Download Print this page
GE JX827 Installation Instructions

GE JX827 Installation Instructions

Microwave oven built-in trim kits

Advertisement

Quick Links

Installation
Instructions
Questions? Call 1-800-561-3344 or Visit our Website at: geAppliances.ca

❒ BefOre YOu BegIn

read these instructions completely and carefully.
IMPOrTAnT
— Save these instructions
for local inspector's use.
IMPOrTAnT
— Observe all governing codes and
ordinances.
• note to Installer – Be sure to leave these instructions with
the Consumer.
• note to Consumer – Keep these instructions for future
reference.
• Skill level – Installation of this appliance requires basic
mechanical and electrical skills.
• Completion time – 1 to 3 hours
• P roper installation is the responsibility of the installer.
• P roduct failure due to improper installation is not covered
under the Warranty.
• T his kit is for use on models:
PEM10SFC, PEM10BFC, PEM10WFC and CEM11SFC
• D o not alter or modify any part of this kit or the oven.
• F or easier installation and personal safety, we
recommend that two people install this microwave oven.
• U nplug the microwave oven before attempting installation
of this kit.
WArnIng
— This oven must be plugged into a
properly grounded 3-hole, 120 volt receptacle as required by
the National Electrical Code.

fOr YOur SAfeTY:

WArnIng
— Before beginning the installation,
switch power off at service panel and lock the service
disconnecting means to prevent power from being switched
on accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.

Microwave Oven

Built-In Trim Kits
JX827 and JX830

PArTS InCluded

PArT
nOTe: This kit has extra screws to prevent the technician
from spending extra time locating a replacement in case
they lose one during installation.
1
QuAnTITY
❒ Base Pan
❒ Rail
❒ Trim Kit
❒ 4 mm x 10 mm
11 required
Screw A
3 extra
❒ 4 mm x 16 mm
4 required
Screw B
2 extra
1
2
1
1" 2.5 cm; 1' = 0.3 m

Advertisement

loading

Summary of Contents for GE JX827

  • Page 1: Microwave Oven

    Installation Microwave Oven Built-In Trim Kits Instructions JX827 and JX830 Questions? Call 1-800-561-3344 or Visit our Website at: geAppliances.ca PArTS InCluded ❒ BefOre YOu BegIn read these instructions completely and carefully. PArT QuAnTITY IMPOrTAnT • — Save these instructions ❒ Base Pan for local inspector’s use.
  • Page 2: Installation Instructions

    Installation Instructions TOOlS YOu WIll need ❒ 1 lOCATe And InSTAll The BASe PAn Set Base Pan into the front cabinet microwave oven cutout and center it right and left. Push back until the ❒ 2 Phillips Screwdrivers (#1 & #2) front flange is against the cabinet front wall. Mount the Base Pan using 3 screws (A). ❒ Drill with 3/32” Drill Bit ❒ Pencil ❒ Centerpunch or nail ❒ Knife ❒ Tape Measure Screw A ❒ Level ❒ CuTOuT dIMenSIOnS Trim Kit dimension Cutout 27”...
  • Page 3: Install The Microwave Oven

    Installation Instructions ❒ 2 InSTAll The rAIlS ❒ 4 CheCK leVelIng Disconnect the microwave oven from the receptacle. Check the leveling by placing a level at the front and sides Remove everything out of the microwave oven, including of the microwave. It may be necessary to add wood shims packing, Owner’s Manuals, turntable and turntable support. under the base pan to level the microwave front-to-back or A protective film has been applied to some microwave side-to-side. oven and trim kits. If applied, remove the film. Turn over the microwave oven and secure the rails to oven Base Plate by inserting 4 screws (A). Be careful not to scratch the microwave oven. Microwave Screw (A) Rail Oven Bottom ❒ 5 SeCure The rAIlS TO The CABIneT Ensure the Base Pan and Bottom Bracket front flanges are tight against the cabinet, and that the screws holes are aligned. Drive 4 screws (A) through the Base Pan and Rails...
  • Page 4 Installation Instructions ❒ 6 InSTAll The TrIM KIT frAMe ❒ 7 rePlACe AnY lOOSe ITeMS Your trim kit is now fully installed. Replace Position the assembled Trim Kit frame around the the turntable and turntable support that was removed oven. from inside the microwave oven. Secure the Trim Kit by driving four screws (B) through Keep these installation instructions and extra screws the trim kit into the cabinet. for future reference and need. Do not place them in the microwave oven.

This manual is also suitable for:

Jx830