Page 2
1/6" CCD Lens F 2.0 to 4.1, f = 2.3 mm to 69 mm, 30:1 power zoom lens (GR-DA30US) F 2.0 to 4.7, f = 2.3 mm to 78.2 mm, 34:1 power zoom lens (GR-DA30UC) Filter diameter Ø27 mm LCD monitor 2.4"...
PRECAUTIONS SAFTY PRECAUTIONS emission. Consequently, when servicing these products, Prior to shipment from the factory, JVC products are strictly inspected to conform with the recognized product safety and replace the cathode ray tubes and other parts with only the electrical codes of the countries in which they are to be specified parts.
Page 4
1.1.2 Safety Check after Servicing Examine the area surrounding the repaired location for damage (4) Leakage current test or deterioration. Observe that screws, parts and wires have been Confirm specified or lower leakage current between earth returned to original positions, Afterwards, perform the following ground/power cord plug prongs and externally exposed tests and confirm the specified values in order to verify accessible parts (RF terminals, antenna terminals, video...
SECTION 3 DISASSEMBLY BEFORE ASSEMBLY AND DISASSEMBLY 3.1.4 Tools required for disassembly and assembly 3.1.1 Precautions Torque driver Tweezers • Be sure to disconnect the power supply unit prior to mounting YTU94088 YTU94088-003 P-895 and soldering of parts. • Prior to removing a component part that needs to disconnect its connector(s) and its screw(s), first disconnect the wire(s) from the connector(s), and then remove the screw(s).
Page 7
3.2.2 ASSEMBLY/DISASSEMBLY OF CABINET PARTS AND ELECTRICAL PARTS Disassembly procedure NOTE14b: STEP Fig. PART NAME POINT NOTE During the procedure, be careful in handling the parts. NOTE17: BATT. COVER ASSY 3-2-1 4(L1) When attaching, tighten the screws in the reverse order of 3-2-2-1 GRIP BELT,3(S2a),S2b, REAR ASSY...
Page 14
3.2.3 ASSEMBLY/DISASSEMBLY OF [11] OP BLOCK ASSY Precautions Assembly of OP BLOCK ASSEMBLY / CCD BOARD AS- (1) Be careful in handling the CCD IMAGE SENSOR, OP SEMBLY LPF and the LENS components. Pay special attention (1) Set the OP LPF first, and then the SHEET to the OP not to soil or damage the surfaces., especially with re- BLOCK ASSY.
SECTION 4 ADJUSTMENT PREPARATION 4.1.3 TOOLS REQUIRED FOR ADJUSTMENT 4.1.1 Precaution Torque Driver Tweezers YTU94088 YTU94088-003 P-895 Camera system and deck system of this model are specially adjusted by using PC. However, if parts such as the following are replaced, an adjustment is required.
Page 16
• Chip IC replacement jig JIG CONNECTOR CABLE CONNECTION To be used for adjustment of the camera system. Connection procedure • Cleaning cloth Remove the COVER (JIG), and remove the COVER (AD- Recommended the Cleaning cloth to wipe down the video JUST).
Page 17
Jig connector JIG CONNECTOR CABLE (YTU93082J) JIG CONN. BOARD (PIN NO.) REAR CN102 -(NC) KENTO IF_RX AL_2.8VSYS AL_2.8VSYS IF_TX IF_RX ENV_OUT KENTO ATFI ATFI ENV_OUT IF_TX -(NC) Fig.4-2-3 MECHANISM COMPATIBILITY ADJUSTMENT 4.3.1 Tape pattern adjustment NOTE: Prior to the adjustment, remove the CASS.COVER. ENV_OUT (1) Play back the compatibility adjustment tape.
SECTION 5 TROUBLE SHOOTING SERVICE NOTE 1-18 (No.YF219)
Page 19
TAKING OUT CASSETTE TAPE If the tape cannot be taken out due to electrical failure, take out the tape in the following procedure. SCREW(1) SCREW(1) SCREW(1) Please note that following is a simplified method. Removing the cabinet parts before taking out the tape is rec- ommended for easy tape removal considering the workabili- ty and reliability.
Page 20
CASSETTE COVER PVC TAPE Fig.5-2-5 LOADING MOTOR LOADING MOTOR LOADING MOTOR Fig.5-2-6 SLIDE DECK ASSY Fig.5-2-7 CENTER GEAR CENTER GEAR SLIDE DECK SLIDE DECK ASSY Fig.5-2-8 1-20 (No.YF219)
Page 21
EMERGENCY DISPLAY Example (in case of the error number 01): When any abnormal signal is input to the syscon CPU, an error number is displayed on the LCD monitor. (Shown as examples UNIT IN REMOVE AND REATTACH 01 and 03) SAFEGUARD MODE BATTERY OR DC PLUG In every error status, the relevant messages as shown in the ex-...
Page 22
Victor company of Japan, Limited Camcorder Category 12, 3-chome, Moriya-cho, Kanagawa-ku, Yokohama-city, Kanagawa-prefecture, 221-8528, Japan (No.YF219) Printed in Japan...