Table of Contents
Related Manuals for Husqvarna 327HE3X
Summary of Contents for Husqvarna 327HE3X
- Page 1 Operator′s manual 327HDA65 X-series 327HE3 327HE4 X-series X-series Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
-
Page 2: Key To Symbols
Symbols WARNING! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual. -
Page 3: Table Of Contents
WARNING! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual. -
Page 4: Introduction
Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets. -
Page 5: What Is What
327HE4 What is what? Cutter Grease nipple and plug for filling lubricant. Bevel gear Blade guard (327HDA65) Shaft Front handle (327HDA65, 327HE3) Front handle (327HE4) Throttle control Stop switch 10 Throttle lock 11 Harness support hook (327HE4) 12 Cylinder cover 13 Starter handle 14 Fuel tank 15 Choke control... -
Page 6: General Safety Precautions
6 – English Personal protective equipment IMPORTANT! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual. -
Page 7: Machine's Safety Equipment
See instructions under the heading Start. Start the hedge trimmer and apply full throttle. Release the throttle trigger and check that the blades stop and remain stationary. If the blades move when the throttle trigger is in the idle –... - Page 8 GENERAL SAFETY PRECAUTIONS position then the carburettor idle setting must be adjusted. See instructions under the heading Maintenance. Stop switch Use the stop switch to switch off the engine. Start the engine and make sure the engine stops when you move the stop switch to the stop setting. Hand guard (327HDA65, 327HE3) The hand guard prevents hands from coming into contact...
-
Page 9: Gear Housing
GENERAL SAFETY PRECAUTIONS a spark arrestor mesh. Check whether the muffler on your machine is fitted with this kind of mesh. For mufflers it is very important that you follow the instructions on checking, maintaining and servicing your machine. Never use a machine that has a faulty muffler. Regularly check that the muffler is securely attached to the machine. -
Page 10: Assembly
Fit the handle using two screws. Fitting the cutting head (327HDA65) It is important that the hedge trimmer is laid on a flat surface when you fit the cutting head. Otherwise the cutting head may not be fitted straight. Fit the cutting head to the shaft. CAUTION! Make sure the drive shaft inside the shaft engages with the recess in the cutting head. -
Page 11: Adjusting The Harness
Adjusting the harness (327HE4) You should always use the harness with the machine to give maximum control over the machine and reduce the risk of fatigue in your arms and back. Put on the harness. Hook the machine onto the harness support hook. Adjust the length of the harness so that the support hook is roughly level with your right hip. -
Page 12: Fuel Handling
When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For best results and performance use HUSQVARNA two-stroke engine oil, which is specially formulated for our air-cooled two-stroke engines. • Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW). -
Page 13: Fuelling
Mixing • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol. -
Page 14: Starting And Stopping
Check before starting • Inspect the working area. Remove any objects that could be thrown out. • Check the cutting attachment. Never use blades that are dull, cracked or damaged. • Check that the machine is in perfect working order. Check that all nuts and screws are tight. - Page 15 STARTING AND STOPPING CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. CAUTION! Do not put any part of your body in marked area.
-
Page 16: Working Techniques
General working instructions IMPORTANT! This section takes up the basic safety precautions for working with a hedge trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop. -
Page 17: Basic Working Techniques
Make sure that the tip does not touch the ground. • Do not rush the work, but work steadily until all the branches have been cut back cleanly. Changing the hedge trimmer angle (327HE3, 327HE4) • Loosen the knob on the shaft (clockwise). -
Page 18: Transport Position
(327HE4) Once the work has been completed fold the cutting unit back against the shaft to simplify transport and storage of the hedge trimmer. Turn off the engine. Loosen the knob on the shaft (clockwise). Grip the handle on the cutting unit and angle the cutting unit upwards. -
Page 19: Maintenance
Carburettor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhaust... -
Page 20: Cooling System
cause fire if directed against dry and combustible material. Some mufflers are equipped with a special spark arrestor mesh. If your machine has this type of muffler, you should clean the mesh at least once a week. This is best done with a wire brush. -
Page 21: Air Filter
See instructions under the heading Oiling the air filter. Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact. -
Page 22: Cleaning And Lubrication
MAINTENANCE Cleaning and lubrication Clean any resin and plant residue from the blades using cleaning agent 531 00 75-13 (UL22) before and after using the machine. Lubricate the blade bars with special grease, part no. 531 00 75-12 (UL 21) before long periods of storage. 22 –... -
Page 23: Maintenance Schedule
Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. -
Page 24: Technical Data
Technical data Engine Cylinder displacement, cm Cylinder bore, mm Stroke, mm Idle speed, rpm Recommended max. speed, rpm Max. engine output, acc. to ISO 8893, kW/ rpm Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug Electrode gap, mm Fuel and lubrication system Manufacturer/type of carburettor... -
Page 25: Ec-Declaration Of Conformity
Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare under sole responsibility that the hedge trimmers Husqvarna 327HDA65 from 2009’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the standards or or other normative documents following the provisions in the COUNCIL’S DIRECTIVES:... - Page 28 1151377-26 ´®z+SEh¶6Y¨ ´®z+SEh¶6Y¨ 2009-05-11...