Download Print this page
Invacare 1110266 Assembly And Installation Instructions Manual
Invacare 1110266 Assembly And Installation Instructions Manual

Invacare 1110266 Assembly And Installation Instructions Manual

Invacare bolt-in-place/spring button front rigging kit assembly and installation instruc

Advertisement

Quick Links

Bolt-In-Place/Spring Button Front Rigging Kit
Assembly and Installation Instructions
Kits No. 1110266 and 1121271
NOTE: Check ALL parts for shipping damage. In case of shipping damage, DO NOT use. Contact
Carrier/Dealer for further instruction.
To ensure the safe installation of the Bolt-In-Place/Spring Button Front Rigging
Kit, these instructions MUST be followed:
DO NOT install or use this equipment without first reading and understanding
these instructions and the Owner's Manual supplied with the wheelchair. If you
are unable to understand the Warnings, Cautions or Instructions, contact a
healthcare professional, dealer or technical personnel before attempting to
install this equipment - otherwise, injury or damage may occur.
After ANY adjustments, repair or service and before use, make sure all attaching
hardware is tightened securely - otherwise injury or damage may occur.
Bolt-In-Place Front Rigging Kit 1110266 contains the following items:
DESCRIPTION
Riv Nut
Button Head Screw
1/8-inch Hex key
Spring Buton Front Rigging kit 1112127 contains the following items:
DESCRIPTION
Spring buttons
INSTALLING THE BOLT-IN-PLACE FOOTPLATE KIT
(FIGURE 1)
NOTE: This kit mounts the footplate assembly to the front rigging support so that tools are required
to remove or adjust the footrest assembly.
1. Remove the front rigging from the wheelchair. Refer to the wheelchair owner's
manual shipped with wheelchair.
2. Pull up on the cam lock lever to unlock the cam.
NOTE: The elevating legrest has two (2) sets of release buttons, one (1) set above the other. Each
set will be visible one at a time allowing finer footplate height adjustment.
3. Push IN and hold the release button as shown in DETAIL "A" of FIGURE 1.
4. Rotate the lower footplate assembly 1/4 turn.
Part No. 1114831
SAVE THESE INSTRUCTIONS

SAFETY SUMMARY

WARNING
INSTALLATION WARNING
1
QUANTITY
2
2
1
QUANTITY
4
Bolt-In-Place/Spring Button
Front Rigging Kit

Advertisement

loading

Summary of Contents for Invacare 1110266

  • Page 1: Safety Summary

    INSTALLATION WARNING After ANY adjustments, repair or service and before use, make sure all attaching hardware is tightened securely - otherwise injury or damage may occur. Bolt-In-Place Front Rigging Kit 1110266 contains the following items: DESCRIPTION Riv Nut Button Head Screw...
  • Page 2 5. Remove the lower footplate assembly from the front rigging support. 6. Squeeze and push the release button down to remove from the footplate tube. 7. Ensure the cam lock lever is UP and unlocked. 8. Insert the footplate tube into the front rigging support. 9.
  • Page 3 BOLT-IN-PLACE HEIGHT ADJUSTMENT (FIGURE 1) NOTE: This procedure applies to the swingaway footrests and swingaway elevating legrest. 1. Remove the swingaway front rigging. Refer to INSTALLING/REMOVING THE FRONT RIGGINGS in the owner’s manual shipped with wheelchair. NOTE: Lay the front rigging assembly on a flat surface to simplify this procedure. 2.
  • Page 4 INSTALLING THE SPRING BUTTON FRONT RIGGING KIT (FIGURE 2) NOTE: This kit allows tool-less removal or adjustment of the footplate assembly. 1. Remove the front rigging from the wheelchair. Refer to the wheelchair owner’s manual shipped with wheelchair. 2. Pull the cam lock lever UP to UNLOCKED position. 3.
  • Page 5 DETAIL “A” Front Rigging Support Riv Nut Button Footplate Head Assembly Screw Lock Lever NOTE: Swingaway footrests shown. ELEVATING LEGRESTS/ ADJUSTABLE ANGLE FIGURE 2 - INSTALLING THE SPRING BUTTON FOOTPLATE KIT SPRING BUTTON HEIGHT ADJUSTMENT (FIGURE 2) NOTE: This procedure applies to the swingaway footrests and swingaway elevating legrest. 1.
  • Page 6 Bolt-In-Place/Spring Button Front Rigging Kit NOTES NOTES NOTES NOTES NOTES Part No. 1114831...
  • Page 7 Part No. 1114831 NOTES NOTES NOTES NOTES NOTES Bolt-In-Place/Spring Button Front Rigging Kit...
  • Page 8 Invacare Corporation One Invacare Way Elyria, Ohio USA 44036-2125 800-333-6900 MADE IN MEXICO Invacare is a registered trademark of Invacare Corporation. Yes, you can. is a trademark of Invacare Corporation. © 2003 Invacare Corporation Part No. 1114831 Rev B - 07/03...

This manual is also suitable for:

11148311121271