Download Print this page

Husqvarna R 43 Operator's Manual page 11

Husqvarna lawn mower operator's manual

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 1
Starting & Stopping R 43
Starting
1. Connect the spark plug lead.
2. Move the Engine Speed Control to the FAST
'
' position before starting.(G1)
3. Pull the operator presence control (OPC) to release
the brake on the engine and the blade.(G2)
4. Pull the recoil starter fully towards you until you feel
the full resistance, return the handle slowly then pull
the handle firmly towards you to its full extent.(G3)
5. After the engine has started, allow to run for 30
seconds before commencing to use.
Stopping
1. Release the OPC lever.(G2)
THROTTLE CONTROL (if fitted)
1. Fig. G4 represents the FAST (run) position.
2. Fig. G5 represents the SLOW (idle) position.
Starting & Stopping R 43S
Starting
1. Follow steps 1-2 for the R 43.
2. Pull the operator presence control (OPC) to release
the brake on the engine and the blade.(G6).
3. Follow steps 4-5 for the R 43.
Engaging the Drive
1. Forward drive is engaged and disengaged with
the Powerdrive lever at the top of the handle.(G7)
2. Releasing the Powerdrive Lever stops the
forward drive automatically.
Stopping
1. Release the powerdrive lever.(G7)
2. Release the OPC lever.(G6)
Starting & Stopping R 43SE
Starting
1. Follow steps 1-3 for the R 43S
2. Turn the key and hold until the engine starts.(G8) The
key will return to the original position when released.
3. If the engine fails to start when you turn the key
your battery may need charging.
Engaging the Drive - See R 43S
Stopping - See R 43S
IMPORTANT
Release the Operator Presence Control, to stop
the engine, wait until the blade has stopped and
disconnect the spark plug lead:-
- before clearing a blockage;
- before checking, cleaning or working on the
appliance
IMPORTANT
Never use water for cleaning your lawnmower. Do
not clean with chemical, including petrol, or solvents
- some can destroy critical plastic parts.
Cleaning
• Disconnect the spark plug lead.
• Turn machine on it's side with the exhaust uppermost.
1. Remove grass from under the deck with a
brush.(L1 and L2)
2. Using a soft brush - remove grass clippings from
the engine air intakes and exhaust (L3), cutting
height adjustment area, around the wheels (L4)
and the grass collector.
3. Wipe over the surface of your lawnmower with a
dry cloth.
Use
How to Mow
• Due to engine lubrication limitations, the
mower should not be used on slopes in
excess of 30°.
1. Start mowing from the outside edge of the lawn,
mowing in strips in alternate directions
2. Mow twice a week in the growing season, your
lawn will suffer if more that one third of its length
is cut at one time and this may also result in poor
collection.
Please Note:-
Do not overload your Lawnmower
When mowing in long thick grass a first cut with the
cutting height adjusted to its highest setting, see
Cutting Height, will help reduce engine overload
and will help prevent damage to your lawnmower.
Cutting Height Adjustment
1. Pull the height adjustment lever away from the
location slots and move it to the selected
position.(H).
Using as a mulcher
1. Your lawnmower is supplied with a mulching plug.
2. Stop your lawnmower as described in Use -
starting and stopping, and disconnect the spark
plug.
3. Lift safety flap. Twist and slide mulching plug into
rear discharge chute. (J)
4. Ensure mulching plug is securely fitted. (K)
5. The mulching plug prevents grass from being
collected by blocking the collection chute on the
underside of the deck.
6. Ensure the safety flap is positioned correctly.
Maintenance
Cutting System
Removing the Blade
• Disconnect the spark plug lead.
• Turn machine on it's side with the exhaust uppermost.
1. Use spanner to loosen blade bolt by turning anti-
clockwise.(M)
2. Remove the blade bolt, blade and spacer washer.
3. Inspect for damage and clean as necessary.
Fitting the Blade
1. Fit the blade to the machine with the sharp edges
pointing away from the machine.
2. Re-assemble blade bolt through blade and
spacer washer.
3. Hold firmly and tighten blade bolt firmly with a
spanner. Do not over tighten.
IMPORTANT
Do not attempt any maintenance on your
lawnmower when the engine is hot.
Always handle the blade with care - sharp edges
could cause injury. USE GLOVES. Renew your
metal blade after 50 hours mowing or 2 years
whichever is the sooner - regardless of
condition. If the blade is cracked or damaged
replace it with a new one.
ENGLISH - 4

Advertisement

loading

This manual is also suitable for:

R 43sR 43seRoyal 43Royal 43sRoyal 43se