Planet IPX-330 Installation Manual
Internet telephony pbx system
Hide thumbs
Also See for IPX-330:
- User manual (96 pages) ,
- User manual (143 pages) ,
- Quick installation manual (16 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Planet IPX-330
Summary of Contents for Planet IPX-330
- Page 1 Internet Telephony PBX System (30/100/500 SIP Users Registrations) IPX-330 / IPX-2100 / IPX-2500 Quick Installation Guide...
-
Page 2: Table Of Contents
Table of Contents 1. IPX-330 ..................... 3 1.1. Package Contents ................3 1.2. Hardware Installation ................3 1.2.1 Safety Instructions ..............3 1.2.2 Physical Introduction ..............4 1.2.3 LED & Button definitions ............. 4 1.2.4 Placement.................. 5 1.2.5 Physical Connection ..............5 1.3. Basic System Configuration ..............6 1.3.1 Web Login ................. -
Page 3: Ipx-330
The connections and equipment that supply power to the IPX-330 should be capable of operating safely with the maximum power requirements of the IPX-330. In the event of a power overload, the supply circuits and supply wiring should become hazardous. -
Page 4: Physical Introduction
1.2.2 Physical Introduction Internet Telephony PBX Ringing IPX-330 Front Panel of the IPX-330 12V DC Reset Rear Panel of the IPX-330 1.2.3 LED & Button definitions LED definitions Front Panel LED Status Description Steady Green PBX Power ON PBX Power OFF Blinking Green System is working... -
Page 5: Placement
Make sure the device is placed in a safe environment to avoid equipment failure. DO NOT place anything on top of the device. Excessive weight could damage it. DO NOT obstruct ventilation slots on each side of the IPX-330 or expose it to direct sunlight or other heat source. Be sure that there is adequate air flow around the IPX-330. -
Page 6: Basic System Configuration
1.3. Basic System Configuration 1.3.1 Web Login Step 1. Connect a computer to an ETH port on the IPX-330. Your PC must set up to the same domain as 192.168.0.X of the IPX-330. Step 2. Start a web browser. To use the user interface, you need a PC with Internet Explorer (version 6 and higher), Firefox, or Safari (for Mac). -
Page 7: Configuring The Network Setting
1.3.2 Configuring the Network Setting Step 1. Go to Network Settings Network Network & Country button Network Setting page... -
Page 8: Changing Ip Address Or Forgotten Admin Password
Step 2. Edit your ETH port IP information . There are three types of Ethernet port connection. They are Static IP, PPPoE (Point-to-Point Protocol over Ethernet) and DHCP. You can find detailed setting process in the user manual. Selection of IP Connection Type 1.3.3 Changing IP Address or forgotten admin password To reset the IP address to the default IP Address “192.168.0.1”... -
Page 9: Ipx-2100
If any of above items are damaged or missing, please contact your dealer immediately. 2.2. Hardware Installation The following are instructions for setting up PLANET IPX-2100. Refer to the illustration and follow the simple steps below to quickly install your Internet Telephony PBX system. -
Page 10: Physical Introduction
2.2.2 Physical Introduction Internet Telephony PBX System SLOT 1 SLOT 2 PWR SYS Ringing IPX-2100 Front Panel of the IPX-2100 12V DC SLOT 2 SLOT 1 Reset Console Rear Panel of the IPX-2100 Supporting 2 slots, user can buy expansion module like VIP-21FO (4 x FXO), VIP-21SL (2 x FXO + 2 x FXS) or VIP-21GS (4 x GSM) for extending port service. -
Page 11: Placement
Button Action Description Press less than 5 secs. System reboot Reset Press over 6 secs. Reset to Factory Default 2.2.4 Placement Make sure the device is placed in a safe environment to avoid equipment failure. DO NOT place anything on top of the device. Excessive weight could damage it. DO NOT obstruct ventilation slots on each side of the IPX-2100 or expose it to direct sunlight or other heat source. Be sure that there is adequate air flow around the IPX-2100. -
Page 12: Basic System Configuration
2.3. Basic System Configuration 2.3.1 Web Login Step 1. Connect a computer to an ETH port on the IPX-2100. Your PC must set up to the same domain as 192.168.0.X as the IPX-2100. Step 2. Start a web browser. To use the user interface, you need a PC with Internet Explorer (version 6 and higher), Firefox, or Safari (for Mac). -
Page 13: Configuring The Network Setting
2.3.2 Configuring the Network Setting Step 1. Go to Network Settings Network Network & Country button Network Setting page... -
Page 14: Changing Ip Address Or Forgotten Admin Password
Step 2. Edit your ETH port IP information. There are three types of Ethernet port connection. They are Static IP, PPPoE (Point-to-Point Protocol over Ethernet), DHCP. You can find detailed setting process in the user manual. Selection of IP Connection Type 2.3.3 Changing IP Address or forgotten admin password To reset the IP address to the default IP Address “192.168.0.1” (ETH) or reset the login password to default value. -
Page 15: Ipx-2500
If any of above items are damaged or missing, please contact your dealer immediately. 3.2. Hardware Installation The following are instructions for setting up PLANET IPX-2500. Refer to the illustration and follow the simple steps below to quickly install your Internet Telephony PBX system. -
Page 16: Physical Introduction
3.2.2 Physical Introduction Internet Telephony PBX System SLOT 2 SLOT 1 FXO/GSM Ringing IPX-2500 Front Panel of the IPX-2500 100~240V AC SLOT 2 SLOT 1 AUDIO Rear Panel of the IPX-2500 Supporting 2 slots, user can buy expansion module like VIP-21FO (4 x FXO), VIP-21SL (2 x FXO + 2 x FXS) or VIP-21GS (4 x GSM) for extending port service. -
Page 17: Placement
3.2.4 Placement Make sure the device is placed in a safe environment to avoid equipment failure. DO NOT place anything on top of the device. Excessive weight could damage it. DO NOT obstruct ventilation slots on each side of the IPX-2500 or expose it to direct sunlight or other heat sources. Be sure that there is adequate air flow around the IPX-2500. -
Page 18: Configuring The Network Setting
(Default IP) Default WAN IP: 172.16.0.1 Default LAN IP: 192.168.0.1 Default User Name: admin Default Password: admin Login page of the IPX-2500 For security reason, please change and memorize the new pass- word after this first setup. Note 3.3.2 Configuring the Network Setting Step 1. Go to Network Settings Network Network & Country button... - Page 19 Network setting page Step 2. Edit your WAN port IP information. There are three types of Ethernet port connection. They are Static IP, PPPoE (Point-to-Point Protocol over Ethernet), DHCP. You can find detailed setting process in the user manual. Selection of IP Connection Type...
-
Page 20: Further Configuration
If you need more support information, please contact PLANET support team. PLANET online FAQ : http://www.planet.com.tw/en/support/faq.php Support team mail address: support_voip@planet.com.tw Copyright © PLANET Technology Corp. 2014. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.