Integra DTR-5.8 Instruction Manual page 96

Troubleshooting—Continued
• If the video source is connected to a component video
input, your TV must be connected to the COMPO-
NENT VIDEO OUT or HDMI OUT (page 25).
• If the video source is connected to an HDMI input,
your TV must be connected to the HDMI OUT
(page 25).
• On your TV, make sure that the video input to which
the AV receiver is connected is selected.
There's no picture from a source connected to
an HDMI IN
• If the message "Resolution Error" appears on the AV
receiver's display, this indicates that the TV or display
does not support the current video resolution and you
need to select another resolution on your DVD player.
The onscreen menus don't appear
• The onscreen menus may do not appear on a TV that's
connected to the HDMI OUT. When the HDMI Mon-
itor Out is set to No (page 47), the onscreen menus are
output at a resolution of 480i. If the onscreen menus
do not appear, set the HDMI Monitor Out to Yes
(page 47).
• Make sure that the video settings are correct (page 48).
• On your TV, make sure that the video input to which
the AV receiver is connected is selected.
The immediate display does not appear
• The immediate display appears on a device connected
to the COMPONENT VIDEO OUT, when the Com-
ponent Video Setup (page 49) is set to "---."
• If both of the HDMI Video Setup (page 48) and the
Component Video Setup (page 49) are set to "---," the
immediate display is output to a device connected to
the HDMI OUT.
Tuner
Reception is noisy, FM stereo reception is
noisy, or the FM STEREO indicator doesn't
appear
• Relocate your antenna.
• Move the AV receiver away from your TV or com-
puter.
• Listen to the station in mono (page 57).
• When listening to an AM station, operating the remote
controller may cause noise.
• Passing cars and airplanes can cause interference.
• Concrete walls weaken radio signals.
• If nothing improves the reception, install an outdoor
antenna.
96
Remote Controller
The remote controller doesn't work
• Make sure that the batteries are installed with the cor-
rect polarity (page 12).
• Install new batteries. Don't mix different types of bat-
teries, or old and new batteries (page 12).
• Make sure that the remote controller is not too far
away from the AV receiver, and that there's no
obstruction between the remote controller and the AV
receiver's remote control sensor (page 12).
• Make sure that the AV receiver is not subjected to
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary.
• If the AV receiver is installed in a rack or cabinet with
colored-glass doors, the remote controller may not
work reliably when the doors are closed.
• Make sure you've selected the correct remote control-
ler mode (pages 13-16).
• When using the remote controller to control other
manufacturers' AV components, some buttons may
not work as expected.
• Make sure you've entered the correct remote control
code.
• Make sure to set the same ID on both the AV receiver
and remote controller (pages 81 and 83).
Can't control other components
• If it's an Integra component, make sure that the
cable and analog audio cable are connected properly.
Connecting only an
• Make sure you've selected the correct remote control-
ler mode (pages 13-16).
• If you've connected an
recorder, CD recorder,
OUT jacks, or an Dock to the GAME/TV IN
jacks, for the remote controller to work properly, you
must set the display to MD, CDR, or DOCK (pages 51
and 91).
• To control another manufacturer's component, point
the remote controller at that component.
• To control an Integra component that's connected via
, point the remote controller at the AV receiver. Be
sure to enter the appropriate remote control code first
(page 91).
• To control an Integra component that's not connected
via , or another manufacturer's component, point
the remote controller at the component. Be sure to enter
the appropriate remote control code first (page 90).
cable won't work (page 39).
-capable Integra MD
Dock to the TAPE IN/