Page of 16

Husky HDN10500 Operating Instructions Manual

Husky pin nailer operating instructions.
See Warranty on page 8 for important information about commercial use of this product.
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
Table of Contents
Description . . . . . . . . . . . . . . . . . . . . . 1
Unpacking . . . . . . . . . . . . . . . . . . . . . . 1
Safety Guidelines . . . . . . . . . . . . . . . . 1
Important Safety Information . . . . . . 1
Tool Components and
Specifications. . . . . . . . . . . . . . . . . . . . 2
Operating Instructions . . . . . . . . . . . . 4
Lubrication . . . . . . . . . . . . . . . . . . . . 4
Recommended Hookup. . . . . . . . . . 4
Operational Mode . . . . . . . . . . . . . . 5
Trigger Only Mode. . . . . . . . . . . . . . 5
Interchange Information . . . . . . . . . . 5
Troubleshooting Chart . . . . . . . . . . . . 7
Warranty . . . . . . . . . . . . . . . . . . . . . . . 8
Description
This nailer is designed for tacking
decorative trim, glazing strips, small
picture frames and cabinetry trim.
Features include: narrow nose for
fitting in tight spaces and trigger lock.
Unpacking
After unpacking the unit, inspect
carefully for any damage that may
have occurred during transit. Make sure
to tighten fittings, bolts, etc., before
putting unit into service.
Husky Tools meet or exceed Industries' Standards as set forth by the American National Standard Institute/
International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002.
© 2008
Safety Guidelines
This manual contains information
that is very important to know and
understand. This information is
provided for SAFETY and to PREVENT
EQUIPMENT PROBLEMS. To help
recognize this information, observe the
following symbols.
hazardous situation which, if not
avoided, WILL result in death or serious
injury.
hazardous situation which, if not
avoided, COULD result in death or
serious injury.
hazardous situation which, if not
avoided, MAY result in minor or
moderate injury.
information, that if not followed, may
cause damage to equipment.
NOTE: Information that requires special
attention.
Important Safety Instructions
INSTRUCTIONS PERTAINING TO A
RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS
should always be followed, including
the following:
REMINDER: Keep your dated proof of purchase for warranty purposes!
Attach it to this manual or file it for safekeeping.
1 inch 23g Micro
Pin Nailer
Danger indicates
an imminently
Warning indicates
a potentially
Caution indicates
a potentially
Notice indicates
important
CALIFORNIA PROPOSITION 65
contain chemicals known to the State
of California to cause cancer and birth
defects or other reproductive harm.
Wash hands after handling.
You can create dust when
When using tools,
you cut, sand, drill or grind
basic precautions
materials such as wood,
paint, metal, concrete, cement, or other
masonry. This dust often contains
chemicals known to cause cancer, birth
defects, or other reproductive harm.
Wear protective gear.
HDN10500
Model HDN10500
Locate model and date code on
tool and record below:
Model No.: _____________________
Date Code: _____________________
Retain these numbers for
future reference.
This product or
its power cord may
IN726900AV 6/08

   Related Manuals for Husky HDN10500

   Summary of Contents for Husky HDN10500

  • Page 1

    REMINDER: Keep your dated proof of purchase for warranty purposes! Husky Tools meet or exceed Industries’ Standards as set forth by the American National Standard Institute/ International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002. © 2008...

  • Page 2: Specifications

    Be thoroughly familiar with the controls and the proper use of the equipment. Follow all instructions. Contact your Husky representative if you have any questions. c. Only persons well acquainted with these rules of safe operation should be allowed to use the unit.

  • Page 3

    Do not use a check valve or any other fi tting which allows air to remain in the tool. Death or serious personal injury could occur. HDN10500 Never place hands or any other body parts in the fastener discharge area of the tool.

  • Page 4: Operating Instructions, Lubrication, Recommended Hookup

    Do not make any modifi cations to the tool without fi rst obtaining written approval from Husky. Do not use the tool if any shields or guards are removed or altered. Do not use the tool as a hammer. Personal injury or tool damage may occur.

  • Page 5: Operational Mode, Trigger Only Mode, Loading/unloading The Tool, Clearing A Jam From The Tool

    Remove and replace driver assembly using your fingers. Replace components and head cap as removed. TOOL REPAIR Only qualified personnel should repair the tool and they should use genuine Husky replacement parts and accessories, or parts and accessories which perform equivalently.

  • Page 6: Interchange Information

    Operating Instructions Operating Instructions USER-MAINTENANCE INSTRUCTIONS (Continued) ASSEMBLY PROCEDURE FOR SEALS When repairing a tool, the internal parts must be cleaned and lubricated. Parker O-lube or equivalent must be used on all o-rings. Each o-ring must be coated with O-lube before assembling. A small amount of oil must be used on all moving surfaces and pivots.

  • Page 7: Troubleshooting Chart

    2. Fasteners are not correct size 3. Fasteners are bent 4. Magazine or nose screws are loose 5. Driver is damaged pusher from moving freely in magazine lubrication HDN10500 Corrective Action Replace o-rings 1. Replace o-rings 2. Replace bumper 1. Tighten screws 2.

  • Page 8: Warranty

    Operating Instructions Limited Warranty - Husky 1 inch 23g Micro Pin Nailer by Campbell Hausfeld 1. DURATION: From the date of purchase by the original purchaser as follows: One (1) Year. 2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison, Ohio, 45030, Telephone: (800) 543-6400 3.

  • Page 9

    RECORDATORIO: ¡Guarde su comprobante de compra con fecha para fines de la garantía! Adjúntela a este manual o archívela en lugar seguro. Las herramientas Husky cumplen o exceden los estándares de la Industria establecidos por el American National Standard Institute/International Staple, Nail and Tool Association, en los códigos ANSI/ISANTA SNT-101-2002.

  • Page 10

    Familiarísece con los controles y el uso adecuado del equipo.Siga todas las instrucciones. Póngase en contacto con su representante Husky si tiene alguna pregunta. c. Sólo se les debe permitir usar esta unidad a aquellas personas bien familiarizadas con estas reglas de manejo seguro.

  • Page 11

    Cuando no use la herramienta, coloque también la traba del gatillo en la posición de seguro. 11-Sp HDN10500 Desconecte siempre la herramienta de la fuente de energía cuando no la esté atendiendo, cuando le esté realizando mantenimiento o reparaciones, desobstruyéndola o...

  • Page 12

    No haga ninguna modifi cación a la herramienta sin obtener primero la aprobación por escrito de Husky. No use Conexión Recomendada Conector rápido la herramienta si le faltan alguna de las tapas protec-toras o si éstas han sido modifi...

  • Page 13

    Botón del seguro 13-Sp HDN10500 3. Introduzca una tira de sujetadores en el cargador con las puntillas colocadas como se indica. Cerciórese de que las puntillas no estén sucias ni dañadas. Las puntillas llevan una marca con la dirección para cargar.

  • Page 14

    MANTENIMIENTO ASSISTÊNCIA TÉCNICA Para mayor información en relación al funcionamiento o reparación de este producto, comuníquese con el concesionario de Husky más cercano a su domicilio. SUJETADORES Y REPUESTOS Use sólo puntillas micro, calibre 23. El desempeño de las herramientas, la seguridad y la duración pueden...

  • Page 15

    15-Sp HDN10500 Solución Debe reemplazar los anillos en O 1. Debe reemplazar los anillos en O. 2. Debe reemplazar la defensa. 1. Debe apretar los tornillos. 2. Reemplace el sello 1.

  • Page 16

    Manual de Instrucciones de Operación Garantía Limitada - Clavadora de Micro Puntillas de 1 pulg. calibre 23 de Campbell Hausfeld 1 DURACION: A partir de la fecha de compra por el comprador original tal como se especifica a continuación: Un (1) año. 2.

Comments to this Manuals

Symbols: 0
Latest comments:
  • Bob Sep 14, 2014 12:41:
    My gun doesn't stopped working after shooting 2 nails. No hissing, no nothing? Air supply is 110 PSi
    It is the H250SF finish nailer.
    It has been rarely used.
    Any suggestion​s