HUSTLER 927053 Owner's Manual page 34

Hustler lawn mower owner's manual
Table of Contents

Advertisement

Hustler Z/Super Z/Hustler ATZ
Maintenance Schedule
Refer to Fig. 4-16, 4-18, 4-19, 4-20 & 4-21
WEEKLY MONTHLY ANNUALLY OR
SERVICE AT
OR 50
OR 100
500
INTERVALS INDICATED
HOURS
HOURS
HOURS
Verify safety start interlock system
Daily
Check coolant level
Daily
Visually inspect unit for loose
hardware and/or damaged parts
Daily
Visually inspect tires
Daily
Check oil level, engine (1)
Daily or every 4 hrs.
Clean air intake screen (8)
Daily or every 4 hrs.
Clean oil heat exchanger (8)
Daily or every 4 hrs.
Check radiator screen (8)
Daily or every 4 hrs.
Check fuel level
Daily
Blades - sharpen & securely fastened
Daily
Discharge chute - securely in place &
in lowest position
Daily
Clean engine and pump compartment
Daily
Replace air cleaner paper element (5)
As needed
Grease deck pusher arms
x
Grease pump idler
x
Grease deck height pivots
x
Grease gauge wheel bearings
x
Change engine oil & filter (1) (4)
x
Clean cylinder and head fins (a)
x
Check battery connections
x
Check tire pressure with a gauge
x
Check hydraulic oil level
x
Clean engine exterior (a)
x
Clean and regap spark plugs (a)
x
Check pump and deck belt tension
& condition (6)
x
Check fuel and hydraulic lines (7)
x
Check fuel valve and grommets (7)
x
Tighten lug nuts on wheels (2)
x
Change fuel filter
x
Clean or replace hydraulic fill cap
x
Change hydraulic filter and oil (3)
x
Grease deck spindle housings
x
Replace spark plugs
x
Drain & replace engine coolant
x
Clean radiator core (8)
x
Check ROPS mounting hardware (9)
x
NOTES:
1.
Initial oil change is after 5 hours of operation. Thereafter,
change oil after every 40 hours operation. Change more often
under dusty or dirty conditions and during hot weather periods.
2.
Torque initially and after first 2 hours of operation.
3.
Perform initial hydraulic filter change after 50 hours (one week)
of operation.
4.
Change engine oil filter per the engine manufacturer’s
recommendations. Refer to Engine Owner’s Manual for
recommendations and other maintenance items.
5.
Service more often under dusty or dirty conditions. Use caution
when servicing to prevent dust contamination in the engine.
Do not clean filter element. Replace with a new one.
6.
Pump drive belt only - Inspect every 100 hours and replace
if worn or cracking is noticed. Otherwise, replace every 400
hours or 2 years whichever comes first.
7.
Check fuel line hoses, fuel valve and grommet for any cracks
or leaks.
8.
More often under dusty or dirty conditions and during hot
weather.
9.
Inspect ROPS after the first 20 hours of operation and then
after every 500 hours of operation or yearly whichever comes
first.
REFERENCES:
a
— Refer to Engine Owner’s Manual
NOTE: After completing maintenance cycle (500 hours), repeat cycle.
Hustler Z Shibaura Diesel Maintenance Schedule
Refer to Fig. 4-17, 4-18, 4-19 & 4-20
WEEKLY MONTHLY ANNUALLY OR
SERVICE AT
OR 50
OR 100
500
INTERVALS INDICATED
HOURS
HOURS
HOURS
Check coolant level
Daily
Verify safety start interlock system
Daily
Visually inspect unit for loose
hardware and/or damaged parts
Daily
Visually inspect tires
Daily
Check oil level, engine (1)
Daily or every 4 hrs.
Clean air intake screen (8)
Daily or every 4 hrs.
Clean oil heat exchanger (8)
Daily or every 4 hrs.
Check radiator coolant level
Daily
Check fuel level
Daily
Blades - sharpen & securely fastened
Daily
Discharge chute - securely in place &
in lowest position
Daily
Check air cleaner service indicator (5)
Daily
Clean engine and pump compartment
Daily
Visually inspect radiator core (8)
x
Grease deck pusher arms
x
Grease pump idler
x
Grease deck height pivots
x
Grease gauge wheel bearings
x
Change engine oil & filter (1) (4)
x
Check battery connections
x
Check tire pressure with a gauge
x
Check hydraulic oil level
x
Clean engine exterior (a)
x
Check pump and deck belt tension
& condition (6)
x
Check fuel and hydraulic lines (7)
x
Check fuel valve and grommets (7)
x
Tighten lug nuts on wheels (2)
x
Change fuel filter
x
Clean or replace hydraulic fill cap
x
Change hydraulic filter and oil (3)
x
Grease deck spindle housings
x
Clean radiator core (8)
x
Drain & replace engine coolant
x
Check ROPS mounting hardware (9)
x
NOTES:
1.
Initial oil change is after 50 hours of operation. Thereafter,
change oil after every 100 hours operation. Change more
often under dusty or dirty conditions and during hot weather
periods.
2.
Torque initially and after first 2 hours of operation.
3.
Perform initial hydraulic oil and filter change after 50 hours
(one week) of operation.
4.
Change engine oil filter per the engine manufacturer’s
recommendations. Refer to Engine Owner’s Manual for
recommendations and other maintenance items.
5.
Service more often under dusty or dirty conditions. Use caution
when servicing to prevent dust contamination in the engine.
Do not clean filter element. Replace with a new one.
6.
Pump drive belt only - Inspect every 100 hours and replace
if worn or cracking is noticed. Otherwise, replace every 400
hours or 2 years whichever comes first.
7.
Check fuel line hoses and fuel valve for any cracks or leaks.
8.
More often under dusty or dirty conditions and during hot
weather.
9.
Inspect ROPS after the first 20 hours of operation and then
after every 500 hours of operation or yearly whichever comes
first.
REFERENCES:
a
— Refer to Engine Owner’s Manual
NOTE: After completing maintenance cycle (500 hours), repeat cycle.
Page 33

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents