1. Manuals
  2. Brands
  3. Impex Manuals
  4. Home Gym
  5. MARCY MWM-7150
  6. Owner's manual

Impex MARCY MWM-7150 Owner's Manual

Impex fitness mercy home gym product manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWM-7150
Retain This
Manual for
Reference
08-20-08
OWNER'S
MANUAL
MARCY HOME GYM
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
MWM-7150
®
IMPEX
INC.

Advertisement

Table of Contents
loading

Related Manuals for Impex MARCY MWM-7150

Summary of Contents for Impex MARCY MWM-7150

  • Page 1 Parts List Resistance Chart Warranty Ordering Parts Model MWM-7150 Retain This Manual for Reference 08-20-08 OWNER'S MANUAL MARCY HOME GYM MWM-7150 IMPEX 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.com ® INC.

  • Page 2: Table Of Contents

    ORDERING PARTS...…………20 BEFORE YOU BEGIN ® Thank you for selecting the MARCY MWM-7150 HOME GYM by IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction.

  • Page 3: Important Safety Notices

    BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES RESPONSIBILITY SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

  • Page 4: Warning Label Replacement

    WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Base Frame and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.

  • Page 5: Hardware Pack

    HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
  • Page 6 HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.
  • Page 7 HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.

  • Page 8: Assembly Instructions

    ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten the nuts and bolts until instructed to do so. B.) Slide two Ø...
  • Page 9 DIAGRAM 1...
  • Page 10 A.) Attach the Vertical Frame (#2) onto the Main Frame (#1). Secure them with two M10 x 2 ¾” Carriage Bolts (#46), one 5 ½” x 2” Bracket (#12), two Ø ¾” Washers (#59), and two M10 Aircraft Nuts (#56). B.) Slide 14 Weight Plates (#40) onto the Guide Rods (#10).
  • Page 11 DIAGRAM 2...
  • Page 12 A.) Attach the Front Press (#4) to the Upper Frame (#3). Secure it with one Front Press Axle (#27), two Ø ¾” Washers (#59), and two M10 Aircraft Nuts (#56). Do not over tighten the Nuts. Make sure the Front Press can move smoothly. B.) Insert the two Front Press Handles (#15) into the arms of Front Press.
  • Page 13 STEP-4 (See Diagram 4) A.) Attach the Seat Pad (#31) to the Seat Support (#17). Secure it with two M8 x 1 5/8” Allen Bolts (#52) and Ø 5/8” Washers (#58). B.) Insert two Foam Tubes (#13) halfway through the holes on Front Post (#6) and Leg Developer (#7).
  • Page 14 CABLE LOOP DIAGRAM...
  • Page 15 A.) Attach the 182” Upper Cable (#41) to the front opening on the Upper Frame (#3). NOTE: The Ball Stopper on the Cable needs to be underneath the Frame. B.) Attach a Pulley (#26) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#53), two Ø...
  • Page 16 DIAGRAM 5...
  • Page 17 A.) Attach the 110” Lower Cable (#42) to the opening on the bottom of the Leg Developer (#7). B.) Attach a Pulley (#26) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#53), two Ø 7/8” Bushings (#23), and one M10 Aircraft Nut (#56). C.) Draw the Cable underneath the Pulley towards the back of the machine through the opening on the Front Post (#6) to the open bracket on rear of Front Post.
  • Page 18 DIAGRAM 6 110＂...

  • Page 19: Parts List

    PARTS LIST KEY NO. DESCRIPTION Main Frame Vertical Frame Upper Frame Front Press Rear Base Frame Front Post Leg Developer Lat Bar Selector Rod Guide Rod Double Floating Pulley Bracket 5 ½” x 2” Bracket Foam Tube Foot Plate Front Press Handle U-shaped Bracket Seat Support 4 ¾”...

  • Page 20: Weight Resistance Chart

    WEIGHT RESISTANCE CHART Station Lat Pull Low Pulley Front Press Leg Developer Station Lat Pull Low Pulley Front Press Leg Developer 134 Note: Each plate weights 10 lbs. Numbers are approximate. Actual weights may vary. WEIGHT PLATE WEIGHT PLATE...

  • Page 21: Warranty

    IMPEX. IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or whatsoever natures.

Table of Contents