Invacare® XLT is a wheelchair with many adjustment options and accessories. To ensure that you benefit as much as possible from your Invacare® XLT, and in order to do its options justice, the chair must be tested and adjusted by competent personnel. We hope that you have also received instructions for using your Invacare®...
This provides a light weight and stable wheelchair. The black vinyl seat is easy to clean. The back rest is made of black plastic-coated fabric/black Strix. XLT Power U-front has a front that helps keep together the lower parts of XLT Power V-front the legs and the feet.
This symbol means warning. On this page a number of points affecting your personal safety are shown. Please Read it carefully! Invacare is only responsible for product changes carried out by per- ® sonnel who we authorise. We reserve the right to make any changes to equipment and specifications without prior notice.
Therefore the use of anti tip devices to achieve better stability is strongly recommended. • Invacare® XLT is designed to have a seat cushion on the seat. The seat cushion improves the user's body posture and makes it possible for him to sit comfortably for longer periods of time.
Frame colours Black, Grey, Blue and Red (Blasted titanium and Orange as special) Equipment and accessories Invacare® XLT has a wide range of accessories and options. Some of the accessories may not be available in all countries. Backrest Tension adjustable...
Seat width + 20 cm Seat width + 20 cm H (cm) 61-105 61-105 61-105 L (cm) 83-103 73-88 82-123 W (kg) 11,3 ML (kg) TW (kg)*** without seat cushion ** with 0° camber *** without rearwheels and accessories INVACARE ® XLT Service Manual...
Then retighten screw. NOTE! Do not adjust the upper screw (C). The distance between the lowest part of the footrest and the floor or ground must be at least 40 mm. Tools: 5 mm Allen Key INVACARE XLT Service Manual ®...
(A) at the footplate attachment with a 5 mm Allen key. Adjust the footplate to the correct position and retighten the screw. Do not place anything on the footplate when the screws have been loosened. Tools: 5 mm Allen Key INVACARE ® XLT Service Manual...
Page 12
5 mm Allen Key 2. The footrest can be flipped up. Lift the left side of the footrest upwards. Be careful not to trap your fingers between the footrest and the receiver when you fold down the footrest. INVACARE XLT Service Manual ®...
Lift up the front part, slide into required depth. 2. Adjusting the shape (tension adjustable seat) Use the straps underneath the seat to adjust the shape of the seat. Always have a cushion on the seat when testing its adjusted shape. INVACARE ® XLT Service Manual...
Hold the nut steady from the inside, and retighten the socket cap screw with the Allen key. Tools: 4 mm Allen Key 10 mm fixed spanner INVACARE XLT Service Manual ®...
Page 15
Hold the screws (A) firmly in place with the Allen key. The tip risk increases the further back the backrest is tilted. We recommend the use of anti-tip devices. Tools: 4 mm Allen key 10 mm fixed spanner INVACARE ® XLT Service Manual...
Loosen and remove screws (A) and the small plastic bracket (B) on the back of the back support. Adjust the backrest extension to the desired height and refit the screws. Tools: 4 mm Allen key INVACARE XLT Service Manual ®...
Take care not to loosen the two middle screws. Tools: 5 mm Allen key. These attach the supports to the frame. Take care that your fingers do not get caught between armrest/mudguard and tyre. INVACARE ® XLT Service Manual...
(on the side of, or between your legs) until it reaches the stopper. Release the brake by pushing the brake lever back (on the side of, or between your legs). Take care not to trap your fingers between brake shaft and tyre. INVACARE XLT Service Manual ®...
The cambered rearwheel plate is mounted and adjusted in the same way as the original rearwheel plate, see above. 1. Make sure that the rib (A) on the rearwheel plate and the chamfer (B) on the camber block is placed downwards. INVACARE ® XLT Service Manual...
(C) and tur- ning it to the desired angle. Retighten nuts (A). Check that the castor is securely fitted after replacement. Tools: 4 mm Allen key 5 mm Allen key 10 mm fixed spanner INVACARE XLT Service Manual ®...
For safety reasons we recommend the use of two anti-tip devices Make sure the anti-tip device is securely locked before use. Use extended anti-tip devices when an extended rear weel attachment is used. INVACARE ® XLT Service Manual...
Page 30
The distance between the anti-tip wheel and the ground, and the distance between the anti- tip wheel and rear wheel, should be approx. 5 cm. For safety reasons we recommend the use of two anti-tip devices INVACARE XLT Service Manual ®...
Remember to secure tightly when the desired position has been achieved. Be careful not to catch your thumb between the trunk support and the wheel when propell- ing the chair. Tool: 5 mm Allen key 13 mm fixed spanner INVACARE ® XLT Service Manual...
(A) using a 5 mm Allen key. 2. Attach the anti-tip device with adapter plate to the rear wheel attachment with the screws and washers (B) using a 4 mm Allen Key. Tools: 5 mm Allen Key 4 mm Allen Key INVACARE XLT Service Manual ®...
Pull the brake handle upwards and move the lock catch (A) upwards. Then release the handle. 3. Releasing the brake Pull the handle upwards and the lock catch will release automatically. Incorrect adjustments or use of the brakes can reduce their performance. INVACARE ® XLT Service Manual...
Tighten when the correct posi- tion is achieved. 2. When hole (A) is visible, just above the attachment, the handle will be in the right “locking-position”. Make sure the push handles care securely locked before use. INVACARE XLT Service Manual ®...
Make sure that the push handles have snapped into position, so that they cannot accidentally fold down again when the wheelchair is being pushed. PELVIC BELT The pelvic belt is strapped around the tubing under the seat (A). INVACARE ® XLT Service Manual...
Proprietary disinfectants may be used provided manufacturer's instructions are followed. The fabric may be washed at temperatures up to 71° C (160° F). using normal detergent. INVACARE XLT Service Manual ®...
When moving the brake pin it may be necessary to warm the brake pin/screw with a heat gun. At the factory the brake pin is tightened with thread soldering to prevent it from unthreading. INVACARE ® XLT Service Manual...
Anti-tip device, for one-arm drive - 4 mm Allen key, 5 mm Allen key Assistant manoeuvred drumbrakes - 5 mm Allen key, 22 mm fixed spanner Headrest, neckrest - 5 mm Allen key, 10 mm fixed spanner INVACARE XLT Service Manual ®...