Blomberg DWT 23100 B Installation Manual
Dishwasher
Hide thumbs
Also See for DWT 23100 B:
- Use and care manual (36 pages) ,
- Installation manual (26 pages) ,
- Installation manual (26 pages)
Table of Contents
Advertisement
Dishwasher
Installation Manual
FOR MODELS
DWT 23100 B
DWT 23100 SS
DWT 23100 W
DWT 24100 B
DWT 24100 SS
DWT 24100 W
DWT 24400 SS ULTRA
DWT 24400 W ULTRA
DWT 25100 B
DWT 25100 SS
DWT 25100 W
DWT 25200 BWS
DWT 25200 SSWS
DWT 25200 WWS
DWT 25300 B
DWT 25300 W
DWT 25300 SS
DWT 25500 B
DWT 25500 W
DWT 25500 SS
DWT 54100 B
DWT 54100 FBI
USA
DWT 54100 SS
DWT 54100 W
DWT 54400 SS ULTRA
DWT 54400 W ULTRA
DWT 55100 B
DWT 55100 FBI
DWT 55100 SS
DWT 55100 W
DWT 55200 BWS
DWT 55200 FBIWS
DWT 55200 SSWS
DWT 55200 WWS
DWT 55300 FBI
DWT 55300 B
DWT 55300 W
DWT 55300 SS
DWT 55500 SS
DWT 57500 B
DWT 57500 FBI
DWT 57500 SS
DWT 57500 W
DWT 57550 SS
Advertisement
Table of Contents
Related Manuals for Blomberg DWT 23100 B
Summary of Contents for Blomberg DWT 23100 B
- Page 1 Dishwasher Installation Manual FOR MODELS DWT 23100 B DWT 25200 BWS DWT 54100 SS DWT 55200 WWS DWT 23100 SS DWT 25200 SSWS DWT 54100 W DWT 55300 FBI DWT 23100 W DWT 25200 WWS DWT 54400 SS ULTRA DWT 55300 B...
- Page 2 Cycle Select Start / Pause Half Load / Time Delay Tablet DWT 24400 SS ULTRA DWT 25200 WWS DWT 23100 B DWT 23100 SS DWT 24400 W ULTRA DWT 25300 B DWT 23100 W DWT 25100 B DWT 25300 W...
-
Page 3: Table Of Contents
To prevent accidents, which could cause serious injury or death, as well as machine damage read these instructions before installation and / or use. Contents 1. IMPORTANT SAFETY INSTRUCTIONS 1.1 INSPECT THE DISHWASHER 1.2 HOW TO CONTACT US 2. TOOLS WHICH MAY BE NEEDED 3. -
Page 4: Important Safety Instructions
INTRODUCTION WARNING Please read this installation manual and When installing the dishwasher, follow particularly the safety instructions completely basic precautions, including the and carefully. They will save you time following: and effort and help to ensure optimum The dishwasher installation must be dishwasher performance. -
Page 5: Inspect The Dishwasher
Dishwasher must be secured to adjacent Replacement - If the dishwasher is cabinetry using the brackets provided. replacing another dishwasher, check Failure to do this may cause damage to the existing dishwasher connections for property or bodily injury. compatibility with the new dishwasher, ... -
Page 6: Tools Which May Be Needed
2. TOOLS WHICH MAY BE NEEDED 3. MATERIALS WHICH MAY BE NEEDED (Additional materials may be required to comply with local codes) Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line. 90° elbow with 3/8” N.P.T. male threads on one leg, and sized to fit your water supply line (copper tubing/compression fitting, or braided hose) on the other leg. -
Page 7: Materials Supplied
4. MATERIALS SUPPLIED 4.1 PARTS SUPPLIED Parts for your dishwasher will come in several plastic bags. Check your parts bags shown to make sure you have all the parts as listed to the left. 4.2 MANUAL BAG The dishwasher comes with a manual bag containing: ... -
Page 8: Dishwasher Specifications
5. DISHWASHER SPECIFICATIONS 2 4 ” ( 6 1 2 4 ” ( 6 1 ” m 5.1 TECHNICAL FEATURES Load capacity 12 place settings Permissible water 4.35 - 145 psi (0.3 - 10 bars) pressure 120 V (volts), 12 A (amps), Electrical connection 60 Hz (hertz) Total power... -
Page 9: Enclosure Preparation
6. ENCLOSURE PREPARATION 6.1 ELECTRICAL PREPARATION WARNING The dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connected to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker rated for 15 amperes. 6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS WARNING Dishwasher must be secured to adjacent cabinetry using the mounting brackets... -
Page 10: Installing The Side Trim Strips
Adjust the front foot level with the adjusting wrench to balance and raise the dishwasher to the enclosure height. Adjust the rear foot level with a screwdriver to balance and raise the dishwasher to the enclosure height. Notice : Make sure the dishwasher is plumb and notice dishwasher can be placed with a small clearance under the counter top. -
Page 11: Preparing The Water Connection (A)
6.5 PREPARING THE WATER CONNECTION (A) Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder connections must be made before the water line is connected to the dishwasher’s water inlet valve. Water can also be supplied to the dishwasher by using a flexible braided hose line. -
Page 12: Drain Preparation
6.6 DRAIN PREPARATION The dishwasher drain hose may be connected to the drain plumbing in one of three ways (Figure A, B, C). Notice : Either one of the above methods must be used or the dishwasher will not operate properly. -
Page 13: Steam Protection Foil
6.7 STEAM PROTECTION FOIL Steam will form inside the dishwasher during operation. At the end of the cycle, when the dishwasher door is opened, it is required to use a steam protection foil to prevent any steam from collecting on the underside of the counter top. 6.6.2 FITTING THE PROTECTION FOIL Before applying the steam protection foil to the underside of the countertop, clean the area with... -
Page 14: Placement Of Dishwasher Into The Opening
7. PLACEMENT OF DISHWASHER INTO THE OPENING Now place the dishwasher into the opening and get ready to connect all hoses and electrical connections. CAUTION Make sure all hoses are pulled through the side opening of the cabinet, no hoses are kinked and all slack is taken out as shown in the above figure. - Page 15 7.1.2 PREPERATION OF WATER SUPPLY Left side water supply connection Before pushing the dishwasher in to the cabinet you must place water supply hoses into the channel of the dishwasher (Figure A). Place the supplied clips into the channel (Figure B) so that you can move these clips along the channel (Figure C) and fix by pressing on (Figure D) so that you can keep the water supply hose in the...
- Page 16 After installing one clip for each side push the dishwasher into the cabinet (Figure E). Note that while pushing the dishwasher into the cabinet, water supply hose must move in the channel to the front (Figure F). Fix the second clip (Figure G).
- Page 17 7.1.3 WATER SUPPLY CONNECTION Water supply may be connected to the dishwasher in one of two ways: With metal braided hose. With copper tubing. CAUTION Hot water supply line: Use minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line.
-
Page 18: Readjusting Foot Levels
7.2 READJUSTING FOOT LEVELS Now that the dishwasher is in the (3,5mm) Ø " cabinet you must readjust the feet to bring the dishwasher up to the required Ø " (3,5mm) height and attach it underneath the countertop. 1. Readjust the front foot levels with adjusting wrench to balance the dishwasher and raise it up under the countertop, make sure the unit is level. -
Page 19: Installing The Outer Door
If the enclosure height is below 33 1 / 16 ” (840mm) use only “o” labelled toe kick (toe kick without slots). Installation should be done following the steps illustrated in the Figures A, B and C respectively. 1.Bend tabs on toe kick (o) inwards (A). - Page 20 2. To take the plastic bracket out, remove the screws on it. Screws will be used in 5th step again. (Figure B). 3. Mark the wooden door as shown in the drawing (Figure C). 4. Place the plastic mounting brackets over the marked holes and the side tabs must be flush with the edge of the wooden door (Figure D).
- Page 21 5. Attach the two mounting brackets to the wooden door with 4 screws (Ø 1 / 8 ” x 5 / 8 ” (Ø 3.5mm x 14mm) (3,5mm) Ø " (Figure A). 6. Mount the wooden door onto the dishwasher with the plastic mounting brackets which you have attached (Figure B).
- Page 22 8. Using the four screws Ø 3 / 16 ” x 1 11 / 16 ” (Ø 4mm x 43mm) provided, attach the wooden door to the dishwasher at position 1 and 4 (Figure A). Ø 3 / 16 " (4mm) 9.
-
Page 23: Adjusting Door Tension With Custom Wooden Door
11. Check whether the bottom of the door hits the toe kick of the kitchen cabinet (A). 11.1. If the door hits the toe kick cut the necessary section out of the toe kick (B). 11.2. Apply silicon or sealant to the cut edge of the kitchen cabinet toe kick or paint so it does not absorb moisture. - Page 24 Notice : If you have a European kitchen or want to install a wooden toe kick to match your kitchen, please refer to one of the two drawings given below. Follow the same instructions on the brackets as for the removable toe kick. Installation should be done following the steps illustrated in the figures A, B, C, D respectively.
-
Page 25: Installer Checklist
8. INSTALLER CHECKLIST 10. SELF HELP HINTS: Your installer must have completed and The screen does not come on: checked the following: Check to make sure the breaker to the The dishwasher is square and level. dishwasher is in the on position. ... - Page 26 17 9077 01 00-AC-USA...