Advertisement
Table of Contents
- 1 Table of Contents
- 2 Introduction
- 3 Specifications and Limitations
- 4 For the Installer
- 5 Installation
- 6 Water Glass Filler Kit
- 7 Water Glass Filler Kit
- 8 Initial Start up
- 9 Gate Restrictor Plate
- 10 Cleaning and Sanitizing
- 11 Cleaning and Sanitizing
- Download this manual
See also:
Service & Parts Manual
Advertisement
Table of Contents
Related Manuals for Ice-O-Matic IOD150
Summary of Contents for Ice-O-Matic IOD150
- Page 1 SERVICE/INSTALLATION MANUAL ICE ONLY DISPENSERS MODELS-IOD150, IOD200 AND IOD250 Mile High Equipment 11100 East 45th Ave Denver, Colorado 80239 Part Number 9081305-01 Print Date 06/02...
-
Page 2: Table Of Contents
To the owner or user: This product manual is a source of information about the installation, start up, cleaning, maintenance and repair of the product. The IOD150, IOD200 and IOD250 are ice only counter top dispensers designed to use 22 inch wide and 30 inch wide respectfully Ice-O-Matic cubed ice machines as the source of ice. -
Page 3: Specifications And Limitations
Limited Warranty, resulting in a loss of warranty coverage. Specifications and design are subject to change without notice. The IOD150, IOD200 and IOD250 carry a 2-year Parts warranty and a 1 year Labor Warranty. These dispensers are designed to dispense cubed ice only. -
Page 4: For The Installer
These dispensers are designed to dispense cubed ice only. Do not use flaked, crushed or compressed ice forms. If an Ice-O-Matic ice machine is to be placed on top of the dispenser, an adapter will be required. Ice Machine Adapter... -
Page 5: Installation
Drip Tray Drain Fitting Note: This equipment must be installed with adequate backflow protection to comply with Federal, State and Local Codes. IOD150, IOD200, IOD250 Solvent Bond Hose Clamp Barb Adapter 1” Barb x ¾ MPT Drain Line 1-Inch Plastic Tubing with Insulation Page 4 Coupling ¾... -
Page 6: Water Glass Filler Kit
3. Connect field water supply to ¼ male flare fitting on tubing assembly. Apply water pressure and check all connections for leaks. Check faucet for proper operation. Maximum water pressure is 125 psi. Check that tubing assembly does not interfere with wiring or electrical connections. 4. Carefully reinstall panels on unit. IOD150, IOD200, IOD250 Page 5... -
Page 7: Water Glass Filler Kit
IOD200 and IOD250 Dimensions 6.125 Inches 3.125 Inches The water inlet tubing can be routed either from the back or from underneath the dispenser. If from the back, remove the back and bottom access panels. IOD150, IOD200, IOD250 Page 6... -
Page 8: Initial Start Up
Reinstall the splash panel and secure it with two Phillips head screws. Check for proper operation of the dispense system. Instruct the site manager regarding the requirements for maintaining, operation and sanitizing the dispenser. IOD150, IOD200, IOD250 Part number KBT15022 Part Number KBT25022 Part Number KBT25030... -
Page 9: Gate Restrictor Plate
Gate Restrictor Plate IOD150, IOD200, IOD250 CAUTION: Disconnect power to dispenser and ice machine before installing, removing or adjusting restrictor. ADJUSTMENT This plate may be adjusted as shown to reduce or increase the dispensing rate of ice, especially desirable when using glasses or other containers with small openings. Adjustment can be made by sliding up or down with the nuts loosened, to obtain the desired amount of restriction. -
Page 10: Cleaning And Sanitizing
Cleaning and Sanitizing IOD150, IOD200, IOD250 The sink, grill and splash panel area should be cleaned daily. The following dispenser maintenance should be performed at the intervals indicated: Daily (Or As Required) Remove foreign material from vending area drip tray to prevent drain blockage. -
Page 11: Cleaning And Sanitizing
13. Wipe the top edge of the ice hopper with the sanitizing solution, allow to air dry. 14. Pour in fresh, sanitary ice and replace the cover. Re-connect power to the dispenser and ice machine. IOD150, IOD200, IOD250 Page 10... - Page 12 B. Defective dispensing switch. C. Improper switch installation. Slushy Ice. Water in Hopper A. Blocked drain B. Unit not level C. Poor ice quality due to water quality or icemaker problems. D. Improper use of flaked ice. IOD150, IOD200, IOD250 Page 11...
- Page 13 Wiring Diagram IOD150, IOD200, IOD250 Page 12...