SYMBOL EXPLANATION Symbols WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Read through the Operator‘s Manual carefully and understand the content before using the machine. Always use •...
Assembling the spray guard and trimmer head Auto32 (GR2126L) ... 13 Assembling other guards and cutting equipment (GR2126L) ... 13 Fitting the spray guard and trimmer head (GT2125L) ... 13 FUEL HANDLING Fuel mixture ... 14 Fuelling... 14 START AND STOP Control before starting ...
SAFETY INSTRUCTIONS Personal protective equipment MPORTANT INFORMATION • A clearing saw, brushcutter or trimmer used incorrectly or carelessly can become a dangerous tool, that can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the content of this manual.
SAFETY INSTRUCTIONS 4. Vibration damping system Your machine is equipped with a vibration damping system, which is designed to give as vibration-free and comfortable use as possible. Use of incorrectly wound cord or incorrect cutting equipment increases the level of vibration. The machine’s vibration damping system reduces the transfer of vibrations...
Control, maintenance and service of the machine‘s safety equipment IMPORTANT INFORMATION • All service and repairs to the machine require special training. • This applies especially to the machine‘s safety equipment. If the machine does not meet any of the controls listed below you should contact your service workshop.
SAFETY INSTRUCTIONS 6. Cutting equipment The section describes how through correct maintenance and through using the right type of cutting equipment you can: • Obtain maximum clearing capacity. • Increase the service life of the cutting equipment. Two basic rules: 1)Only use the cutting and guard equipment we recommend! See...
General safety instructions IMPORTANT INFORMATION • The machine is only designed for trimming grass. • The only accessories to be used with the engine unit as a drive source are the cutting units we recommend in the chapter “Technical data“ . •...
SAFETY INSTRUCTIONS General working instructions IMPORTANT INFORMATION • This section takes up the basic safety precautions for working with the trimmer. • If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop.
Page 10
Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. NOTE! This technique increases the wear on the cord.
What is what on the trimmer? 1. Trimmer head 2. Grease filler cap 3. Angle gear 4. Spray guard 5. Shaft 6. Loop handlebar 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. Cylinder cover 11. Starter handle 12. Fuel tank WHAT IS WHAT? 13.
Assembling the loop handlebar (GT2125L) • Position the handle on the shaft. Note that the handle must be mounted below the arrow on the shaft. • Fit the bolt, securing plate and wing nut as shown in the diagram. • Tighten the wing nut.
• Screw on the trimmer head (H) in the direction of rotation. • Dismantling takes place in the reverse order. Fitting the spray guard and trimmer head (GT2125L) Guard • Fit the guard as shown in the diagram. Tighten securely. Trimmer head •...
Two-stroke oil • For the best results use JONSERED two-stroke oil, which has been specially produced for clearing saws and chain saws. Mixing ratio 1:50 (2%). • Never use two-stroke oil intended for water cooled outboard motors, so-called outboard motor oil.
Control before starting For reasons of safety follow these recommendations! • Check that the support flange is not cracked due to fatigue or due to being tightened too much. Discard the support flange if it is cracked. • Ensure the locking nut has not lost its captive force.
Carburettor Your JONSERED product has been designed and manufactured to specifications that reduce harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in. To ensure that your unit is at peak performance and producing the least amount of harmful...
Page 17
Final setting of the idling speed T Adjust the idling speed with the screw T, if it is necessary to readjust. First turn the idle speed adjusting screw T clockwise until the cutting attachment starts to rotate/ move. Then turn, counter- clockwise until the cutting attachment stops.
Silencieux NOTER! Certains silencieux sont dotés d’un pot catalytique. Voir ”Caractéristiques techniques” pour déterminer si la machine est pourvue d’un pot catalytique. Le silencieux est conçu pour réduire le niveau sonore de la machine et pour éloigner de l’utilisateur les gaz libérés par la machine.
MAINTENANCE NOTE: Use only JONSERED replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically recommended by JONSERED.
NOTE! The noise pressure level at operator’s ear and vibrations on the handles are measured with all the approved cutting attachments for the machine. The table indicates the lowest and highest values. Approved accessories GT2125L: Thread blade shaft 3/8 Trimmer head...
If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Jonsered, at Sweden +46 36 14 65 00. WHERE TO GET WARRANTY SERVICE Warranty services or repairs shall be provided at all Jonsered authorized servicing dealers.
Page 22
Poly Trim >20mm >20mm 6 Nm X 10 – English...
Page 23
Trimmy H II 15 cm 6" 7,5 m ~ 3,7 m 15 cm 6" English –...
Page 24
Trimmy Hit Pro 15 cm 6" “Click” – English 7,5 m ~ 3,7 m 15 cm 6" 15 cm 6"...
Page 25
Trimmy VII 7,0 m 23" 12 cm 5" ~ 3,5 m 11" ~ 15 cm 6" 15 cm 6" English –...
Page 26
Tap-N-Go Pro 15 cm 6" “Click” ´*xty¶5s¨ – English 7,5 m ~ 3,7 m 15 cm 6" 15 cm 6"...