Page 1
Table of Contents Safety Notice Hardware Pack Assembly Instruction Parts List Warranty Ordering Parts Model PWR 8 Retain This Manual for Reference 07-31-03 OWNER'S MANUAL POWERHOUSE CLUB POWER 8 IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com...
WARRANTY...…. 24 ORDERING PARTS...… 24 BEFORE YOU BEGIN Thank you for selecting the Powerhouse Power 8 by IMPEX FITNESS PRODUCTS. For your safety and benefit, read this manual carefully before using the machine. provide you complete customer satisfaction. If you have any questions, or find there are missing or damaged parts, we guarantee you complete satisfaction through direct assistance from our factory.
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE INSTRUCTIONS. IMPEX INC.
SQUAT/LAT PULL MACHINE ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Right Support (#5) to the Right Stabilizer (#1). Attach the Cross Brace (#3) to the Right Support.
Page 7
STEP 2 (See Diagram 2) A.) Attach an Upright Beam (#4) to the Right Stabilizer (#1) and the Right Support (#5). Secure the Upright Beam to the Right Stabilizer with two M10 x 2 3/8” Carriage Bolts (#56), one 7” x 3 1/8”...
Page 8
STEP 3 (See Diagram 3) A.) Attach the Rear Stabilizer (#21) and the Chromed Foot Support (#25) to the Cross Brace (#3). Secure them with two M10 x 3 ½” Carriage Bolts (#54), Ø ¾” Washers (#67) and M10 Aircraft Nuts (#69). B.) Attach the Support Bracket (#14) to the Rear Stabilizer.
Page 9
STEP 4 (See Diagram 4) A.) Attach the Lat Bar Frame Bracket (#20) to the top of the Rear Vertical Frame (#7). Secure it with two M10 x 5/8” Allen Bolts (#64) and Ø ¾” Washers (#67). B.) Attach the Left & Right Lat Bar Frames (#10 & 9) to the Lat Bar Frame Bracket (#20). Secure them with two M10 x 5 ¼”...
Page 11
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 330” Upper Cable (#51) to the swivel pulley pre-installed in the front of the Right Lat Bar Frame (#9). Install a Ball Stopper (#46) onto the end of the Cable.
Page 13
STEP 6 (See Diagram 6 & Cable Loop) A.) Attach the Ball end of the 185” Lower Cable (#52) to a Pulley (#36). B.) Attach the Pulley to the open bracket on the Cross Brace (#3). Secure it with one M10 x 1 ¾”...
SQUAT/LAT PULL MACHINE KEY NO. DESCRIPTION Right Stabilizer Left Stabilizer Cross Brace Upright Beam Right Support Left Support Rear Vertical Frame Upper Frame Right Lat Bar Frame 10 Left Lat Bar Frame 11 Lat Bar 12 Chrome Panel 13 Sliding Weight Post 14 Support Bracket 15 Olympic Weight Post 16 Right Safety Catch...
MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Main Frame (#1) to the Front & Rear Stabilizers (#2 & 3). Secure each end with two M10 x ¾”...
Page 19
STEP 2 (See Diagram 2) A.) Attach four Bushings (#26) to a Seat Support Frame (#6). B.) Attach a Backrest Support (#7) to the rear of the Seat Support Frame (#6). Align the holes and secure them with one M10 x 1 ¾” Allen Bolt (#36) and procedure to install the other side.
Page 20
STEP 3 (See Diagram 3) A.) Place the Backrest Board (#14) onto the Backrest Supports (#7). Secure it with four M8 x 2” Allen Bolts (#39) and B.) Place the Seat Pad (#13) onto the Seat Support Frames (#6). Secure it with four M8 x 2”...
Page 21
STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#5) to the open bracket on the Main Frame (#1). Secure it with an Axle (#17), two M10 x ¾” Allen Bolts (#35), and two B.) Insert one Foam Tube (#10) halfway through the hole on the Main Frame. Insert two Foam Tubes halfway through the holes on the Leg Developer (#5).
Page 22
STEP 5 (See Diagram 5) A.) Attach the Arm Curl Pad (#15) to the Arm Curl Stand (#4). Secure it with two M8 x 5/8” Allen Bolts (#40) and two opening on the Main Frame (#1). Use the Lock Knob to hold the desired Arm Curl height. B.) Attach the Curl Bar Support Frame (#11) to the open bracket on the Leg Developer (#5).
MULTI-PURPOSE BENCH PARTS LIST KEY NO. DESCRIPTION Main Frame Front Stabilizer Rear Stabilizer Arm Curl Stand Leg Developer Seat Support Frame Backrest Support Sliding Block Incline Adjustment Bar Foam Tube Curl Bar Support Frame Curl Bar Handle Seat Pad Backrest Board Arm Curl Pad Curl Bar Handle Grip Axle...
IMPEX. IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or whatsoever natures.