Page 1
Oper ator’s manual (EPA) 324L X-series 324LD X-series Please r ead the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h understand the instructions before using the machine.
Wear sturdy, non-slip boots. 2 – English KEY TO SYMBOLS Only use non-metallic, flexible cutting attachments, i.e. trimmer heads with trimmer cord. Other symbols/decals on the machine refer to special certification requirements for certain markets. Switch off the engine by moving the stop switch to the STOP position before carrying out any checks or maintenance.
WARNING! A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of this operator’s manual.
Dear customer! Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant.
Personal protective equipment IMPORTANT! A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of this operator’s manual.
GENERAL SAFETY PRECAUTIONS Machine′ ′ ′ ′ s safety equipment This section describes the machine′s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is what?” section to locate where this equipment is positioned on your machine.
Page 8
GENERAL SAFETY PRECAUTIONS Vibration damping system Your machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier. Use of incorrectly wound cord or an incorrect cutting attachment increases the level of vibration. See instructions under the heading Cutting equipment.
• Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the correct length. • To increase the life of the cord it can be soaked in water for a couple of days.
Slide the spacer into the slot in the loop handle. • Fit the nut, knob and screw. Do not overtighten. • Now adjust the trimmer to give a comfortable working position. Tighten the bolt/knob. Assembling and dismantling the two-piece shaft (324LDx) Assembly: •...
(Caution! left-hand thread). • Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover.
When the machine is new the engine oil should be changed after the first month or after 10 hours of operation. • For the best result and function use HUSQVARNA engin oil. • When HUSQVARNA engine oil is not available another high grade engine oil can be used.
Page 13
Fueling WARNING! Taking the following precautions, will lessen the risk of fire: Do not smoke or place hot objects near fuel. Always shut off the engine before refuelling. Always stop the engine and let it cool for a few minutes before refuelling. When refuelling, open the fuel cap slowly so that any excess pressure is released gently.
• Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked. • Never use the machine without a guard nor with a defective guard.
STARTING AND STOPPING Warm engine Ignition: Set the stop switch to the start position. Choke: Put the choke in working position. Primer bulb: Press the air purge repeatedly until fuel begins to fill the bulb. The bulb need not be completely filled. WARNING! When the engine is started with the choke in either the choke or start throttle positions the cutting attachment will start to...
General working instructions IMPORTANT! This section takes up the basic safety precautions for working with a trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop.
Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. CAUTION! This technique increases the wear on the cord.
Carburetor WARNING! The complete clutch cover and shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury. Function • The carburetor governs the engine’s speed via the throttle control. Air and fuel are mixed in the carburetor. •...
Cooling system To keep the working temperature as low as possible the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter. 2 Fins on the flywheel. 3 Cooling fins on the cylinder. 4 Cylinder cover (directs cold air over the cylinder).
Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact. Put the filter in a plastic bag and pour the filter oil over it.
Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked. Check that the trimmer head is undamaged and not cracked. Replace the trimmer head if necessary. Check that the locking nut of the cutting equipment is tighten correctly.
Technical data Engine Cylinder displacement, cu.in/cm Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Recommended max. fast idle speed, rpm Speed of output shaft, rpm Max. engine output, acc. to ISO 8893, kW/ rpm Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug...
Page 23
Saw attachment without shaft PA The accessories have been developed mainly for the Husqvarna 125LD trimmer, but can also be used in combination with the specified power heads and have been evaluated to applicable ISO- and EN safety requirement standards by the Swedish Machinery Testing Institute.
MANUFACTURER′ ′ ′ ′ S WARRANTY COVERAGE The emissions control system is warranted for two years. If any emissions-related part on your equipment is defective, the part will be repaired or replaced by Husqvarna Forest & Garden. OWNER′ ′ ′ ′ S WARRANTY RESPONSIBILITIES •...
Page 25
EPA may not be used. The use of any non-exempted add-on or modified parts will be grounds for disallowing a warranty claim. Husqvarna Forest & Garden will not be liable to warrant failures of warranted parts caused by the use of a non- exempted add-on or modified part.
Page 26
Super Auto II Super Auto II 1 " 4,0 m 15 cm ~2,0 m 6 " 6,5 ' 15 cm 6 "...