Husqvarna 322E/325E-X Operator's Manual

Husqvarna trimmer operator's manual

Advertisement

322E/325E-X
Operator's manual
Read through the Operator's manual carefully and
understand the content before using the machine.
(CARB, EPA)
101 89 75-95

Advertisement

Table of Contents
loading

Summary of Contents for Husqvarna 322E/325E-X

  • Page 1 322E/325E-X Operator’s manual Read through the Operator‘s manual carefully and understand the content before using the machine. (CARB, EPA) 101 89 75-95...
  • Page 2: Symbol Explanation

    Symbols WARNING! The edger can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Read through the Operator‘s Manual carefully and understand the content before using the machine. Always use • A protective helmet where there is a risk of falling objects •...
  • Page 3: Table Of Contents

    Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. Maintenance, replacement, or repair of the emission control devices and systems may be performed by any nonroad engine repair establishment or individual.
  • Page 4: Safety Instructions

    Personal protective equipment IMPORTANT INFORMATION • An edger used incorrectly or carelessly can become a dangerous tool, that can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the content of this manual. •...
  • Page 5 4. Vibration damping system Your machine is equipped with a vibration damping system, which is designed to give as vibration-free and comfortable use as possible. The use of incorrect cutting equipment increases the level of vibration. The machine’s vibration damping system reduces the transfer of vibrations between the engine unit/cutting equip- ment and the machine’s...
  • Page 6: Control, Maintenance And Service Of The Machine's Safety Equipment

    Control, maintenance and service of the machine‘s safety equipment IMPORTANT INFORMATION • All service and repairs to the machine require special training. • This applies especially to the machine‘s safety equip- ment. If the machine does not meet any of the controls listed below you should contact your service work- shop.
  • Page 7: Cutting Equipment

    6. Cutting equipment Two basic rules: 1) Only use the cutting and guard equipment we recommend! See chapter “Technical data“. 2) Check the cutting equip- ment with regard to damage and crack formation. Damaged cutting equipment should always be replaced. WARNING! Always stop the engine before starting work on any part of the cutting equipment.
  • Page 8: General Safety Instructions

    General safety instructions IMPORTANT INFORMATION • The machine is only designed for cutting the edges of lawns. • The only accessories to be used with the engine unit as a drive source are the cutting units we recommend in the chapter “Technical data“ . •...
  • Page 9: Transport And Storage

    Start WARNING! When the engine starts with the choke lever in the choke or starter throttle position the cutting tool (blade or trimmer) starts to rotate immediately. • The complete clutch cover with shaft must be fitted before the machine is started,...
  • Page 10: General Working Instructions

    General working instructions IMPORTANT INFORMATION • This section takes up the basic safety precautions for working with the edger. • If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop. •...
  • Page 11 Safety instructions after completing work • Ensure the blade has stopped before cleaning, carrying out repairs or an inspection. Remove the spark plug cable from the spark plug. • Wear heavy-duty gloves when carrying out repairs on the edger. • Store the machine out of reach of children.
  • Page 12: What Is What

    What is what on the edger? Blade Grease filler cap Angle gear Blade guard Shaft Loop handlebar Throttle Stop switch Throttle trigger lock 10. Cylinder cover 11. Starter handle 12. Fuel tank 13. Choke 14. Air purge – English WHAT IS WHAT? 15.
  • Page 13: Assembly

    Assembling the loop handlebar • Position the handle on the shaft. Note that the handle must be mounted below the arrow on the shaft. • Fit the bolt, securing plate and wing nut as shown in the diagram. • Tighten the wing nut. Assembling the angle gear •...
  • Page 14: Fuel Handling

    • When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For the best results use HUSQVARNA two-stroke oil, which has been specially developed for two-stroke engines. Mixing ratio 1:50 (2%). • Never use two-stroke oil...
  • Page 15: Start And Stop

    WARNING! When the engine starts with the choke lever in the choke or starter throttle position the cutting tool (blade or trimmer) starts to rotate immediately. Start Press the machine body against the ground using your left hand (NOTE! Not your foot).
  • Page 16: Maintenance

    Carburetor Your Husqvarna product has been designed and manufac- tured to specifications that reduce harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in. To ensure that your unit is at peak perfor-...
  • Page 17 Final setting of the idling speed T Adjust the idling speed with the screw T, if it is necessary to readjust. First turn the idle speed adjusting screw T clockwise until the cutting attachment starts to rotate/ move. Then turn, counter-clockwise until the cutting attachment stops.
  • Page 18: Muffler With Catalytic Converter

    Muffler with catalytic converter A muffler fitted with a catalytic converter reduces the extent of the following substances in the exhaust fumes: • Hydrocarbons (HC). Some hydrocarbons in gasoline and the exhaust are carcinogenic. • Nitric oxides (NO). Irritating for the breathing air-ways. •...
  • Page 19: Air Filter

    If the machine is used in dusty conditions the air filter should be soaked in oil, see the section on “ Oiling the air filter “. Oiling the air filter Always use HUSQVARNA filter oil, order no. 503 47 73- 01. The filter oil contains a solvent to make it spread evenly through the filter.
  • Page 20: Maintenance Schedule

    NOTE: Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically recommended by HUSQVARNA.
  • Page 21: Technical Data

    Technical data Engine Cylinder capacity, cu. in/cm Cylinder bore, inch/mm Stroke length, inch/mm Recommended max. speed, rpm Idling speed, rpm Speed of output axle, rpm Max. engine output, acc. to ISO 8893 Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug Electrode gap, inch/mm...
  • Page 22: Federal And California Emission Control Warranty Statement

    REPAIR OR REPLACEMENT OF PARTS Repair or replacement of any warranted part will be performed at no charge to the owner at an approved Husqvarna Forest & Garden servicing dealer. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest &...
  • Page 23 NOTES English –...
  • Page 24 ´*2£[¶5d¨ 1999W37...

This manual is also suitable for:

322e325e-x

Table of Contents