Related Manuals for Husqvarna 1153286-26
Summary of Contents for Husqvarna 1153286-26
- Page 1 Operator′s manual 324LD X-series Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
-
Page 2: Key To Symbols
2 – English KEY TO SYMBOLS Wear sturdy, non-slip boots. Only use non-metallic, flexible cutting attachments, i.e. trimmer heads with trimmer cord. Noise emission to the environment according to the European Community’s Directive. The machine’s emission is specified in chapter Technical data and on label. -
Page 3: Table Of Contents
WARNING! A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of this operator’s manual. -
Page 4: Introduction
Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets. -
Page 5: What Is What
What is what? Trimmer head Bevel gear Grease filler cap, bevel gear Cutting attachment guard Shaft Loop handle Stop switch Throttle control Throttle lockout 10 Cylinder cover 11 Starter handle WHAT IS WHAT? 12 Air purge 13 Fuel tank 14 Choke control 15 Air filter cover... -
Page 6: General Safety Precautions
6 – English Personal protective equipment IMPORTANT! A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of this operator’s manual. -
Page 7: Machine's Safety Equipment
GENERAL SAFETY PRECAUTIONS CLOTHING Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. Secure hair so it is above shoulder level. - Page 8 GENERAL SAFETY PRECAUTIONS be checked. See instructions under the heading Maintenance. Stop switch Use the stop switch to switch off the engine. Start the engine and make sure the engine stops when you move the stop switch to the stop setting. Cutting attachment guard This guard is intended to prevent loose objects from being thrown towards the operator.
- Page 9 GENERAL SAFETY PRECAUTIONS Muffler The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user. A muffler fitted with a catalytic converter is also designed to reduce harmful exhaust gases. In countries that have a warm and dry climate there is a significant risk of fire.
-
Page 10: Cutting Equipment
• Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the correct length. • To increase the life of the cord it can be soaked in water for a couple of days. -
Page 11: Assembly
Slide the spacer into the slot in the loop handle. • Fit the nut, knob and screw. Do not overtighten. • Now adjust the trimmer to give a comfortable working position. Tighten the bolt/knob. Assembling and dismantling the two-piece shaft Assembly: •... -
Page 12: Fitting Other Guards And Cutting Attachments
• • • Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover. To dismantle, follow the instructions in the reverse order. -
Page 13: Fuel Handling
When the machine is new the engine oil should be changed after the first month or after 10 hours of operation. • For the best result and function use HUSQVARNA engine oil. • When HUSQVARNA engine oil is not available another high grade engine oil can be used. - Page 14 When the oil level is low, top up using engine oil to the edge of the oil refill hole. Only use recommended engine oil. Fuelling WARNING! Taking the following precautions, will lessen the risk of fire: Do not smoke or place hot objects near fuel.
-
Page 15: Starting And Stopping
• Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked. • Never use the machine without a guard nor with a defective guard. -
Page 16: Warm Engine
Warm engine Ignition: Set the stop switch to the start position. Choke: Put the choke in working position. Primer bulb: Press the air purge repeatedly until fuel begins to fill the bulb. The bulb need not be completely filled. WARNING! When the engine is started with the choke in either the choke or start throttle positions the cutting attachment will start to rotate... -
Page 17: Working Techniques
General working instructions IMPORTANT! This section takes up the basic safety precautions for working with a trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop. -
Page 18: Basic Working Techniques
WORKING TECHNIQUES Cutting • The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep the cord parallel to the ground when cutting. Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool. -
Page 19: Maintenance
Carburettor WARNING! The complete clutch cover and shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury. Function • The carburettor governs the engine’s speed via the throttle control. Air and fuel are mixed in the carburettor. -
Page 20: Cooling System
Cooling system To keep the working temperature as low as possible the machine is equipped with a cooling system. The cooling system consists of: Air intake on the starter. Fins on the flywheel. Cooling fins on the cylinder. Cylinder cover (directs cold air over the cylinder). Clean the cooling system with a brush once a week, more often in demanding conditions. -
Page 21: Bevel Gear
See instructions under the heading Oiling the air filter. Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact. -
Page 22: Maintenance Schedule
Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked. Check that the trimmer head is undamaged and not cracked. Replace the trimmer head if necessary. Check that the locking nut of the cutting equipment is tighten correctly. -
Page 23: Technical Data
EN ISO 11806 and ISO 22867, m/s Equipped with trimmer head (original), left/right Note 1: Noise emissions in the environment measured as sound power (L EC. Reported sound power level for the machine has been measured with the original cutting attachment that gives the highest level. -
Page 24: Ec-Declaration Of Conformity
Edger attachment with shaft Saw attachment with shaft PA 1100 Trimmer attachment with shaft TA 850 The following attachments have been developed mainly for the Husqvarna 125LD trimmer, but can also be used with the specified models. Approved accessories Cultivator attachment CAC... - Page 25 Super Auto II Super Auto II 1 " 4,0 m 15 cm ~2,0 m 6,5 ' 15 cm 6 " 6 "...
- Page 27 8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...
- Page 28 4,25 m 4,25 m 15 cm 6" 15 cm 6"...
- Page 29 T35, T35x 15 cm 6" 8,5 m 10 cm 4" 4,3 m "Clic"...
- Page 36 Original instructions 1153286-26 ´®z+U<^¶6_¨ ´®z+U<^¶6_¨ 2010-03-31...