Samsung UHD TV Quick Start Manual

QUICK START
GUIDE
BN68-05629A-00
3D Glasses Accessories:
3D Active glasses, USB charge cable
Step 1 Installing the Wall Mount
Installation Precautions
• Use the provided accessories and parts to install the wall mount.
• Install the product onto a flat wall surface only.
• Avoid the following areas to ensure the best product performance and prevent malfunctions:
- Areas that are susceptible to vibration and impact: The TV might come loose from the mount
and be damaged.
- Next to fire sprinklers: Heat generated by the TV could activate the sprinkler.
- Near high-voltage cables: Electronic interference from the high-voltage cables may disrupt
the screen display.
- Near a heating appliance: The product may overheat and malfunction.
- Check the stability of the wall surface.
- If the wall is too weak, reinforce it before installing the mount.
• Do not remove a section of the wall and install the mount there.
• Plug all the cables into the correct ports and connectors before installing the wall mount.
• If attempting to install the product onto a non-concrete wall, consult an installation specialist
first.
• Once installed, the gap between the wall surface and the TV should be at least 31 mm.
• For the types of walls the TV can be mounted on, check the model of your TV and then the
corresponding installation guide on the back of the product.
Wall Mount Accessories
Use only the provided accessories and parts to install the wall mount.
✎
A (4) B (8)
Mounting Piece M4 X 8
Wall Mount Brackets Length Adjustment D (24) E (24)
Left: 1, Right: 1 Bars M5 X 65 Anchor
Ø25 : 2
Welcome to your new Smart TV!
The following instructions cover assembling, connecting, and setting up your new TV. Make sure
you have the accessories listed below.
Included in this box
One Connect Accessories:
One connect, one connect cable
Smart Touch Control &
Batteries (AAA x 2)
Also included: User manual, regulatory guide, IR extender,
component adapter, RCA adapter x 2, power cord, Ferrite core
Using the
Installing the Connect Connect
Smart Touch
Wall Mount Audio Devices devices
Control
Step 1 Step 2 Step 3
] Check the type of the wall before installing.
Installation requirements for each wall type
• Can only be mounted on a concrete or interior wall of sufficient thickness. Refer to the diagrams
below.
Min. 50 mm
With MDF
or plywood Min. 30 mm
reinforcement
Min.
50 mm
MDF or PW
Art Wall
Min. 10 mm
Min. 10 mm
MDF or PW MDF or PW
NOTE
✎
MDF = Medium Density
Fiberboard
Min. 30 mm
PW = Plywood
Concrete
Art Wall
Min. 10 mm
MDF or PW
• Installation is not possible on a drywall or on a wall with no internal reinforcement.
MDF, PW, or Concrete
C (4)
M4 X 47
Art Wall
No internal
0~24 mm
reinforcement
F (2)
M6 X 30
1
1-1 1-1
wall
TV
1-1. If the wall is not flat, a gap may form
after the installation is completed and
this may result in a poor finish.
Check the wall's type, thickness, and flatness.
3
F
Power on and
start the initial
Drive the level adjustment screw into the hole to get it prepared for use.
setup
Step 4 Step 5
5
Min.
25 mm
MDF or PW
(Excluding
drywall thickness)
Place the assembly against the wall you wish to mount it on, and then mark the anchor insertion
points on the wall.
Min.
Requirements
25 mm
• Verify the location of the studs first and use wall screws.
Composite • Minimum Stud Size: 51x102mm or 2x4 in (Drill 3mm holes before inserting wall screws).
Concrete Wall
(Excluding • Drill the holes along the central axis of the stud.
drywall thickness)
• Inserting the screws without pre-drilling the holes can split the stud.
] The manufacturer will not be held liable for any issue arising from failure
to comply with the instructions and requirements contained in this
installation guide.
D
Drywall
Cannot install directly on drywall.
2
1-2 1-2
Object
wall
L
TV
Object
31mm
1-2. The TV cannot be mounted on the wall
if there is an object between the TV and
the wall that is 31 mm or thicker.
Check the L and R markings on the front sides of the wall mount brackets.
4
B
Attach the length adjustment bars to the two wall mount brackets using screws.
6
E
] Installation on drywall with studs.
7
Remove the screws that hold the wall mount brackets in place.
R
D
15mm
Insert the anchors and screws where marked.