1000 lb. hydraulic motorcycle service lift (17 pages)
Summary of Contents for Central Hydraulics 98178
Page 1
Air over HydrAulic ATv/MoTorcycle lifT Model 98178 SeT up And operATing inSTrucTionS ® distributed exclusively by Harbor freight Tools 3491 Mission Oaks Blvd., Camarillo, CA 93011 visit our website at: http://www.harborfreight.com read this material before using this product. failure to do so can result in serious injury.
Store the tool when it is idle out of Always wear hearing reach of children and other un- protection when using trained persons. A tool is dangerous the tool. Prolonged expo- in the hands of untrained users. SKU 98178 for technical questions, please call 1-800-444-3353. Page 3...
WARNING marking concerning Risk range as marked on the tool. Always of Explosion. verify prior to using the tool that the air source has been adjusted to the SKU 98178 for technical questions, please call 1-800-444-3353. Page 4...
Do not leave any load on the Lift for an extended period of time. This Lift is not designed as a storage device. Remove motorcycle or ATV from Lift immediately after completing service operation. REV 09a SKU 98178 for technical questions, please call 1-800-444-3353. Page 5...
This air tool may be shipped with a protective plug covering the air inlet. Remove this plug before set up. REV 09a SKU 98178 for technical questions, please call 1-800-444-3353. Page 6...
PSI) at any time. Adjust the pres- Brace Frame (12) using Ram Pin sure gradually, while checking the air (15). Secure the Ram Pin (15) with the Locking Pin (14). Next attach the SKU 98178 for technical questions, please call 1-800-444-3353. Page 7...
Release Pedal (19) slowly. If the lift operates properly you have completed this process. If the Lift does raise or lower smoothly and controllably, repeat the purging pro- cess. rev 08j SKU 98178 for technical questions, please call 1-800-444-3353. Page 8...
Page 9
Safety Lock Bar (11) Control Valve (24) with Handle in Open Position Safety Lock Bar (11) Lock Support (2) in Unlocked Position Lock Support (2) in Locked Position Foot Pedal (18) SKU 98178 for technical questions, please call 1-800-444-3353. Page 9...
Disengage the Safety Bar (11) from Press the Release Pedal (19) to fully the side rail of the Frame Base. lower the lift. REV 09a SKU 98178 for technical questions, please call 1-800-444-3353. Page 10...
Page 11
Roll the lift away from the item. To prevent accidents, detach the air supply. Clean external surfaces of the lift with clean, dry cloth. Then store the tool indoors out of children’s reach. REV 09a SKU 98178 for technical questions, please call 1-800-444-3353. Page 11...
(24) or housing. Dirty, worn or damaged Clean or replace valve assembly. valve. follow all safety precautions whenever diagnosing or servicing the tool. disconnect air supply before service. SKU 98178 for technical questions, please call 1-800-444-3353. Page 13...
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 98178 for technical questions, please call 1-800-444-3353. Page 15...
Page 16
All parts for the Air Ram and Pump Assembly have an “a” suffix, such as “19a”. Do not confuse these part numbers with the part numbers for the Lift Tool which are listed on page 14, and have no suffix. SKU 98178 for technical questions, please call 1-800-444-3353. Page 16...
If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts. SKU 98178 for technical questions, please call 1-800-444-3353. Page 17...