAUTION •...
Page 120 2.8 Connection of 2.4 GHz Portable Stations Please take into consideration the distance between the CSs when site planning. Please consult a certified dealer for details. However, the required distance between CSs may vary depending on the environment of the installation site and conditions in which the wireless system is used.
Page 121: Procedure Overview
2.8 Connection of 2.4 GHz Portable Stations 2.8.2 Procedure Overview When connecting the wireless system, use extreme care to conduct a site survey. Inadvertent site survey can result in narrow service area, frequent noise, and disconnection of calls. 1. Investigate the installation site Refer to "2.8.3 Site Planning".
Page 122 2.8 Connection of 2.4 GHz Portable Stations 4. Finish the site survey Refer to "2.8.6 After Site Survey". Return all DIP switches of each CS to the OFF position, and stop supplying electricity. Turn off the PS. 5. Connect the CS and PS to the Hybrid IP-PBX and test the operation Refer to "2.8.7 Connecting a Cell Station to the Hybrid IP-PBX".
Page 123: Site Planning
2.8 Connection of 2.4 GHz Portable Stations 2.8.3 Site Planning Choosing the best site for the CS requires careful planning and testing of essential areas. The best location may not always be convenient for installation. Read the following information before installing the unit. Understanding the Radio Waves Characteristics of Radio Waves The transmission of radio waves and the CS coverage area depend on the structure and materials of the...
Page 124 2.8 Connection of 2.4 GHz Portable Stations Object Material Transmission Tendency Wall Concrete The thicker they are, the less radio waves penetrate them. Ferroconcrete Radio waves can penetrate them, but the more iron there is, the more radio waves are reflected. Window Glass Radio waves usually penetrate them.
Page 125 2.8 Connection of 2.4 GHz Portable Stations CS Coverage Area The example below shows the size of the coverage area of 1 CS if it is installed where there is no obstacle. Note Radio signal strength levels are measured during the site survey (refer to "2.8.5 Site Survey"). Coverage Area Radio signal strength level is greater than "3".
Page 126 2.8 Connection of 2.4 GHz Portable Stations one CS becomes weak. However, if a PS moves away from a CS and there are no CSs available for handover, the PS may go out of range and the call could be lost. If the signal from the CS fades, due to the structure of the building, there may be some handover delay.
Page 127: Before Site Survey
2.8 Connection of 2.4 GHz Portable Stations 2.8.4 Before Site Survey Setting and Installing the CS Temporarily for Site Survey Switch the Radio Signal Test switch from OFF to ON. Set the CS number switches as desired. DIP Switch CS Number Switch Radio Signal Test Switch CS no.
Page 128 2.8 Connection of 2.4 GHz Portable Stations After setting the DIP switch, connect an AC adaptor or battery box to the CS using a power supply adaptor. Note The AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become disconnected.
Page 129: Site Survey
2.8 Connection of 2.4 GHz Portable Stations 2.8.5 Site Survey The PS has a Radio Signal Test mode that monitors the state of the radio link to the CS. After installing the CSs temporarily, set the PS to the Radio Signal Test mode and measure each CS coverage area. Then, record the results on the map of the installation site.
Page 130 2.8 Connection of 2.4 GHz Portable Stations Measure the radio signal strength by moving to and away from the CS. Move to the CS until the point the radio signal strength level becomes "12". Move away from the CS and identify the CS coverage area within which the radio signal strength level is greater than "8".
Page 131 2.8 Connection of 2.4 GHz Portable Stations Overlap the CS coverage areas of at least 2 CSs at any location in the installation site. CS no. 1 CS no. 2 CS no. 3 CS no. 4 Make sure that the radio signal strength level is greater than "3" at any location in the service area demanded by the user.
Page 132 2.8 Connection of 2.4 GHz Portable Stations Deleting the Stored Scan Data Using the KX-TD7680 Scan Data No. Press 1, 9, and POWER 0 to 9, or # for all data for more than 2 seconds. To the Desired Scan Data No. Using the KX-TD7690 Scan Data No.
Page 133: After Site Survey
2.8 Connection of 2.4 GHz Portable Stations 2.8.6 After Site Survey After obtaining the proper measurement results, exit the Radio Signal Test mode before connecting the CS to the Hybrid IP-PBX. Keep pressing POWER button on the PS until the PS is turned OFF. Disconnect the AC adaptor or battery box from the CS and stop supplying electricity.
Page 134: Connecting A Cell Station To The Hybrid Ip-Pbx
2.8 Connection of 2.4 GHz Portable Stations 2.8.7 Connecting a Cell Station to the Hybrid IP-PBX Using a CSIF Card Refer to the following example to connect a CS to the Hybrid IP-PBX. CSIF8 Card Port 1 Cable Maximum Distance 26 AWG: Under 444 m (1457 ft) 24 AWG:...
Page 135: Using A Dhlc/Dlc Card
2.8 Connection of 2.4 GHz Portable Stations Using a DHLC/DLC Card Refer to the following example to connect a CS to the Hybrid IP-PBX. DHLC8 Card Cable Maximum Distance 26 AWG: Under 222 m (728 ft) 24 AWG: Under 347 m (1138 ft) 22 AWG: Under 500 m (1640 ft) CAT 5:...
Page 136 2.8 Connection of 2.4 GHz Portable Stations Connecting the CS Connect the cable from the CSIF/DHLC/DLC card to the CS. Modular To CSIF/DHLC/DLC card Pass the cable through the groove of the CS (in any direction depending on your convenience). TO MAIN UNIT / PABX To CSIF/DHLC/DLC card...
Page 137 2.8 Connection of 2.4 GHz Portable Stations Registering the PS The PS must be registered to the Hybrid IP-PBX before it can be used. Programming of both the PS and Hybrid IP-PBX is required. A PT with multiline display (e.g., KX-T7636 6-line display) is required for the Hybrid IP-PBX system programming.
Page 138 2.8 Connection of 2.4 GHz Portable Stations PS Registration [690] PS No. Extn. No. To the PS operation 001 to 128 1 to 4 digits below ENTER ENTER When the PS has not been registered yet When registering the PS for the first time, it is possible to select the desired language for the display. (You do not need to enter the PS system programming mode when registering for the first time.) Using the KX-TD7680 [ F2 ]...
Page 139 2.8 Connection of 2.4 GHz Portable Stations Setting the System Lock When a system lock has been set, the system lock password will be required for PS system setting. Using the KX-TD7680 Choose Select "Enable/Disable". "SYSTEM LOCK". System Lock Password System Lock Password ENABLE 4 digits...
Page 140 2.8 Connection of 2.4 GHz Portable Stations Setting the Personal Identification Number (PIN) for PS Registration To prevent registering the PS to a wrong Hybrid IP-PBX, a PIN for PS registration can be set to the Hybrid IP-PBX. Before registering the PS to the Hybrid IP-PBX, register the PIN set to the Hybrid IP-PBX into the PS.
Page 141 2.8 Connection of 2.4 GHz Portable Stations PS Termination Confirm the following before canceling the PS registration: • PS is turned on. • PS is within the range. [691] PS No. 001 to 128 ENTER ENTER If "Rejected" or "Time out" is displayed CLEAR To the PS operation...
Page 142: Wall Mounting
2.8 Connection of 2.4 GHz Portable Stations 2.8.8 Wall Mounting Place the reference for wall mounting (on the following page) on the wall to mark the 2 screw positions. Install the 2 screws and washers (included) into the wall. Notes •...
Page 143 2.8 Connection of 2.4 GHz Portable Stations Reference for Wall Mounting Please copy this page and use as a reference for wall mounting. Install a screw here. 71 mm (2-13/16 in) Install a screw here. Note Make sure to set the print size to correspond with the size of this page. If the dimension of the paper output still deviates slightly from the measurement indicated here, use the measurement indicated here.
Page 144: Connection Of Doorphones, Door Openers, External Sensors, And External Relays
Connection of Doorphones, Door Openers, External Sensors, and External Relays The KX-TDA100 supports a maximum of 8 doorphones, 8 door openers, 8 external sensors, and 8 external relays. The KX-TDA200 supports a maximum of 16 doorphones, 16 door openers, 16 external sensors, and 16 external relays.
Page 145 2.9 Connection of Doorphones, Door Openers, External Sensors, and External Relays Pass the wires through the hole in the base cover, and attach the base cover to a wall using 2 screws. Screw To 8-pin terminal block Note Two kinds of screws are included with KX-T30865. Please choose the appropriate kind for your wall type.
Page 146 2.9 Connection of Doorphones, Door Openers, External Sensors, and External Relays Attach the terminal blocks to the connectors of the DPH4/EIO4 card on the Hybrid IP-PBX. To doorphones/ door openers/ external sensors/ external relays Installation Manual...
Page 147: 2.10 Connection Of Peripherals
2.10 Connection of Peripherals 2.10 Connection of Peripherals 2.10.1 Connection of Peripherals Maximum Distance Under 5 m (16 ft) Server PC Cable Maximum Distance 26 AWG to 22 AWG: Under 10 m (32 ft) CAT 5: Under 10 m (32 ft) BGM/ Music on Hold Cable...
Page 148 2.10 Connection of Peripherals Pager Up to 2 paging devices (user-supplied) can be connected to the Hybrid IP-PBX. CAUTION External Paging Jacks are SELV ports and should only be connected to approved SELV devices. PC/Printer (via RS-232C) The Hybrid IP-PBX is equipped with an RS-232C interface. This interface provides communication between the Hybrid IP-PBX and the user-supplied devices such as PC or line printers.
Page 149 2.10 Connection of Peripherals For connecting printer/PC with a 25-pin RS-232C connector Hybrid IP-PBX Printer/PC Circuit Type Signal Signal Circuit Type Pin No. Pin No. (EIA) Name Name (EIA) RD (RXD) SD (TXD) RD (RXD) ER (DTR) SD (TXD) ER (DTR) DR (DSR) RS (RTS) CS (CTS)
Page 150 2.10 Connection of Peripherals PC/Server PC (via USB version 1.1) The Hybrid IP-PBX is equipped with a USB interface. This interface provides communication between the Hybrid IP-PBX and a PC or a Server PC. The PC is used for system programming, diagnostics and external system database storage (save/load) functions.
Page 151: 2.11 Power Failure Connections
2.11 Power Failure Connections 2.11 Power Failure Connections 2.11.1 Power Failure Connections When the power supply to the Hybrid IP-PBX fails, power failure transfer (PFT) will switch from the current connection to the Power Failure Connection. Refer to "2.4.1 Power Failure Transfer" in the Feature Guide for further information.
Page 152 2.11 Power Failure Connections RJ11 Connector Pin Assignments for CO line Card PFT Ports 1 and 2 Signal Name Function Ring port 2 Ring port 1 Tip port 1 Tip port 2 PFT Ports 3 and 4 (for LCOT16 card only) Signal Name Function Ring port 4...
Page 153: 2.12 Starting The Hybrid Ip-Pbx
2.12 Starting the Hybrid IP-PBX 2.12 Starting the Hybrid IP-PBX 2.12.1 Starting the Hybrid IP-PBX CAUTION • SD Memory Card must be inserted in the SD Memory Card slot of the MPR card before startup. • Before touching the System Initialize Switch, discharge static electricity by touching ground or wearing a grounding strap.
Page 154 2.12 Starting the Hybrid IP-PBX Plug the AC power cord into the Hybrid IP-PBX and an AC outlet, and turn on the Hybrid IP-PBX. The RUN indicator will flash. Note For safety reasons, do not stretch, bend, or pinch the AC power cord. To AC Outlet While the RUN indicator is flashing, return the System Initialize Switch to the "NORMAL"...
Page 155: Confirming The Co Line Connection
2.12 Starting the Hybrid IP-PBX Confirming the CO Line Connection After initialization, program the Hybrid IP-PBX and establish CO line connection, and then use a PT to confirm it. To confirm, dial [ ] [3] [7] + CO line number (3 digits) or press an S-CO button. You will hear a dial tone if CO line is available and connected.
Page 156 2.12 Starting the Hybrid IP-PBX Installation Manual...
Page 157: Guide For The Kx-Tda Maintenance Console
Section 3 Guide for the KX-TDA Maintenance Console Explains the installation procedure, structure, and basic information of the KX-TDA Maintenance Console. Installation Manual...
Page 158: Overview
3.1 Overview Overview 3.1.1 Overview KX-TDA Maintenance Console is designed to serve as an overall system programming reference for the Hybrid IP-PBX. To program and administer the Hybrid IP-PBX by PC, you need to install the KX-TDA Maintenance Console onto the PC. This manual describes overview and installation of the KX-TDA Maintenance Console only.
Page 159: Connection
3.2 Connection Connection 3.2.1 Connection Serial Interface Connection USB Port To USB Port To COM Port RS-232C Port Note For pin assignments and maximum cabling distance, refer to "2.10.1 Connection of Peripherals". LAN Connection via CTI-LINK Card RJ45 Switching Hub To network port Note For pin assignments and maximum cabling distance, refer to "2.6.6 CTI-LINK Card".
Page 160 3.2 Connection External Modem Connection Modem To RS-232C port (25-pin) To CO line/Hybrid IP-PBX extension RS-232C Port port assigned as the CO line destination (9-pin) External Modem Hybrid IP-PBX Signal Name Pin No. Pin No. Signal Name SD (TXD) RD (RXD) RD (RXD) SD (TXD) DR (DSR)
Page 161: Installation Of The Kx-Tda Maintenance Console
3.3 Installation of the KX-TDA Maintenance Console Installation of the KX-TDA Maintenance Console 3.3.1 Installing and Starting the KX-TDA Maintenance Console System Requirements Operating System ® ® • Microsoft Windows 98 SE, Windows Me, Windows 2000, or Windows XP Hardware ®...
Page 162 3.3 Installation of the KX-TDA Maintenance Console Starting the KX-TDA Maintenance Console and Assigning the Basic Items (Quick Setup) When you start the KX-TDA Maintenance Console with the Installer Level Programmer Code and connect to the Hybrid IP-PBX for the first time after initialization (with the factory default setting), Quick Setup will launch automatically.
Page 163 3.3 Installation of the KX-TDA Maintenance Console 5. Type the system password for installer (default: 1234), then click [OK] to log-in. 6. Follow the instructions of the wizard and assign the basic items (Quick Setup). 7. The program menu appears. You may now begin programming the Hybrid IP-PBX.
Page 164 3.3 Installation of the KX-TDA Maintenance Console Notes • During long programming sessions, it is highly recommended that you periodically save the system data to the SD Memory Card. If the Hybrid IP-PBX suffers a sudden power failure or if the system is reset for some reason and all system data is lost, it can be restored from the SD Memory Card.
Page 165: Troubleshooting
Section 4 Troubleshooting This section provides information on the Hybrid IP-PBX and telephone troubleshooting. Installation Manual...
Page 166: Troubleshooting
4.1 Troubleshooting Troubleshooting 4.1.1 Installation PROBLEM PROBABLE CAUSE SOLUTION Extension does not operate. Bad extension card. • Exchange the card for a known working one. Bad connection between the • Take the telephone and plug it into the Hybrid IP-PBX and telephone. same extension port using a short telephone cord.
Page 167 4.1 Troubleshooting PROBLEM PROBABLE CAUSE SOLUTION The ALARM indicator on the A major system error occurs in • See the error log using the KX-TDA front of the cabinet turns on red. the Hybrid IP-PBX. Maintenance Console (refer to "4.1.5 Troubleshooting by Error Log").
Page 168: Connection
4.1 Troubleshooting 4.1.2 Connection Connection between the Hybrid IP-PBX and a PT: CAUSE SOLUTION Can you dial The T/R is connected to the D1/D2. Use the correct cord (the an extension? inner 2 wires are for T/R and the outer 2 wires are for D1/D2).
Page 169 4.1 Troubleshooting Connection between the central office and the Hybrid IP-PBX: CAUSE SOLUTION (Continued from the CO line is connected to the T2/T1. Reconnect the CO line to previous page.) the T1/R1 or T2/R2 of the telephone jack using 2-conductor wiring. Can you dial out on a CO line...
Page 170: Operation
4.1 Troubleshooting 4.1.3 Operation PROBLEM PROBABLE CAUSE SOLUTION • When using the • The HANDSET/HEADSET • When the headset is not used, set the speakerphone on an APT, selector is set to the HANDSET/HEADSET selector to the nothing is audible. "HEADSET"...
Page 171 4.1 Troubleshooting PROBLEM PROBABLE CAUSE SOLUTION • PS stays out of service • It may take about 20 s for • Wait until the CS starts up. when the CS status is CS to startup after the changed from Out of status has been changed to Service to In Service.
Page 172: Using The Reset Button
4.1 Troubleshooting 4.1.4 Using the Reset Button If the Hybrid IP-PBX does not operate properly, use the Reset Button. Before using the Reset Button, try the system feature again to confirm whether there definitely is a problem or not. CAUTION In order to avoid possible corruption of data on the SD Memory Card, please ensure that the "SD ACCESS"...
Page 173: Troubleshooting By Error Log
4.1 Troubleshooting 4.1.5 Troubleshooting by Error Log When a major system error occurs in the Hybrid IP-PBX, the ALARM indicator on the front of the cabinet turns on red, and the system logs the error information. Error Log Display Format Below is the display format of the error log.
Page 174 Five-digit sub code (1XXYY) 1: Cabinet number XX: Slot number KX-TDA100: 00 to 06 (00: MPR slot; 01 to 05: Free slot; 06: Option slot) KX-TDA200: 00 to 11 (00: MPR slot; 01 to 10: Free slot; 11: Option slot) YY: Physical port number (01 to 16) For OPB3 card, sub slot number + port number will be displayed.
Page 175 4.1 Troubleshooting List of Errors and Solutions The tables below list the errors and their solutions. When an error whose error code is indicated with "*" occurs in the Hybrid IP-PBX, the ALARM indicator on the front of the cabinet turns on red, and the system logs the error information. When the error conditions indicated by the error codes "021", "091", "092", "230", and "510"...
Page 176 4.1 Troubleshooting System Start-up and On-line Operation Error Code Error Message PROBABLE CAUSE SOLUTION 000* MPR WDT • MPR card malfunction • Press the Reset Button overflow • Optional service card • Reprogram the Hybrid IP-PBX malfunction: CTI-LINK • Replace the MPR card (be sure to turn SDRAM bit error •...
Page 177 4.1 Troubleshooting Error Code Error Message PROBABLE CAUSE SOLUTION CS overload • Defective cable • Check the cable diameter and length • CS malfunction • Replace the CS • Optional service card • Replace the corresponding optional malfunction: CSIF service card 020* SD file access •...
Page 178 4.1 Troubleshooting Error Code Error Message PROBABLE CAUSE SOLUTION 031* System data file • SD Memory Card not • Press the Reset Button not found installed • Reprogram the Hybrid IP-PBX • Bad connection of SD • Replace the SD Memory Card 032* System Memory Card...
Page 179 4.1 Troubleshooting Error Code Error Message PROBABLE CAUSE SOLUTION 202* LPR start up error • Optional service card • Pull out and re-insert the (No Program) malfunction: DHLC, DLC, corresponding optional service card CSIF, T1, PRI, OPB3, CTI- • Press the Reset Button 203* LPR start up error LINK, IP-GW, SLC8...
Page 180 4.1 Troubleshooting Error Code Error Message PROBABLE CAUSE SOLUTION 300* Digital trunk out of • Network (digital CO line) • Check the signals from the network synchronization malfunction • Check the cable • Optional service card • See if the A/B switch is set to A on the 301* Digital trunk RAI malfunction: PRI, T1...
Page 181 4.1 Troubleshooting Error Code Error Message PROBABLE CAUSE SOLUTION IP-GW SDRAM • Detection of IP-GW SDRAM • Replace the corresponding optional Failure error service card IP-GW DPRAM • Detection of IP-GW DPRAM • Replace the corresponding optional Failure error service card IP-GW LAN Chip •...
Page 182 4.1 Troubleshooting Error Code Error Message PROBABLE CAUSE SOLUTION IP-PT Rebooted • DHCP server is not active • Consult your network administrator (cause DHCP • Network malfunction server) • Network configuration has been changed IP-GW Rebooted • IP-GW is rebooted from a •...
Page 183 4.1 Troubleshooting Error Code Error Message PROBABLE CAUSE SOLUTION Data Link • Connection with PC Phone/ • This information is logged when established PC Console or Voice connection with PC Phone/PC Processing System (DPT Console or Voice Processing System Integration) established or (DPT Integration) is established, and restored does not indicate an error condition...
Page 184 4.1 Troubleshooting Installation Manual...
Page 185: Appendix
Section 5 Appendix Installation Manual...
Page 186: Revision History
5.1 Revision History Revision History 5.1.1 Version 1.1 New Options • System Components Table • KX-TDA0105 Memory Expansion Card (MEC) • KX-TDA0484 4-Channel VoIP Gateway Card (IP-GW4E) • KX-TDA0143 4 Cell Station Interface Card (CSIF4) • KX-T0141 2-Channel Cell Station Unit Using DHLC/DLC Card (PT-interface CS) for 2.4 GHz Portable Station New Contents •...
Page 187: Version 2.0
5.1 Revision History 5.1.2 Version 2.0 New Options • System Components Table • KX-TDA0490 16-Channel VoIP Gateway Card (IP-GW16) • KX-TDA0470 16-Channel VoIP Extension Card (IP-EXT16) • KX-TDA0164 4-Port External Input/Output Card (EIO4) • KX-TDA0168 Extension Caller ID Card (EXT-CID) •...
Page 188 5.1 Revision History Installation Manual...
Page 189: Index
Index Installation Manual...
Page 190 Guide for the KX-TDA Maintenance Console Before Site Survey Built-in Small Call Center Features Handling of the Cables Hospitality Features Calculation Example (KX-TDA100) Calculation Example (KX-TDA200) Cards Installed in the Slots of the Hybrid IP-PBX Installation Cards Mounted on Other Optional Service Cards...
Page 191 Index Operation Optional 3-Slot Base Card (KX-TDA0190) 24, 102 KX-TDA0103 (L-Type Power Supply Unit) 24, 42 Options KX-TDA0104 (M-Type Power Supply Unit) 24, 42 Overview 119, 158 KX-TDA0105 (Memory Expansion Card) 23, 70 KX-TDA0108 (S-Type Power Supply Unit) 24, 42 KX-TDA0143 (4 Cell Station Interface Card) 23, 85 Parallel Connection of the Extensions...
Page 192 Index Using the Reset Button Version 1.1 Version 2.0 Voice Mail Features Wall Mounting (CS) Wall Mounting (KX-TDA100) Wall Mounting (KX-TDA200) Wiring Precautions Installation Manual...
Page 193 Index Installation Manual...
Page 194 Copyright: This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced for internal use only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic Communications Co., Ltd. © 2003 Panasonic Communications Co., Ltd. All Rights Reserved.

This manual is also suitable for:

Kxtda200

Panasonic KX-TDA100 Installation Manual

1 System Outline

2 Installation

3 Guide for the KX-TDA Maintenance Console

4 Troubleshooting

5 Appendix

Index

Quick Links

Installation Manual

Troubleshooting

Related Manuals for Panasonic KX-TDA100

Summary of Contents for Panasonic KX-TDA100

This manual is also suitable for:

Table of Contents