Remote Controller; Other - Integra DTR-7.4 Instruction Manual

Troubleshooting Guide—Continued
Symptoms
Selecting the "Music
Server" fails to play music
or fails to connect to the
server.
Search by album returns
no match.
Search by artist returns no
match.
Search by genre returns no
match.
No playlist can be selected.
The Net Audio information
is not displayed.
Front panel controls func-
tion but remote controller
controls do not.
LATE NIGHT function
cannot be used.
Re-EQ function cannot be
used.
Desired parameter cannot
be set.
Multichannel audio is not
output.
Components in remote
zone (Zone 2) do not oper-
ate properly.
Sound is sometimes heard
and sometimes not heard
with digital sources.
Causes
The Network Audio Server is not running. Turn on the Network Audio Server
No audio files found on the server.
The network is down because of some
failures.
The NTSP Port setting on the DTR-7.4
differs from that of the Network Audio
Server.
The audio file list of the Network Audio
Server contains no files that have album
names.
The audio file list of the Network Audio
Server contains no files that have artist
names.
The audio file list of the Network Audio
Server contains no files that have genre
names.
You have not yet created any playlists in
the Network Audio Server.
Depending on the model's shipping destina-
tion, the information on NET AUDIO and
Immediate Display may not be displayed
when the component video signal is output.
No batteries in remote controller.
Batteries are dead.
Remote controller is not pointed at the remote
sensor of the DTR-7.4.
Remote controller is too far from the
DTR-7.4.
Remote controller is functioning in a dif-
ferent mode.
The Transmission Signal Format setting
for the remote controller is wrong.
Playback source is not Dolby Digital
encoded.
Re-EQ may not be able to be set due to
current listening mode.
Parameter may not be able to be set due to
current listening mode.
The Multichannel setting is set to "No."
Input source is not connected to MULTI
CH INPUT port.
Components are incorrectly connected.
Objects are interfering with remote con-
troller signals.
One digital input format has been speci-
fied so other digital formats are not
played.
Remedies
Create MP3, MWA, and/or WAV audio files on the
Network Audio Server to create the list of audio
files saved on the server.
Turn off the power of the DTR-7.4 and turn it on
again (When the DTR-7.4 is without a power
switch, unplug the power cord and plug it in again).
If this does not resolve the problem, turn off the
power of the Network Audio Server and turn it on
again.
Go to "5-4. Client Setup Sub-menu," select "c.
NTSP Port," then set the same value as used for
the Network Audio Server (See page 78).
Assign album names to the files contained in the
audio file list of the Network Audio Server.
Assign artist names to the files contained in the
audio file list of the Network Audio Server.
Assign genre names to the files contained in the
audio file list of the Network Audio Server.
Create playlists in the Network Audio Server.
Set the Component Video setting to "VIDEO" at
Input Setup Menu → Video Setup Sub-Menu.
Insert batteries (See page 7).
Replace batteries (See page 7).
Point the remote controller at the remote sensor of
the DTR-7.4 (See page 7).
Operate the remote controller within 16 feet (5
meters) (See page 7).
To select Amp mode, press the scroll wheel (See
page 12). To select other mode, press the Mode
button, and then roll the scroll wheel to select your
favorite mode (See page 84).
If you change the remote controller's transmission
signal format to RF, be sure to select the same ID
as the RF receiver.
Check that the DOLBY DIGITAL indicator lights
up on the display (See page 55).
Select different listening mode (See page 55).
Check settings in Audio Adjust Menu (See pages
57 to 61).
Set the Multichannel setting to "Yes" at Setup
Menu → Input Setup Menu → Multichannel
Setup Sub-menu (See page 64).
Check connections (See page 64).
Check connections (See page 66).
Move inferring objects away from path of remote
controller signals.
Select "All" at Setup Menu → Input Setup Menu
→ Digital Setup Sub-menu → Digital Format
(See page 37).
101