Philips 46inch LCD TVchassis PL13.14 Service Manual

Philips 46inch LCD TVchassis PL13.14 Service Manual

46” lcd tv chassis pl13.14

Advertisement

Service Manual

TYPE A
46PFL3608/F7
46PFL3908/F7
46PFL3908/F8
46PFL3608/F7 A PHILIPS
TYPE B
46PFL3708/F7
46PFL3708/F8
This service manual contains information of different types of models.
Make sure to refer to the section describing your model.
This service manual contains information of different types of models.
Make sure to refer to the section describing your model.
© 2014 Funai Electric Co., Ltd.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.
with the
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.
PHILIPS
(Serial No.: DS1, DS2)
PHILIPS
(Serial No.: DS1, DS2)
PHILIPS
(Serial No.: XA1, XA2)
(Serial No.: DS3)
PHILIPS
(Serial No.: DS1)
PHILIPS
(Serial No.: XA1)
design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
chassis PL13.14
Contents
46" LCD TV
140224

Advertisement

Table of Contents
loading

Summary of Contents for Philips 46inch LCD TVchassis PL13.14

  • Page 1: Service Manual

    46PFL3608/F7 PHILIPS (Serial No.: DS1, DS2) 46PFL3908/F7 PHILIPS (Serial No.: DS1, DS2) 46PFL3908/F8 PHILIPS (Serial No.: XA1, XA2) 46PFL3608/F7 A PHILIPS (Serial No.: DS3) TYPE B 46PFL3708/F7 PHILIPS (Serial No.: DS1) 46PFL3708/F8 PHILIPS (Serial No.: XA1) This service manual contains information of different types of models.
  • Page 2: Important Safety Notice

    IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all P&F Equipment. The service procedures recommended by P&F and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.
  • Page 3: Table Of Contents

    TABLE OF CONTENTS Specifications [TYPE A] ..............1-1 [TYPE B] .
  • Page 4: Specifications [Type A]

    SPECIFICATIONS [TYPE A] < TUNER / NTSC > ANT. Input ---------------------- 75 Ω Unbal., F type Description Condition Unit Nominal Limit 1. AFT Pull-In Range ±2.3 ±2.1 TV.ch.4 dBµV 2. Synchronizing Sens. CA.ch.31 dBµV CA.ch.87 dBµV < TUNER / ATSC > Description Condition Unit...
  • Page 5: [Type B]

    [TYPE B] < TUNER / NTSC > ANT. Input ---------------------- 75 Ω Unbal., F type Description Condition Unit Nominal Limit 1. AFT Pull-In Range ±2.3 ±2.1 TV.ch.4 dBµV 2. Synchronizing Sens. CA.ch.31 dBµV CA.ch.87 dBµV < TUNER / ATSC > Description Condition Unit...
  • Page 6: Important Safety Precautions

    IMPORTANT SAFETY PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
  • Page 7 3. Design Alteration Warning - Do not alter or add 7. Product Safety Notice - Some electrical and to the mechanical or electrical design of this TV mechanical parts have special safety-related receiver. Design alterations and additions, characteristics which are often not evident from including, but not limited to circuit modifications visual inspection, nor can the protection they give and the addition of items such as auxiliary audio...
  • Page 8 Precautions during Servicing A. Parts identified by the # symbol are critical for safety. Replace only with part number specified. B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements.
  • Page 9 Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards. 1.
  • Page 10: Standard Notes For Servicing

    STANDARD NOTES FOR SERVICING Circuit Board Indications How to Remove / Install Flat Pack-IC 1. The output pin of the 3 pin Regulator ICs is 1. Removal indicated as shown. With Hot-Air Flat Pack-IC Desoldering Machine: Top View Bottom View 1.
  • Page 11 3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron: be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from pin or the solder lands under the IC when all pins of the flat pack-IC.
  • Page 12 With Iron Wire: 2. Installation 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more you can remove it easily.
  • Page 13: Instructions For Handling Semi- Conductors

    Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
  • Page 14: Cabinet Disassembly Instructions

    CABINET DISASSEMBLY INSTRUCTIONS Screw Torque Specification 2. Disassembly Method Ref. Part Tightening Step/ Part Name Fig. Number Torque Loc. Part Removal Note SCREW F-PAN 3CHROM GCJP3100 5.2±0.9lb·in +P-TITE M3X10.0 Stand SCREW F-PAN BLACK_NI L10 GCHP3120 6.1±0.9lb·in Hinge D1 4(S-1), 4(S-2) +P-TITE M3X12.0 Assembly SCREW BIND 3CHROM...
  • Page 15 (3) Fig. No. showing procedure of part location Precautions concerning the T-CON CBA Unit: (4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or 1. Be careful with the electrostatic discharge desoldered. when you repair/replace the T-CON CBA Unit. P = Spring, L = Locking Tab, S = Screw, •...
  • Page 16 (S-3) [1] Stand Hinge Assembly (S-3) (S-4) (S-4) [3] Rear Cover (S-1) (S-4) (S-2) [46PFL3908/F7, 46PFL3708/F7, 46PFL3708/F8, 46PFL3908/F8] [2] Stand Base Assembly [46PFL3608/F7, (S-2) 46PFL3608/F7 A] Fig. D1 PL13.14-A_DC...
  • Page 17 TYPE B Jack Holder [5] Digital Main CBA Unit TYPE A Jack Holder (S-6) (S-5) (S-6) (S-5) (S-6) (S-5) [4] Power Supply CBA (S-5) Fig. D2 PL13.14-A_DC...
  • Page 18 [11] LCD Panel Assembly [7] Bottom Cover L (S-8) (S-11) (S-7) (S-11) [10] Stand Bracket (S-10) Function Knob [6] Speaker [9] Function CBA Unit (S-9) [6] Speaker [8] Bottom Cover R Fig. D3 : Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the Function CBA Unit.
  • Page 19 [14] Front Cabinet (S-14) (S-14) Decoration Plate* Hook* (S-14) Sensor Plate* [13] IR Sensor CBA Unit T-CON Shield (S-12) (S-14) (S-12) FFC Cable [12] T-CON CBA Unit [All models except (S-13) 46PFL3608/F7 (Serial No.: DS2), T-CON Shield 46PFL3908/F7 (Serial No.: DS2), (S-12) 46PFL3908/F8 (Serial No.: XA2), [46PFL3608/F7 (Serial No.: DS2),...
  • Page 20 TV Cable Wiring Diagram To LCD Panel Assembly Power Supply CBA To T-CON CBA Unit Digital Main CBA Unit CN3906 CN3013 CN3601 CN1001 CN501 CN3602 CN3105 CN3801 CN3101 CN601 To AC Cord IR Sensor CBA Unit To Speaker CN4051 CN4052 *1: TYPE A Function CBA Unit *2: TYPE B...
  • Page 21: Electrical Adjustment Instructions [Type A]

    ELECTRICAL ADJUSTMENT INSTRUCTIONS [TYPE A] 1. Purity Check Mode This mode cycles through full-screen displays of red, General Note: “CBA” is abbreviation for green, blue, and white to check for non-active pixels. “Circuit Board Assembly.” 1. Enter the service mode. Note: Electrical adjustments are required after 2.
  • Page 22: White Balance Adjustment

    The White Balance Adjustment should be 6. Press [MENU] button. The internal Raster signal appears in the screen. (“Internal (Single)” appears performed when replacing the LCD Panel, in the upper right of the screen as shown below.) Digital Main CBA or T-CON CBA. 2.
  • Page 23 13. Press [9] button to select the “LDB” for Low Drive Blue adjustment (“LDB” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature. Internal (Single) 14. Press [7] button to select the “LDR” for Low Drive Red adjustment (“LDR”...
  • Page 24 The VCOM Adjustment should be 3. Enter the service mode. performed when replacing the T-CON 4. Press [2] button to select the VCOM1 adjustment. CBA. 5. Press [1] button. VCOM1 pattern signal (1 X 1 flicker) appears in the screen. 3.
  • Page 25: [Type B]

    [TYPE B] 1. Purity Check Mode This mode cycles through full-screen displays of red, General Note: “CBA” is abbreviation for green, blue, and white to check for non-active pixels. “Circuit Board Assembly.” 1. Enter the service mode. Note: Electrical adjustments are required after 2.
  • Page 26 The White Balance Adjustment should be 6. Press [MENU] button. The internal Raster signal appears in the screen. (“Internal (Single)” appears performed when replacing the LCD Panel, in the upper right of the screen as shown below.) Digital Main CBA or T-CON CBA. 2.
  • Page 27 The VCOM Adjustment should be 3. Enter the service mode. performed when replacing the T-CON 4. Press [2] button to select the VCOM1 adjustment. CBA. 5. Press [1] button. VCOM1 pattern signal (1 X 1 flicker) appears in the screen. 3.
  • Page 28: How To Initialize The Lcd Tv

    HOW TO INITIALIZE THE LCD TV The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized. To put the program back at the factory-default, initialize the LCD TV using the following procedure.
  • Page 29: Firmware Renewal Mode[Type A]

    FIRMWARE RENEWAL MODE [TYPE A] screen appears as follows. (Files included in the USB storage device are displayed.) " * " differs depending on the models. Equipment Required *****_******.upg Select an upgrade file 1. USB storage device *****_******.upg 2. Remote Control Unit *****_******.upg Firmware Update Procedure 1.
  • Page 30: [Type B]

    [TYPE B] Equipment Required a. USB storage device b. Remote Control Unit Firmware Update Procedure User Upgrade (Filename example: TVNB1012_00_PG_XX91_BA0.bin) Upgrade the firmware only. The setting values will not be initialized. The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to upgrade the firmware and initialize the setting values also, add “FACT_”...
  • Page 31 Factory Upgrade (Firmware Upgrade/Flash Upgrade) Firmware Upgrade (Filename example: FACT_TVNB1012_00_PG_XX91_BA0.bin) Upgrade the firmware and initialize the setting values. The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to upgrade the firmware and initialize the setting values also, add “FACT_” at the beginning of the filename. If you want to upgrade the firmware only and leave the setting values as they are, eliminate the “FACT_”...
  • Page 32: Troubleshooting

    TROUBLESHOOTING Note: This Troubleshooting section covers the entire PL13.14 chassis models. Thus some Reference number of parts shown below may not be used depending on the model. Please refer to the parts list for each model. [Power Supply Section] FLOW CHART NO.1 The power cannot be turned on.
  • Page 33 FLOW CHART NO.5 P-ON+21V is not output. Check C651, C652, D650 and their periphery circuit. Repair it if defective. FLOW CHART NO.6 AMP+13V is not output. Check C654, C655, D653, D654, D655 and their periphery circuit. Repair it if defective. FLOW CHART NO.7 [TYPE A] AL+3.3V is not output.
  • Page 34 [Video Signal Section] FLOW CHART NO.1 The key operation is not functioning. Replace the Function CBA Unit. Replace the Digital Main CBA Unit. FLOW CHART NO.2 No operation is possible from the remote control unit. (Operation is possible from the unit.) Check AL+3.3V line and repair it if defective.
  • Page 35 [Audio Signal Section] FLOW CHART NO.1 Audio is not output normally. See FLOW CHART NO.6 <AMP+13V is not output. [Power Supply Section]> See FLOW CHART NO.7 <AL+3.3V is not output. [Power Supply Section]> Replace the Digital Main CBA Unit. PL13.14ATR...
  • Page 36: Block Diagrams [Type A]

    BLOCK DIAGRAMS [TYPE A] 1. System Control Block Diagram PL13.14ABLS...
  • Page 37 2. Video/Audio Block Diagram PL13.14ABLVA...
  • Page 38 3. Digital Signal Process Block Diagram PL13.14ABLD...
  • Page 39 4. LED Backlight Drive Block Diagram PL13.14BLBD...
  • Page 40 5. Power Supply Block Diagram PL13.14ABLP...
  • Page 41: [Type B]

    [TYPE B] 1. System Control Block Diagram PL13.14BBLS...
  • Page 42 2. Video/Audio Block Diagram PL13.14BBLVA...
  • Page 43 3. Digital Signal Process Block Diagram PL13.14BBLD...
  • Page 44 4. LED Backlight Drive Block Diagram PL13.14BLBD...
  • Page 45 5. Power Supply Block Diagram PL13.14BBLP 9-10...
  • Page 46: Schematic Diagrams / Cba And Test Points

    SCHEMATIC DIAGRAMS / CBA AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
  • Page 47 LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V. 2.
  • Page 48 Power Supply 1 Schematic Diagram CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. NOTE: CAUTION ! : For continued protection against risk of fire, If Main Fuse (F602) is blown , check to see that all components in the power supply The voltage for parts in hot circuit is measured using replace only with same type 2.5A, 250V fuse.
  • Page 49 Power Supply 2 Schematic Diagram L1203 BEAD L1201 L1101 C1201 C1202 C1203 C1101 C1102 C1103 100uH 100uH 100/63V 1/100V 1/100V 100/63V 1/100V 1/100V D1202 D1102 SB2150BD SB2150BD BC1201 BC1202 BC1101 BC1102 D1205 L1202 L1102 C1207 C1208 C1209 C1205 BEAD WIRE D1203 C1107 C1108...
  • Page 50 Function Schematic Diagram FUNCTION CBA UNIT TO IR SENSOR CBA UNIT CN4051 CN4001 KEY-IN1 C4002 D4001 MM5Z5V6B D4002 OPEN R4006 R4005 R4004 R4003 R4002 R4001 2.2K 2.2K 2.7K 4.7K 8.2K SW4007 SW4006 SW4005 SW4004 SW4003 SW4002 SW4001 POWER SOURCE MENU CH UP DOWN DOWN...
  • Page 51: Ir Sensor Cba Unit

    IR Sensor Schematic Diagram C4054 R4060 R4053 RS4051 OPEN 2.7K RS-272 (REMOTE SENSOR) D4051 SMLE12WBC7W1HR POWER R4051 R4052 TO DIGITAL MAIN 6.8K CBA UNIT CN3101 R4054 CN4052 or CN3105 1 AL+3.3V 2 P-ON+5V 3 LIGHT C4051 C4056 C4052 1000P 4 LED1 5 REMOTE C4053 C4055...
  • Page 52 Digital Main 1 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. CONTINUE (NO CONNECTION) CN3905...
  • Page 53 Digital Main 2 Schematic Diagram [TYPE A] CONTINUE DIGITAL 7 P-ON+21V R3942 P-ON+3.3V OPEN CONTINUE R3952 D3905 DIGITAL 2 Q3905 OPEN OPEN OPEN LCD+12V/+21V C3996 OPEN D3906 OPEN IC3901 MP1472GJC452Z R3899 R3550 OPEN 6.8K (+12V REG.) C3946 0.047 R3897 C3949 OPEN R3891 TO LCD PANEL...
  • Page 54 Digital Main 3 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. IC3101(2/7) MN2WS0270HA DIGITAL MAIN CBA UNIT...
  • Page 55 Digital Main 4 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. IC3101(3/7) MN2WS0270HA DIGITAL SIGNAL PROCESS...
  • Page 56 Digital Main 5 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 7 TU3001...
  • Page 57 Digital Main 6 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT IC3101(5/7) MN2WS0270HA...
  • Page 58 Digital Main 7 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 1 P-ON+21V...
  • Page 59 Digital Main 8 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT R3144 CONTINUE...
  • Page 60 Digital Main 1 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into five and shown as IC3001 (1/5) ~ IC3001 (5/5) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT CONTINUE DIGITAL 5...
  • Page 61 Digital Main 2 Schematic Diagram [TYPE B] CONTINUE DIGITAL MAIN CBA UNIT DIGITAL 1 PANEL-VCOM-PWM CELL-PWR-CTRL R3039 LCD+12V OPEN R3035 OPEN CN3001 (NO CONNECTION) 31 LCD+12V C3514 C3513 30 LCD+12V OPEN OPEN 29 LCD+12V R3028 28 GND OPEN R3037 OPEN 27 VCOM-PWM C3918 C3921...
  • Page 62 Digital Main 3 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into five and shown as IC3001 (1/5) ~ IC3001 (5/5) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT IC3001(2/5) R3231...
  • Page 63 Digital Main 4 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into five and shown as IC3001 (1/5) ~ IC3001 (5/5) in this Digital Main Schematic Diagram Section. IC3001(3/5) MSD8200DS-S1 DIGITAL MAIN CBA UNIT...
  • Page 64 Digital Main 5 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into five and shown as IC3001 (1/5) ~ IC3001 (5/5) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT CONTINUE DIGITAL 3...
  • Page 65 Digital Main 6 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into five and shown as IC3001 (1/5) ~ IC3001 (5/5) in this Digital Main Schematic Diagram Section. TU3901 (TUNER UNIT) DIGITAL MAIN CBA UNIT IC3001(5/5)
  • Page 66 Power Supply CBA Top View Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, CAUTION ! when troubleshooting this type of power supply circuit, Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
  • Page 67 Power Supply CBA Bottom View Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, CAUTION ! when troubleshooting this type of power supply circuit, Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
  • Page 68: Wiring Diagrams [Type A]

    WIRING DIAGRAMS [TYPE A] 11-1 PL13.14AWI...
  • Page 69: [Type B]

    [TYPE B] 11-2 PL13.14BWI...
  • Page 70: Exploded Views

    EXPLODED VIEWS [TYPE A] LCD1 Digital Main CBA Unit CL3013 A4-1 [46PFL3608/F7 (Serial No.: DS1, DS2), T-CON 46PFL3908/F7 (Serial No.: DS1, DS2), CBA Unit 46PFL3608/F7 A (Serial No.: DS3)] SP3801 CL3701 CL4001 GP001 SSK1 IR Sensor CBA Unit [46PFL3608/F7 (Serial No.: DS2), 46PFL3908/F7 (Serial No.: DS2), CL3801 46PFL3908/F8 (Serial No.: XA2),...
  • Page 71 [TYPE B] LCD1 Digital Main CBA Unit CL3013 A4-1 [46PFL3708/F7 (Serial No.: DS1)] T-CON CBA Unit SP3801 CL3701 GP001 SSK1 CL4001 CL3801 IR Sensor CBA Unit CL3101 Function CBA Unit SP3802 GP003 SNA1 A4-2 Power Supply CBA AC601 See Electrical Parts List SBA1 for parts with this mark.
  • Page 72 Packing Upper Side Lower Side Tape [46PFL3608/F7, 46PFL3608/F7 A] [46PFL3708/F7, [46PFL3708/F7 (Serial No.: DS1)] SNA1 46PFL3908/F7, 46PFL3708/F8, 46PFL3908/F8] SSK1 Packing Tape SBA1 Packing Tape Packing Tape S I D E R E A R S I D E R E A R [46PFL3708/F8 (Serial No.: XA1), 46PFL3908/F8 (Serial No.: XA1, XA2)] Packing Tape...
  • Page 73: Parts List

    TYPE A PARTS LIST [46PFL3608/F7 (Serial No.: DS1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. OWNERS MANUAL A3RT0UH 2EMN00086 Before replacing any of these components, read REMOTE CONTROL UNIT YKF340-001 URMT39JHG003 carefully the product safety notice in this service...
  • Page 74: Electrical Parts

    Electrical Parts PRODUCT SAFETY NOTE: Products marked with a POWER SUPPLY CBA # have special characteristics important to safety. Ref. No. Description Part No. Before replacing any of these components, read POWER SUPPLY CBA A37Q0MPW-002 carefully the product safety notice in this service Consists fo the following manual.
  • Page 75 Ref. No. Description Part No. Ref. No. Description Part No. DIODES C1201 CAP ELE 100µF/63V/M/85 CEG1010V8006 C1202 CHIP CERAMIC CAP .(3216) X7R K 1.0µF/100V CA2A105MR080 D601# DIODE 1N5406BH NDL1001N5406 C1203 CHIP CERAMIC CAP .(3216) X7R K 1.0µF/100V CA2A105MR080 D602# DIODE 1N5406BH NDL1001N5406 C1205 CAP ELE 100µF/100V/M/85...
  • Page 76 Ref. No. Description Part No. Ref. No. Description Part No. RES CHIP 1608 1/10W J 22k Ω IC1601 IC DUAL-PHASE PFC CONTROLLER NSCA0T0TY087 R628 RRXA223HH013 UCC28063DR/R-PDSO-G RES CHIP 1608 1/10W J 47k Ω R629 RRXA473HH013 IC1602# IC PHOTOCOUPLER TLP781F(D4-FUNBLL F) QPEL781FBLLF RES CHIP 3216 1/4W J 560k Ω...
  • Page 77 Ref. No. Description Part No. Ref. No. Description Part No. RES CHIP 1608 1/10W J 1.0k Ω RES CHIP 3216 1/4W J 1.8k Ω R1122 RRXA102HH013 R1329 RRX4182HH034 RES CHIP 1608 1/10W J 10 Ω RES CHIP 1608 1/10W 0 Ω R1123 RRXA100HH013 R1330...
  • Page 78 Ref. No. Description Part No. BC1603 WIRE CP STP-S-0.50 XZ40F0REN001 BC1604 WIRE CP STP-S-0.50 XZ40F0REN001 BC1703 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 F602# FUSE TIME RAG SLT250V2.5A PDGSLB0NG252 GP001 EARTH PLATE A31FBUT 1EM440258 GP003 EARTH PLATE A31FBUT 1EM440258 JS601 WIRE CP STP-S-0.50 XZ40F0REN001 JS602 WIRE CP STP-S-0.50...
  • Page 79 TYPE A PARTS LIST [46PFL3608/F7 (Serial No.: DS2)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
  • Page 80 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1.
  • Page 81 TYPE A PARTS LIST [46PFL3608/F7 A(Serial No.: DS3)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
  • Page 82 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1.
  • Page 83 TYPE A PARTS LIST [46PFL3908/F7 (Serial No.: DS1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
  • Page 84 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1.
  • Page 85 TYPE A PARTS LIST [46PFL3908/F7 (Serial No.: DS2)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
  • Page 86 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1.
  • Page 87 TYPE A PARTS LIST [46PFL3908/F8 (Serial No.: XA1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
  • Page 88 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1.
  • Page 89 TYPE A PARTS LIST [46PFL3908/F8 (Serial No.: XA2)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
  • Page 90 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1.
  • Page 91 50W STAND BASE ASSEMBLY (PF) A21U2UD 1EMN29164 SNA1 50W STAND HINGE ASSEMBLY (PF) A21U2UD 1EMN29163 CARTON A3AQ2UH 1EM334640 OWNERS MANUAL A31T2UH 2EMN00084 REMOTE CONTROL UNIT YKF335-001 URMT39JHG001 QUICK START GUIDE A31T2UH 1EMN30381 REGISTRATION CARD (PHILIPS) A31T2UH 2EMN00134 2013/03/19 13-19 A3AQ2CA.fm...
  • Page 92 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1.
  • Page 93 TYPE B PARTS LIST [46PFL3708/F8 (Serial No.: XA1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
  • Page 94 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1.
  • Page 95: Revision History

    REVISION HISTORY Chassis PL13.14 • 2013/02/21 46PFL3608/F7 (Serial No.: DS1) added • 2013/03/29 46PFL3908/F7 (Serial No.: DS1) added • 2013/03/29 46PFL3708/F7 (Serial No.: DS1) added • 2013/05/31 46PFL3708/F8 (Serial No.: XA1) added • 2013/06/19 46PFL3908/F8 (Serial No.: XA1) added • 2013/12/28 46PFL3608/F7 (Serial No.: DS2) added •...
  • Page 96 COMPARISON LIST OF MODEL NAMES Chassis PL13.14 46PFL3608/F7 (DS1) A37QAUH TYPE A (DS2) A37QCUH TYPE A 46PFL3908/F7 (DS1) A37Q0UH TYPE A (DS2) A37QDUH TYPE A 46PFL3908/F8 (XA1) A37QBMA TYPE A (XA2) A37QEMA TYPE A 46PFL3708/F7 (DS1) A3AQ2UH TYPE B 46PFL3708/F8 (XA1) A3AQCMA TYPE B...

Table of Contents