Impex marcy premier home gym owner's manual premier (19 pages)
Summary of Contents for Impex Marcy Classic MCB 880-MG
Page 1
Warranty Ordering Parts Model MCB-880MG Retain This Manual for Reference 07-16-08 OWNER'S MANUAL MARCY MID-SIZE BENCH MCB 880-MG IMPEX 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.com ® CLASSIC ® INC.
PARTS LIST…………………………………………………………….……….……. WARRANTY...… ORDERING PARTS... BEFORE YOU BEGIN Thank you for selecting the MARCY CLASSIC MCB 880-MG MID-SIZE ® BENCH by IMPEX carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction. If you have any questions, or find there are missing or damaged parts, we guarantee you complete satisfaction through direct assistance from our factory.
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE INSTRUCTIONS. IMPEX INC.
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Stabilizer, Base Frame, and Lat Bar Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in location shown.
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the two Base Frames (#65) together on a flat surface. Attach the Left & Right Upright Beams (#67 &...
Page 8
STEP 2 (See Diagram 2) A.) Attach the Lat Bar Frame Support (#66) onto the joint of the two Base Frames (#65). Align the holes and secure them together with two M10 x 3 ¾” Carriage Bolts (#46), Ø ¾” Washers (#39) and M10 Aircraft Nuts (#51).
Page 9
STEP 3 (See Diagram 3) A.) Attach the 57” Cable (#74) to a Pulley (#57). Attach the Pulley to the top opening on the Lat Bar Frame (#70). Secure it with a M10 x 2 3/8” Allen Bolt (#48), two Pulley Bushings (#59), and one M10 Aircraft Nut (#51).
Page 10
STEP 4 (See Diagram 4) A.) Attach the Main Frame (#1) onto the Front & Rear Stabilizers (#2 & #6). Secure each end with two M10 x ¾” Allen Bolts (#32) and Ø ¾” Washers (#39). DIAGRAM 4...
Page 11
STEP 5 (See Diagram 5) A.) Attach the two Backrest Supports (#3) to the pivot on the Main Frame (#1). Secure it with one M12 x 5 ¾” Allen Bolt (#31), two Ø1” Washers (#38), and one M12 Aircraft Nut (#36). Do not over tighten the nut and bolt.
Page 12
STEP 6 (See Diagram 6) A.) Attach the Leg Developer (#5) to the open bracket on the Main Frame (#1). Secure it with one Axle (#42), two M10 x 5/8” Allen Bolts (#30), and two Ø ¾” Washers (#39). Do not over tighten the bolts. Make sure the Leg Developer is able to swivel. B.) Insert the U-shaped Pin (#10) into the tube in front of the Main Frame.
Page 13
STEP 7 (See Diagram 7) A.) Attach the Arm Curl Pad (#13) to the Arm Curl Stand (#7). Secure it with two M8 x ¾” Allen Bolts (#33) and Ø 5/8” Washers (#40). B.) Insert the Arm Curl Stand into the front opening on the Main Frame. Use a Lock Knob (#16) to secure the Stand at desired height.
Seat Pad Backrest Board Arm Curl Pad Olympic Sleeve Spring Clip Lock Knob (Impex Logo) 2 3/8” x 1 5/8” End Cap 1” Square End Cap Ø 1” End Cap M10 x 2 ¾” Allen Bolt Foam Roll End Cap Ø...
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the customer. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes.