Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Planar EL320.240.36-HB
Summary of Contents for Planar EL320.240.36-HB
- Page 1 EL320.240.36-HB High-Bright Small Graphics Display USER’S MANUAL www.planar.com...
- Page 2 Revision Control Date Description September 2001 Document number OM220-01 June 2004 Document number 020-0346-00A...
-
Page 3: Table Of Contents
Contents EL320.240.36-HB Quarter-VGA Display......................2 Features and Benefits ............................2 Installation and Handling............................3 Mounting EL Displays ............................3 Cable Length................................4 Cleaning ...................................4 Avoiding Burn-In ..............................4 Specifications ................................5 Control Basics .................................5 Power..................................5 Connector ................................6 Dimming Connector J2..........................Interface Information............................7 Video Input Signals............................Internal Frame Buffer............................9 Dimming ..................................9... -
Page 4: El320.240.36-Hb Quarter-Vga Display
EL320.240.36-HB Quarter-VGA Display The EL320.240.36-HB thin film electroluminescent (EL) display is a high- performance alternative to quarter-VGA LCDs and is the ideal solution in demanding applications where superior visual performance and environmental ruggedness are critical. The EL320.240.36-HB utilizes Planar’s proprietary Integral Contrast Enhancement (ICE™) technology to achieve unparalleled image quality without the use of expensive filters. -
Page 5: Installation And Handling
The EL320.240.36-HB mounting tabs were designed for a 3 mm screw. Mounting surfaces should be flat to within ±0.6 mm (±0.025"). Use all the mounting holes provided. -
Page 6: Cable Length
Excessive cable lengths can pick up unwanted EMI. There are third party products which allow this maximum cable length to be exceeded. Contact Planar Application Engineering for more information. Cleaning As with any glass or coated surface, care should be taken to minimize scratching. -
Page 7: Specifications
There is no overcurrent protection on either the V or V inputs to protect against catastrophic faults. Planar recommends the use of a series fuse on the 12 volt supply(V ). A general guideline is to rate the fuse at 1.8 to 2 times the display maximum current rating. -
Page 8: Connector
Scan rate control +5 V Power Ground Vertical Sync Ground Horizontal Sync Ground VCLK Video Clock Ground Video Data Ground Video Data Ground Video Data Ground Video Data Ground Connect pin 3 to ground for normal display operation. EL320.240.36-HB Operations Manual (020-0346-00A) -
Page 9: Dimming Connector J2
LUMD Luminance D Interface Information Planar EL Small Graphics Displays (SGD) incorporate an interface that is similar to many LCD interfaces. This interface is supported by a variety of off-the-shelf chip sets which take care of all display control functionality, freeing the system processor for other tasks. -
Page 10: Figure 3. Pixel Location Versus Sequence Of Data
Row 1 EL Panel (Front) VID3 VID2 VID1 VID0 Figure 3. Pixel Location versus Sequence of Data. EL320.240.36-HB Operations Manual (020-0346-00A) -
Page 11: Internal Frame Buffer
VS signal. Dimming There are two standard methods for dimming the EL320.240.36-HB display. Analog dimming using the J2 dimming connector described on page 7 of this manual allows for manual dimming from 100% to approximately 5% of the full brightness. -
Page 12: Optical
Operating/non-operating 100 g, 6 ms, half sine wave per IEC 68-2-27, test Ea. * Temperature sensor is built in to provide power cut-off in case of over heating. Note: Power cut-off is not operative in Selftest. EL320.240.36-HB Operations Manual (020-0346-00A) -
Page 13: Reliability
Planar reserves the right to relocate components within constraints of the component envelope without prior customer notification. For this reason, Planar advises users to design enclosure components to be outside the component envelope. Device designers will need to consider their specific system requirements to determine the spacing necessary to maintain the specified ambient temperature. -
Page 14: Figure 4. Display Dimensions
To front of glass Top View Dimensions in are millimeters; inches in brackets. Tolerances unless specified ± 0.50 [0.02] ± 0.25 [0.01] Figure 4. Display Dimensions. Note: Please refer to www.planar.com/support to view the mechanical outline drawing. EL320.240.36-HB Operations Manual (020-0346-00A) -
Page 15: Description Of Warranty
-40 to +85°C operating temperature Design and specifications are subject to change without notice. Planar Systems continues to provide optional, and in many cases custom, features to address the specific customer requirements. Consult Planar Sales for pricing, lead time and minimum quantity requirements. -
Page 16: Support And Service
Support and Service Planar is a U.S. company based in Beaverton, Oregon and Espoo, Finland, with a world-wide sales distribution network. Full application engineering support and service are available to make the integration of Planar displays as simple and quick as possible for our customers. - Page 17 Tel: +358-9-420-01 Hours: M-F, 7:00am - 4pm CET © 2004 Planar Systems, Inc. 06/04 Planar is a registered trademark of Planar Systems, Inc. ICE, ICEBrite, and ICEPlus are trademarks of Planar Systems, Inc. Other brands and names are the property of their respective owners.