HUSTLER Super Mini Z Parts Manual page 25

Pump Belt and Pulley Installation
INDEX
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
1. Torque to 45-48 ft.-lbs.
2. Torque to 12-15 ft.-lbs.
3. Do not torque Item 18 (NT .750-10 HX NL ZN), Item 16 (368860 Pump
Idler Arm) should pivot freely.
4. Apply grease at zerks (see owner's manual).
5. Electric clutch burnishing procedure: After installing a new clutch, it
is important to burnish the clutch to insure maximum deck clutch life. In
an open area with no bystanders, set the engine speed to half throttle.
302620 8/06
SERVICE MFG.
PART NO. PART NO.
783761 783761
212076 212076
797654 797654
791251 791251
787366 787366
783829 783829
785659 785659
083196 083196
782466 782466
768127 768127
366765 366765
016527 016527
767962 767962
008193 008193
784918 784918
015495 015495
368860 368860
025296 025296
061101 061101
786848 786848
028118 028118
781872 781872
781302 781302
786533 786533
787408 N/A
778217 N/A
036244 N/A
767954 N/A
054502 N/A
055939 N/A
362392 N/A
778738 N/A
768515 N/A
024927 N/A
748681 N/A
QTY DESCRIPTION
1 SUPER Z SINGLE PULLEY
1 KEY 1/4 SQ X 1.50 LONG
1 FW 1.156 X 1.750 X .250 ZY
1 CLUTCH PIGTAIL HARNESS (DIODE)
1 WARNER Z CLUTCH
1 FW .460X 1.750X .250 ZNYC
1 CS .437-20 X 2.50 HX G5 ZNYC
4 SS .312-18 X .750 SQ-HD ZN
2 PULLEY & FAN BDP-21
2 KEY 5MM X 30MM RADIUS ENDS
1 CLUTCH ANCHOR ANGLE
2 CS .500-13 X 1.00 HX G5 ZNYC
4 FW .531 X 1.063 X .090 SAE HD ZN
2 NT .500-13 HX G5 ZNYC
1 RUBBER BUMPER
1 STRAIGHT GREASE FITTING
1 PUMP IDLER ARM
1 FW .760 X 1.625 X .08 ZN
1 NT .750-10 HX NL ZN
1 IDLER PULLEY
1 FW .62 X 1.00 X.134
1 CS .625-11 X 1.25 HX G5 ZN
1 IDLER SPRING
1 A-SEC PUMP IDLER BELT
1 CLUTCH
1 CS .437-20 X 2.25 G5 ZNYC
1 CS .375-16 X 1.000 HX G5 ZN
2 FW .406 X .812 X .060 SAE HD ZN
1 NT .375-16 HX GRD 5 ZN
1 CS .250-20 X .750 HX G5 ZN
1 CLUTCH ANCHOR BRACKET
1 .312 WIRING CLAMP
1 FW .281 X .625 X .051/.080 HD ZN/YL
1 NT .250-20 HX GR.5 ZN
1 GM .75 X 1.35 X 1.06 X .18 GROMMET
NOTES:
4-11
ZN