Emerson LD195EM8 Service Manual

19? lcd tv/dvd

Hide thumbs Also See for LD195EM8:

Owner's manual (96 pages)

Table Of Contents

Table of Contents

Quick Links

Summary of Contents for Emerson LD195EM8

Page 1 EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A. SERVICE MANUAL 19″ LCD TV/DVD LD195EM8...
Page 2 IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.
Page 3: Table Of Contents
TABLE OF CONTENTS Specifications ................1-1 Laser Beam Safety Precautions .
Page 4: Specifications
SPECIFICATIONS < LCD TV Section > < TUNER / NTSC > ANT. Input ---------------------- 75 Ω Unbal., F type Description Condition Unit Nominal Limit 1. AFT Pull-In Range ±2.3 ±2.1 TV.ch.4 dBµ 2. Syncronizing Sens. CA.ch.31 dBµ CA.ch.87 dBµ < TUNER / ATSC > Description Condition Unit...
Page 5 <DVD Section> < DVD > Description Condition Unit Nominal Limit 1. Horizontal Resolution (TDV-540 TIT.2 CHP.16) Line 2. Video S/N (TDV-540 TIT.2 CHP.6) 3. Audio Distortion (LPCM 48 kHz, W/LPF) 0.03 0.07 (PTD 1-NOR TIT.1 CHP.1) L, 20 Hz 4. Audio freq. response (LPCM 48 kHz) R, 20 Hz +4/-5 (PTD 1-NOR TIT.1 CHP.5 -- 10)
Page 6: Laser Beam Safety Precautions
LASER BEAM SAFETY PRECAUTIONS This DVD player uses a pickup that emits a laser beam. Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin. The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30 cm away from the pickup lens when the diode is turned on.
Page 7: Important Safety Precautions
IMPORTANT SAFETY PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
Page 8 3. Design Alteration Warning - Do not alter or add 7. Product Safety Notice - Some electrical and to the mechanical or electrical design of this TV mechanical parts have special safety-related receiver. Design alterations and additions, characteristics which are often not evident from including, but not limited to circuit modifications visual inspection, nor can the protection they give and the addition of items such as auxiliary audio...
Page 9 Precautions during Servicing A. Parts identified by the # symbol are critical for safety. Replace only with part number specified. B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements.
Page 10 Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards. 1.
Page 11: Standard Notes For Servicing
STANDARD NOTES FOR SERVICING Circuit Board Indications Pb (Lead) Free Solder 1. The output pin of the 3 pin Regulator ICs is Pb free mark will be found on PCBs which use Pb indicated as shown. free solder. (Refer to figure.) For PCBs with Pb free mark, be sure to use Pb free solder.
Page 12 around the flat pack-IC to protect other parts from With Soldering Iron: damage. (Fig. S-1-2) 1. Using desoldering braid, remove the solder from 3. The flat pack-IC on the CBA is affixed with glue, so all pins of the flat pack-IC. When you use solder be careful not to break or damage the foil of each flux which is applied to all pins of the flat pack-IC, pin or the solder lands under the IC when...
Page 13: Shown In Fig
2. Installation With Iron Wire: 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more you can remove it easily.
Page 14 Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
Page 15: Cabinet Disassembly Instructions
CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart Removal Step/ This flowchart indicates the disassembly steps for the Remove/*Unhook/ Loc. Part Fig. Unlock/Release/ cabinet parts, and the CBA in order to gain access to Note Unplug/Unclamp/ item(s) to be serviced. When reassembling, follow the Desolder steps in reverse order.
Page 16 Note: 3. CAUTION 2: When reassembling, confirm the FFC cable (CN201) is connected completely. Then (1) Order of steps in procedure. When reassembling, remove the solder from the three short lands of follow the steps in reverse order. These numbers FPC cable.
Page 17 [3] Rear Cabinet (S-3) (S-3) (S-1) (S-3) [2] Stand Cover [1] Arm Assembly (S-2) (S-2) Fig. D1 A84N0DC...
Page 18 (S-6) (S-6) (S-5) [4] DVD Main CBA Unit (S-6) [6] DVD Holder (S-4) [5] DVD Mechanism Remove two screws A, then short the three short lands by soldering as shown in View for A. Chassis Cover Screws A Pin A Either of two places View for A FPC Cable...
Page 19 [7] Jack Holder(D) (S-7) (S-8) [8] Digital Main CBA Unit (S-9) (S-11) [10] Jack Holder (A) (S-10) (S-11) [11] DTV Module CBA Unit (S-11) [12] Main CBA (S-11) [9] Junction CBA Fig. D3 A84N0DC...
Page 20 [18] Front Cabinet [14] LCD Module Earth Plate Assembly [17] Speaker (S-13) (S-16) (S-13) (S-13) (S-15) (S-16) [16] IR Sensor [17] Speaker (S-12) (S-13) [13] Tilt Stand Holder (S-13) (S-14) [15] Function CBA Fig. D4 A84N0DC...
Page 21 TV Cable Wiring Diagram DVD Main CBA Unit To DVD Mechanism CN201 CN301 CN801 CN601 CN401 To LCD Module Assembly Digital Main Main CBA CBA Unit CN1901 CN1902 CN701 CN1501 To LCD CN1502 CN1503 CN1504 Module Assembly CN401 CN702 CN703 CN704 CN402 CN707...
Page 22: Electrical Adjustment Instructions
ELECTRICAL ADJUSTMENT INSTRUCTIONS General Note: “CBA” is abbreviation for How to set up the service mode: “Circuit Board Assembly.” Service mode: Note: Electrical adjustments are required after 1. Use the service remote control unit. replacing circuit components and certain mechanical parts. It is important to perform 2.
Page 23 Button Button Item (on the service Data Value Item (on the service Data Value remote control) remote control) CLR-R CLR-R [SETUP (YUV)] [SETUP (DTV)] YUV D2 DTV D4 → [2] → [4] CLR-B CLR-B [SETUP (PC)] → [VOL. n] → [1] CLR-R *COR [SETUP (YUV)]...
Page 24 2. Purity Check Mode Button Item (on the service Data Value This mode cycles through full-screen displays of red, remote control) green, blue, and white to check for non-active pixels. LAST POWER [VOL. n] 1. Enter the Service mode. S or M 2.
Page 25 3. Auto Calibration [Component] The following adjustment normally are not attempted in the field. Only when replacing the LCD Panel then adjust Purpose: To bring the color adjustment of each as a preparation. component into standard alignment. 6. White Balance Adjustment Symptom of Misadjustment: If this adjustment is [Video] incorrect, component signals do not reproduce the...
Page 26 5. [CUTOFF] 2. Input the White Raster(70%=70IRE, 30%=30IRE). Press [1] button to select “COR” for Red Cutoff adjustment. Press [3] button to select “COB” for INPUT SIGNAL Blue Cutoff adjustment. [DRIVE] Press [4] button to select “DR” for Red Drive adjustment.
Page 27: How To Initialize The Lcd Tv/Dvd
HOW TO INITIALIZE THE LCD TV/DVD To put the program back at the factory-default, initialize the LCD TV/DVD using the following procedure. < DVD Section > < LCD TV Section > 1. Press [1], [2], [3], [4], and [DISPLAY] buttons on the 1.
Page 28: Firmware Renewal Mode
FIRMWARE RENEWAL MODE 1. Turn the power on and press [EJECT] button on the 5. After programming is finished, the disc will be remote control unit to put the LCD TV/DVD into ejected automatically. Fig. e appears on the screen DVD mode.
Page 29: Troubleshooting
TROUBLESHOOTING FLOW CHART NO.1 The power cannot be turned on. Is the fuse (F601) normal? See FLOW CHART No.2 <The fuse blows out.> Check if there is any leak or short-circuiting on the primary circuit component, and service it if defective. (C615, D605, D606, D607, D608, Q601, Q603, T601) Is the INV+22V line voltage normal?
Page 30 FLOW CHART NO.6 VT+33V is not output. FLOW CHART NO.7 LCD+24.5V is not output. FLOW CHART NO.8 DVD-ON+1.8V is not output. Is approximately 3.7V voltage supplied to the Check C908, D911 and their periphery circuit, cathode of D911? and service it if defective. FLOW CHART NO.9 P-ON+1.5V is not output.
Page 31 FLOW CHART NO.11 P-ON+3.3V is not output. FLOW CHART NO.12 DTV-ON+3.3V is not output. FLOW CHART NO.13 DTV-ON+2.5V is not output. FLOW CHART NO.14 DV+5V is not output. A84N0TR...
Page 32 FLOW CHART NO.15 P-ON+5V is not output. (P-ON+9V is outputted normally.) Replace Q927. FLOW CHART NO.16 DTV-ON+5V is not output. Replace Q907. FLOW CHART NO.17 INV+22V is not output. FLOW CHART NO.18 LCD+13V is not output. A84N0TR...
Page 33 FLOW CHART NO.19 P-ON+9V is not output. Replace Q918. FLOW CHART NO.20 AL+3.3V is not output. FLOW CHART NO.21 LCD+3.3V is not output. FLOW CHART NO.22 LCD-6.8V is not output. Replace Q934. A84N0TR...
Page 34 FLOW CHART NO.23 The key operation is not functioning. Re-install the switches (SW1101~SW1111, SW1113) correctly or replace the poor switch. Check the switches (SW1101~SW1111, SW1113) and their periphery, and service it if defective. Replace Digital Main CBA Unit. FLOW CHART NO.24 No operation is possible from the remote control unit.
Page 35 FLOW CHART NO.26 Picture does not appear normally.(Tuner input(Analog)) FLOW CHART NO.27 Picture does not appear normally.(S-Video input) Pin(8) : S-VIDEO-C Pin(10): S-VIDEO-Y FLOW CHART NO.28 Picture does not appear normally.(Y/Pb/Pr input) Pin(2) : VIDEO-Y Pin(5) : VIDEO-Pb Pin(12): VIDEO-Pr Pin(15): VIDEO-Y Pin(4) : VIDEO-Pb Pin(14): VIDEO-Pr...
Page 36 FLOW CHART NO.29 Picture does not appear normally.(DVD PB) Pin(1) : DVD-Y Pin(3) : DVD-Pb Pin(13): DVD-Pr Pin(15): VIDEO-Y Pin(4) : VIDEO-Pb Pin(14): VIDEO-Pr FLOW CHART NO.30 Picture does not appear normally.(Tuner input(Digital)) Pin(20): DVD-Y Pin(18): DVD-Pb Pin(17): DVD-Pr A84N0TR...
Page 37 FLOW CHART NO.31 Audio is not outputted normally.(Audio input) Check the line between Pin(2, 15) of IC852 and input terminal(JK704, JK705), and service it if defective. Check IC852 and there periphery circuit, and service it if defective. CN802: AUDIO(L) CN801: AUDIO(R) Check SP801,SP802 and there periphery circuit, and service it if defective.
Page 38 FLOW CHART NO.33 Audio is not outputted normally.(Tuner input(Analog)) Check IC31, TU61 and there periphery circuit, and service it if defective. Check IC851 and there periphery circuit, and service it if defective. Check IC852 and there periphery circuit, and service it if defective. CN802: AUDIO(L) CN801: AUDIO(R) Check SP801,SP802 and there periphery circuit,...
Page 39 FLOW CHART NO.35 Audio is not outputted normally.(PC Audio input) Replace Digital Main CBA Unit. Check IC853 and there periphery circuit, and service it if defective. CN802: AUDIO(L) CN801: AUDIO(R) Check SP801,SP802 and there periphery circuit, and service it if defective. 9-11 A84N0TR...
Page 40: Block Diagrams
BLOCK DIAGRAMS < LCD TV Section > System Control Block Diagram 10-1 A84N1BLS...
Page 41 IF/Video Block Diagram 10-2 A84N1BLIF...
Page 42 Audio Block Diagram 10-3 A84N1BLA...
Page 43 DTV Module Block Diagram A84N1BLDTV 10-4...
Page 44 LCD Block Diagram A84N1BLLCD 10-5...
Page 45 Power Supply Block Diagram A84N1BLP 10-6...
Page 46 LCD Backlight Block Diagram 10-7 A74F0BLLB...
Page 47 BLOCK DIAGRAMS < DVD Section > System Control / Servo Block Diagram A84N1BLSD 10-8...
Page 48 Digital Signal Process Block Diagram A84N1BLD 10-9...
Page 49: Schematic Diagrams / Cba's And Test Points
SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
Page 50 LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V. 2.
Page 51 MAIN 1/6 Schematic Diagram < LCD TV Section > VOLTAGE CHART CN61 Pin No. Voltage CN704 Pin No. Voltage 11-3 A84N1SCM1...
Page 52 MAIN 2/6 Schematic Diagram < LCD TV Section > VOLTAGE CHART CN702 Pin No. Voltage 11-4 A84N1SCM2...
Page 53 MAIN 3/6 Schematic Diagram < LCD TV Section > VOLTAGE CHART CN703 Pin No. Voltage 11-5 A84N1SCM3...
Page 54 MAIN 4/6 Schematic Diagram < LCD TV Section > A84N1SCM4 11-6...
Page 55 MAIN 5/6 Schematic Diagram < LCD TV Section > CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. NOTE: CAUTION ! : For continued protection against risk of fire, If Main Fuse (F601) is blown , check to see that all components in the power supply The voltage for parts in hot circuit is measured using replace only with same type 4 A, 125V fuse.
Page 56 MAIN 6/6 Schematic Diagram < LCD TV Section > VOLTAGE CHART CN707 Pin No. Voltage CN708 Pin No. Voltage 11-8 A84N1SCM6...
Page 57 Function & Junction Schematic Diagram < LCD TV Section > 11-9 A84N1SCF...
Page 58 IR Sensor & Junction Schematic Diagram < LCD TV Section > 2 NOTE: Either D1164 or D1165 is used for IR SENSOR CBA. A84N1SCIR 11-10...
Page 59 Digital Main 1/6 Schematic Diagram < LCD TV Section > 11-11 A84N1SCD1...
Page 60 Digital Main 2/6 Schematic Diagram < LCD TV Section > 1 NOTE: The order of pins shown in this diagram is different from that of actual IC1201. IC1201 is divided into four and shown as IC1201 (1/4) ~ IC1201 (4/4) in this Digital Main Schematic Diagram Section. 11-12 A84N1SCD2...
Page 61 Digital Main 3/6 Schematic Diagram < LCD TV Section > 1 NOTE: The order of pins shown in this diagram is different from that of actual IC1201. IC1201 is divided into four and shown as IC1201 (1/4) ~ IC1201 (4/4) in this Digital Main Schematic Diagram Section. 11-13 A84N1SCD3...
Page 62 Digital Main 4/6 Schematic Diagram < LCD TV Section > 1 NOTE: The order of pins shown in this diagram is different from that of actual IC1201. IC1201 is divided into four and shown as IC1201 (1/4) ~ IC1201 (4/4) in this Digital Main Schematic Diagram Section. A84N1SCD4 11-14...
Page 63 Digital Main 5/6 Schematic Diagram < LCD TV Section > 1 NOTE: The order of pins shown in this diagram is different from that of actual IC1201. IC1201 is divided into four and shown as IC1201 (1/4) ~ IC1201 (4/4) in this Digital Main Schematic Diagram Section. A84N1SCD5 11-15...
Page 64 Digital Main 6/6 Schematic Diagram < LCD TV Section > A84N1SCD6 11-16...
Page 65 DTV Module 1/2 Schematic Diagram < LCD TV Section > 11-17 A84N1SCDT1...
Page 66 DTV Module 2/2 Schematic Diagram < LCD TV Section > A84N1SCDT2 11-18...
Page 67 DVD Main 1/3 Schematic Diagram < DVD Section > 1 NOTE: Either IC461 or IC462 is used for DVD MAIN CBA UNIT. A84N1SCDV1 11-19...
Page 68 DVD Main 2/3 Schematic Diagram < DVD Section > A84N1SCDV2 11-20...
Page 69 DVD Main 3/3 Schematic Diagram < DVD Section > A84N1SCDV3 11-21...
Page 70 MAIN CBA Top View CAUTION ! NOTE: Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. The voltage for parts in hot circuit is measured using CAUTION ! : For continued protection against risk of fire, If Main Fuse (F601) is blown , check to see that all components in the power supply hot GND as a common terminal.
Page 71 MAIN CBA Bottom View Because a hot chassis ground is present in the power CAUTION ! supply circuit, an isolation transformer must be used. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, Also, in order to have the ability to increase the input If Main Fuse (F601) is blown , check to see that all components in the power supply...
Page 72 Function CBA Top View Function CBA Bottom View BA84N0F01011-2 11-24...
Page 73 JUNCTION CBA IR Sensor CBA Top View JUNCTION CBA Bottom View Top View BA84N0F01011-4 IR Sensor CBA Bottom View BA84N0F01011-6 11-25...
Page 74: Waveforms
WAVEFORMS < LCD TV SECTION > WF1 ~ WF7 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.) Input: NTSC Color Bar Signal (with 1kHz Audio Signal) Pin 6 of CN703 Pin 15 of CN703 CVBS 0.2V 20µs VIDEO-Pb...
Page 75 WAVEFORMS < DVD SECTION > WF8 ~ WF13 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.) Input: NTSC Color Bar Signal (with 1kHz Audio Signal) DVD Video (Power on (Stop) MODE) Pin 9 of CN707 Pin 5 of CN707 WF11 DVD-AUDIO(L)
Page 76: Wiring Diagram
WIRING DIAGRAM < LCD TV SECTION > 13-1 A84N1WI...
Page 77 WIRING DIAGRAM < DVD SECTION > DVD-Pr DVD-ON+5V 20 CD/DVD 19 DVD-Pb D 18 A 17 DVD-Y C 16 B 15 NU 14 VREF 13 DVD-AUDIO(L) NU 12 DVD-AUDIO-MUTE GND 11 DVD-AUDIO(R) CD-LD 10 GND(LD) 9 DVD-SPDIF DVD-LD 8 PD-MONI 7 GND(DVD-PD) 6 GND(CD-PD) 5 TS(-) 4...
Page 78: System Control Timing Charts
SYSTEM CONTROL TIMING CHARTS Disc In ~ Play/Play ~ Disc Out Disc Disc Disc Disc Play Rotation Stop 3.3V Disc IN (TL221) 1.65V Sled Drive (TP303) 1.65V Disc Drive (TP301) 1.65V Focus Drive (TP304) Tracking Drive 1.65V (TP302) 14-1 A84N0TI...
Page 79: Lead Identifications
LEAD IDENTIFICATIONS KIA7805API/P KTA1267-GR-AT/P 2SA950-O(TE2 F T) 2SC2120-Y(TE2 F T) KTC3199-GR-AT/P 2SD400(F) 1: IN 2: GND 3: OUT 1 2 3 E C B E C B 2SK3563(Q) LD1117V TC4053BF(EL N F) TC4052BF(ELNF) AN5832SA-E1V 1: Vin 2: Vo 3: GND 1 2 3 G D S AN17812A...
Page 80: Exploded Views
EXPLODED VIEWS Cabinet L3-10 DVD Main CBA Unit CL1708 CL1707 SP802 CL1902 CL1901 CL802A Digital Main CBA Unit LCD1 SP801 CL801A IR Sensor CBA DTV Module Function CBA CBA Unit See Electrical Parts List Main CBA for parts with this mark. AC601 Junction CBA 16-1...
Page 81 Packing Stand Assembly Tape Tape Packing Tape Packing Tape Some Ref. Numbers are not in sequence. Packing Tape Packing Tape 16-2 A84N1PEX...
Page 82: Mechanical Parts List
MECHANICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. REMOTE CONTROL NF605UD 192/ NF605UD ECNLC6.5D1/NF605 Before replacing any of these components, read DRY BATTERY(SUNRISE) R6SSE/2S XB0M451MS002 carefully the product safety notice in this service SCREW BAG A81N0UH 1EM424596A manual.
Page 83: Electrical Parts List
ELECTRICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. CHIP CERAMIC CAP . F Z 0.47µF/10V CHD1AZ30F474 Before replacing any of these components, read CHIP CERAMIC CAP .(1608) F Z 0.1µF/25V CHD1EZ30F104 carefully the product safety notice in this service CHIP CERAMIC CAP .(1608) F Z 0.1µF/25V...
Page 84 Ref. No. Description Part No. Ref. No. Description Part No. C710 CHIP CERAMIC CAP . CH J 330pF/50V CHD1JJ3CH331 C885 ELECTROLYTIC CAP . 10µF/50V M CE1JMASDL100 C711 CHIP CERAMIC CAP .(1608) B K 0.1µF/50V CHD1JK30B104 C889 CHIP CERAMIC CAP .(1608) CH J 1000pF/50V CHD1JJ3CH102 C712 CHIP CERAMIC CAP .(1608) CH J 47pF/50V...
Page 85 Ref. No. Description Part No. Ref. No. Description Part No. D411 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D924 ZENER DIODE MTZJT-7736B QDTB00MTZJ36 D412 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D925 ZENER DIODE MTZJT-7724B QDTB00MTZJ24 D413 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D926 ZENER DIODE MTZJT-776.8B QDTB0MTZJ6R8 D414 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133...
Page 86 Ref. No. Description Part No. Ref. No. Description Part No. CHIP RES. 1/10W J 3.3k Ω Q414 CHIP TRANSISTOR KTC3875S-GR-RTK/P NQ14KTC3875S R404 RRXAJR5Z0332 CHIP RES. 1/10W J 10k Ω Q501 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P R405 RRXAJR5Z0103 CARBON RES. 1/4W J 100 Ω Q601# FET MOS 2SK3563(Q) QFWZ2SK3563Q...
Page 87 Ref. No. Description Part No. Ref. No. Description Part No. CHIP RES. 1/10W J 10k Ω CHIP RES. 1/10W J 100k Ω R708 RRXAJR5Z0103 R827 RRXAJR5Z0104 CHIP RES. 1/10W J 10k Ω CHIP RES. 1/10W J 100k Ω R709 RRXAJR5Z0103 R828 RRXAJR5Z0104 CARBON RES.
Page 88 Ref. No. Description Part No. Ref. No. Description Part No. CHIP RES. 1/10W F 10k Ω R909 RRXAFR5H1002 R974 PCB JUMPER D0.6-P5.0 JW5.0T METAL OXIDE FILM RES. 2W J 0.82 Ω CHIP RES. 1/10W J 1k Ω R910 RN02R82DP004 R975 RRXAJR5Z0102 CARBON RES.
Page 89 IR SENSOR CBA Ref. No. Description Part No. CL802A WIRE ASSEMBLY SPEAKER 2PIN 2PIN / WX1A84N0-006 Ref. No. Description Part No. 110MM IR SENSOR CBA ---------- F601# FUSE 4.00A/125V PAGG20CNG402 Consists of the following: FH601 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002 CAPACITOR FH602...
Page 90 Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law. LD195EM8 A84N1UH 2008-04-08...

Emerson LD195EM8 Service Manual

Quick Links

Related Manuals for Emerson LD195EM8

Summary of Contents for Emerson LD195EM8

Table of Contents