Delta SS350 Instruction Manual
  1. Manuals
  2. Brands
  3. Delta Manuals
  4. Saw
  5. SS350
  6. Instruction manual

Delta SS350 Instruction Manual

16" variable speed scroll saw with quickset ii blade changing feature
Hide thumbs
Table of Contents

Advertisement

Quick Links

27051
16" Variable Speed Scroll Saw
with Quickset II
®
Blade
Changing Feature
(Models SS350, SS350LS)
PART NO. 912425 - 08-25-03
Copyright © 2003 Delta Machinery
To learn more about DELTA MACHINERY
ESPAÑOL: PÁGINA 19
RTD10000121AA
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
1-800-223-7278 (
1-800-463-3582).
please call
In Canada call

Advertisement

Table of Contents
loading

Related Manuals for Delta SS350

Summary of Contents for Delta SS350

  • Page 1 Blade Changing Feature (Models SS350, SS350LS) PART NO. 912425 - 08-25-03 Copyright © 2003 Delta Machinery To learn more about DELTA MACHINERY ESPAÑOL: PÁGINA 19 RTD10000121AA visit our website at: www.deltamachinery.com. For Parts, Service, Warranty or other Assistance, 1-800-223-7278 ( 1-800-463-3582).

  • Page 2: Safety Guidelines - Definitions

    If you have any questions relative to a particular application, DO NOT use the machine until you have first contacted Delta to determine if it can or should be performed on the product.
  • Page 3 BEFORE OPERATING of accessories and attachments not recom- MACHINE. Learning the machine’s application, mended by Delta may cause damage to the limitations, and specific hazards will greatly machine or injury to the user. minimize the possibility of accidents and injury.

  • Page 4: Additional Safety Rules For Scroll Saws

    19. THE USE of attachments and accessories not IL 60143-3201. Please refer to the American National recommended by Delta may result in the risk of injuries. Standards Institute ANSI 01.1 Safety Requirements for Woodworking Machines and the U.S. Department of 20.

  • Page 5: Power Connections

    POWER CONNECTIONS A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3- prong grounding type plugs and matching receptacle which will accept the machine’s plug.

  • Page 6: Extension Cords

    Delta ShopMaster Models SS350 and SS350LS 16" Scroll Saws are designed to give high quality, smooth cutting performance with capacity to cut up to 16" wide by 2" thick woodworking materials and have a 3/4" stroke. Delta ShopMaster Models SS350 and SS350LS come equipped with; integral dust port, variable speed 600-1650 spm, lock- out switch, cast iron table for minimal vibration, Quickset II ®...

  • Page 7: Carton Contents

    CARTON CONTENTS MODEL SS350LS ONLY MODEL SS350LS ONLY Fig. 1 1. Scroll Saw 6. Upper Back Brace 12" Long (1) 7. Stand Leg Foot (3) FOR MODEL SS350LS ONLY 8. 5/16-18x1½" Hex Head Screw (3) 9. 5/16" Flat Washer (6) 2.
  • Page 8 ASSEMBLY FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL. STAND (FOR MODEL SS350LS ONLY) NOTE: THE ASSEMBLY OF THIS STAND WILL USE M8X16MM CARRIAGE HEAD SCREWS AND M8 FLANGED HEX NUTS.

  • Page 9: Fastening Scroll Saw To Supporting Surface

    FASTENING SCROLL SAW TO SUPPORTING SURFACE This scroll saw MUST be securely fastened to a stand or workbench using the three holes, two of which are shown at (A) Fig. 4. The third hole is at the rear of the machine.

  • Page 10: Adjusting Blade Tension

    ADJUSTING BLADE TENSION Tension is applied to the blade when the blade tension lever (A) Fig. 7, has been adjusted and is in the vertical position as shown. When the blade tension lever (A) is moved to the horizontal position, as shown in Fig. 8, blade tension is released.

  • Page 11: Tilting The Table

    TILTING THE TABLE The table on your scroll saw can be tilted 45° to the left for bevel cutting operations by removing the dust cup as shown in Fig. 24 and loosening table lock knob (A) Fig. 10, tilt the table to the desired angle indicated on degree scale (B) Fig.

  • Page 12: Adjusting Holddown

    ADJUSTING HOLDDOWN The holddown (A) Fig. 15, should be adjusted so it contacts the top surface of the work (D) being cut. Loosen lock knob (B) and move holddown rod (C) up or down, then tighten lock knob (B). The holddown (A) Fig. 15, may be adjusted front to rear, by loosening set screw (B) Fig.

  • Page 13: Table Insert

    TABLE INSERT DISCONNECT MACHINE FROM POWER SOURCE. The table insert (A) can be positioned in the saw table with the opening in the insert pointing to the front of the table, as shown in Fig. 18, or to the right as shown in Fig. 19. With the table in the level position, 90°...

  • Page 14: Troubleshooting

    Make "relief" cuts before cutting long curves and never attempt to cut a curve that is too tight for the blade being used. INSIDE CUTTING Inside cutting takes place when the blade is threaded through a hole in the workpiece. With your Delta 16” Scroll Saw, you can perform this operation quickly and easily as follows: Loosen lock handle (A) Fig.

  • Page 15: Maintenance

    MAINTENANCE CHANGING BLADES DISCONNECT MACHINE FROM POWER SOURCE. 1. Remove table insert (A) Fig. 22, and release blade tension by pulling tension lever (B) forward, as shown. Fig. 22 2. Push upper blade chuck locking lever (C) Fig. 23, to the rear as shown.

  • Page 16: Fuse Replacement

    4. Push lower blade chuck locking lever (F) Fig. 25, to the rear as shown. This will release the blade (G) from the lower chuck (H). Fig. 25 5. Insert new blade (I) Fig. 26, into the upper blade holder (J) making certain the blade teeth are pointing down toward the table.
  • Page 17 (C) Fig. 21 where it pivots on the upper chuck. Fig. 29 ACCESSORIES A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers, www.deltamachinery.com and Delta Authorized Service Stations. Please visit our Web Site for a catalog or for the name of your nearest supplier.
  • Page 18 Two Year Limited New Product Warranty Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two years and provides Delta with reasonable opportunity to verify the alleged defect by inspection.
  • Page 19 Delta Distributor, Authorized · Service Center, or Porter-Cable Delta Factory Service Center. If you do not have access to any of these, call 800-223-7278 and you will · be directed to the nearest Porter-Cable Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades.

This manual is also suitable for:

Ss350ls

Table of Contents