Table of Contents
Advertisement
EMPIRE
EMPIRE
Comfort Systems
Select Vent-Free Universal Fireboxes
ANSI Z21.91 Ventless Fireplace Enclosures for Gas Fired
Decorative Type Unvented Room Heaters
wARNING: If the information in these instructions are not
followed exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.
— Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
— wHAT TO DO IF yOU SMELL GAS
•
Do not try to light any appliance.
•
Do not touch any electrical switch; do not use any
phone in your building.
•
Immediately call your gas supplier from a neigh-
bor's phone. Follow the gas supplier's instruc-
tions.
•
If you cannot reach your gas supplier, call the fire
department.
— Installation and service must be performed by a quali-
fied installer, service agency or the gas supplier.
DO NOT ATTEMpT TO MODIFy OR ALTER THE cONSTRUc-
TION OF THE FIREBOX OR ITS cOMpONENTS. ANy MODI-
FIcATION OR ALTERATION OF cONSTRUcTION MAy VOID
THE wARRANTy OF THIS FIREBOX.
cHILDREN AND ADULTS SHOULD BE ALERTED TO THE
HAZARDS OF HIGH SURFAcE TEMpERATURE AND
SHOULD STAy AwAy TO AVOID BURNS OR cLOTHING IG-
NITION.
yOUNG cHILDREN SHOULD BE cAREFULLy SUpERVISED
wHEN THEy ARE IN THE SAME ROOM AS THE FIREBOX.
INSTALLATION INSTRUcTIONS
AND OwNER'S MANUAL
GAS-FIRED
Installer:
consumer: Retain this manual for future reference.
wARNING:
tion, service or maintenance can cause injury or property
damage. Refer to this manual. For assistance or additional
information, consult a qualified installer, service agency or
the gas supplier.
carefully review the instructions supplied with the decora-
tive type unvented room heater for the minimum fireplace
size requirement.
DO NOT INSTALL A VENT-FREE LOG SET IN THIS FIREBOX,
UNLESS THIS FIREBOX MEETS THE MINIMUM DIMENSIONS
REQUIRED FOR THE INSTALLATION.
UNIVERSAL FIREBOX FOR
ALL VENT-FREE LOG SETS
MODELS
VFS(32,36,42)FB0F-5
VFS(36,42)FB2HF-5
Leave this manual with the appliance.
FOR USE ONLy wITH A LISTED GAS-FIRED
UNVENTED DEcORATIVE ROOM HEATER NOT TO EX-
cEED 40,000 BTU/H.
DO NOT BUILD A wOOD FIRE.
Improper installation, adjustment, altera-
Page 1
Advertisement
Table of Contents
Related Manuals for Empire Comfort Systems VFS32FB0F-5
Summary of Contents for Empire Comfort Systems VFS32FB0F-5
-
Page 1: Installation Instructions
INSTALLATION INSTRUCTIONS EMPIRE EMPIRE AND OWNER'S MANUAL Comfort Systems UNIVERSAL FIREBOX FOR ALL VENT-FREE LOG SETS Select Vent-Free Universal Fireboxes MODELS VFS(32,36,42)FB0F-5 VFS(36,42)FB2HF-5 GAS-FIRED ANSI Z21.91 Ventless Fireplace Enclosures for Gas Fired Decorative Type Unvented Room Heaters WARNING: If the information in these instructions are not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. -
Page 1: Installation Instructions
INSTALLATION INSTRUcTIONS EMPIRE EMPIRE AND OwNER'S MANUAL Comfort Systems UNIVERSAL FIREBOX FOR ALL VENT-FREE LOG SETS Select Vent-Free Universal Fireboxes MODELS VFS(32,36,42)FB0F-5 VFS(36,42)FB2HF-5 GAS-FIRED ANSI Z21.91 Ventless Fireplace Enclosures for Gas Fired Decorative Type Unvented Room Heaters wARNING: If the information in these instructions are not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. -
Page 2: Table Of Contents
TABLE OF CONTENTS SECTION PAGE IMPORTANT SAFETY INFORMATION ................3 INTRODUCTION ......................3 CLEARANCES ......................4 - 5 FIREBOX INSTALLATION INSTRUCTIONS ............... 6 - 8 INSTALLING HOOD..................... 8 - 9 GAS LINE CONNECTION ....................9 OPTIONAL FRESH AIR KIT INSTALLATION INSTRUCTIONS ......10 - 12 OPTIONAL FBB5 SINGLE SPEED BLOWER INSTALLATION INSTRUCTIONS ... -
Page 2: Table Of Contents
TABLE OF cONTENTS SEcTION pAGE IMPORTANT SAFETY INFORMATION ................3 INTRODUCTION ......................3 CLEARANCES ......................4 - 5 FIREBOX INSTALLATION INSTRUCTIONS ............... 6 - 8 INSTALLING HOOD..................... 8 - 9 GAS LINE CONNECTION ....................9 OPTIONAL FRESH AIR KIT INSTALLATION INSTRUCTIONS ......10 - 12 OPTIONAL FBB5 SINGLE SPEED BLOWER INSTALLATION INSTRUCTIONS ... -
Page 3: Important Safety Information
It is imperative that control compartment, burners and circulating air passageways of the appliance be kept clean. This Empire Comfort Systems, Inc. firebox and its - Installation and/or use of any component part components have been tested and will operate safely... -
Page 3: Important Safety Information
It is imperative that control compartment, burners and circulating air passageways of the appliance be kept clean. This Empire Comfort Systems, Inc. firebox and its - Installation and/or use of any component part components have been tested and will operate safely... -
Page 4: Clearances
CLEARANCES Sidewall Clearances: The clearance from the inside of the firebox to perpendicular combustible side wall should not be less than 6 inches. See Figure 1. Firebox Side and Back Clearances: The firebox outer casing side and back flanges are zero clearance to combustibles. Top Framing and Finishing: Combustible finishing materials requires 3/8 inch to top of unit. There are two shoulder bolts attached to the unit to maintain the minimum clearance. See Figures 2 and 3. -
Page 4: Clearances
cLEARANcES Sidewall clearances: The clearance from the inside of the firebox to perpendicular combustible side wall should not be less than 6 inches. See Figure 1. Firebox Side and Back Clearances: The firebox outer casing side and back flanges are zero clearance to combustibles. Top Framing and Finishing: Combustible finishing materials requires 3/4 inch to top of unit. There are two shoulder bolts attached to the unit to maintain the minimum clearance. See Figures 2 and 3. - Page 5 CLEARANCES Ceiling Clearances: The ceiling height should not be less than 84 inches from the bottom of the firebox. See Figure 4. Mantel Clearances: Vent free firebox models must use the hood supplied with the firebox, or one of the optional hood kits available for each model. If a combustible mantel is installed, it must meet the clearance requirements detailed below. Leave at least 36 inches clearance from the front of the firebox. Figure 4 - Clearances to Combustibles 33743-0-0314 Page 5...
- Page 5 cLEARANcES ceiling clearances: The ceiling height should not be less than 84 inches from the bottom of the firebox. See Figure 4. Mantel clearances: Vent free firebox models must use the hood supplied with the firebox, or one of the optional hood kits available for each model. If a combustible mantel is installed, it must meet the clearance requirements detailed below. Leave at least 36 inches clearance from the front of the firebox. Figure 4 - Clearances to Combustibles 33743-2-0315 Page 5...
-
Page 6: Firebox Installation Instructions
FIREBOX INSTALLATION INSTRUCTIONS Any vent-free Gas Log Heater must be “For use with approved ANSI At this point, you should have decided what components to include Z21.11.2 unvented room heater.” in your installation, and where the firebox is to be located. If this has not been done, stop and consult your dealer for assistance Follow and complete the installation instructions of the gas log set with this planning. and the requirements of this firebox. Planning Your Installation Check all fittings for leaks before lighting the gas log set. Please note that the optional VFA2 Fresh Air kit available for use In planning the installation for the firebox, it is necessary to determine with the Vent Free Firebox must be installed at the time of the initial where the unit is to be installed and whether optional accessories installation. Refer to pages 10, 11 and 12 for detailed instructions are desired. Gas supply piping should also be planned at this time. for the air kit. Accessory kits such as the FBB5 Blower kit, Trim kits, Mantels, Full A gas shut off must be in this line. Cabinet Mantels, plus other Decorative Frame, Hood, and Door The firebox can be mounted on any of these surfaces: accessory kits may be installed after the firebox is secured to the... -
Page 6: Firebox Installation Instructions
FIREBOX INSTALLATION INSTRUcTIONS Any vent-free Gas Log Heater must be “For use with approved ANSI At this point, you should have decided what components to include Z21.11.2 unvented room heater.” in your installation, and where the firebox is to be located. If this has not been done, stop and consult your dealer for assistance Follow and complete the installation instructions of the gas log set with this planning. and the requirements of this firebox. planning your Installation Check all fittings for leaks before lighting the gas log set. Please note that the optional VFA2 Fresh Air kit available for use In planning the installation for the firebox, it is necessary to determine with the Vent Free Firebox must be installed at the time of the initial where the unit is to be installed and whether optional accessories installation. Refer to pages 10, 11 and 12 for detailed instructions are desired. Gas supply piping should also be planned at this time. for the air kit. Accessory kits such as the FBB5 Blower kit, Trim kits, Mantels, Full A gas shut off must be in this line. Cabinet Mantels, plus other Decorative Frame, Hood, and Door The firebox can be mounted on any of these surfaces: accessory kits may be installed after the firebox is secured to the... - Page 7 FIREBOX INSTALLATION INSTRUCTIONS OUTER FIREBOX DIMENSIONS INNER FIREBOX DIMENSIONS SIDE VIEW TOP VIEW OUTER FIERBOX DIMENSIONS INNER FIERBOX DIMENSIONS (in inches) (in inches) FLUSH WITHOUT BRICK INDEX INDEX VFS32 VFS36 VFS42 VFS32 VFS36 VFS42 LETTER LETTER 38-1/16 38-1/16 38-1/16 34-1/4 39-1/4 43-1/4 23-1/2...
- Page 7 FIREBOX INSTALLATION INSTRUcTIONS OUTER FIREBOX DIMENSIONS INNER FIREBOX DIMENSIONS SIDE VIEW TOP VIEW OUTER FIERBOX DIMENSIONS INNER FIERBOX DIMENSIONS (in inches) (in inches) FLUSH wITHOUT BRIcK INDEX INDEX VFS32 VFS36 VFS42 VFS32 VFS36 VFS42 LETTER LETTER 38-1/16 38-1/16 38-1/16 34-1/4 39-1/4 43-1/4 23-1/2...
-
Page 8: Installing Hood
FIREBOX INSTALLATION INSTRUCTIONS Locating Firebox Place firebox in framing opening. Use the tabs on the side of the firebox to attach firebox to framing. Different tab locations can be used for finishing materials with thicknesses of 1/2 inch and 5/8 inch. See Figure 8. Framing tabs should fit directly against framing material. Use at least one nail per bracket to secure in place. Check squareness of the firebox prior to securing to framed opening. See Figure 9. Figure 9 Figure 8 INSTALLING HOOD A black hood that is furnished with each firebox (or optional hood) Flush Face Models MUST be installed before the firebox is used. Failure to do so may create a possible fire hazard. The hood is located behind upper louver, or inside the firebox on flush face units. If brass, stainless steel, or hammered pewter hoods are desired, they can... -
Page 8: Installing Hood
FIREBOX INSTALLATION INSTRUcTIONS Locating Firebox Place firebox in framing opening. Use the tabs on the side of the firebox to attach firebox to framing. Different tab locations can be used for finishing materials with thicknesses of 1/2 inch and 5/8 inch. See Figure 8. Framing tabs should fit directly against framing material. Use at least one nail per bracket to secure in place. Check squareness of the firebox prior to securing to framed opening. See Figure 9. Figure 9 Figure 8 INSTALLING HOOD A black hood that is furnished with each firebox (or optional hood) Flush Face Models MUST be installed before the firebox is used. Failure to do so may create a possible fire hazard. The hood is located behind upper louver, or inside the firebox on flush face units. If brass, stainless steel, or hammered pewter hoods are desired, they can... -
Page 9: Gas Line Connection
INSTALLING HOOD Extended Hoods If your non-combustible facing material is over 1" in thickness that will be used to finish this firebox, an extended hood is available that will extend out 2" farther out into the room. Contact your local dealer for details. VB4H32BL Standard Black VB4H36BL Standard Black VB4H42BL Standard Black VB4H32BR Polished Brass VB4H36BR Polished Brass VB4H42BR Polished Brass VB4H32SS Stainless Steel VB4H36SS Stainless Steel VB4H42SS Stainless Steel VB4H32HP Hammered Pewter VB4H36HP Hammered Pewter VB4H42HP Hammered Pewter Finishing All joints (top, bottom and sides), where the wall or decorative facing material meets the firebox surround should be sealed with a non- combustible material. Hearth extensions are recommended, but not required for these fireboxes. GAS LINE CONNECTION The firebox is designed to accept a 3/8-inch gas line for an approved vent-free gas logset. Have the line installed by a qualified service person in accordance with all building codes. Consult local building... -
Page 9: Gas Line Connection
INSTALLING HOOD Extended Hoods If your non-combustible facing material is over 1" in thickness that will be used to finish this firebox, an extended hood is available that will extend out 2" farther out into the room. Contact your local dealer for details. VB4H32BL Standard Black VB4H36BL Standard Black VB4H42BL Standard Black VB4H32BR Polished Brass VB4H36BR Polished Brass VB4H42BR Polished Brass VB4H32SS Stainless Steel VB4H36SS Stainless Steel VB4H42SS Stainless Steel VB4H32HP Hammered Pewter VB4H36HP Hammered Pewter VB4H42HP Hammered Pewter Finishing All joints (top, bottom and sides), where the wall or decorative facing material meets the firebox surround should be sealed with a non- combustible material. Hearth extensions are recommended, but not required for these fireboxes. GAS LINE cONNEcTION The firebox is designed to accept a 3/8-inch gas line for an approved vent-free gas logset. Have the line installed by a qualified service person in accordance with all building codes. Consult local building... -
Page 10: Optional Fresh Air Kit Installation Instructions
OPTIONAL FRESH AIR KIT INSTALLATION INSTRUCTIONS The optional Fresh Air Kit is designed to introduce outside air to the firebox as desired. It must be installed prior to, or at the time of firebox installation to framing. The Fresh Air kit must be installed prior to the installation of wall- board or other finishing materials around the unit. Hardware needed (not provided): 4 inch Aluminum Flex Duct, 2 Band Clamps Tools needed: Gloves, Metal snips, 5/16 inch Nut Driver, Phillips Screwdriver Caution: Sharp edges Slide Assembly Installation 1. Begin by removing the rectangular cutout located on the left side of the unit. Use gloves and sheet metal snips to create Figure 15 the opening for the Air Door assembly to install into. See Fig- ure 13. Figure 13 Figure 16 2. Bend the tab out of the way. -
Page 10: Optional Fresh Air Kit Installation Instructions
OpTIONAL FRESH AIR KIT INSTALLATION INSTRUcTIONS The optional Fresh Air Kit is designed to introduce outside air to the firebox as desired. It must be installed prior to, or at the time of firebox installation to framing. The Fresh Air kit must be installed prior to the installation of wall- board or other finishing materials around the unit. Hardware needed (not provided): 4 inch Aluminum Flex Duct, 2 Band Clamps Tools needed: Gloves, Metal snips, 5/16 inch Nut Driver, Phillips Screwdriver caution: Sharp edges Slide Assembly Installation 1. Begin by removing the rectangular cutout located on the left side of the unit. Use gloves and sheet metal snips to create Figure 15 the opening for the Air Door assembly to install into. See Fig- ure 13. Figure 13 Figure 16 2. Bend the tab out of the way. - Page 11 OPTIONAL FRESH AIR KIT INSTALLATION INSTRUCTIONS 5. Push the handle for Open position and pull the handle for the Completion of Air Kit installation Closed position. See Figure 17. 1. Determine the length of 4 inch diameter rigid or flex duct con- nector (installer supplied) you will need from the firebox/fire- place to the exterior surface of the outside wall, where the air kit hood will be installed. Add a few extra inches to the length to allow for easier attachment of the outside duct connection prior to securing the outside rain cap hood to the building. 2. Secure the 4 inch diameter duct to the Slide Assembly collar on the firebox with band clamps or screws (installer supplied). 3. Run the other end of the duct through the exterior wall cutout. 4. From the outside of the building, connect the duct to the collar on the outside air vent assembly with band clamp or screws to secure (installer supplied). 5. Secure the Outside Air Vent Assembly to the outside wall with the four 10 x 1 1/2 Hex Head Slotted Screws provided. Seal with caulk as necessary. See Figure 18. Figure 19 illustrates the various options for installation of the air duct run possibilities.
- Page 11 OpTIONAL FRESH AIR KIT INSTALLATION INSTRUcTIONS 5. Push the handle for Open position and pull the handle for the completion of Air Kit installation Closed position. See Figure 17. 1. Determine the length of 4 inch diameter rigid or flex duct con- nector (installer supplied) you will need from the firebox/fire- place to the exterior surface of the outside wall, where the air kit hood will be installed. Add a few extra inches to the length to allow for easier attachment of the outside duct connection prior to securing the outside rain cap hood to the building. 2. Secure the 4 inch diameter duct to the Slide Assembly collar on the firebox with band clamps or screws (installer supplied). 3. Run the other end of the duct through the exterior wall cutout. 4. From the outside of the building, connect the duct to the collar on the outside air vent assembly with band clamp or screws to secure (installer supplied). 5. Secure the Outside Air Vent Assembly to the outside wall with the four 10 x 1 1/2 Hex Head Slotted Screws provided. Seal with caulk as necessary. See Figure 18. Figure 19 illustrates the various options for installation of the air duct run possibilities.
-
Page 12: Optional Fresh Air Kit Installation Instructions
OPTIONAL FRESH AIR KIT INSTALLATION INSTRUCTIONS PARTS LIST INDEX NO. PART NO. DESCRIPTION 29259 Outside Air Vent Assembly 29257 Slide Assembly 29263 Handle Retainer Hardware Pack Page 12 33743-0-0314... -
Page 12: Optional Fresh Air Kit Installation Instructions
OpTIONAL FRESH AIR KIT INSTALLATION INSTRUcTIONS pARTS LIST INDEX NO. pART NO. DEScRIpTION 29259 Outside Air Vent Assembly 29257 Slide Assembly 29263 Handle Retainer Hardware Pack Page 12 33743-2-0315... -
Page 13: Optional Fbb5 Single Speed Blower Installation Instructions
OPTIONAL FBB5 SINGLE SPEED BLOWER INSTALLATION INSTRUCTIONS Attention: It is recommended to install the blower assembly be- A factory installed junction box is located on the lower right fore connecting gas inlet supply line. side of the fireplace. Wiring must be fed to the junction box Wiring and attached to the receptacle that is provided. From right The appliance, when installed, must be electrically grounded in side of the fireplace, remove the screw securing the junction accordance with local codes or, in the absence of local codes, box assembly. Leave approximately 6” of wire in the junction... -
Page 13: Optional Fbb5 Single Speed Blower Installation Instructions
OpTIONAL FBB5 SINGLE SpEED BLOwER INSTALLATION INSTRUcTIONS Attention: It is recommended to install the blower assembly be- A factory installed junction box is located on the lower right fore connecting gas inlet supply line. side of the fireplace. Wiring must be fed to the junction box wiring and attached to the receptacle that is provided. From right The appliance, when installed, must be electrically grounded in side of the fireplace, remove the screw securing the junction accordance with local codes or, in the absence of local codes, box assembly. Leave approximately 6” of wire in the junction... - Page 14 OPTIONAL FBB5 SINGLE SPEED BLOWER INSTALLATION INSTRUCTIONS 2. Remove air deflector by removing the four screws securing it 6. The fan control wires will slide down between the firebox and to the blower assembly. outer wrap near the blower assembly. See Figure 25. 7. One fan control wire will have a 1/4” female terminal that must be attached to the open terminal on the blower motor. See Figure 28, Connection A. 6. The other fan control wire has a 1/4” male terminal. Attach this terminal to the open terminal on the blower power cord. See Figure 28, Connection B. 9. Route the wires away from moving parts of the blower assem- bly and retain wires together near the blower motor using the plastic purse clip provided.
- Page 14 OpTIONAL FBB5 SINGLE SpEED BLOwER INSTALLATION INSTRUcTIONS 2. Remove air deflector by removing the four screws securing it 6. The fan control wires will slide down between the firebox and to the blower assembly. outer wrap near the blower assembly. See Figure 25. 7. One fan control wire will have a 1/4” female terminal that must be attached to the open terminal on the blower motor. See Figure 28, connection A. 6. The other fan control wire has a 1/4” male terminal. Attach this terminal to the open terminal on the blower power cord. See Figure 28, connection B. 9. Route the wires away from moving parts of the blower assem- bly and retain wires together near the blower motor using the plastic purse clip provided.
-
Page 15: Optional Fbb5 Single Speed Blower Installation Instructions
OPTIONAL FBB5 SINGLE SPEED BLOWER INSTALLATION INSTRUCTIONS Blower Motor The blower motor does not have oiling holes. Do not attempt to oil the blower motor. Blower Wheels The blower wheels will collect lint and could require periodic clean- ing. If the air output decreases or the noise level increases, it indi- cates a dirty blower wheel. Remove fan and clean blower wheels. Warning: Unplugging of blower accessory will not stop the heat- er from cycling. To turn off gas to the heater (millivolt model): push in gas control knob slightly and turn clockwise to “OFF.” Do not force. To turn off gas on direct ignition model, turn gas line valve to “OFF.” Figure 27 INDEX NO. PART NO. DESCRIPTION R7731 BLOWER ASSEMBLY... -
Page 15: Optional Fbb5 Single Speed Blower Installation Instructions
OpTIONAL FBB5 SINGLE SpEED BLOwER INSTALLATION INSTRUcTIONS Blower Motor The blower motor does not have oiling holes. Do not attempt to oil the blower motor. Blower wheels The blower wheels will collect lint and could require periodic clean- ing. If the air output decreases or the noise level increases, it indi- cates a dirty blower wheel. Remove fan and clean blower wheels. warning: Unplugging of blower accessory will not stop the heat- er from cycling. To turn off gas to the heater (millivolt model): push in gas control knob slightly and turn clockwise to “OFF.” Do not force. To turn off gas on direct ignition model, turn gas line valve to “OFF.” Figure 27 INDEX NO. pART NO. DEScRIpTION R7731 BLOWER ASSEMBLY... -
Page 16: Junction Box Wiring Installation Instructions
JUNCTION BOX WIRING INSTALLATION INSTRUCTIONS CAUTION: ALL WIRING SHOULD BE DONE BY A QUALIFIED ELECTRICIAN AND SHALL BE IN COMPLIANCE WITH ALL LOCAL, CITY AND STATE BUILDING CODES. BEFORE MAKING THE ELECTRICAL CONNECTION, MAKE SURE THAT MAIN POWER SUPPLY IS DISCONNECTED. THE APPLIANCE, WHEN INSTALLED, MUST BE ELECTRICALLY GROUNDED IN ACCORDANCE WITH LOCAL CODES OR, IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL ELECTRICAL CODE ANSI/NFPA 70 (LATEST EDITION) A factory installed junction box is located on the lower right hand side of the firebox. Wiring must be fed to the junction box and... -
Page 16: Junction Box Wiring Installation Instructions
JUNcTION BOX wIRING INSTALLATION INSTRUcTIONS cAUTION: ALL wIRING SHOULD BE DONE By A QUALIFIED ELEcTRIcIAN AND SHALL BE IN cOMpLIANcE wITH ALL LOcAL, cITy AND STATE BUILDING cODES. BEFORE MAKING THE ELEcTRIcAL cONNEcTION, MAKE SURE THAT MAIN pOwER SUppLy IS DIScONNEcTED. THE AppLIANcE, wHEN INSTALLED, MUST BE ELEcTRIcALLy GROUNDED IN AccORDANcE wITH LOcAL cODES OR, IN THE ABSENcE OF LOcAL cODES, wITH THE NATIONAL ELEcTRIcAL cODE ANSI/NFpA 70 (LATEST EDITION) A factory installed junction box is located on the lower right hand side of the firebox. Wiring must be fed to the junction box and... -
Page 17: Master Parts Distributor List
MASTER PARTS DISTRIBUTOR LIST To Order Parts Under Warranty, please contact your local Empire dealer. See the dealer locator at www.empirecomfort. com. To provide warranty service, your dealer will need your name and address, purchase date and serial number, and the nature of the problem with the unit. To Order Parts After the Warranty Period, please contact your dealer or one of the Master Parts Distributors listed below. This list changes from time to time. For the current list, please click on the Master Parts button at www.empirecomfort.com. Please note: Master Parts Distributors are independent businesses that stock the most commonly ordered Original Equipment repair parts for Heaters, Grills, and Fireplaces manufactured by Empire Comfort Systems Inc. Dey Distributing Victor Division of F. W. Webb Company 1401 Willow Lake Boulevard 200 Locust Street Vadnais Heights, MN 55101... -
Page 17: Master Parts Distributor List
MASTER pARTS DISTRIBUTOR LIST To Order Parts Under Warranty, please contact your local Empire dealer. See the dealer locator at www.empirecomfort. com. To provide warranty service, your dealer will need your name and address, purchase date and serial number, and the nature of the problem with the unit. To Order Parts After the Warranty Period, please contact your dealer or one of the Master Parts Distributors listed below. This list changes from time to time. For the current list, please click on the Master Parts button at www.empirecomfort.com. Please note: Master Parts Distributors are independent businesses that stock the most commonly ordered Original Equipment repair parts for Heaters, Grills, and Fireplaces manufactured by Empire Comfort Systems Inc. Dey Distributing Victor Division of F. W. Webb Company 1401 Willow Lake Boulevard 200 Locust Street Vadnais Heights, MN 55101... -
Page 18: Parts List
PARTS LIST PART NO. INDEX DESCRIPTION VFS32FB0F VFS36FB0F VFS42FB0F 17162 17162 17162 JUNCTION BOX ASSEMBLY R3492 R3492 R3492 RECEPTACLE R3491 R3491 R3491 COVER, JUNCTION BOX 25447 25447 25447 BLOWER COVER PLATE (QUANTITY 2) R7051 R7052 R7053 ROD, SCREEN (QUANTITY 2) 20468 21087 33607 HOOD R9292 R9292 R9292 HEARTH LEDGE, RIGHT R9293 R9293 R9293 HEARTH LEDGE, LEFT... -
Page 18: Parts List
pARTS LIST pART NO. INDEX DEScRIpTION VFS32FB0F VFS36FB0F VFS42FB0F 17162 17162 17162 JUNCTION BOX ASSEMBLY R3492 R3492 R3492 RECEPTACLE R3491 R3491 R3491 COVER, JUNCTION BOX 25447 25447 25447 BLOWER COVER PLATE (QUANTITY 2) R7051 R7052 R7053 ROD, SCREEN (QUANTITY 2) 20468 21087 33607 HOOD R9292 R9292 R9292 HEARTH LEDGE, RIGHT R9293 R9293 R9293 HEARTH LEDGE, LEFT... -
Page 19: Parts View
PARTS VIEW 33743-0-0314 Page 19... -
Page 19: Parts View
pARTS VIEw 33743-2-0315 Page 19... -
Page 20: Accessories
ACCESSORIES Accessory Description Model Numbers Fan Kit Designed to provide forced air flow. FBB5 Variable Speed Control Kit Wall mounted variable speed control for use SCV-1 with FBB5 blower Brick Liners Contact dealer for all available Liner for Firebox optional liner kits Fresh Air Kit Deluxe and Premium Fireboxes VFA2 Frame Kits 3-Piece Frame Kits Contact dealer for all available Black, Stainless Steel or Hammered Pewter optional frame kits... -
Page 20: Accessories
AccESSORIES Accessory Description Model Numbers Fan Kit Designed to provide forced air flow. FBB5 Variable Speed Control Kit Wall mounted variable speed control for use SCV-1 with FBB5 blower Brick Liners Contact dealer for all available Liner for Firebox optional liner kits Fresh Air Kit Deluxe and Premium Fireboxes VFA2 Frame Kits 3-Piece Frame Kits Contact dealer for all available Black, Stainless Steel or Hammered Pewter optional frame kits... - Page 21 AccESSORIES (continued) Extended 4" Hoods Extended hoods that extend out 2" farther than the standard hoods, to accommodate thicker surround Contact dealer for all avail- materials. able optional hood acces- sories Available as optional kits in Brass, Hammered Pew- ter, and Stainless Steel finishes. Contact dealer for all avail- Available as optional kits in Brass, Hammered Pew- Decorative Door Kits able optional frame kit ac- ter, and Stainless Steel finishes. cessories Contact dealer for all avail- Available as optional kits in Brass, Hammered Pew- Decorative Frame Kits able optional decorative ter, and Stainless Steel finishes. door kit accessories 33743-2-0315 Page 21...
- Page 21 ACCESSORIES (continued) Extended 4" Hoods Extended hoods that extend out 2" farther than the standard hoods, to accommodate thicker surround Contact dealer for all avail- materials. able optional hood acces- sories Available as optional kits in Brass, Hammered Pew- ter, and Stainless Steel finishes. Contact dealer for all avail- Available as optional kits in Brass, Hammered Pew- Decorative Door Kits able optional frame kit ac- ter, and Stainless Steel finishes. cessories Contact dealer for all avail- Available as optional kits in Brass, Hammered Pew- Decorative Frame Kits able optional decorative ter, and Stainless Steel finishes. door kit accessories 33743-0-0314 Page 21...
-
Page 22: Warranty
wARRANTy Empire Comfort Systems Inc. warranties this hearth product to be free from defects at the time of purchase and for the periods speci- fied below. Hearth products must be installed by a qualified technician and must be maintained and operated safely, in accordance with the instructions in the owner’s manual. This warranty applies to the original purchaser only and is not transferable. All warranty repairs must be accomplished by a qualified gas appliance technician. Limited Lifetime Parts Warranty with a Five-Year Limited Labor Warranty – Combustion Chamber and Heat Exchanger If the combustion chamber or heat exchanger (see parts list) fails because of defective workmanship or material, Empire will repair or replace at Empire’s option. Within five years from the date of purchase, Empire will pay reasonable labor to have the defective part repaired or replaced at Empire’s option. Limited Five-Year Parts & Labor Warranty – All Other Components (Except Remote Controls, Thermostats, Accessories and Replacement Parts) Should any part fail because of defective workmanship or material within five years from the date of purchase, Empire will repair or replace at Empire’s option. -
Page 22: Warranty
WARRANTY Empire Comfort Systems Inc. warranties this hearth product to be free from defects at the time of purchase and for the periods speci- fied below. Hearth products must be installed by a qualified technician and must be maintained and operated safely, in accordance with the instructions in the owner’s manual. This warranty applies to the original purchaser only and is not transferable. All warranty repairs must be accomplished by a qualified gas appliance technician. Limited Lifetime Parts Warranty with a Five-Year Limited Labor Warranty – Combustion Chamber and Heat Exchanger If the combustion chamber or heat exchanger (see parts list) fails because of defective workmanship or material, Empire will repair or replace at Empire’s option. Within five years from the date of purchase, Empire will pay reasonable labor to have the defective part repaired or replaced at Empire’s option. Limited Five-Year Parts & Labor Warranty – All Other Components (Except Remote Controls, Thermostats, Accessories and Replacement Parts) Should any part fail because of defective workmanship or material within five years from the date of purchase, Empire will repair or replace at Empire’s option. -
Page 23: Appliance Service History
AppLIANcE SERVIcE HISTORy Date Dealer Name Service Technician Name Service performed/Notes 33743-2-0315 Page 23... -
Page 23: Appliance Service History
APPLIANCE SERVICE HISTORY Date Dealer Name Service Technician Name Service Performed/Notes 33743-0-0314 Page 23... - Page 24 Empire Comfort Systems Inc. EMPIRE EMPIRE 918 Freeburg Ave. Belleville, IL 62220 If you have a general question about our products, please e-mail us at info@empirecomfort.com. If you have a service or repair question, please contact your dealer. Comfort Systems www.empirecomfort.com Page 24 33743-2-0315...
- Page 24 Empire Comfort Systems Inc. EMPIRE EMPIRE 918 Freeburg Ave. Belleville, IL 62220 If you have a general question about our products, please e-mail us at info@empirecomfort.com. If you have a service or repair question, please contact your dealer. Comfort Systems www.empirecomfort.com Page 24 33743-0-0314...