Page 1 2003 Chevrolet Silverado Owner Manual Seats and Restraint Systems ......1-1 Service and Appearance Care ......5-1 Front Seats Service ..........1-3 ............. 5-3 Rear Seats ..........1-8 Fuel ............5-4 Safety Belts ..........1-10 Checking Things Under Child Restraints ........
Page 2: How To Use This Manual
P.O. Box 07130 Detroit, MI 48207 GENERAL MOTORS, GM, the GM Emblem, How to Use This Manual CHEVROLET, the CHEVROLET Emblem and the name SILVERADO are registered trademarks of General Many people read their owner’s manual from beginning Motors Corporation.
Page 3 Safety Warnings and Symbols You will also ﬁnd a circle with a slash through it in this book. This safety You will ﬁnd a number of safety cautions in this book. symbol means “Don’t,” We use a box and the word CAUTION to tell you about “Don’t do this”...
Page 4: Features And Controls
Vehicle Damage Warnings Vehicle Symbols Also, in this book you will ﬁnd these notices: Your vehicle has components and labels that use symbols instead of text. Symbols, used on your vehicle, Notice: These mean there is something that could are shown along with the text describing the operation damage your vehicle.
Page 5 These are some examples of vehicle symbols you may ﬁnd on your vehicle:...
Page 6: Model Reference
Model Reference This manual covers these models: ® Regular Cab Pickup Extended Cab Pickup Crew Cab Chassis Cab...
Page 7: Seats And Restraint Systems
Section 1 Seats and Restraint Systems Front Seats ............1-3 Child Restraints ..........1-31 Manual Seats ..........1-3 Older Children ..........1-31 Power Seats ..........1-4 Infants and Young Children ......1-34 Power Lumbar ..........1-4 Child Restraint Systems .........1-38 Heated Seats ..........1-5 Where to Put the Restraint ......1-41 Reclining Seatbacks ........1-5 Top Strap ............1-42 Head Restraints ..........1-7...
Page 8 Section 1 Seats and Restraint Systems Air Bag Systems ..........1-64 Servicing Your Air Bag-Equipped Vehicle ..1-80 Where Are the Air Bags? .......1-66 Adding Equipment to Your Air Bag-Equipped When Should an Air Bag Inﬂate? ....1-68 Vehicle ............1-80 What Makes an Air Bag Inﬂate? .....1-69 Restraint System Check ........1-81 How Does an Air Bag Restrain? .....1-69 Checking Your Restraint Systems ....1-81...
Page 9: Front Seats
Front Seats Manual Seats CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you don’t want to.
Page 10: Power Seats
Power Seats If your vehicle has power reclining seats, you can use the vertical control to adjust the angle of the seatback. Move the reclining front seatback rearward or forward by moving the control toward the rear or the front of the vehicle.
Page 11 Heated Seats Reclining Seatbacks If your vehicle has this feature, the button used to control the driver’s heated seat is located on the driver’s door panel. The button used to control the passenger’s heated seat is located on the passenger’s door panel. To heat the entire seat, press the horizontal button.
Page 12 CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can’t do their job when you’re reclined like this. The shoulder belt can’t do its job. In a crash, you could go into it, receiving neck or other injuries.
Page 13: Head Restraints
Head Restraints Seatback Latches CAUTION: If the seatback isn’t locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked.
Page 14: Rear Seats
Rear Seats 2. Fold the seat cushion upward until it latches with the seatback. 3. Push and pull on the seat to make sure the seat is Rear Seat Operation (Extended Cab) secure. The extended cab’s rear seat can also be folded open Folding the Rear Seat for more seating space.
Page 15 Rear Seat Operation (Crew Cab) 2. After folding the seat cushion fully forward, pull the seatback forward and fold the seatback down until it is ﬂat. If the seatback cannot fold ﬂat because it The second row rear seat has a 60/40 split seat. Either interferes with the cushion, try moving the front seat side of the rear seat may be folded down to give forward and/or bringing the front seat more...
Page 16: Safety Belts
Safety Belts CAUTION: Safety Belts: They Are for Everyone It is extremely dangerous to ride in a cargo This part of the manual tells you how to use safety area, inside or outside of a vehicle. In a belts properly. It also tells you some things you should collision, people riding in these areas are more not do with safety belts.
Page 17: Why Safety Belts Work
Why Safety Belts Work A few crashes are mild, and some crashes can be so serious that even buckled up, a person wouldn’t survive. When you ride in or on anything, you go as fast as But most crashes are in between. In many of them, it goes.
Page 18 Put someone on it. Get it up to speed. Then stop the vehicle. The rider doesn’t stop. 1-12...
Page 19 The person keeps going until stopped by something. In or the instrument panel... a real vehicle, it could be the windshield... 1-13...
Page 20: Questions And Answers About Safety Belts
Questions and Answers About Safety Belts Won’t I be trapped in the vehicle after an accident if I’m wearing a safety belt? You could be – whether you’re wearing a safety belt or not. But you can unbuckle a safety belt, even if you’re upside down.
Page 21: How To Wear Safety Belts Properly
How to Wear Safety Belts Properly If I’m a good driver, and I never drive far from home, why should I wear safety belts? This part is only for people of adult size. You may be an excellent driver, but if you’re in an Be aware that there are special things to know about accident –...
Page 22: Driver Position
Driver Position 3. Pick up the latch plate and pull the belt across you. Don’t let it get twisted. This part describes the driver’s restraint system. The shoulder belt may lock if you pull the belt across you very quickly. If this happens, let the belt Lap-Shoulder Belt go back slightly to unlock it.
Page 23 5. To make the lap part tight, pull down on the buckle The lap part of the belt should be worn low and snug on end of the belt as you pull up on the shoulder belt. the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones.
Page 24 What’s wrong with this? CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should ﬁt against your body. The shoulder belt is too loose. It won’t give nearly as much protection this way.
Page 25 What’s wrong with this? CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Page 26 What’s wrong with this? CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied at the abdomen, not at the pelvic bones, and that could cause serious or fatal injuries.
Page 27 What’s wrong with this? CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury. Also, the belt would apply too much force to the ribs, which aren’t as strong as shoulder bones.
Page 28 What’s wrong with this? CAUTION: You can be seriously injured by a twisted belt. In a crash, you wouldn’t have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to ﬁx it.
Page 29: Safety Belt Use During Pregnancy
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they don’t wear safety belts. To unlatch the belt, just push the button on the buckle. The belt should go back out of the way.
Page 30: Center Passenger Position
Center Passenger Position The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it’s more likely that the fetus won’t be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly.
Page 31: Lap Belt
Lap Belt When you sit in a center rear seat position of an extended cab or in the center front seat position of either a crew cab or an extended cab, you have a lap belt. To make the belt shorter, pull its free end as shown until the belt is snug.
Page 32: Rear Seat Passengers
Rear Seat Passengers It’s very important for rear seat passengers to buckle up! Accident statistics show that unbelted people in the rear seat are hurt more often in crashes than those who are wearing safety belts. Rear passengers who aren’t safety belted can be thrown out of the vehicle in a crash.
Page 33 When the shoulder belt is pulled out all the way, it will lock. If it does, let it go back all the way and start again. If the belt is not long enough, see Safety Belt Extender on page 1-31 . Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.
Page 34 The safety belt locks if there’s a sudden stop or a crash. The safety belt also locks if you pull the belt very quickly out of the retractor. CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Page 35: Rear Safety Belt Comfort Guides For Children And Small Adults
Rear Safety Belt Comfort Guides for Children and Small Adults Your vehicle may have this feature already. If it doesn’t, you can get it from any GM dealer. Rear seat comfort guides provide added safety belt comfort for older children who have outgrown booster seats and for small adults.
Page 36 3. Be sure that the belt is not twisted and it lies ﬂat. 4. Buckle, position and release the safety belt as The guide must be on top of the belt. described in Rear Seat Passengers on page 1-26 . Make sure that the shoulder belt crosses the shoulder.
Page 37: Safety Belt Extender
Safety Belt Extender Child Restraints If the vehicle’s safety belt will fasten around you, you Older Children should use it. But if a safety belt isn’t long enough to fasten, your dealer will order you an extender. It’s free. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you.
Page 38 What is the proper way to wear safety belts? If possible, an older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should ﬁt snugly below the hips, just touching the top of the thighs.
Page 39 What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt CAUTION: is very close to the child’s face or neck? If the child is sitting in a rear outside seat position, Never do this.
Page 40: Infants And Young Children
CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt.
Page 41 Every time infants and young children ride in vehicles, they should have the protection provided by appropriate CAUTION: restraints. Young children should not use the vehicle’s adult safety belts alone, unless there is no other choice. Instead, they need to use a child restraint. People should never hold a baby in their arms while riding in a vehicle.
Page 42 CAUTION: Children who are up against, or very close to, any air bag when it inﬂates can be seriously injured or killed. Air bags plus lap-shoulder belts offer outstanding protection for adults and older children, but not for young children and infants.
Page 43 For most basic types of child restraints, there are many different models available. When purchasing a CAUTION: child restraint, be sure it is designed to be used in a motor vehicle. If it is, the restraint will have a label saying that it meets federal motor vehicle The body structure of a young child is quite safety standards.
Page 44: Child Restraint Systems
Child Restraint Systems A rear-facing infant seat (B) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, An infant car bed (A), a special bed made for use in a acts to keep the infant positioned in the restraint.
Page 45 A forward-facing child seat (C-E) provides restraint for A booster seat (F-G) is a child restraint designed to the child’s body with the harness and also sometimes improve the ﬁt of the vehicle’s safety belt system. Some with surfaces such as T-shaped or shelf-like shields. booster seats have a shoulder belt positioner, and some high-back booster seats have a ﬁve-point harness.
Page 46 When choosing a child restraint, be sure the child How do child restraints work? restraint is designed to be used in a vehicle. If it is, it will have a label saying that it meets federal motor A child restraint system is any device designed for vehicle safety standards.
Page 47: Where To Put The Restraint
Where to Put the Restraint CAUTION: (Continued) Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. Even though the Passenger Sensing System General Motors, therefore, recommends that child restraints be secured in a rear seat including an infant and/or AIR BAG OFF switch are designed to riding in a rear-facing infant seat, a child riding in a turn off the passenger’s frontal air bag under...
Page 48: Top Strap
Top Strap There is limited space in the rear seating area of an extended cab model. If you need to secure a child restraint in a rear seating position of an extended cab Some child restraints have a top strap or 'top tether'. It model, especially in the rear center position, be sure to can help restrain the child restraint during a collision.
Page 49 In Canada, the law requires that forward-facing child restraints have a top strap, and that the strap be anchored. In the United States, some child restraints also have a top strap. If your child restraint has a top strap, it should be anchored. Anchor the top strap to one of the following anchor points.
Page 50: Top Strap Anchor Location
Top Strap Anchor Location Right Front Passenger Position Top Strap Anchor (All Models) If your vehicle is a regular cab model, there is also a top strap anchor for the right front passenger position located on the back panel of your vehicle, behind the right front passenger seat.
Page 51 Rear Seat Top Strap Anchors (Extended Cab Models) When using a child restraint with a top strap in either rear outboard position, raise the head restraint and route the top strap through the fabric loop on the seatback. Then, attach the top strap to the anchor point at If your vehicle is an extended cab model, you’ll ﬁnd the the center rear seating position.
Page 52: Crew Cab Models
Rear Seat Top Strap Anchors (Crew Cab Models) When using a child restraint with a top strap in the center rear position, route the top strap through the fabric loop on the seatback. Then, raise the head restraint and attach the top strap to the anchor If your vehicle is a Crew Cab model, you’ll ﬁnd top strap point located at the closest outboard position.
Page 53 Lower Anchorages and Top Tethers Your vehicle has the LATCH system. You will ﬁnd anchors (A) for the front passenger and the center rear for Children (LATCH System) seating positions. This system, designed to make installation of child restraints easier, does not use the vehicle’s safety belts. Instead, it uses vehicle anchors (A, B) and child restraint attachments to secure the restraints.
Page 54 In order to use the LATCH system in your vehicle, you need a child restraint designed for that system. To assist you in locating the lower anchors for this child restraint system, each seating position with the LATCH system has a visible metal anchor point in the seat where the seatback meets the seat cushion.
Page 55: Securing A Child Restraint Designed For The Latch System
Securing a Child Restraint Designed CAUTION: for the LATCH System 1. Find the anchors for the seating position you want If a LATCH-type child restraint isn’t attached to to use, where the bottom of the seatback meets the its anchorage points, the restraint won’t be back of the seat cushion.
Page 56: Securing A Child Restraint In A Rear Outside Seat Position
Securing a Child Restraint in a Rear If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for Outside Seat Position Children (LATCH System) on page 1-47 . See Top Strap on page 1-42 if the child restraint has one. Extended Cab and Crew Cab If your child restraint does not have the LATCH system, you’ll be using the lap-shoulder belt to secure the child...
Page 57 3. Buckle the belt. Make sure the release button is 4. Pull the rest of the shoulder belt all the way out of positioned so you would be able to unbuckle the the retractor to set the lock. safety belt quickly if you ever had to. 1-51...
Page 58: Securing A Child Restraint In A Center Rear Seat Position
To remove the child restraint, just unbuckle the vehicle’s safety belt and let it go back all the way. The safety belt will move freely again and be ready to work for an adult or larger child passenger. Securing a Child Restraint in a Center Rear Seat Position 5.
Page 59: Crew Cab
Crew Cab When you secure a child restraint in the center rear seat position of a crew cab, you’ll be using a lap-shoulder belt that works the same way as the safety belts in the rear outside seat positions. For instructions on how to secure a child restraint using a lap-shoulder belt see Securing a Child Restraint in a Rear Outside Seat Position on page 1-50 .
Page 60 4. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 5. To tighten the belt, pull its free end while you push down on the child restraint. If you’re using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push the child restraint as you tighten the belt.
Page 61: Securing A Child Restraint In The Right Front Seat Position
Securing a Child Restraint in the Your vehicle has a right front passenger air bag. Never put a rear-facing child restraint in the right front Center Front Seat Position passenger’s seat. Here’s why: CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s air bag inﬂates.
Page 62 A rear seat is a safer place to secure a forward-facing child restraint. If you need to secure a forward-facing child restraint in the right front seat position, see Where to Put the Restraint on page 1-41 . If your child restraint does not have the LATCH system, you’ll be using the lap-shoulder belt to secure the restraint in this position.
Page 63 5. Pull the rest of the shoulder belt all the way out of 6. To tighten the belt, feed the shoulder belt back into the retractor to set the lock. the retractor while you push down on the child restraint. If you’re using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 64 To remove the child restraint, just unbuckle the vehicle’s safety belt and let it go back all the way. The safety CAUTION: belt will move freely again and be ready to work for an adult or larger child passenger. A child in a rear-facing child restraint can be Securing a Child Restraint in the seriously injured or killed if the right front passenger’s air bag inﬂates.
Page 65 Never put a rear facing child restraint in the right front passenger’s seat unless the air bag is off. Here is why: CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s air bag inﬂates.
Page 66 A rear seat is a safer place to secure a forward facing child restraint. See Where to Put the Restraint on CAUTION: (Continued) page 1-41 . If you need to secure a forward-facing child restraint in the right front seat position, move the anyone whom the national government has seat as far back as it will go before securing a identiﬁed as a member of a passenger air bag...
Page 67 If your child restraint does not have the LATCH system, you will be using the lap-shoulder belt to secure the child restraint in this position. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say.
Page 68 5. Pull the rest of the shoulder belt all the way out of 6. To tighten the belt, feed the shoulder belt back into the retractor to set the lock. the retractor while you push down on the child restraint. If you are using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 69 8. If your vehicle has the passenger sensing system and you are using a rear-facing child restraint in CAUTION: this seat, check to be sure the right front passenger’s frontal air bag is off before you begin to drive. If the air bag is off, the off indicator If the air bag ON indicator comes on when you will be lit and stay lit in the inside rearview mirror have a rear-facing child restraint installed in...
Page 70: Air Bag Systems
Air Bag Systems To remove the child restraint, just unbuckle the vehicle’s safety belt and let it go back all the way. The safety belt will move freely again and be ready to work for an This part explains the air bag system. adult or larger child passenger.
Page 71 CAUTION: (Continued) CAUTION: ejected from it. Air bags are designed to work Air bags inﬂate with great force, faster than the with safety belts, but don’t replace them. Air blink of an eye. If you’re too close to an bags are designed to deploy only in moderate inﬂating air bag, as you would be if you were to severe frontal and near frontal crashes.
Page 72: Where Are The Air Bags
The system checks the air bag electrical system for malfunctions. The light tells you if there is an electrical CAUTION: problem. See Air Bag Readiness Light on page 3-36 for more information. Anyone who is up against, or very close to, Where Are the Air Bags? any air bag when it inﬂates can be seriously injured or killed.
Page 73 CAUTION: If something is between an occupant and an air bag, the bag might not inﬂate properly or it might force the object into that person causing severe injury or even death. The path of an inﬂating air bag must be kept clear. Don’t put anything between an occupant and an air bag, and don’t attach or put anything on the steering wheel hub or on or near any other air...
Page 74: When Should An Air Bag Inﬂate
When Should an Air Bag Inﬂate? on it, then your vehicle does not have the passenger sensing system and it has single stage air bags. See Passenger Air Bag Status Indicator on page 3-40 An air bag is designed to inﬂate in a moderate to severe or Passenger Sensing System on page 1-76 .
Page 75: How Does An Air Bag Restrain
Seat Position Sensors What Makes an Air Bag Inﬂate? Vehicle’s with dual stage air bags are also equipped In an impact of sufficient severity, the air bag sensing with special sensors which enable the sensing system to system detects that the vehicle is in a crash. The monitor the position of both the driver and passenger sensing system triggers a release of gas from the front seats.
Page 76: What Will You See After An Air Bag Inﬂates
What Will You See After an Air Bag CAUTION: Inﬂates? After an air bag inﬂates, it quickly deﬂates, so quickly When an air bag inﬂates, there is dust in the that some people may not even realize the air bag air.
Page 77: Air Bag Off Switch
• Air Bag Off Switch Your vehicle is equipped with electronic frontal sensors which help the sensing system distinguish Regular Cab and Extended Cab Models between a moderate and a more severe frontal impact. Your vehicle is also equipped with a crash If your vehicle is a regular cab model or an extended cab sensing and diagnostic module, which records model, it has a switch on the instrument panel that you...
Page 78 United States without Passenger Sensing System Canada with Passenger Sensing System 1-72...
Page 79 This switch should only be turned to AIR BAG OFF if the person in the right front passenger’s position is a member of a passenger risk group identiﬁed by the national government as follows: Infant. An infant (less than 1 year old) must ride in the front seat because: •...
Page 80 Medical Condition. A passenger has a medical condition which, according to his or her physician: • causes the passenger air bag to pose a special risk for the passenger; and • makes the potential harm from the passenger air bag in a crash greater than the potential harm from turning off the air bag and allowing the passenger, even if belted, to hit the dashboard or windshield in a crash.
Page 81 To turn off the right front passenger’s air bag, insert your ignition key into the switch, push in, and move the switch to the off position. The AIR BAG OFF light will come on to let you know that the right front passenger’s air bag is off. The right front passenger’s air bag will remain off until you turn it back on again, and the AIR BAG OFF light will stay on to remind you that the air bag is off.
Page 82: Passenger Sensing System
To turn the right front passenger’s air bag on again, insert your ignition key into the switch, push in, and move the switch to the ON or AUTO position. Passenger Sensing System If your rearview mirror has one of the indicators pictured in the following illustrations, your vehicle has a passenger Passenger sensing system.
Page 83 Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. CAUTION: (Continued) General Motors, therefore, recommends that child restraints be secured in a rear seat, including an infant Even though the passenger sensing system is riding in a rear-facing infant seat, a child riding in a forward-facing child seat and an older child riding in a designed to turn off the passenger’s frontal air...
Page 84 • The passenger sensing system is designed to enable the right front passenger seat is occupied by a (may inﬂate) the right front passenger’s frontal air smaller person, such as a child who has outgrown bag anytime the system senses that a person of adult child restraints size is sitting properly in the right front passenger’s seat.
Page 85 CAUTION: (Continued) vehicle serviced promptly, because an adult-size person sitting in the right front passenger’s seat may not have the protection of the frontal air bag. See “Air Bag Readiness Light” in the Index for more on this, including important safety information. Aftermarket equipment, such as seat covers, can affect how well the passenger sensing system operates.
Page 86: Servicing Your Air Bag-Equipped Vehicle
Servicing Your Air Bag-Equipped Adding Equipment to Your Air Vehicle Bag-Equipped Vehicle Air bags affect how your vehicle should be serviced. There are parts of the air bag system in several places Is there anything I might add to the front of the around your vehicle.
Page 87: Restraint System Check
Restraint System Check What if I added a snow plow? Will it keep the air bags from working properly? Checking Your Restraint Systems We’ve designed our air bag systems to work properly under a wide range of conditions, Now and then, make sure the safety belt reminder light including snow plowing with vehicles equipped and all your belts, buckles, latch plates, retractors with the optional Snow Plow Prep Package (RPO...
Page 88: Replacing Restraint System Parts After A Crash
Replacing Restraint System Parts If you’ve had a crash, do you need new belts or LATCH system parts? After a Crash After a very minor collision, nothing may be necessary. But if the belts were stretched, as they would be if worn during a more severe crash, then you need new parts.
Page 89: Table Of Contents
Section 2 Features and Controls Keys ...............2-3 Starting and Operating Your Vehicle ....2-20 Remote Keyless Entry System ......2-4 New Vehicle Break-In ........2-20 Remote Keyless Entry System Operation ...2-5 Ignition Positions ..........2-20 Starting Your Engine ........2-22 Doors and Locks ..........2-7 Engine Coolant Heater ........2-24 Door Locks ............2-7 Automatic Transmission Operation ....2-25 Power Door Locks ..........2-8...
Page 90 Section 2 Features and Controls ® Automatic Dimming Rearview Mirror with OnStar System ..........2-62 Compass and Temperature Display ....2-56 Storage Areas ..........2-64 Outside Manual Mirrors ........2-59 Glove Box ...........2-64 Outside Camper-Type Mirrors ......2-59 Cupholder(s) ..........2-64 Outside West Coast-Type Mirrors ....2-59 Front Storage Area ........2-65 Outside Power Mirrors ........2-60 Center Console Storage Area ......2-65...
Page 91 Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. A child or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. Do not leave the keys in a vehicle with children.
Page 92: Remote Keyless Entry System
Remote Keyless Entry System Your vehicle has one double-sided key for the ignition and all door locks If equipped, the remote keyless entry system operates as well as the spare tire on a radio frequency subject to Federal Communications hoist lock (if equipped). Commission (FCC) Rules and with Industry Canada.
Page 93: Remote Keyless Entry System Operation
• lamps will ﬂash and the interior lights will come on. Check the distance. You may be too far from your vehicle. You may need to stand closer during LOCK: Pressing this button once will lock all of the rainy or snowy weather. doors.
Page 94: Battery Replacement
new transmitter, the lost transmitter will not unlock your To replace the battery in the keyless entry transmitter vehicle. Each vehicle can have a maximum of do the following: four transmitters matched to it. Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about two years.
Page 95: Doors And Locks
Resynchronization Doors and Locks Resynchronization may be necessary due to the security method used by this system. The transmitter Door Locks does not send the same signal twice to the receiver. The receiver will not respond to a signal that has been sent previously.
Page 96: Power Door Locks
Power Door Locks There are several ways to lock and unlock your vehicle. You can use the keyless entry system (if equipped). If your vehicle has this You can also use your key. power door lock switch, press the raised side of the To lock the door from the switch, with the lock inside, slide the lever...
Page 97 Delayed Locking If your vehicle has this power door lock switch, press the bottom of the If your vehicle is a Crew Cab, it may be equipped with switch on either front this feature. When you lock the doors using the door to lock all the doors power lock switch or the remote keyless entry at once.
Page 98: Programmable Automatic Door Locks
Programmable Automatic Door 1. Begin with the ignition off. Then pull the turn signal/multifunction lever toward you and hold Locks it there while you perform the next step. 2. Turn the key to RUN then back to LOCK twice. Your vehicle may be equipped with an automatic Then, with the key in LOCK, release the turn lock/unlock feature which enables you to program your signal/multifunction lever.
Page 99: Programmable Unlocking Feature
Programmable Unlocking Feature 2. Turn the key to RUN and LOCK twice. Then, with the key in LOCK, release the turn The following is the list of available programming signal/multifunction lever. Once you do this, the options: doors will lock and unlock, the horn will chirp twice, and a 30-second timer will begin.
Page 100: Rear Door Security Locks
Rear Door Security Locks This feature is located on the inside edge of the rear doors. (Crew Cab) 1. To use one of the locks do the following: With this feature, you can lock the rear side doors so 2. Open one of the rear doors. that they cannot be opened from the inside by 3.
Page 101: Rear Doors
Rear Doors To open a rear access door from the inside, the front door must be opened Your vehicle may be equipped with a rear access ﬁrst. Then, use the door(s) that allows easier access to the rear area of the handle located on the extended cab.
Page 102: Tailgate Removal
Tailgate Removal 2. With the tailgate at a slight upward angle, The tailgate on your vehicle can be removed to allow for pull back on the tailgate different loading situations. Although the tailgate can at the right edge and be removed without assistance, you may want someone then move the to assist you with the removal to avoid possible tailgate to the right to...
Page 103: Manual Windows
Windows CAUTION: Leaving children in a vehicle with the windows closed is dangerous. A child can be overcome by the extreme heat and can suffer permanent injuries or even death from heat stroke. Never leave a child alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 104: Power Windows
Power Windows The driver’s door has a switch for the passenger window as well. Your power windows will work when the ignition has been turned to ACCESSORY or RUN or when Retained Accessory Power (RAP) is active. See ″Retained Accessory Power″ under Ignition Positions on page 2-20 .
Page 105: Sun Visors
Lock-Out Switch Swing-Out Windows ® If you have power windows on a Crew Cab , the To open a rear swing-out driver’s door power window switch has a lockout feature. window, ﬂip the latch open The lockout switch is located in front of the window and swing the glass out.
Page 106 Theft-Deterrent Systems If the delayed locking feature is active, the alarm will not be activated until all doors are closed Vehicle theft is big business, especially in some cities. and the security light goes off. Although your vehicle has a number of theft-deterrent 3.
Page 107: Testing The Alarm
® Passlock If you set off the alarm by accident, unlock any door with the key. You can also turn off the alarm by pressing UNLOCK on the remote keyless entry transmitter or Your vehicle is equipped with the ® by placing the key in the ignition and turning it to Passlock theft-deterrent system.
Page 108: Starting And Operating Your Vehicle
Starting and Operating Your Ignition Positions Vehicle With the key in the ignition switch, you can turn it to four different positions. New Vehicle Break-In Notice: Your vehicle doesn’t need an elaborate “break-in.” But it will perform better in the long run if you follow these guidelines: •...
Page 109: Key Release Button (Manual Transmission)
Key Release Button (Manual Transmission) CAUTION: The ignition key cannot be On manual transmission vehicles, turning the removed from the ignition key to LOCK will lock the steering column and of manual transmission result in a loss of ability to steer the vehicle. vehicles unless the This could cause a collision.
Page 110: Manual Transmission
Retained Accessory Power (RAP) Notice: Do not try to shift to PARK (P) if your vehicle is moving. If you do, you could damage the Your vehicle may be equipped with a Retained transmission. Shift to PARK (P) only when your Accessory Power (RAP) feature which will allow certain vehicle is stopped.
Page 111: Starting Your V8 Engine
Starting Your V8 Engine When starting your engine in very cold weather (below 0°F or −18°C), do this: 1. With your foot off the accelerator pedal, turn the 1. With your foot off the accelerator pedal, turn the ignition key to START. When the engine starts, ignition key to START and hold it there up to let go of the key.
Page 112: Engine Coolant Heater
Engine Coolant Heater CAUTION: In very cold weather, 0°F (−18°C) or colder, the Plugging the cord into an ungrounded outlet engine coolant heater can could cause an electrical shock. Also, the help. You’ll get easier starting and better wrong kind of extension cord could overheat fuel economy during and cause a ﬁre.
Page 113: Automatic Transmission Operation
Automatic Transmission Operation CAUTION: (Continued) If your vehicle is equipped with an automatic transmission, it features an electronic shift position You or others could be injured. To be sure indicator within the instrument panel cluster. This display your vehicle will not move, even when you are must be powered anytime the shift lever is capable of on fairly level ground, always set your parking being moved out of PARK (P).
Page 114 REVERSE (R): Use this gear to back up. If your vehicle ® is equipped with the Allison Transmission , the R CAUTION: may blink on the PRNDL if the shift inhibitor is active. Notice: Shifting to REVERSE (R) while your vehicle Shifting into a drive gear while your engine is is moving forward could damage your transmission.
Page 115 Drive (D) can be used when towing a trailer, carrying a If you manually select SECOND (2) in a light duty heavy load, driving on steep hills or for off-road automatic transmission, the transmission will drive in driving. You may want to shift the transmission to second gear.
Page 116: Automatic Transmission
Tow/Haul Mode Overdrive Disable ® (Automatic Transmission) (Allison Transmission ® Your vehicle may be equipped with a tow/haul mode. If your vehicle has an Allison Transmission you may The selector button is located on the end of the column have the overdrive disable feature. The overdrive disable shift lever.
Page 117: Manual Transmission Operation
If your vehicle has both tow/haul and overdrive disable FIRST (1). Then, slowly let up on the clutch pedal as you tap the button once to enable or disable tow/haul, press the accelerator pedal. Shift into FIRST (1) only and press and hold the button to enable or disable when the vehicle is below 5 mph (8 km/h).
Page 118 NEUTRAL: Use this position when you start or idle SECOND (2): Press the clutch pedal as you let up on your engine. the accelerator pedal and shift into SECOND (2). Then, slowly let up on the clutch pedal as you press the REVERSE (R): To back up, ﬁrst press down the clutch accelerator pedal.
Page 119 Six-Speed (VORTEC™ 8100 V8 and During the ﬁrst 500 miles (805 km) of vehicle use, start the vehicle moving in FIRST (1) gear. This allows DURAMAX™ 6600 V8 Engines) the clutch components to wear-in properly. Here’s how to operate your FIRST (1): With the vehicle at a stop, release the transmission.
Page 120: Shift Speeds
FOURTH (4), FIFTH (5) and SIXTH (6): Upshift into the Do not allow the engine rpm to overspeed and enter the higher forward gears the same way as you do tachometer red lines. Engine overspeed occurs when THIRD (3). Slowly let up on the clutch pedal as you downshifting, or descending a grade, at too high a press the accelerator pedal.
Page 121: Front Axle Locking Feature
Shift Light Four-Wheel Drive If your vehicle has four-wheel drive, you can send your If you have a manual transmission, you may engine’s driving power to all four wheels for extra traction. To get the most satisfaction out of four-wheel have a shift light.
Page 122: Manual Transfer Case
Manual Transfer Case An 4WD indicator light will illuminate when you shift into four-wheel drive and the front axle engages. Some delay between shifting and the indicator’s lighting is normal. Recommended Transfer Case Settings Transfer Case Settings Driving Conditions Normal The transfer case shift lever is on the ﬂoor to the right Severe of the driver.
Page 123 An indicator on the bezel near the lever shows you the NEUTRAL (N): Shift to this setting only when your transfer case settings: vehicle needs to be towed. See Recreational Vehicle Towing on page 4-55 or Towing Your Vehicle on 2-Wheel High (2HI): This setting is used for driving in page 4-55 .
Page 124 When Using the Manual Transfer Case Shifting In or Out of 4LO • All shifts should be made using quick motions. Slow Notice: Shifting the transfer case into 4LO while shifts may make it harder to shift. moving at speeds faster than 3 mph (5 km/h) •...
Page 125: Automatic Transfer Case
Automatic Transfer Case Recommended Transfer Case Settings Transfer Case Settings The transfer case buttons Driving AUTO are located to the left of Conditions the instrument panel cluster. Normal Variable Severe Extreme Vehicle in Tow* *See “Recreational Vehicle Towing” in the Index for further information.
Page 126 NEUTRAL: Shift the vehicle’s transfer case to (4HI): Use 4HI when you need extra traction, such NEUTRAL only when towing your vehicle. See a on snowy or icy roads or in most off-road situations. Recreational Vehicle Towing on page 4-55 or Towing This setting also engages your front axle to help Your Vehicle on page 4-55 for more information.
Page 127 Shifting into 2HI Shifting Out of 4LO Press and release the 2HI switch. This can be done at To shift from 4LO to 4HI, AUTO 4WD or 2HI your any speed (except when shifting from 4LO). vehicle must be stopped or moving less than 3 mph (4.8 km/h) with the transmission in NEUTRAL (N) and Shifting into 4LO the ignition in RUN.
Page 128 Shifting into NEUTRAL Shifting Out of NEUTRAL To shift the transfer case to NEUTRAL do the following: To shift out of NEUTRAL: 1. Set the parking brake and apply the regular brake 1. Make sure the vehicle is parked so that it will pedal.
Page 129: Electronic Transfer Case
Electronic Transfer Case Use these switches to shift into and out of four-wheel drive. You can choose among three driving settings: If your four-wheel-drive Recommended Transfer Case Settings vehicle has the electronic transfer case, the Transfer Case Settings transfer case switches are Driving Conditions located to the left of the instrument panel cluster.
Page 130 NEUTRAL: Shift the vehicle’s transfer case to (4LO): This setting also engages your front axle to NEUTRAL only when towing your vehicle. See give you extra traction. You may never need 4LO. It Recreational Vehicle Towing on page 4-55 or Towing sends the maximum power to all four wheels.
Page 131 Notice: Shifting the transmission into gear before Shifting into NEUTRAL the 4LO indicator light has stopped ﬂashing To shift the transfer case to NEUTRAL, ﬁrst make sure could damage the transfer case. To help avoid the vehicle is parked so that it will not roll: damaging your vehicle, always wait for the 4LO indicator light to stop ﬂashing before shifting your 1.
Page 132: Parking Brake
Shifting Out of NEUTRAL All-Wheel Drive To shift out of NEUTRAL: If your vehicle has the SS package, it may be equipped 1. Set the parking brake and apply the regular brake with all-wheel drive. With this feature, engine power pedal.
Page 133 To release the parking brake, hold the regular brake pedal down. Pull the bottom edge of the lever, located above the parking brake pedal, with the parking brake symbol, to release the parking brake. If the ignition is on when the parking brake is released, the brake system warning light will go off.
Page 134: Shifting Into Park (P)
Shifting Into Park (P) 2. Move the shift lever into PARK (P) position like this: CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll.
Page 135 3. Be sure the transfer case is in a drive gear – not in NEUTRAL (N). 4. Turn the ignition key to LOCK. 5. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P).
Page 136: Automatic Transmission Only
Leaving Your Vehicle With If you have to leave your vehicle with the engine running, be sure your vehicle is in PARK (P) and the the Engine Running parking brake is ﬁrmly set before you leave it. After you (Automatic Transmission Only) move the shift lever into PARK (P), hold the regular brake pedal down.
Page 137: Parking Your Vehicle
Shifting Out of Park (P) Parking Your Vehicle Your vehicle has an automatic transmission shift lock control system which locks the shift lever in PARK when CAUTION: the ignition is the LOCK position. You have to fully apply your regular brakes before you can shift from PARK (P) when the ignition is in RUN.
Page 138: Parking Over Things That Burn
Parking Over Things That Burn CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass or other things that can burn. 2-50...
Page 139: Engine Exhaust
Engine Exhaust CAUTION: (Continued) • CAUTION: Your vehicle was damaged when driving over high points on the road or over road debris. Engine exhaust can kill. It contains the gas • Repairs were not done correctly. carbon monoxide (CO), which you can not see •...
Page 140: Running Your Engine While You Are Parked
Running Your Engine While You CAUTION: Are Parked It’s better not to park with the engine running. But if you It can be dangerous to get out of your vehicle ever have to, here are some things to know. if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set.
Page 141: Manual Rearview Mirror
Automatic Dimming Rearview Mirror CAUTION: ® with OnStar , Compass and Temperature Display Four-wheel drive vehicles with the transfer Your vehicle may have this feature. When on, an case in NEUTRAL will allow the vehicle to roll, electrochromic mirror automatically dims to the proper even if your shift lever is in PARK (P).
Page 142: Temperature And Compass Display
Temperature and Compass Display Electrochromic Mirror Operation Press the on/off button, located to the far left, brieﬂy to The electrochromic (self dimming) mirror function is turn the comp/temp display on or off. turned on automatically each time the ignition is started. To operate the electrochromic mirror do the following: If the display reads CAL, you will need to calibrate the 1.
Page 143: Compass Variance
Compass Variance The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside of zone eight. Under certain circumstances, as during a long distance cross-country trip, it will be necessary to adjust for compass variance.
Page 144: Automatic Dimming Rearview Mirror With Compass And Temperature Display
Compass Calibration Cleaning the Mirror The compass may need calibration if one of the When cleaning the mirror, use a paper towel or similar following occurs: material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause •...
Page 145: Compass Operation
and °C. Press and release the TEMP button to toggle When cleaning the mirror, use a paper towel or similar between the Fahrenheit and Celsius readings. After material dampened with glass cleaner. Do not spray approximately four seconds of inactivity, the display will glass cleaner directly on the mirror as that may cause stop blinking and display the last selection made.
Page 146: Passenger Air Bag Indicator
Compass Variance The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside zone eight. Under certain circumstances, as during a long distance cross-country trip, it will be necessary to adjust for compass variance.
Page 147: Outside Manual Mirrors
Outside Manual Mirrors Outside West Coast-Type Mirrors Adjust your outside mirrors so you can just see the side If your vehicle is equipped with the west coast-type of your vehicle and have a clear view of objects mirrors, they can be adjusted so you can have a clear behind you.
Page 148: Outside Power Mirrors
Outside Power Mirrors The mirrors also include a memory function which works in conjunction with the memory seats. See “Memory Seats” in the Index for more information. If your vehicle is equipped with power outside mirrors, Outside Power Camper-Type Mirror the controls are located on the driver’s door If your vehicle is equipped with outside power...
Page 149: Outside Power Foldaway Mirrors
Outside Power Foldaway Mirrors Outside Curb View Assist Mirrors If your vehicle is equipped with outside power foldaway If your vehicle has the optional memory package mirrors the mirrors can be folded in toward the body you may have this feature. of the vehicle.
Page 150: Outside Convex Mirror
® Outside Convex Mirror OnStar System Your passenger’s side mirror is convex. A convex mirror’s surface is curved so you can see more from the driver’s seat. CAUTION: A convex mirror can make things (like other ® OnStar uses global positioning system (GPS) satellite vehicles) look farther away than they really are.
Page 151: Onstar Services
® OnStar Services Luxury and Leisure Plan • All Directions and Connections Plan services One of the following plans is normally included for a speciﬁc duration with each vehicle equipped with • Personal Concierge ® ® OnStar . You can upgrade or extend your OnStar ®...
Page 152: Storage Areas
® OnStar Steering Wheel Controls Storage Areas Your vehicle includes a number of storage : If your vehicle is compartments for storage of often-used items. equipped with the steering wheel control buttons Some vehicles have storage areas in the instrument you can use them panel.
Page 153: Front Storage Area
Front Storage Area Center Console Storage Area Your vehicle may have a center armrest storage Your vehicle may be equipped with a console compartment in the front bench seat. compartment between the bucket seats. To open it, fold down the armrest and press the latch To open it, press the button and swing the console lid handle located at the front of the armrest.
Page 154: Vehicle Personalization
Vehicle Personalization To store your memory seat, mirrors and radio presets, do the following: 1. Adjust the driver’s seat (including the seatback Memory Seat recliner, lumbar, and side wing area), both of the outside mirrors, and the radio station presets to your If your vehicle has this preference.
Page 155: Easy Exit Seat
The seat and mirror positions can also be recalled when To store the seat exit position for driver 1 or 2, do the placing the key in the ignition if programmed to do so following: through the Driver Information Center (DIC). 1.
Page 156 NOTES 2-68...
Page 157 Section 3 Instrument Panel Instrument Panel Overview .......3-4 Passenger Air Bag Status Indicator ....3-40 Hazard Warning Flashers ........3-6 Battery Warning Light ........3-42 Other Warning Devices ........3-6 Voltmeter Gage ..........3-42 Horn .............3-7 Up-Shift Light ..........3-43 Tilt Wheel .............3-7 Brake System Warning Light ......3-44 Turn Signal/Multifunction Lever ......3-7 Anti-Lock Brake System Warning Light .....3-45 Exterior Lamps ..........3-14...
Page 158 Section 3 Instrument Panel Audio System(s) ..........3-71 Audio Steering Wheel Controls ......3-122 Setting the Time for Radios without Radio DVD Distortion ..........3-122 Data Systems (RDS) ........3-72 Understanding Radio Reception ....3-123 Setting the Time for Radios with Radio Data Care of Your Cassette Tape Player ....3-123 Systems (RDS) .........3-72 Care of Your CDs and DVDs ......3-124 AM-FM Radio ..........3-72...
Page 159 NOTES...
Page 160: Instrument Panel Overview
Instrument Panel Overview...
Page 161 L. Hood Release. See Hood Release on page 5-9 . The main components of your instrument panel are the following: M. Steering Wheel Control Buttons (If Equipped). See Driver Information Center (DIC) on page 3-54 . A. Dome Lamp Button. See “Dome Lamps” under Interior Lamps on page 3-18 .
Page 162: Hazard Warning Flashers
Hazard Warning Flashers The hazard warning ﬂasher button is located at the top of the steering column. Your hazard warning ﬂashers work no matter what position your key is in, and even if the key isn’t in. Press the button to make the front and rear turn signal lamps ﬂash on and off.
Page 163: Horn
Horn Turn Signal/Multifunction Lever To sound the horn, press the center pad on the steering wheel. Tilt Wheel If your vehicle is equipped with a tilt wheel, it will allow you to adjust the steering wheel before you drive. You can raise it to the highest level to give your legs more room when you exit and enter your vehicle.
Page 164 Turn and Lane Change Signals If you move the lever all the way up or down, and the arrow ﬂashes at twice the normal rate, a signal bulb may The turn signal has two upward (for right) and two be burned out and other drivers may not see your downward (for left) positions.
Page 165 Headlamp High/Low Beam Changer Flash-To-Pass Feature To change the headlamps from low to high beam, push This feature allows you to use your high-beam the lever toward the instrument panel. To return the headlamps to signal a driver in front of you that you low-beam headlamps, pull the multifunction lever toward want to pass.
Page 166: Windshield Wipers
Windshield Wipers Windshield Washer There is a paddle marked with the windshield washer : OFF symbol at the top of the multifunction lever. To spray washer ﬂuid on the windshield, push the paddle. : MIST The wipers will clear the window and then either You control the windshield wipers by turning the band stop or return to your preset speed.
Page 167: Cruise Control
Cruise Control CAUTION: : Off • : On Cruise control can be dangerous where you can not drive safely at a steady speed. : Resume/Accelerate So, do not use your cruise control on winding roads or in heavy traffic. : Set •...
Page 168 Setting Cruise Control The cruise light on the instrument panel will illuminate when the cruise control is engaged. CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. Resuming a Set Speed You could be startled and even lose control.
Page 169 Increasing Speed While Using Cruise Passing Another Vehicle While Using Control Cruise Control There are two ways to go to a higher speed: Use the accelerator pedal to increase your speed. When you take your foot off the pedal, your vehicle will •...
Page 170: Exterior Lamps
Exterior Lamps AUTO (Automatic): Turning the control to this position puts the system into automatic headlamp mode. An indicator light will illuminate when this position is selected. (Parking Lamps): Turning the control to this position turns on the parking lamps, together with the following: •...
Page 171: Automatic Headlamp System
Automatic Headlamp System your instrument panel brightness control is in the full bright position. See “Instrument Panel Brightness When it is dark enough outside, your automatic headlamp Control” under Interior Lamps on page 3-18 . system will turn on your headlamps at the normal To idle your vehicle with the automatic headlamp system brightness along with other lamps such as the taillamps, off, turn the control to the off position.
Page 172: Fog Lamps
Fog Lamps The DRL system will come on when the following conditions are met: If your vehicle has fog lamps, use them for better vision • the ignition is on, in foggy or misty conditions. • the exterior lamps control is in AUTO, The fog lamp button is •...
Page 173: Cargo Lamp
Cargo Lamp The fog lamps will be cancelled after the ignition is turned off. If you still want to use the fog lamps after you restart the vehicle, you will need to press the fog The cargo lamp button is lamp button again located on the left side of the instrument panel.
Page 174: Interior Lamps
Interior Lamps Front Reading Lamps (If Equipped) Instrument Panel Brightness Control The reading lamps are located on the overhead console. : This feature controls the brightness of the instrument panel lights. The thumbwheel for this feature is located next to the headlamp control.
Page 175: Accessory Power Outlets
To use the outlet, lift the cover. When not using it, : You can use the dome override button, located always close the cover. below the exterior lamps control, to set the dome lamps to come on automatically when the doors are opened, Certain power accessory plugs may not be compatible or remain off.
Page 176: Ashtrays And Cigarette Lighter
Ashtrays and Cigarette Lighter Climate Controls Your vehicle may be equipped with a front ashtray Climate Control System located near the center of the instrument panel. Pull on the door to open it. Notice: Don’t put papers or other ﬂammable items into your ashtrays.
Page 177 (Off): If the fan is off, outside air will still enter the (Floor): This setting directs most of the air through vehicle, and will be directed based on the position of the ﬂoor outlets, and the rest of the air is divided the mode knob.
Page 178: Dual Climate Control System
Dual Climate Control System To change the current mode, select one of the following: (Vent): This mode directs air to the instrument With this system you can control the heating, cooling panel vents. and ventilation for your vehicle. (Bi-Level): This mode directs half of the air to the instrument panel vents;...
Page 179: Defogging And Defrosting
Defogging and Defrosting Temperature Control Driver’s Side: The lever on the left side of the climate Fog on the inside of the windows is a result of high control panel is used to raise or lower the temperature humidity (moisture) condensing on the cool window on the driver’s side of the vehicle.
Page 180: Rear Window Defogger
Rear Window Defogger Outlet Adjustment The lines you see on the rear window warm the glass. Use the air outlets located The rear window defogger uses a warming grid to in the center and on the remove fog from the rear window. side of your instrument <...
Page 181: Dual Automatic Climate Control System
Operation Tips Dual Automatic Climate Control • System Keep the hood and front air inlets free of ice, snow, or any other obstruction (such as leaves). The With this system, you can control the heating, cooling heater and defroster will work far better, reducing and ventilation in your vehicle.
Page 182: Automatic Operation
Driver’s Side Temperature Knob Turn the knob counterclockwise or clockwise to lower or increase the cabin temperature. The display will show The driver’s side knob is used to adjust the temperature the temperature setting decreasing or increasing and an of the air coming through the system on the driver’s arrow pointing to the passenger will be displayed side.
Page 183 If the driver and passenger’s temperature settings Be careful not to cover the sensor located on the are not the same, the opposite side temperature top of the instrument panel near the windshield. This setting will be displayed for an additional ﬁve sensor regulates air temperature based on sun seconds.
Page 184: Manual Operation
Manual Operation (Panel): This setting will deliver air to the instrument panel outlets. You may manually adjust the air delivery mode or fan speed. (Bi-Level): This setting will deliver warmer air to the ﬂoor and cooler air to the instrument panel outlets. (Fan): The switch with the fan symbol allows you to manually adjust the fan speed.
Page 185 Display If you select recirculation while in defrost, defog or ﬂoor, the light in the button will ﬂash and then go out to let you If you press the MODE button to select an air delivery know that this is not allowed. This is normal and helps to mode, the display will change to show you the selected prevent fogging.
Page 186: Air Conditioning
Air Conditioning On cool, but sunny days while using manual operation of the automatic system, use bi-level to deliver warm air to the ﬂoor and cooler air to the instrument (Air Conditioning): Press this button to turn the air panel outlets. To warm or cool the air delivered, turn the conditioning (A/C) compressor on and off.
Page 187 Defogging and Defrosting Rear Window Defogger You can use either defog or front defrost to clear fog or If your vehicle has this feature, the lines you see on the frost from your windshield. Use the defog mode to rear window warm the glass. The rear window clear the windows of fog or moisture.
Page 188: Operation Tips
Outlet Adjustment Operation Tips • Keep the hood and front air inlets free of ice, snow, or any other obstruction (such as leaves). The heater and defroster will work far better, reducing the chance of fogging the inside of your windows. •...
Page 189: Warning Lights, Gages And Indicators
Warning Lights, Gages and Gages can indicate when there may be or is a problem with one of your vehicle’s functions. Often gages Indicators and warning lights work together to let you know when there’s a problem with your vehicle. This part describes the warning lights and gages that When one of the warning lights comes on and stays on may be on your vehicle.
Page 190: Instrument Panel Cluster
Instrument Panel Cluster Your instrument cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, about how much fuel you have and many other things you’ll need to know to drive safely and economically. United States Heavy Duty Automatic Transmission version shown.
Page 191: Speedometer And Odometer
Speedometer and Odometer Engine Hour Meter Display The odometer can also display the number of hours the Your speedometer lets you see your speed in both engine has run. To display the hour meter, turn the miles per hour (mph) and kilometers per hour (km/h). ignition off, press and hold the reset button for at least Your odometer shows how far your vehicle has four seconds.
Page 192: Safety Belt Reminder Light
Safety Belt Reminder Light Air Bag Readiness Light When the key is turned to RUN or START, a chime will There is an air bag readiness light on the instrument come on for several seconds to remind people to panel cluster, which shows the air bag symbol. fasten their safety belts, unless the driver’s safety belt is The system checks the air bag’s electrical system for already buckled.
Page 193: Air Bag Off Light
Air Bag Off Light When you turn the right front passenger’s air bag off, this light will be lit and stay lit to remind you that the air bag has been turned off. This light will go off when you turn the air bag back on again. See Air Bag Off Switch on page 1-71 for more on this, including important safety information.
Page 194 Canada with Passenger Sensing System Canada without Passenger Sensing System 3-38...
Page 195 CAUTION: CAUTION: If the right front passenger’s air bag is turned If the air bag readiness light ever comes on off for a person who isn’t in a risk group when you have turned off the air bag, it means identiﬁed by the national government, that that something may be wrong with the air bag person won’t have the extra protection of an...
Page 196: Passenger Air Bag Status Indicator
Passenger Air Bag Status Indicator the status indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the right front passenger’s frontal air bag. If your vehicle has the passenger sensing system your rearview mirror will have a passenger air bag status If the word ON or the on symbol is lit on the passenger indicator.
Page 197 If the word OFF or the off symbol is lit on the passenger air bag status indicator, it means that the passenger CAUTION: sensing system or the air bag off switch has turned off the right front passenger’s air bag. See Passenger Sensing System on page 1-76 or Air Bag Off Switch on If the air bag off indicator and the air bag page 1-71 for more on this, including important safety...
Page 198: Battery Warning Light
Battery Warning Light Voltmeter Gage If this light is displayed When your engine is not when the engine is running, but the ignition is running, you may have a in RUN, this gage problem with your charging shows your battery’s state system.
Page 199: Up-Shift Light
Up-Shift Light Readings in the low warning zone may occur when a large number of electrical accessories are operating in the vehicle and the engine is left at an idle for an This light is used on some extended period. This condition is normal since the models with manual charging system is not able to provide full power transmissions.
Page 200: Brake System Warning Light
Brake System Warning Light This light should come on brieﬂy when you turn the ignition key to RUN. If it doesn’t come on then, have it ﬁxed so it will be ready to warn you if there’s a With the ignition on, the brake system warning light will problem.
Page 201: Anti-Lock Brake System Warning Light
Anti-Lock Brake System Warning If the light stays on, or comes on when you’re driving, your vehicle needs service. You will also hear a Light chime sound when the light is on steady. If the regular brake system warning light isn’t on, you still have brakes, but you don’t have anti-lock brakes.
Page 202: Traction Off Light
Traction Off Light • If you move the shift lever to FIRST (1), the light will come on and stay on to indicate that the traction system is off. This is normal operation. To If you have the Traction turn the system back on, move the shift lever Assist System, this light back to a position other than FIRST (1);...
Page 203: Engine Coolant Temperature Gage
Engine Coolant Temperature Gage Transmission Temperature Gage United States Canada United States Canada This gage shows the engine coolant temperature. Your vehicle may be equipped with a transmission temperature gage. It also provides an indicator of how hard your vehicle is working.
Page 204 See Driver Information Center (DIC) on page 3-54 for The following situations can cause the transmission to further information. operate at higher temperatures: • If your vehicle has an Allison transmission, and the ﬂuid Towing a trailer reaches temperatures of approximately 275°F (135°C) •...
Page 205: Malfunction Indicator Lamp
Malfunction Indicator Lamp Notice: Modiﬁcations made to the engine, transmission, exhaust, intake or fuel system of your vehicle or the replacement of the original tires Check Engine Light with other than those of the same Tire Performance Criteria (TPC) can affect your vehicle’s emission Your vehicle is equipped controls and may cause this light to come on.
Page 206: If The Light Is Flashing
If the Light is Flashing been left off or improperly installed. A loose or missing fuel cap will allow fuel to evaporate into the atmosphere. The following may prevent more serious damage to A few driving trips with the cap properly installed your vehicle: should turn the light off.
Page 207: Oil Pressure Gage
Emissions Inspection and Maintenance Oil Pressure Gage Programs Some state/provincial and local governments have or may begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Here are some things you need to know to help your vehicle pass an inspection: Your vehicle will not pass this inspection if the Check...
Page 208: Cruise Control Light
Cruise Control Light A reading in the low pressure zone may be caused by a dangerously low oil level or some other problem causing low oil pressure. Check your oil as soon as The cruise light comes on possible. See Oil Pressure Low under DIC Warnings whenever you set your and Messages on page 3-65 and Engine Oil on cruise control.
Page 209: Tow/Haul Mode Light
Tow/Haul Mode Light Fuel Gage This light is displayed when the tow/haul mode has been activated. For more information, see Towing a Trailer on page 4-68 . United States Canada Overdrive Disable When the ignition is on, the fuel gage tells you about how much fuel you have left in your tank.
Page 210: Low Fuel Warning Light
Driver Information Center (DIC) Here are some situations you may experience with your fuel gage. None of these indicate a problem with the fuel gage. The DIC display is located on the instrument panel cluster above the steering wheel. The DIC can display •...
Page 211: Trip Information Button
Trip Information Button C (Personalization): This button will change personal options available on your vehicle. Use the trip information button to scroll through the D (Select): This button resets certain functions and ODOMETER, PERSONAL TRIP ON/OFF, BUSINESS turns off or acknowledges messages on the DIC. TRIP ON/OFF, HOURMETER, ANNUAL LOG and TIMER.
Page 212 • To reset the personal or business trip information, do the PERSONAL: AVG MPH — This shows the vehicle’s following: press and hold select button for two seconds average speed for the personal trip. while in one of the personal or business trip modes. This •...
Page 213: Fuel Information Button
Annual Log Fuel Information Button Press the trip button, or the reset stem on the instrument Use the fuel information button to scroll through the panel cluster, to scroll to the annual log. The annual range, average fuel economy, instant fuel economy and log shows the mileage accumulated since it was the GM Oil Life System™.
Page 214: Maintenance Schedule
Instant Fuel Economy Personalization Button Press the fuel information button until INST appears in You can program certain features to a preferred setting the display. Instant fuel economy is how many miles for up to two people. Press the personalization button to per gallon your vehicle is at the particular moment scroll through the following personalization features.
Page 215: Automatic Locking
• ALARM WARNING: HORN: The horn will chirp when CURB VIEW ASSIST the alarm is active. • DISPLAY LANGUAGE ALARM WARNING: LAMPS: The headlamps will ﬂash • DISPLAY UNITS (ENG/MET) when the alarm is active. The default options for the above features were set Choose one of the four options and press the when your vehicle left the factory.
Page 216: Automatic Unlocking
Seat Position Recall LOCK DOORS OUT OF PARK (default): The doors will lock when the vehicle is shifted out of PARK (P). Press the personalization button until SEAT POSITION Choose one of the three options and press the RECALL appears on the display. To select your personalization button while it is displayed on the DIC to personalization for seat position recall, press the select select it and move on to the next feature.
Page 217: Perimeter Lighting
Perimeter Lighting transmitter, press the select button while REMOTE LOCK FEEDBACK is displayed on the DIC. Pressing Press the personalization button until PERIMETER the select button will scroll through the following choices: LIGHTING appears in the display. To select your personalization for perimeter lighting, press the select LOCK FEEDBACK: BOTH (default): The parking button while PERIMETER LIGHTING is displayed on the...
Page 218 Remote Unlock Feedback Headlamps on at Exit Press the personalization button until REMOTE Press the personalization button until HEADLAMPS ON UNLOCK FEEDBACK appears in the display. To select AT EXIT appears in the display. To select your your personalization for the feedback you will receive personalization for how long the headlamps will stay on when unlocking the vehicle with the remote keyless when you turn off the vehicle, press the select button...
Page 219: Curb View Assist
Curb View Assist Easy Exit Seat Press the personalization button until CURB VIEW Press the personalization button until EASY EXIT SEAT ASSIST appears in the display. To select your appears in the display. To select your personalization personalization for curb view assist, press the select for seat position exit, press the select button while EASY button while CURB VIEW ASSIST is displayed on EXIT SEAT is displayed on the DIC.
Page 220: Select Button
Display Units (ENG/MET) You can also scroll through the different languages by pressing and holding the trip reset stem for four seconds, Press the personalization button until DISPLAY UNITS as long as you are in the season odometer mode. appears in the display. To select English or metric, Choose one of the three options and press the press the select button while DISPLAY UNITS is personalization button while it is displayed on the DIC to...
Page 221: Dic Warnings And Messages
DIC Warnings and Messages Sensing System on page 1-76 . The message will come on and a chime will sound when the ignition is in RUN or ON and the following conditions occur: Warning messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and •...
Page 222: Check Oil Level
CHECK OIL LEVEL message still appears on the DIC. Press the select button to acknowledge the message and clear it from If the oil level in the vehicle is low, this message will the DIC display. appear on the DIC. Check and oil level and correct it as ENGINE COOLANT HOT necessary.
Page 223: Keyfob X Battery Low
KEYFOB X BATTERY LOW it until the cause of the low oil pressure has been corrected. Check your oil as soon as possible and have If a remote keyless entry transmitter battery is low, this your vehicle serviced. message will appear on the DIC. The battery needs OIL LIFE RESET to be replaced in the transmitter.
Page 224: Service Brake System
REDUCED ENGINE POWER SERVICE BRAKE SYSTEM This message is displayed when the cooling system If there is a problem with the brake system, this temperature gets too hot and the engine further enters message will be displayed on the DIC. If this message the engine coolant protection mode.
Page 225: Service 4 Wheel Steer
SERVICE 4 WHEEL STEER CAUTION: If a problem occurs with the 4 wheel steer system, this message will appear on the DIC. If this message appears, stop as soon as possible, and turn off the Your brake system may not be working vehicle.
Page 226: Tighten Fuel Cap
TIGHTEN FUEL CAP Notice: If you keep driving your vehicle with the transmission TRANS FLUID HOT message If the vehicle’s fuel cap is not tightened properly thsi displayed, you can damage the transmission. This message may appear along with the check engine light could lead to costly repairs that may not be covered on the instrument panel.
Page 227: Audio System(S)
TRANS HOT IDLE ENGINE (Allison Audio System(s) ® Transmission Only) Notice: Before you add any sound equipment to If the transmission ﬂuid in the vehicle gets hot, this your vehicle – like a tape player, CB radio, mobile message will appear on the DIC, and you will hear a telephone or two-way radio –...
Page 228: Setting The Time For Radios Without Radio
Setting the Time for Radios without AM-FM Radio Radio Data Systems (RDS) Press and hold the HR or MIN arrow for two seconds. Then press the HR (down) arrow until the correct hour appears on the display. Press and hold the MIN (up) arrow until the correct minute appears on the display.
Page 229: Finding A Station
Finding a Station Setting Preset Stations The six numbered pushbuttons let you return to your AM FM: Press this button to switch the display between favorite stations. You can set up to 18 stations (six AM, time and radio station frequency. Time display is six FM1 and six FM2) by performing the following available with the ignition turned off.
Page 230: Radio Messages
To adjust both tone controls and both speaker controls To adjust both tone controls and both speaker controls to the middle position, end out of audio by waiting to the middle position, end out of audio by waiting for the display to change to the time display. Then press for the display to change to the time display.
Page 231: Radio With Cd
Radio with CD • display messages from radio stations, and • seek to stations with traffic announcements. This system relies upon receiving speciﬁc information from these stations and will only work when the information is available. In rare cases, a radio station may broadcast incorrect information that will cause the radio features to work improperly.
Page 232: Playing The Radio
Playing the Radio releasing this knob, you may retrieve four different categories of information: Artist, Song Title, Category or PTY, Channel Number/Channel Name. PWR (Power): Press this knob to turn the system on and off. To change the default on the display, push this knob until you see the display you want, then hold the knob VOL (Volume): Turn this knob to increase or to for two seconds.
Page 233 To scan preset stations, press and hold one of the 5. Press and hold one of the six numbered arrows for more than four seconds. The radio will pushbuttons. The radio will produce one beep. produce two beeps. The radio will scan to the ﬁrst preset Whenever you press that numbered pushbutton, the station, play for a few seconds, then go on to the next station you set will return and the bass and treble...
Page 234 AUTO EQ (Automatic Equalization): Press this button To adjust all tone and speaker controls to the middle to choose bass and treble equalization settings position, push and hold the AUDIO knob when no tone designed for country/western, jazz, talk, pop, rock and or speaker control is displayed.
Page 235: Rds Messages
Setting Preset PTYs (RDS Only) SCAN: You can also scan through the channels within a category by performing the following: The six numbered pushbuttons let you return to your 1. Turn the P-TYPE LIST knob. TYPE and a PTY will favorite PTYs.
Page 236 ALERT! will not be affected by tests of the emergency If the current tuned station does not broadcast traffic broadcast system. This feature is not supported by announcements, press this button and the radio all RDS stations. will seek to a station that does. When the radio ﬁnds a station that broadcasts traffic announcements, it will INFO (Information): If the current station has a stop and TRAF will be displayed.
Page 237 XM™ Radio Messages Radio Display Condition Action Required Message XL (Explicit Language XL on the radio display, These channels, or any others, can be blocked at a Channels) after the channel name, customer’s request, by calling 1-800-852-XMXM (9696). indicates content with explicit language.
Page 238 XM™ Radio Messages (cont’d) Radio Display Condition Action Required Message No Info Category Name not No category information is available at this time on this available channel. Your system is working properly. No Info No Text/Informational No text or informational messages are available at this message available time on this channel.
Page 239: Playing A Compact Disc
Playing a Compact Disc 2 NEXT: Press this pushbutton to go to the next track. TRACK and the track number will appear on the Insert a disc partway into the slot, label side up. The display. If you hold this pushbutton or press it more than player will pull it in and the disc should begin playing.
Page 240: Compact Disc Messages
SEEK : Press the left arrow to go to the start of (Eject): Press this button to stop a CD when it is the current or to the previous track. Press the right playing or to eject a CD when it is not playing. Eject arrow to go to the start of the next track.
Page 241: Radio With Cassette And Cd
Radio with Cassette and CD • display messages from radio stations, and • seek to stations with traffic announcements. This system relies upon receiving speciﬁc information from these stations and will only work when the information is available. In rare cases, a radio station may broadcast incorrect information that will cause the radio features to work improperly.
Page 242 Playing the Radio For XM™ (USA only, if equipped), push this knob while in XM mode to retrieve various pieces of information related to the current song or channel. By pressing and PWR (Power): Press this knob to turn the system on releasing this knob, you may retrieve four different and off.
Page 243 3. Tune in the desired station. SCAN : Press and hold one of the arrows for more than two seconds. The radio will produce 4. Press AUTO EQ to choose the bass and treble one beep. The radio will scan to a station, play for a few equalization that best suits the type of station seconds, then go on to the next station.
Page 244 AUTO EQ (Automatic Equalization): Press this button To adjust all tone and speaker controls to the middle to choose bass and treble equalization settings position, push and hold the AUDIO knob when no tone designed for country/western, jazz, talk, pop, rock and or speaker control is displayed.
Page 245 SCAN: You can also scan through the channels within a 3. Turn the P-TYPE LIST knob to select a PTY. category by performing the following: 4. Press and hold one of the six numbered 1. Turn the P-TYPE LIST knob. TYPE and a PTY will pushbuttons until you hear a beep.
Page 246 If the whole message is not displayed, parts of it will will hear it. If no station is found, NO TRAFFIC will appear every three seconds. To scroll through the appear on the display. message at your own speed, press the INFO button If TRAF is on the display you can press the TRAF repeatedly.
Page 247 XM™ Radio Messages Radio Display Condition Action Required Message XL (Explicit Language XL on the radio display, These channels, or any others, can be blocked at a Channels) after the channel name, customer’s request, by calling 1-800-852-XMXM (9696). indicates content with explicit language.
Page 248 XM™ Radio Messages (cont’d) Radio Display Condition Action Required Message No Info Category Name not No category information is available at this time on this available channel. Your system is working properly. No Info No Text/Informational No text or informational messages are available at this message available time on this channel.
Page 249: Playing A Cassette Tape
Playing a Cassette Tape the position on the tape. If pressed when the current selection has been playing for more than 13 seconds, it Your tape player is built to work best with tapes that are will go to the beginning of the current selection. up to 30 to 45 minutes long on each side.
Page 250: Cassette Tape Messages
5 SIDE: Press this pushbutton to play the other side of (Eject): Press this button to stop a tape when it is the tape. playing or to eject a tape when it is not playing. Eject may be activated with the radio off. Cassette tapes may be SEEK : The right arrow is the same as the loaded with the radio off if this button is pressed ﬁrst.
Page 251: Cd Adapter Kits
Playing a Compact Disc CLEAN: If this message appears on the display, the cassette tape player needs to be cleaned. It will still play Insert a disc partway into the slot, label side up. The tapes, but you should clean it as soon as possible to player will pull it in and the disc should begin playing.
Page 252 2 NEXT: Press this pushbutton to go to the next track. SEEK : Press the left arrow to go to the start of TRACK and the track number will appear on the the current or to the previous track. Press the right display.
Page 253 Listening to a DVD (Eject): Press this button to stop a CD when it is playing or to eject a CD when it is not playing. Eject may If your vehicle has the Rear Seat Entertainment (RSE) be activated with either the ignition or radio off. CDs may system and a DVD is playing, the DVD symbol will be loaded with the radio and ignition off if this button is appear on the radio display indicating that the DVD is...
Page 254: Radio With Six-Disc Cd
Radio with Six-Disc CD • display messages from radio stations, and • seek to stations with traffic announcements. This system relies upon receiving speciﬁc information from these stations and will only work when the information is available. In rare cases, a radio station may broadcast incorrect information that will cause the radio features to work improperly.
Page 255 Playing the Radio To change the default on the display, push this knob until you see the display you want, then hold the knob until the display ﬂashes. The selected display will now be the PWR (Power): Push this knob to turn the system on default.
Page 256 Setting the Tone (Bass/Treble) To scan preset stations, press and hold either SCAN arrow for more than four seconds. PRESET SCAN will appear on the display. You will hear a double beep. AUDIO: Push the AUDIO knob until BASS or TREB The radio will go to a preset station stored on your appears on the display.
Page 257 Adjusting the Speakers (Balance/Fade) 4. If you want to go to another station within that category and the category is displayed, press either AUDIO: To adjust the balance between the right and the SEEK arrow once. If the category is not displayed, left speakers, push the AUDIO knob until BAL appears on press either SEEK arrow twice to display the the display.
Page 258 RDS Messages BAND (Alternate Frequency): Alternate frequency allows the radio to switch to a stronger station with the ALERT!: Alert warns of local or national emergencies. same program type. Press and hold BAND for two When an alert announcement comes on the current radio seconds to turn alternate frequency on.
Page 259 TRAF (Traffic): If TRAF appears on the display, the If the brackets are on the display and TRAF is not, you tuned station broadcasts traffic announcements. can then press the TRAF button to remove the To receive the traffic announcement from the tuned brackets or use the TUNE knob or the SEEK arrows to station, press this button.
Page 260 XM™ Radio Messages (cont’d) Radio Display Condition Action Required Message No Signal Loss of signal Your system is functioning correctly, but you are in a location that is blocking the XM signal. When you move into an open area, the signal should return. Loading XM Acquiring channel audio Your radio system is acquiring and processing audio and...
Page 261 XM™ Radio Messages (cont’d) Radio Display Condition Action Required Message XM Locked Theft lock active The XM receiver in your vehicle may have previously been in another vehicle. For security purposes, XM receivers cannot be swapped between vehicles. If you receive this message after having your vehicle serviced, check with the servicing facility.
Page 262 3. Once the light stops ﬂashing and turns green, load LOAD CD : Press the LOAD side of this button to a disc. Insert the disc partway into the slot, label load CDs into the compact disc player. This compact side up.
Page 263 Playing a Speciﬁc Loaded timer will reset at each press of eject, which will cause the receiver to not eject the disc until the 25-second time Compact Disc period has elapsed. For every CD loaded, a number will appear on the radio Once the player stops and the disc is ejected, remove the display.
Page 264 RDM (Random): With random, you can listen to the SCAN : To scan one disc, press and hold either tracks in random, rather than sequential, order, on one SCAN arrow for more than two seconds until SCAN disc or on all of the discs. To use random, do one appears on the display and you hear a beep.
Page 265: Using Song List Mode
Using Song List Mode If you attempt to save more than 20 selections, S-LIST FULL will appear on the display. The integrated six-disc CD changer has a feature called To play the song list, press the SONG LIST button. One song list.
Page 266 • To delete the entire song list, perform the following The air is very humid. If so, wait about an hour and steps: try again. 1. Turn the disc player on. • There may have been a problem while burning the CD.
Page 267: Rear Seat Entertainment System
Rear Seat Entertainment System If an error message appears on the video screen, see “DVD Messages” later in this section. Your vehicle may have the optional Digital Versatile Disc (DVD) Rear Seat Entertainment (RSE) system. The RSE system includes a DVD player, a video display screen, two sets of wireless headphones, and a remote control.
Page 268: Playing A Disc
Some DVDs will not allow you to fast forward or skip the (Play/Pause): Press this button to turn the DVD copyright or previews. Some DVDs will begin playing player on, to start play of a DVD or CD and to after the previews have ﬁnished.
Page 269: Video Screen
DVD Messages able to gain the attention of the rear seat passengers. Press this button again to restore normal operation The following errors may be displayed on the video of the DVD player. screen: This button may also be used to turn the DVD player •...
Page 270: Remote Control
Remote Control (Power): Press this button to turn the DVD player on or off. To use the remote control, aim it at the infrared window below the video screen and press the desired button. (Title): Press this button to return the DVD to the Direct sunlight or very bright light may affect the ability of main menu of the DVD.
Page 271 (Stop): Press this button to stop the play of a DVD (Return): Press this button to exit the current or CD. Press this button twice to return to the beginning active menu and return to the previous menu. This of the DVD. button will operate only when a DVD is being played and a menu is active.
Page 272 Headphones (Next Track/Chapter): Press this button to advance to the beginning of the next track or chapter. This The RSE system includes two sets of wireless infrared button may not work when the DVD is playing the headphones. copyright or the previews. Each set of headphones has an ON/OFF control.
Page 273: Stereo Rca Jacks
Notice: Do not store the headphones in heat or How to Change the Video Format when in direct sunlight. This could damage the headphones the Auxiliary Mode and repairs would not be covered by your warranty. The auxiliary input video format is preset to NTSC. In Keep the headphones stored in a cool, dry place.
Page 274 The RSE system is capable of outputting audio to the Problem Recommended Action vehicle speakers by using the radio. The RSE system No power. The ignition might not be may be selected as an audio source on the radio if the in on or accessory.
Page 275 Problem Recommended Action Problem Recommended Action In auxiliary mode, the Check the signal coming After stopping the player, I If the stop button was picture moves or scrolls. from the auxiliary device push Play but sometimes pressed one time, the and make sure that the the DVD starts where I DVD player will resume...
Page 276: Rear Seat Audio Controls
Rear Seat Audio Controls Problem Recommended Action Sometimes the wireless This could be caused by headphone audio cuts out interference from cellular or buzzes. telephone towers or by using your cellular telephone in the vehicle. I lost the remote and/or See your dealer for the headphones.
Page 277: Theft-Deterrent Feature
PROG (Program): The front passengers must be (Volume): Turn the knob to increase or to decrease listening to something different for each of these volume. The left knob controls the left headphone and functions to work: the right knob controls the right headphone. •...
Page 278: Audio Steering Wheel Controls
Audio Steering Wheel Controls SOURCE : Press this button to select AM, FM1, FM2, or XM1 or XM2, (USA only, if equipped), or a You can control certain radio functions using the buttons cassette tape or CD. The cassette or CD must be loaded on your steering wheel.
Page 279: Understanding Radio Reception
Understanding Radio Reception Care of Your Cassette Tape Player A tape player that is not cleaned regularly can cause reduced sound quality, ruined cassettes or a damaged The range for most AM stations is greater than for FM, mechanism. Cassette tapes should be stored in their especially at night.
Page 280: Care Of Your Cds And Dvds
When cleaning the cassette tape player with the After you clean the player, press and hold the eject recommended non-abrasive cleaning cassette, it is button for ﬁve seconds to reset the CLEAN indicator. possible that the cassette may eject, because the cut The radio will display --- or CLEANED to show the tape detection feature on your radio may recognize it as indicator was reset.
Page 281: Cleaning The Video Screen
Cleaning the Video Screen XM™ Satellite Radio Antenna System (48 Contiguous US States) Pour some isopropyl or rubbing alcohol on a clean cloth and gently wipe the video screen. Do not spray Your XM™ Satellite Radio antenna is located on the roof directly onto the screen and do not press too hard or of your vehicle.
Page 282 NOTES 3-126...
Page 283: Driving Your Vehicle
Section 4 Driving Your Vehicle Your Driving, the Road, and Your Vehicle ..4-2 Freeway Driving ...........4-43 Defensive Driving ...........4-2 Before Leaving on a Long Trip .......4-44 Drunken Driving ..........4-2 Highway Hypnosis ........4-45 Control of a Vehicle ........4-5 Hill and Mountain Roads ........4-46 Braking ............4-6 Winter Driving ..........4-48 Traction Assist System (TAS) ......4-10...
Page 284: Your Driving, The Road, And Your Vehicle
Your Driving, the Road, and proper defensive driving more difficult and can even cause a collision, with resulting injury. Ask a passenger to Your Vehicle help do things like this, or pull off the road in a safe place to do them yourself. These simple defensive driving techniques could save your life.
Page 285 Many adults — by some estimates, nearly half the adult same BAC by drinking three 4 ounce (120 ml) glasses population — choose never to drink alcohol, so they of wine or three mixed drinks if each had 1-1/2 ounces never drive after drinking.
Page 286 There is a gender difference, too. Women generally The body takes about an hour to rid itself of the alcohol have a lower relative percentage of body water in one drink. No amount of coffee or number of cold than men. Since alcohol is carried in body water, this showers will speed that up.
Page 287: Control Of A Vehicle
Control of a Vehicle CAUTION: You have three systems that make your vehicle go where you want it to go. They are the brakes, the steering and the accelerator. All three systems have to do their work at Drinking and then driving is very dangerous. the places where the tires meet the road.
Page 288: Braking
Braking and allow realistic following distances, you will eliminate a lot of unnecessary braking. That means better braking and longer brake life. Braking action involves perception time and reaction time. If your engine ever stops while you are driving, brake normally but do not pump your brakes.
Page 289 If there is a problem with the anti-lock brake system, this warning light will stay on. See Anti-Lock Brake System Warning Light on page 3-45 . Along with ABS, your vehicle has a Dynamic Rear Proportioning (DRP) system. If there is a DRP problem, both the brake and ABS warning lights will come on accompanied by a 10-second chime.
Page 290: Braking In Emergencies
The anti-lock system can change the brake pressure Remember: Anti-lock does not change the time you faster than any driver could. The computer is need to get your foot up to the brake pedal or always programmed to make the most of available tire and road decrease stopping distance.
Page 291: Supplemental Brake Assist System
Supplemental Brake Assist System Each time you start your vehicle and accelerate to 10 mph, the supplemental brake assist system If your vehicle has vacuum assist power brakes, it is also will perform a self-diagnostic check of the system and equipped with a supplemental brake assist system you may hear or feel the supplemental brake assist that supplies additional vacuum to the vacuum brake...
Page 292: Traction Assist System (Tas)
Traction Assist System (TAS) If your vehicle is in cruise control when the TAS begins to limit wheel spin, the cruise control will automatically disengage. When road conditions allow you to safely Your vehicle may have a Traction Assist System (TAS) use it again, you may re-engage the cruise control.
Page 293 The traction off light will come on under the following The Traction Assist System, as delivered from the conditions: factory, will automatically come on whenever you start your vehicle. To limit wheel spin, especially in • The Traction Assist System is turned off, either by slippery road conditions, you should always leave the pressing the TAS on/off button or turning off the system on.
Page 294: Manual Selectable Ride
Manual Selectable Ride If desired, you can change the TAS automatic engagement feature so that the system will not come on automatically when the engine is started. To do so: The main function of this system is to provide superior ride comfort while trailering or fully loaded, as well 1.
Page 295: Power Steering
• Locking Rear Axle For optimum ride comfort when trailering, fully loaded, driving off-road, or when personal If your vehicle has this feature, your locking rear axle can preferences demand more control the button should give you additional traction on snow, mud, ice, sand or be pressed in with the indicator light illuminated.
Page 296: Steering In Emergencies
Steering in Emergencies The traction you can get in a curve depends on the condition of your tires and the road surface, the angle at There are times when steering can be more effective which the curve is banked, and your speed. While than braking.
Page 297: Quadrasteer
QUADRASTEER™ The QUADRASTEER™ System has a control and diagnostic module that monitors and records current system status and operational information. If your vehicle is equipped with the 4 Wheel Steer system it has the ability to steer the vehicle with all four wheels.
Page 298 The 4 Wheel Steer system is equipped with 2: In this mode the vehicle will operate like any other three different driving modes: vehicle with two wheel steering. If you want to use 2 wheel steer mode and your vehicle is not in this mode, •...
Page 299 Slower Speeds (below 40 m.p.h./ 64 km/h ) Higher Speeds (40 m.p.h./64 km/h, and above) At slower speeds the front and rear wheels will turn in At higher speeds the front and rear wheels will turn in opposite directions. This helps the vehicle make the same direction.
Page 300 To engage the 4 Wheel Steer tow mode, press the button until the 4 and tow mode indicators light up on the instrument panel. If the tow indicator is ﬂashing you will have to center the steering wheel by turning it to the left or right.
Page 301: Off-Road Recovery
Off-Road Recovery Passing You may ﬁnd that your right wheels have dropped off The driver of a vehicle about to pass another on a the edge of a road onto the shoulder while you’re two-lane highway waits for just the right moment, driving.
Page 302 • • Do not get too close to the vehicle you want to Check your mirrors, glance over your shoulder and pass while you’re awaiting an opportunity. For start your left lane change signal before moving out one thing, following too closely reduces your area of the right lane to pass.
Page 303: Loss Of Control
Loss of Control If you have the Traction Assist System, remember: It helps avoid only the acceleration skid. If you do not have this system, or if the system is off, then an acceleration Let’s review what driving experts say about what skid is also best handled by easing your foot off the happens when the three control systems (brakes, accelerator pedal.
Page 304: Off-Road Driving With Your Four-Wheel-Drive Vehicle
Off-Road Driving with Your Four-Wheel-Drive Vehicle This off-road guide is for vehicles that have four-wheel drive. Also, see Braking on page 4-6 . If your vehicle doesn’t have four-wheel drive, you shouldn’t drive off-road unless you’re on a level, solid surface. Off-road driving can be great fun.
Page 305 1. Insert a tool into the 3. Pull the push-pins and push-pin slot and pull lower dam assembly downward until the away from the retainers push-pin snaps loose. until the lower dam is free. When you’re back on roads, though, be sure to replace 2.
Page 306: Before You Go Off-Roading
Before You Go Off-Roading To reinstall the lower air dam, do the following: 1. Line up each push-pin There are some things to do before you go out. For with its intended example, be sure to have all necessary maintenance retainer and push the and service work done.
Page 307: Environmental Concerns
Environmental Concerns CAUTION: Off-road driving can provide wholesome and satisfying recreation. However, it also raises environmental concerns. GM recognizes these concerns and urge • Cargo on the load ﬂoor piled higher than every off-roader to follow these basic rules for protecting the seatbacks can be thrown forward the environment: during a sudden stop.
Page 308: Traveling To Remote Areas
Traveling to Remote Areas Controlling your vehicle is the key to successful off-road driving. One of the best ways to control your vehicle It makes sense to plan your trip, especially when going is to control your speed. Here are some things to keep to a remote area.
Page 309: Scanning The Terrain
Scanning the Terrain When you drive over obstacles or rough terrain, keep a ﬁrm grip on the steering wheel. Ruts, troughs or Off-road driving can take you over many different kinds other surface features can jerk the wheel out of your of terrain.
Page 310: Driving On Off-Road Hills
Driving on Off-Road Hills Approaching a Hill Off-road driving often takes you up, down or across a When you approach a hill, you need to decide if it’s one of hill. Driving safely on hills requires good judgment those hills that’s just too steep to climb, descend or cross. and an understanding of what your vehicle can and can’t Steepness can be hard to judge.
Page 311: Driving Uphill
Driving Uphill CAUTION: Once you decide you can safely drive up the hill, you need to take some special steps. • Use a low gear and get a ﬁrm grip on the steering Turning or driving across steep hills can be wheel.
Page 312 • Ease up on your speed as you approach the top of What should I do if my vehicle stalls, or is the hill. about to stall, and I can’t make it up the hill? • Attach a ﬂag to the vehicle to make you more If this happens, there are some things you should visible to approaching traffic on trails or hills.
Page 313 • Instead, apply the regular brake to stop the vehicle. As you are backing down the hill, put your left hand Then apply the parking brake. Shift to on the steering wheel at the 12 o’clock position. REVERSE (R), release the parking brake, and This way, you’ll be able to tell if your wheels slowly back straight down.
Page 314: Driving Downhill
Suppose, after stalling, I try to back down the hill CAUTION: (Continued) and decide I just can’t do it. What should I do? Set the parking brake, put your transmission in transmission. You or someone else could be PARK (P), or the manual transmission in injured.
Page 315 • If you decide you can go down a hill safely, then try to When driving downhill, avoid turns that take you keep your vehicle headed straight down, and use a across the incline of the hill. A hill that’s not too low gear.
Page 316: Driving Across An Incline
Driving Across an Incline For reasons like these, you need to decide carefully whether to try to drive across an incline. Just because Sooner or later, an off-road trail will probably go across the trail goes across the incline doesn’t mean you the incline of a hill.
Page 317: Stalling On An Incline
Stalling on an Incline CAUTION: If your vehicle stalls when you’re crossing an incline, be sure you (and your passengers) get out on the uphill side, even if the door there is harder to open. If you get Getting out on the downhill (low) side of a out on the downhill side and the vehicle starts to roll vehicle stopped across an incline is over, you’ll be right in its path.
Page 318: Driving In Mud, Sand, Snow Or Ice
Driving in Mud, Sand, Snow or Ice Hard packed snow and ice offer the worst tire traction. On these surfaces, it’s very easy to lose control. On When you drive in mud, snow or sand, your wheels wet ice, for example, the traction is so poor that you will won’t get good traction.
Page 319: Maintenance Schedule
Driving in Water CAUTION: (Continued) Heavy rain can mean ﬂash ﬂooding, and ﬂood waters demand extreme caution. still wash away the ground from under your Find out how deep the water is before you drive through tires, and you could lose traction and roll the it.
Page 320: Driving At Night
Driving at Night Here are some tips on night driving. • Drive defensively. • Don’t drink and drive. • Adjust your inside rearview mirror to reduce the glare from headlamps behind you. • Since you can’t see as well, you may need to slow down and keep more space between you and other vehicles.
Page 321: Driving In Rain And On Wet Roads
Driving in Rain and on Wet Roads You can be temporarily blinded by approaching headlamps. It can take a second or two, or even several seconds, for your eyes to re-adjust to the dark. When you are faced with severe glare (as from a driver who doesn’t lower the high beams, or a vehicle with misaimed headlamps), slow down a little.
Page 322 The heavier the rain, the harder it is to see. Even if your Driving too fast through large water puddles or even windshield wiper blades are in good shape, a heavy going through some car washes can cause problems, rain can make it harder to see road signs and too.
Page 323: Driving Through Deep Standing Water
Hydroplaning Driving Through Deep Standing Water Hydroplaning is dangerous. So much water can build up Notice: If you drive too quickly through deep under your tires that they can actually ride on the puddles or standing water, water can come in water.
Page 324: Some Other Rainy Weather Tips
Some Other Rainy Weather Tips City Driving • Turn on your low-beam headlamps – not just your parking lamps – to help make you more visible to others. • Besides slowing down, allow some extra following distance. And be especially careful when you pass another vehicle.
Page 325: Freeway Driving
Freeway Driving Here are ways to increase your safety in city driving: • Know the best way to get to where you are going. Get a city map and plan your trip into an unknown part of the city just as you would for a cross-country trip.
Page 326: Before Leaving On A Long Trip
At the entrance, there is usually a ramp that leads to the The exit ramp can be curved, sometimes quite sharply. freeway. If you have a clear view of the freeway as you The exit speed is usually posted. drive along the entrance ramp, you should begin to check Reduce your speed according to your speedometer, not traffic.
Page 327: Highway Hypnosis
Highway Hypnosis Here are some things you can check before a trip: • Windshield Washer Fluid: Is the reservoir full? Are Is there actually such a condition as “highway all windows clean inside and outside? hypnosis”? Or is it just plain falling asleep at the wheel? •...
Page 328: Hill And Mountain Roads
Hill and Mountain Roads • Keep your vehicle in good shape. Check all ﬂuid levels and also the brakes, tires, cooling system and transmission. These parts can work hard on mountain roads. • Know how to go down hills. The most important thing to know is this: let your engine do some of the slowing down.
Page 329 • Know how to go uphill. You may want to shift down to a lower gear. The lower gears help cool your CAUTION: engine and transmission, and you can climb the hill better. Coasting downhill in NEUTRAL (N) or with the •...
Page 330: Winter Driving
Winter Driving Here are some tips for winter driving: • Have your vehicle in good shape for winter. • You may want to put winter emergency supplies in your vehicle. Include an ice scraper, a small brush or broom, a supply of windshield washer ﬂuid, a rag, some winter outer clothing, a small shovel, a ﬂashlight, a red cloth and reﬂective warning triangles.
Page 331: Driving On Snow Or Ice
Driving on Snow or Ice What’s the worst time for this? “Wet ice.” Very cold snow or ice can be slick and hard to drive on. But wet Most of the time, those places where your tires meet ice can be even more trouble because it may offer the road probably have good traction.
Page 332: If You're Caught In A Blizzard
If You’re Caught in a Blizzard Your anti-lock brakes improve your vehicle’s stability when you make a hard stop on a slippery road. Even though you have an anti-lock braking system, you’ll want to begin stopping sooner than you would on dry pavement.
Page 333 • Put on extra clothing or wrap a blanket around you. If you have no blankets or extra clothing, make CAUTION: body insulators from newspapers, burlap bags, rags, ﬂoor mats – anything you can wrap around yourself or tuck under your clothing to keep warm. Snow can trap exhaust gases under your vehicle.
Page 334: If You Are Stuck: In Sand, Mud, Ice Or Snow
Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine CAUTION: again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible.
Page 335: Using The Recovery Hooks
Rocking Your Vehicle To Get It Out Using the Recovery Hooks First, turn your steering wheel left and right. That will clear the area around your front wheels. If you have a four-wheel-drive vehicle, shift into 4HI. If your vehicle has the Traction Assist System, you should turn it off by pressing the TAS on/off button.
Page 336 CAUTION: These hooks, when used, are under a lot of force. Always pull the vehicle straight out. Never pull on the hooks at a sideways angle. The hooks could break off and you or others could be injured from the chain or cable snapping back.
Page 337: Towing
Towing Here are some important things to consider before you do recreational vehicle towing: • What’s the towing capacity of the towing vehicle? Towing Your Vehicle Be sure you read the tow vehicle manufacturer’s recommendations. Consult your dealer or a professional towing service if •...
Page 338 Four-Wheel-Drive Vehicles 4. Shift the transfer case to NEUTRAL. See Four-Wheel Drive on page 2-33 for the proper procedure to select the neutral position for your vehicle. 5. Release the parking brake only after the vehicle being towed is ﬁrmly attached to the towing vehicle.
Page 339: Dolly Towing
Dolly Towing Two-Wheel-Drive Vehicles CAUTION: Two-wheel-drive vehicles should not be towed with the rear wheels on the ground. Two-wheel-drive Shifting a four-wheel-drive vehicle’s transfer transmissions have no provisions for internal lubrication case into NEUTRAL can cause your vehicle to while being towed. To properly tow these vehicles, they roll even if the transmission is in Park (P) for should be placed on a platform trailer with all four wheels an automatic transmission, or if your vehicle is...
Page 340: Loading Your Vehicle
Loading Your Vehicle The Certiﬁcation/Tire label also tells you the maximum weights for the front and rear axles, called Gross Axle Weight Rating (GAWR). To ﬁnd out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle.
Page 341 CAUTION: CAUTION: Do not load your vehicle any heavier than the Things you put inside your vehicle can strike GVWR, or either the maximum front or rear and injure people in a sudden stop or turn, or GAWR. If you do, parts on your vehicle can in a crash.
Page 342: Add-On Equipment
Payload Remember not to exceed the Gross Axle Weight Rating (GAWR) of the front or rear axle. See Loading Your Payload capacity is the maximum load capacity that your Vehicle on page 4-58 . vehicle can carry. Be sure to include the weight of the Add-On Equipment occupants as part of your load.
Page 343: Adding A Snow Plow Or Similar Equipment
Adding a Snow Plow or Similar How heavy can a snow plow safely be? Equipment The plow your vehicle can carry depends on many things, such as: Before installing a snow plow on your vehicle, here are • some things you’ll need to know: The options your vehicle came with, and the weight of those options, Notice: If your vehicle does not have the snow...
Page 344 Here are some guidelines for safely carrying a snow What is front axle reserve capacity, and how do plow on your vehicle: I calculate it? • Make sure the weight on the front and rear axles Front axle reserve capacity is the difference doesn’t exceed the axle rating for each.
Page 345 In order to calculate the amount of weight any front (W x (A + W.B.)) /W.B.= Weight the accessory is adding accessory, such as a snow plow, is adding to the front to the front axle. axle, use the following formula: Where: W = Weight of added accessory A = Distance that the accessory is in front of the...
Page 346 What if I want to add heavier equipment to my vehicle? CAUTION: You can add heavier equipment on the front of the vehicle if you compensate for it by carrying fewer On some vehicles equipped with certain front passengers, less cargo, or by positioning cargo mounted equipment, such as a snow plow, it towards the rear.
Page 347: Truck-Camper Loading Information
Truck-Camper Loading Information What is total vehicle reserve capacity? This is the difference between your GVWR and Notice: If your vehicle is equipped with the SS trim the weight of your truck with full fuel and package, do not install a truck-camper or your passengers.
Page 348 Refer to the Truck-Camper Loading Information label in Here is an example of proper truck and camper match: glove box for dimensions A and B as shown in the following illustration. A. Camper Center of Gravity B. Recommended Center of Gravity Location Zone Use the rear edge of the load ﬂoor for measurement The camper’s center of gravity should fall within the purposes.
Page 349: Trailer Recommendations
Trailer Recommendations Your dealer can help you make a good vehicle-camper match and help you determine the CWR. You must subtract your hitch loads from the CWR for After you’ve loaded your vehicle and camper, drive to a your vehicle. Weigh your vehicle with the trailer weigh station and weigh the front and rear wheels attached, so that you won’t go over the GVWR or separately.
Page 350: Towing A Trailer
Towing a Trailer If yours was built with trailering options, as many are, it’s ready for heavier trailers. But trailering is different than just driving your vehicle by itself. Trailering means changes in handling, durability and fuel economy. CAUTION: Successful, safe trailering takes correct equipment, and it has to be used properly.
Page 351 • Tow/Haul Mode Consider using a sway control if your trailer will weigh less than 5,000 lbs. (2 270 kg) for light duty Tow/haul is a feature on automatic transmission vehicles, or less than 7,500 lbs. (3 405 kg) for heavy equipped vehicles that assists when pulling a heavy duty vehicles.
Page 352: Weight Of The Trailer
Weight of the Trailer Tow/haul is designed to be most effective when the vehicle and trailer combined weight is at least 75% of How heavy can a trailer safely be? the vehicle’s Gross Combined Weight Rating (GCWR). See Weight of the Trailer later in the section. Tow/haul It depends on how you plan to use your rig.
Page 353 Vehicle* Axle Ratio Maximum Trailer Weight GCWR C-1500 Regular Cab Short Box (2WD)* 3.08 4,500 lbs. (2 041kg) 9,000 lbs. (4 086 kg) 4300 V6 (Auto) 3.42 5,000 lbs. (2 267kg) 9,500 lbs. (4 313 kg) 3.08 3,500 lbs. (1 587 kg) 8,000 lbs.
Page 354 Vehicle* Axle Ratio Maximum Trailer Weight GCWR 3.73 7,600 lbs. (3 447 kg)*** 13 000 lbs. (5 896 kg) 5300 V8 w/4WS 4.10 8,600 lbs. (3 900 kg)*** 14 000 lbs. (6 350 kg) * Tongue weight should be 10 percent to 15 percent of trailer weight up to 1,000 lbs (454 kg). Fifth-wheel or gooseneck kingpin weight 15 percent to 25 percent of trailer weight up to 1,500 lbs.
Page 355 Vehicle* Axle Ratio Maximum Trailer Weight GCWR C–1500 Regular Cab Long Box (2WD)* 3.08 4,400 lbs. (1 995 kg) 9,000 lbs. (4 086 kg) 4300 V6 (Auto) 3.42 4,900 lbs. (2 222 kg) 9,500 lbs. (4 313 kg) 3.08 3,400 lbs. (1 542 kg) 8,000 lbs.
Page 356 Vehicle* Axle Ratio Maximum Trailer Weight GCWR K-1500 Regular Cab Short Box (4WD)* 3.42 4,700 lbs. (2 131 kg) 9,500 lbs. (4 313 kg) 4300 V6 (Auto) 3.73 5,200 lbs. (2 358 kg) 10,000 lbs. (4 540 kg) 3.42 3,700 lbs. (1 678 kg) 8,500 lbs.
Page 357 Vehicle* Axle Ratio Maximum Trailer Weight GCWR K-1500 Crew Cab Short Box (4WD)* 3.73 7,900 lbs. (3 583 kg) 14,000 lbs. (6 356 kg) 6000 V8 4.10 9,900 lbs. (4 490 kg) 16,000 lbs. (7 264 kg) 3.73 7,600 lbs. (3 447 kg) 14,000 lbs.
Page 358 Vehicle* Axle Ratio Maximum Trailer Weight GCWR 3.73 5,000 lbs. (2 267 kg) 10,000 lbs. (4 540 kg) 4800 V8 (Manual) 4.10 6,000 lbs. (2 721 kg) 11,000 lbs. (4 994 kg) 3.73 8,000 lbs. (3 628 kg) 13,000 lbs. (5 902 kg) 5300 V8 4.10 9,000 lbs.
Page 359 Vehicle Axle Ratio Maximum Trailer Weight GCWR Silverado SS 6000 V8 Please see your dealer for maximum trailer weight and GCWR. Vehicle* Axle Ratio Maximum Trailer Weight GCWR C-2500 LD (2WD** 3.73 8,700 lbs. (3 946 kg) 14,000 lbs. (6 356 kg) 6000 V8 4.10 10,700 lbs.
Page 360 Vehicle* Axle Ratio Maximum Trailer Weight GCWR C-2500 Extended Cab Short Box HD (2WD)* 6000 V8 4.10 10,300 lbs. (4 676 kg) 16,000 lbs. (7 264 kg) 3.73 13,800 lbs. (6 259 kg)** 20,000 lbs. (9 080 kg) 8100 V8 4.10 15,800 lbs.
Page 361 Vehicle* Axle Ratio Maximum Trailer Weight GCWR C-2500 Crew Cab Long Box HD (2WD) 6000 V8 4.10 9,900 lbs. (4 490 kg) 16,000 lbs. (7 264 kg) 3.73 13,500 lbs. (6 123 kg)** 20,000 lbs. (9 080 kg) 8100 V8 4.10 15,500 lbs.
Page 362 Vehicle* Axle Ratio Maximum Trailer Weight GCWR K-2500 Regular Cab Long Box HD (4WD)* 6000 V8 4.10 10,300 lbs. (4 672 kg) 16,000 lbs. (7 264 kg) 3.73 13,800 lbs. (6 259 kg)** 20,000 lbs. (9 080 kg) 8100 V8 4.10 15,800 lbs.
Page 363 Vehicle* Axle Ratio Maximum Trailer Weight GCWR K-2500 Extended Cab Long Box HD (4WD)** 6000 V8 4.10 9,900 lbs. (4 494 kg) 16,000 lbs. (7 264 kg) 3.73 13,400 lbs. (6 078 kg)** 20,000 lbs. (9 080 kg) 8100 V8 4.10 15,400 lbs.
Page 364 Vehicle* Axle Ratio Maximum Trailer Weight GCWR C-3500 Extended Cab (2WD) 6000 V8 4.10 9,800 lbs. (4 449 kg) 16,000 lbs. (7 264 kg) 8100 V8 4.10 15,400 lbs. (6 985 kg)** 22,000 lbs. (9 988 kg) 6.6L V8 Diesel 3.73 15,200 lbs.
Page 365 Vehicle* Axle Ratio Maximum Trailer Weight GCWR K-3500 Crew Cab (4WD)* 6000 V8 4.10 9,200 lbs. (4 173 kg) 16,000 lbs. (7 264 kg) 8100 V8 4.10 14,800 lbs. (6 713 kg)** 22,000 lbs. (9 988 kg) 6.6L V8 Diesel 3.73 14,700 lbs.
Page 366: Weight Of The Trailer Tongue
Weight of the Trailer Tongue If you’re using a weight-carrying or a weight-distributing hitch, the trailer tongue weight (A) should be 10 The tongue load (A) of any trailer is an important weight percent to 15 percent of the total loaded trailer to measure because it affects the total or gross weight weight (B).
Page 367: Trailer Brakes
Hitches chains to the attaching point on the hitch platform. If you are towing with an aftermarket hitch follow the trailer It’s important to have the correct hitch equipment. or hitch manufacturer’s recommendation for attaching Crosswinds, large trucks going by and rough roads are safety chains.
Page 368: Driving With A Trailer
Driving with a Trailer Following Distance Towing a trailer requires a certain amount of experience. Stay at least twice as far behind the vehicle ahead as you Before setting out for the open road, you’ll want to get would when driving your vehicle without a trailer. This can to know your rig.
Page 369: Turn Signals When Towing A Trailer
Turn Signals When Towing a Trailer If you have a 5-speed manual transmission and you are towing a trailer, it’s better not to use FIFTH (5) gear. The arrows on your instrument panel will ﬂash whenever Just drive in FOURTH (4) gear (or, as you need you signal a turn or lane change.
Page 370: Parking On Hills
Parking on Hills 5. If you have a four-wheel-drive vehicle, be sure the transfer case is in a drive gear and not in NEUTRAL. CAUTION: 6. Release the regular brakes. You really should not park your vehicle, with a CAUTION: trailer attached, on a hill.
Page 371: Trailer Wiring Harness
When You Are Ready to Leave After Trailer Wiring Harness Parking on a Hill Your vehicle is equipped with one of the following wiring harnesses for towing a trailer or hauling a slide-in 1. Apply your regular brakes and hold the pedal down camper.
Page 372: Heavy-Dutytrailer Wiring Harness Package
Heavy-DutyTrailer Wiring Harness The six-wire harness contains the following trailer circuits: Package • Yellow: Left Stop/Turn Signal • Dark Green: Right Stop/Turn Signal • Brown: Taillamps • White: Ground • Light Green: Back-up Lamps • Light Blue: Center High-Mounted Stoplamp (CHMSL) If you need to upgrade your trailer wiring harness, an additional 2–wire harness and 7 pin universal trailer...
Page 373 Camper/Fifth-Wheel Trailer Wiring Package The eight-wire harness contains the following trailer circuits: The eight-wire camper harness is located under the • Yellow: Left Stop/Turn Signal front edge of the pickup box on the driver’s side of the vehicle, attached to the frame bracket. A connector •...
Page 374 Instrument Panel Jumper Wiring Harness If your vehicle is equipped with the “Heavy-Duty Trailering″ option, please refer to Heavy-Duty Trailer This harness may be included with your vehicle as part Wiring Package , earlier in this section. of the heavy-duty trailer wiring package. When the camper-wiring harness is ordered without the This harness is for an electric brake controller and heavy-duty trailering package, an eight-wire harness...
Page 375 Four-Wire Harness Adapter This adapter may be included with your vehicle as part of the heavy-duty trailer wiring package. Connect the adapter with the tab pointing up (see Use this adapter to connect a standard four-way round arrow). The ﬂip cap on the vehicle’s seven-wire harness pin connector to the seven-wire harness on your will lock onto the tab and help hold the adapter in vehicle.
Page 376: Power Winches
Auxiliary Battery When using this provision, connection should only be made to the upper stud (A) of the relay. Do not The auxiliary battery provision can be used to supply make connections to the lower stud (B) of the relay. electrical power to additional equipment that you The auxiliary battery circuit is protected by a megafuse may choose to add, such as a slide-in camper.
Page 377: Power Take-Off (Pto)
Power Take-Off (PTO) To engage a PTO on a vehicle with an automatic transmission do the following: Before using a PTO, if equipped, refer to the 1. For stationary use shift the transmission into manufacturer’s or installer’s instructions. PARK (P). To engage a PTO on a vehicle with a manual 2.
Page 378 Preset Mode: PTO speed control mode is used for To use PTO speed control in variable mode (while stationary applications. (PTO will remain engaged while stationary) do the following: mobile in the preset mode, however PTO set and 1. Engage the PTO. resume speed controls will be inoperative).
Page 379: Step-Bumper Pad
Step-Bumper Pad All engine speed values listed above are factory preset values. With the exception of the TCC lockup speed Your vehicle has a rear step bumper with a rear step (1,100 rpm) and the “tap″ increment (100 rpm), all pad at the center of the bumper.
Page 380 NOTES 4-98...
Page 381: Service And Appearance Care
Section 5 Service and Appearance Care Service ............5-3 Automatic Transmission Fluid (Allison ® Doing Your Own Service Work ......5-3 Transmission ) ..........5-26 Adding Equipment to the Outside of Your Manual Transmission Fluid ......5-28 Vehicle ............5-4 Hydraulic Clutch ...........5-29 Engine Coolant ..........5-30 Fuel ..............5-4 Coolant Surge Tank Pressure Cap ....5-33 Gasoline Octane ..........5-4...
Page 382 Section 5 Service and Appearance Care Bulb Replacement ..........5-59 Appearance Care ..........5-100 Halogen Bulbs ..........5-59 Cleaning the Inside of Your Vehicle ....5-100 Headlamps ..........5-59 Care of Safety Belts ........5-103 Front Turn Signal, Sidemarker and Daytime Weatherstrips ..........5-103 Running Lamps .........5-61 Cleaning the Outside of Your Vehicle .....5-103 Roof Marker Lamps ........5-62 Sheet Metal Damage ........5-105...
Page 383: Service
Service Doing Your Own Service Work If you want to do some of your own service work, you’ll Your dealer knows your vehicle best and wants you to want to use the proper service manual. It tells you be happy with it. We hope you will go to your dealer much more about how to service your vehicle than this for all your service needs.
Page 384: Adding Equipment To The Outside Of Your
Gasoline Octane CAUTION: (Continued) For all except the Silverado SS model, use regular unleaded gasoline with a posted octane of 87 or higher. • Be sure to use the proper nuts, bolts and If the octane is less than 87, you may get a heavy other fasteners.
Page 385: Gasoline Speciﬁcations
Gasoline Speciﬁcations California Fuel It is recommended that gasoline meet speciﬁcations If your vehicle is certiﬁed to meet California Emission which were developed by the American Automobile Standards (see the underhood emission control label), it Manufacturers Association and endorsed by the is designed to operate on fuels that meet California Canadian Vehicle Manufacturers Association for better speciﬁcations.
Page 386: Fuels In Foreign Countries
Notice: Your vehicle was not designed for fuel that Filling Your Tank contains methanol. Do not use fuel containing methanol. It can corrode metal parts in your fuel system and also damage the plastic and rubber CAUTION: parts. That damage would not be covered under your warranty.
Page 387 CAUTION: (Continued) quickly. This spray can happen if your tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any “hiss” noise to stop. Then unscrew the cap all the way. Be careful not to spill gasoline.
Page 388: Filling A Portable Fuel Container
Filling a Portable Fuel Container Checking Things Under the Hood CAUTION: CAUTION: Never ﬁll a portable fuel container while it is in your vehicle. Static electricity discharge from Things that burn can get on hot engine parts the container can ignite the gasoline vapor. and start a ﬁre.
Page 389: Hood Release
Hood Release To open the hood do the following: 1. Pull the handle inside the vehicle located under and to the left of the steering wheel. 2. Then go to the front of the vehicle and pull up on the secondary hood release located near the center of the grill.
Page 390: Engine Compartment Overview
Engine Compartment Overview When you lift up the hood on the VORTEC™ 4300 V6 engine, you’ll see the following: 5-10...
Page 391: Engine Air Cleaner/Filter
A. Engine Air Cleaner/Filter. See Engine Air H. Power Steering Fluid Reservoir. See Power Steering Cleaner/Filter on page 5-21 . Fluid on page 5-42 . B. Coolant Surge Tank. See Engine Coolant on I. Remote Negative (−) Terminal (GND). See Jump page 5-30 .
Page 392 When you lift up the hood on the VORTEC™ 5300 V8 engine (VORTEC™ 4800 and 6000 V8 engines similar), you will see the following: 5-12...
Page 393: Transmission
A. Engine Air Cleaner/Filter. See Engine Air H. Remote Negative (−) Terminal (GND). See Jump Cleaner/Filter on page 5-21 . Starting on page 5-48 . B. Coolant Surge Tank. See Engine Coolant on I. Power Steering Fluid Reservoir. See Power Steering page 5-30 .
Page 394 When you lift up the hood on the VORTEC™ 8100 V8 engine you will see the following: 5-14...
Page 395 A. Engine Air Cleaner/Filter. See Engine Air H. Remote Negative (−) Terminal (GND). See Jump Cleaner/Filter on page 5-21 . Starting on page 5-48 . B. Coolant Surge Tank. See Engine Coolant on I. Remote Positive (+) Terminal. See Jump Starting on page 5-30 .
Page 396: Checking Engine Oil
Engine Oil The engine oil dipstick has a yellow ring handle and is located in the engine If your vehicle has a diesel engine, see “Engine Oil” in compartment on the the Diesel Engine Supplement. passenger’s side of the If the CHECK OIL LEVEL light appears on the vehicle.
Page 397: When To Add Engine Oil
The engine oil ﬁll cap for the VORTEC™ 4800, 5300 and 6000 V8 engines is located on the engine valve cover on the passenger’s side of the vehicle. On the 8100 engine, the oil ﬁll cap is 8.1L Engine located on the front of the engine.
Page 398: What Kind Of Engine Oil To Use
What Kind of Engine Oil to Use Oils recommended for your vehicle can be identiﬁed by looking for the starburst symbol. This symbol indicates that the oil has been certiﬁed by the American Petroleum Institute (API). Do not use any oil which does not carry this starburst symbol. If you choose to perform the engine oil change service yourself, be sure...
Page 399: Engine Oil Additives
When to Change Engine Oil As in the chart shown previously, SAE 5W-30 is the only viscosity grade recommended for your vehicle. You (GM Oil Life System) should look for and use only oils which have the API Starburst symbol and which are also identiﬁed as Your vehicle has a computer system that lets you know SAE 5W-30.
Page 400: What To Do With Used Oil
How to Reset the CHANGE ENGINE OIL What to Do with Used Oil Message System Used engine oil contains certain elements that may be The GM Oil Life System calculates when to change unhealthy for your skin and could even cause cancer. your engine oil and ﬁlter based on vehicle use.
Page 401: When To Inspect
Engine Air Cleaner/Filter How to Inspect Locate the ﬁlter change indicator. When the change See Engine Compartment indicator turns black or is in the red/orange “change” Overview on page 5-10 for zone, replace the ﬁlter and reset the indicator. To location of engine air inspect the air cleaner/ﬁlter, remove the ﬁlter from the cleaner/ﬁlter and change...
Page 402 CAUTION: Operating the engine with the air cleaner/ﬁlter off can cause you or others to be burned. The air cleaner not only cleans the air, it helps to stop ﬂame if the engine backﬁres. If it is not there and the engine backﬁres, you could be burned.
Page 403: How To Check
Automatic Transmission Fluid How to Check ® (Except Allison Transmission Because this operation can be a little difficult, you may choose to have this done at the dealership service When to Check and Change department. If you do it yourself, be sure to follow all the instructions A good time to check your automatic transmission ﬂuid here, or you could get a false reading on the dipstick.
Page 404: Checking The Fluid Level
Get the vehicle warmed up by driving about 15 miles Then, without shutting off the engine, follow these steps: (24 km) when outside temperatures are above 50°F The transmission dipstick (10°C). If it’s colder than 50°F (10°C), drive the vehicle handle with the graphic is in THIRD (3) until the engine temperature gage located at the rear of...
Page 405: How To Add Fluid
How to Add Fluid Refer to the Maintenance Schedule to determine what kind of transmission ﬂuid to use. See Part D: Recommended Fluids and Lubricants on page 6-19 . Add ﬂuid only after checking the transmission ﬂuid while it is hot. (A cold check is used only as a reference.) If the ﬂuid level is low, add only enough of the proper ﬂuid to bring the level up to the HOT area for a hot check.
Page 406 Automatic Transmission Fluid If you do it yourself, be sure to follow all the instructions here, or you could get a false reading on the dipstick. ® (Allison Transmission Notice: Too much or too little ﬂuid can damage When to Check and Change your transmission.
Page 407 • 5. Perform a hot check at the ﬁrst opportunity after the With your foot on the brake pedal, run the engine for normal operating temperature of 160°F (71°C) to at least once minute and shift to DRIVE (D). Then 200°F (93°C) is reached.
Page 408: Manual Transmission Fluid
Consistency of Readings Manual Transmission Fluid Always check the ﬂuid level at least twice using the When to Check procedures described previously. Consistency (repeatable readings) is important to maintaining proper A good time to have it checked is when the engine oil is ﬂuid level.
Page 409: Hydraulic Clutch
How to Add Fluid Then, follow these steps: Here’s how to add ﬂuid. Refer to the Maintenance Schedule to determine what kind of ﬂuid to use. See Part D: Recommended Fluids and Lubricants on page 6-19 . 1. Remove the ﬁller plug. 2.
Page 410: Engine Coolant
When to Check and What to Use How to Check and Add Fluid The proper ﬂuid should be added if the level does not The clutch master cylinder reach the bottom of the diaphragm when it’s in place in reservoir is located in the the reservoir.
Page 411: What To Use
Notice: When adding coolant, it is important that ® you use only DEX-COOL (silicate-free) coolant. CAUTION: ® If coolant other than DEX-COOL is added to the system, premature engine, heater core or radiator corrosion may result. In addition, the engine Adding only plain water to your cooling coolant will require change sooner -- at 30,000 miles system can be dangerous.
Page 412: Adding Coolant
Checking Coolant The vehicle must be on a level surface. When your engine is cold, the coolant level should be at the FULL COLD mark. The coolant surge tank is located in the engine If your vehicle is equipped with a low coolant sensor, compartment on the and the LOW COOLANT LEVEL message comes passenger’s side of the...
Page 413: Coolant Surge Tank Pressure Cap
Coolant Surge Tank Pressure Cap Engine Overheating You will ﬁnd a coolant temperature gage on your See Engine Compartment vehicle’s instrument panel. See Engine Coolant Overview on page 5-10 for Temperature Gage on page 3-47 . In addition, you will more information on ﬁnd a LOW COOLANT LEVEL, ENGINE OVERHEATED location.
Page 414: If Steam Is Coming From Your Engine
If Steam Is Coming From Your Engine CAUTION: (Continued) everyone away from the vehicle until it cools down. Wait until there is no sign of steam or coolant before you open the hood. If you keep driving when your engine is overheated, the liquids in it can catch ﬁre.
Page 415: If No Steam Is Coming From Your Engine
If No Steam Is Coming From Your 3. If you’re in a traffic jam, shift to NEUTRAL (N); otherwise, shift to the highest gear while Engine driving – AUTOMATIC OVERDRIVE An overheat warning, along with a low coolant condition, DRIVE (D) for automatic transmissions. can indicate a serious problem.
Page 416: Cooling System
Cooling System When you decide it’s safe to lift the hood, here’s what you’ll see: All Other Engines A. Coolant Surge Tank B. Coolant Surge Tank Pressure Cap C. Engine Fan 8100 V8 Engines If the coolant inside the coolant surge tank is boiling, don’t do anything else until it cools down.
Page 417 The coolant level should If there seems to be no leak, start the engine again. be at or above the FULL The engine cooling fan speed should increase when idle COLD mark. If it isn’t, speed is doubled by pushing the accelerator pedal you may have a leak at the down.
Page 418 How to Add Coolant to the Coolant Surge Tank Gasoline Engines If you haven’t found a problem yet, check to see if coolant is visible in the surge tank. If coolant is visible but the coolant level isn’t at or above the FULL COLD mark, add a 50/50 mixture of clean, drinkable water and ®...
Page 419 1. Park the vehicle on a level surface. You can CAUTION: (Continued) remove the coolant surge tank pressure proper coolant mixture. With plain water or the cap when the cooling wrong mixture, your engine could get too hot system, including but you wouldn’t get the overheat warning.
Page 420 4. Then ﬁll the coolant surge tank with the proper 5. With the coolant surge tank pressure cap off, start mixture, to the FULL COLD mark. the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fan.
Page 421: Engine Fan Noise
Engine Fan Noise 6. Then replace the pressure cap. Be sure the pressure cap is Your vehicle has a clutched engine cooling fan. When hand-tight and the clutch is engaged, the fan spins faster to provide fully seated. more air to cool the engine. In most everyday driving conditions, the fan is spinning slower and the clutch is not fully engaged.
Page 422: Power Steering Fluid
Power Steering Fluid All Other Engines When to Check Power Steering Fluid 8100 V8 Engine It is not necessary to regularly check power steering ﬂuid unless you suspect there is a leak in the system or you hear an unusual noise. A ﬂuid loss in this system could indicate a problem.
Page 423: Windshield Washer Fluid
How to Check Power Steering Fluid Windshield Washer Fluid Turn the key off, let the engine compartment cool down, What to Use wipe the cap and the top of the reservoir clean, then unscrew the cap and wipe the dipstick with a clean rag. When you need windshield washer ﬂuid, be sure to read Replace the cap and completely tighten it.
Page 424: Brakes
Notice: Brakes • When using concentrated washer ﬂuid, follow Brake Fluid the manufacturer’s instructions for adding water. Your brake master cylinder reservoir is ﬁlled with DOT-3 • Don’t mix water with ready-to-use washer ﬂuid. brake ﬂuid. See Engine Compartment Overview on Water can cause the solution to freeze and page 5-10 for the location of the reservoir.
Page 425: Checking Brake Fluid
Checking Brake Fluid CAUTION: You can check the brake ﬂuid without taking off the cap. If you have too much brake ﬂuid, it can spill on the engine. The ﬂuid will burn if the engine is hot enough. You or others could be burned, and your vehicle could be damaged.
Page 426: What To Add
What to Add • If you spill brake ﬂuid on your vehicle’s painted surfaces, the paint ﬁnish can be damaged. Be When you do need brake ﬂuid, use only DOT-3 brake careful not to spill brake ﬂuid on your vehicle. If ﬂuid.
Page 427: Battery
Some driving conditions or climates may cause a brake system — for example, when your brake linings wear squeal when the brakes are ﬁrst applied or lightly down and you need new ones put in — be sure you get applied.
Page 428: Vehicle Storage
Vehicle Storage Jump Starting If you’re not going to drive your vehicle for 25 days or If your battery (or batteries) has run down, you may more, remove the black, negative (−) cable from want to use another vehicle and some jumper cables to the battery.
Page 429 Notice: If the other system isn’t a 12-volt system Notice: If you leave your radio on, it could be badly with a negative ground, both vehicles can be damaged. The repairs wouldn’t be covered by damaged. your warranty. 2. If you have a vehicle with a diesel engine with two 4.
Page 430 On V6 engines the remote negative (−) terminal is located on a tab attached to the engine accessory CAUTION: drive bracket where it is marked “GND.″ See Engine Compartment Overview on page 5-10 for more information on location. Fans or other moving engine parts can injure you badly.
Page 431 7. Connect the red 9. Now connect the black positive (+) cable to the negative (−) cable to positive (+) terminal the negative (−) of the vehicle with the terminal of the good dead battery. Use battery. Use a remote a remote positive (+) negative (−) terminal if terminal if the...
Page 432 11. Connect the other end of the negative (−) cable to the remote negative (−) terminal, marked GND, on the vehicle with the dead battery. 12. Now start the vehicle with the good battery and run the engine for a while. 13.
Page 433 To disconnect the jumper cables from both vehicles do the following: 1. Disconnect the black negative (−) cable from the vehicle that had the bad battery. 2. Disconnect the black negative (−) cable from the vehicle with the good battery. 3.
Page 434: All-Wheel Drive
All-Wheel Drive To get an accurate reading, the vehicle should be on a level surface. Lubricant checks in this section also apply to these If the level is below the bottom of the ﬁller plug hole, vehicles. However, there are two additional systems that you’ll need to add some lubricant.
Page 435: Rear Axle
Rear Axle The proper level for the 1500 Series is from 5/8 inch to 1 5/8 inch (15 mm to 40 mm) below the bottom of the ﬁller plug hole. The proper level for the 1500 HD When to Check Lubricant Series, 2500 Series, 2500 HD, and 3500 Series is from 0 to 1/2 inch (0 to 13 mm) below the bottom of the Refer to the Maintenance Schedule to determine how...
Page 436: Four-Wheel Drive
Four-Wheel Drive Lubricant checks in this section also apply to these vehicles. However, there are two additional systems that need lubrication. Transfer Case When to Check Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant. See Part C: Periodic Maintenance I nspections on page 6-17 .
Page 437: Front Axle
Front Axle If the level is below the bottom of the ﬁller plug hole, you may need to add some lubricant. When to Check Lubricant When the differential is cold, add enough lubricant to Refer to the Maintenance Schedule to determine how raise the level to 0 to 3/8 inch (9.5 mm) below the ﬁller often to check the lubricant.
Page 438: Noise Control System
Noise Control System 2. The use of the vehicle after such device or element of design has been removed or rendered inoperative by any person. Tampering with Noise Control Among those acts presumed to constitute tampering are the acts listed below. System Prohibited Insulation: The following information relates to compliance with...
Page 439: Bulb Replacement
Bulb Replacement Headlamps For any bulb changing procedure not listed in this section, contact your dealer. See Replacement Bulbs on page 5-67 for the proper types of bulbs to use. Halogen Bulbs CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured.
Page 440 A. Low-Beam Headlamp B. High-Beam Headlamp 2. Pull the headlamp assembly out. If your vehicle has one pin on the headlamp 3. Unplug the electrical connector. assembly, remove the pin. To remove the pin, turn the pin up and pull it out straight out. 4.
Page 441: Front Turn Signal, Sidemarker And Daytime Running Lamps
Front Turn Signal, Sidemarker and 1. Remove the headlamp assembly as mentioned previously. Daytime Running Lamps 2. Press the retainer clip, located behind the turn signal housing, towards the outside of the vehicle. 3. Pull the turn signal housing out from the vehicle. 4.
Page 442: Roof Marker Lamps
Roof Marker Lamps 1. Remove the two screws and lift off the lens. 2. Remove the six screws on the center roof marker lamps. 3. Turn the old bulb counterclockwise to remove it from the socket. 5-62...
Page 443: Center High-Mounted Stoplamp (Chmsl) And Cargo Lamp
Center High-Mounted Stoplamp 4. Put a new bulb into the socket and turn (CHMSL) and Cargo Lamp clockwise until it locks in place. 1. Remove the screws and lift off the lamp assembly. 5. Reinstall the lens and tighten the screws. 5-63...
Page 444 A. Cargo Lamps 4. If a CHMSL bulb is replaced, put the new bulb into the socket and press it in until it is tight. B. Center High-Mounted Stoplamps If a cargo lamp is replaced, put a new cargo lamp 2.
Page 445: Pickup Box Identiﬁcation And Fender Marker Lamps
Pickup Box Identiﬁcation and 3. Your vehicle may have one of the following Fender Marker Lamps taillamp assemblies: A. Stoplamp 1. Remove the screws and lamp assembly. B. Turn Signal 2. Unplug the lamp assembly harness. C. Back-up Lamp 3. Gently pry the individual lamp from the lamp housing.
Page 446 A. Stoplamp 4. Press the release tab, if equipped, and turn B. Turn Signal Lamp the bulb socket C. Back-up Lamp counterclockwise to D. Side Marker Lamp remove it from the taillamp housing. 5. Pull the old bulb straight out from the socket. 6.
Page 447: Replacement Bulbs
Taillamps (Chassis Cab Models) Replacement Bulbs Exterior Lamp Bulb Number Low-Beam Headlamps 9006 High-Beam Headlamp 9005 Daytime Running Lamps (DRL) 4114K Front Roof Marker Lamps Front Parking and Turn Lamp 3457A Rear Marker Lamp, Taillamp and 3157 Stop Lamp** Taillamp and Stop Lamp** 1157 Sidemarker Lamp (If Equipped) Rear Turn Lamp...
Page 448: Windshield Wiper Blade Replacement
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected at least twice a year for wear and cracking. See At Least Twice a Year on page 6-13 for more information. Replacement blades come in different types and are removed in different ways. For proper type and length, see Normal Maintenance Replacement Parts on page 5-121 .
Page 449: Tires
Overinﬂated tires are more likely to be cut, about your tire warranty and where to obtain service, punctured or broken by a sudden see your Chevrolet Warranty booklet for details. impact — such as when you hit a pothole. Keep tires at the recommended pressure.
Page 450: Dual Tire Operation
• Remove the valve cap from the tire valve stem. Press Tire overloading the tire gage ﬁrmly onto the valve to get a pressure • Bad wear measurement. If the cold tire inﬂation pressure is low, • add air until you reach the recommended amount. Bad handling •...
Page 451: Tire Inspection And Rotation
The purpose of regular rotation is to achieve more uniform wear for all tires on the vehicle. The ﬁrst rotation CAUTION: is the most important. See “Part A: Scheduled Maintenance Services,” in Section 6, for scheduled rotation intervals. If you operate your vehicle with a tire that is badly underinﬂated, the tire can overheat.
Page 452 If your vehicle has dual rear wheels and the tread design for the front tires is different from the dual rear tires, always use the correct rotation pattern shown here when rotating your tires. The dual tires are rotated as a pair, and the inside rear tires became the outside rear tires.
Page 453: When It Is Time For New Tires
When It Is Time for New Tires CAUTION: One way to tell when it’s time for new tires is to Rust or dirt on a wheel, or on the parts to check the treadwear which it is fastened, can make wheel nuts indicators, which will become loose after a time.
Page 454: Buying New Tires
Buying New Tires CAUTION: (Continued) To ﬁnd out what kind and size of tires you need, look at the Certiﬁcation/Tire label. have a crash. Using tires of different sizes may The tires installed on your vehicle when it was new had a also cause damage to your vehicle.
Page 455: Uniform Tire Quality Grading
Uniform Tire Quality Grading Treadwear The treadwear grade is a comparative rating based on Quality grades can be found where applicable on the the wear rate of the tire when tested under controlled tire sidewall between tread shoulder and maximum conditions on a speciﬁed government test course.
Page 456: Wheel Alignment And Tire Balance
Temperature – A, B, C Scheduled wheel alignment and wheel balancing are not needed. However, if you notice unusual tire wear or The temperature grades are A (the highest), B, and C, your vehicle pulling one way or the other, the alignment representing the tire’s resistance to the generation may need to be reset.
Page 457: Used Replacement Wheels
Whenever a wheel, wheel bolt or wheel nut is replaced on a dual wheel setup, check the wheel nut torque CAUTION: after 100, 1,000 and 6,000 miles (160, 1 600 and 10 000 km) of driving. For proper torque, see “Wheel Nut Torque”...
Page 458: Tire Chains
Tire Chains Notice: If your vehicle does not have dual wheels and is equipped with a tire size other than P265/75R16, LT65/75R16 or P275/55R20, use tire chains only where legal and only when you must. CAUTION: Use chains that are the proper size for your tires.
Page 459: If A Tire Goes Flat
If a Tire Goes Flat CAUTION: It’s unusual for a tire to “blowout” while you’re driving, especially if you maintain your tires properly. If air goes out of a tire, it’s much more likely to leak out slowly. Lifting a vehicle and getting under it to do But if you should ever have a “blowout,”...
Page 460: Changing A Flat Tire
Changing a Flat Tire If a tire goes ﬂat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning ﬂashers. CAUTION: Changing a tire can cause an injury. The vehicle can slip off the jack and roll over you or other people.
Page 461: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools ® Extended Cab Regular Cab and Crew Cab 5-81...
Page 462 1. If there is a cover, move the seats forward and turn the wing nut on the cover counterclockwise to ® remove it. For Crew Cab models, pull up the second row seat with the loop at the base of the seat cushion to access the tools.
Page 463 You’ll use the jack handle extensions and the wheel 1. If your vehicle is equipped with a hoist lock (J), wrench to remove the underbody-mounted spare tire. open the spare tire lock cover on the bumper and use the ignition key to remove the lock. 2.
Page 464 3. Insert the hoist end 5. The wheel wrench has (open end) (F) of the a hook that allows you extension through to pull the hoist the hole (G) in the rear cable towards you to bumper. assist in reaching the spare tire.
Page 465 Removing the Flat Tire and Installing the Spare Tire Use the following pictures and instructions to remove the ﬂat tire and raise the vehicle. 1. Remove the center cap by placing the chisel end of the wheel wrench in the slot on the wheel and gently prying the cap out.
Page 466 Jacking Locations A. Front Location (2-Wheel Drive 1500 Series) B. Front Location (All Other Series) C. Rear Location (All Series) 2. Use the wheel wrench to loosen all the wheel nuts. Turn the wheel wrench counterclockwise to loosen 3. Position the jack under the vehicle as shown. If the the wheel nuts.
Page 467 If you have added a snow plow to the front of your vehicle, lower the snow plow fully before raising the vehicle. CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack you could be badly injured or killed.
Page 468 Front Position All Other Models Rear Position 4. Make sure the jack head is positioned so that the rear axle is resting securely between the grooves that are on the jack head. Turn the wheel wrench clockwise to raise the vehicle. Raise the vehicle far enough off the ground so there is enough room for the spare tire to ﬁt under the wheel well.
Page 469 5. Remove all the wheel nuts and take off the CAUTION: ﬂat tire. Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after a time. The wheel could come off and cause an accident.
Page 470 7. After mounting the spare, put the wheel nuts back on with the rounded end of the nuts toward the wheel. Tighten each wheel nut by hand. Then use the wheel wrench to tighten the nuts until the wheel is held against the hub. Front Position All Models 5-90...
Page 471 Front Position 2WD 1500 Series Rear Position 8. Turn the wheel wrench counterclockwise to lower the vehicle. Lower the jack completely. 5-91...
Page 472 CAUTION: Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new GM original equipment wheel nuts.
Page 473 When you reinstall the regular wheel and tire, you must Return the bottle jack, wheel blocks, wheel wrench and also reinstall the center cap. Place the cap on the wheel jack extensions to their location behind the passenger’s and tap it into place until it seats ﬂush with the wheel. The seat.
Page 474 To store the jack and jack tools do the following: 1. Put the jack tools and gloves in the tool bag and place in the retaining bracket. Tighten down the wing nut. 2. Assemble the wheel blocks and bottle jack together with the wing nut and retaining hook.
Page 475 2. Tilt the retainer (D) 4. Insert the hoist end (F) downward and through through the hole (G) in the wheel opening. the rear bumper Make sure the retainer and into the hoist is fully seated across shaft. the underside of the wheel.
Page 476: Secondary Latch System
Secondary Latch System Your vehicle has an underbody mounted tire hoist assembly equipped with a secondary latch system. It’s designed to stop the spare tire from suddenly falling off your vehicle. For the secondary latch to work, the spare must be installed with the valve stem pointing down.
Page 477 To release the spare tire from the secondary latch do 4. Repeat this procedure at least two times. If the the following: spare tire lowers to the ground, continue with Step 5 of “Removing the Spare Tire and Tools” earlier in this section. 5.
Page 478 8. Attach the jack handle, extension, and wheel wrench to the jack and place it (with the wheel blocks) under the vehicle towards the front of the rear bumper. Position the center lift point of the jack under the center of the spare tire. 9.
Page 479 11. Lower the jack by turning the wheel wrench 13. Tilt the retainer at the counterclockwise. Keep lowering the jack until the end of the cable and spare tire slides off the jack or is hanging by pull it through the the cable.
Page 480: Appearance Care
Appearance Care Do not use any of these unless this manual says you can. In many uses, these will damage your vehicle: Remember, cleaning products can be hazardous. Some • Alcohol are toxic. Others can burst into ﬂames if you strike a •...
Page 481: Using Cleaner On Fabric
• 2. If a stain remains, follow the cleaning instructions Use a clean cloth or sponge, and change to a clean described earlier. area often. A soft brush may be used if stains are stubborn. 3. If an odor lingers after cleaning vomit or urine, treat the area with a water and baking soda solution: •...
Page 482: Cleaning Leather
Cleaning Leather Cleaning Interior Plastic Components Use a soft cloth with lukewarm water and a mild soap or Use only a mild soap and water solution on a soft cloth saddle soap and wipe dry with a soft cloth. Then, let or sponge.
Page 483: Care Of Safety Belts
Care of Safety Belts Cleaning the Outside of Your Vehicle Keep belts clean and dry. The paint ﬁnish on your vehicle provides beauty, depth of color, gloss retention and durability. CAUTION: Washing Your Vehicle Do not bleach or dye safety belts. If you do, it The best way to preserve your vehicle’s ﬁnish is to keep may severely weaken them.
Page 484: Cleaning Exterior Lamps/Lenses
Cleaning Exterior Lamps/Lenses Exterior painted surfaces are subject to aging, weather and chemical fallout that can take their toll over a Use only lukewarm or cold water, a soft cloth and a car period of years. You can help to keep the paint ﬁnish washing soap to clean exterior lamps and lenses.
Page 485: Cleaning Tires
Grime from the windshield will stick to the wiper blades Don’t take your vehicle through an automatic car wash and affect their performance. Clean the blade by that has silicone carbide tire cleaning brushes. These wiping vigorously with a cloth soaked in full-strength brushes can also damage the surface of these wheels.
Page 486: Finish Damage
Finish Damage At least every spring, ﬂush these materials from the underbody with plain water. Clean any areas where mud and debris can collect. Dirt packed in close areas of Any stone chips, fractures or deep scratches in the the frame should be loosened before being ﬂushed. ﬁnish should be repaired right away.
Page 487: Vehicle Care/Appearance Materials
Vehicle Care/Appearance Materials Vehicle Care/Appearance Materials (cont’d) See your GM dealer for more information on purchasing Description Usage the following products. Removes dirt and grime Chrome and Wire Wheel from chrome wheels and Vehicle Care/Appearance Materials Cleaner wire wheel covers. Description Usage Removes dust,...
Page 488: Vehicle Identiﬁcation
Vehicle Care/Appearance Materials Vehicle Identiﬁcation (cont’d) Description Usage Vehicle Identiﬁcation Number (VIN) Medium foaming shampoo. Cleans and Wash Wax Concentrate lightly waxes. Biodegradable and phosphate free. Quickly and easily removes spots and stains Spot Lifter from carpets, vinyl and cloth upholstery. This is the legal identiﬁer for your vehicle.
Page 489: Service Parts Identiﬁcation Label
Service Parts Identiﬁcation Label Your vehicle has an air bag system. Before attempting to add anything electrical to your vehicle, see Servicing Your Air Bag-Equipped Vehicle on page 1-80 . You’ll ﬁnd this label located in the glove box. It’s very helpful if you ever need to order parts.
Page 490: Fuses And Circuit Breakers
Fuses and Circuit Breakers Instrument Panel Fuse Block The wiring circuits in your vehicle are protected from The fuse block access short circuits by a combination of fuses, circuit breakers door is on the driver’s side and fusible thermal links. This greatly reduces the edge of the instrument chance of ﬁres caused by electrical problems.
Page 491 Fuses Usage HTR A/C Climate Control System Power Door Lock Relay LOCK (Relay) (Lock Function) HVAC 1 Climate Control System Driver’s Door Harness L DOOR Connection Cruise Control, Power Take CRUISE Off (PTO) Power Door Lock Relay UNLOCK (Relay) (Unlock Function) RR FOG LP Not Used BRAKE...
Page 492: Center Instrument Panel Fuse Block
Center Instrument Panel Fuse Block Fuses Usage Right Turn Signals and The center instrument panel utility block is located RT TRN Sidemarkers underneath the instrument panel, to the left of the BODY Harness Connector steering column. Driver Door Module AUX PWR 2 Not Used LOCKS Power Door Lock System...
Page 493: Underhood Fuse Block
The underhood fuse block in the engine compartment Device Usage on the driver’s side of the vehicle near the battery. Driver and Passenger Seat Lift the cover for access to the fuse/relay block. CB SEAT Module Circuit Breaker To remove fuses hold the end of the fuse between your Right Power Windows Circuit CB RT DOOR thumb and index ﬁnger and pull straight out.
Page 494 5-114...
Page 495 *1 — Gasoline Engine and Diesel Engine. Fuses Usage *2 — Gasoline Engine; ECMRPV — Diesel Engine. Accessory Power/Trailer STUD 2 Wiring Brake Feed *3 — Gasoline Engine; FUEL HT — Diesel Engine. Anti-Lock Brakes *4 — Gasoline Engine; ECM I — Diesel Engine. VSES/ECAS Vehicle Stability *5 —...
Page 496 Fuses Usage Fuses Usage SEO B2 Off-Road Lamps RR DEFOG Rear Window Defogger Vent Solenoid HDLP-HI Headlamp High Beam Relay Canister/Quadrasteer Module PRIME Not Used Power Oxygen Sensors RR HVAC Not Used Supplemental Inﬂatable Auxiliary Power Outlet — Restraint System AUX PWR Console Front Parking Lamps,...
Page 497 Fuses Usage Fuses Usage A/C COMP Air Conditioning Compressor FOG LP Fog Lamps Air Conditioning Compressor HORN Horn Relay A/C COMP Relay Windshield Washer Pump W/S WASH RR WPR Not Used Relay RADIO Audio System W/S WASH Windshield Washer Pump Mid Bussed Electrical Center, OnStar/Rear Seat INFO...
Page 498: Capacities And Speciﬁcations
Capacities and Speciﬁcations Please refer to Part D: Recommended Fluids and Lubricants on page 6-19 for more information. All capacities are approximate. When adding see the refrigerant charge label under the hood for charge capacity information and requirements. Capacities and Speciﬁcations Engine Type VIN Code...
Page 499 Capacities Application English Metric Cooling System After reﬁll, the level must be rechecked. See “Cooling System” in the Index. VORTEC™ 4300 V6 Automatic Transmission 12.6 quarts (11.9 L) VORTEC™ 4300 V6 Manual Transmission 12.9 quarts (12.2 L) VORTEC™ 4800 V8 Automatic Transmission 13.4 quarts (12.7 L) VORTEC™...
Page 500 Capacities Application English Metric VORTEC™ 6000 V8 (Vin N) 6.0 quarts (5.7 L) VORTEC™ 8100 V8 (Vin G) 6.5 quarts (6.1 L) Fuel Tank Short Bed 26.0 gallons (98 L) Short-Short Box Crew Cab 26.0 gallons (98 L) Long Bed 34.0 gallons 128 L Chassis Cab (pickup Box Delete)
Page 501: Normal Maintenance Replacement Parts
Normal Maintenance Replacement Parts VIN Code Oil Filter* PF47 PF44 PF44 Engine Air Cleaner /Filter* A1519C† A1519C† A1519C† PCV Valve* CV769C CV2001–C CV2001–C 41–974* 41–974* Spark Plugs 41–932* /PZTR5A15†† /PZTR5A15†† Fuel Filter* GF626 GF626 GF626 Wiper Blades** 15153642 15153642 15153642 Wiper Blade Type ITTA ITTA...
Page 502 VIN Code Oil Filter* PF44 PF44 PF454 Engine Air Cleaner /Filter* A1518C A1518C A1518C Passenger Compartment 52485513 52485513 52485513 Air Filter Kit** PCV Valve* CV2001–C CV2001–C — 41–974* 41–974* Spark Plugs PTJ14R15***†† /PZTR5A15†† /PZTR5A15†† Fuel Filter* GF626 GF626 GF626 Wiper Blades** 15153642 15153642 15153642...
Page 503 Section 6 Maintenance Schedule Maintenance Schedule ........6-2 Part C: Periodic Maintenance Inspections ..6-17 Introduction ...........6-2 Steering and Suspension Inspection ....6-17 Your Vehicle and the Environment ....6-2 Exhaust System Inspection ......6-17 Maintenance Requirements ......6-2 Fuel System Inspection ........6-17 How This Section is Organized ......6-3 Engine Cooling System Inspection ....6-17 Part A: Scheduled Maintenance Services ...6-4 Throttle System Inspection...
Page 504: Maintenance Schedule
Maintenance Schedule Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your Introduction vehicle in good working condition, but also helps the environment. Improper vehicle maintenance can Important: Keep engine oil at the proper level and even affect the quality of the air we breathe.
Page 505: How This Section Is Organized
How This Section is Organized If you want to get the service information, see Service Publications Ordering Information on page 7-9 . This maintenance schedule is divided into ﬁve parts: “Part B: Owner Checks and Services” tells you what should be checked and when. It also explains what “Part A: Scheduled Maintenance Services”...
Page 506: Part A: Scheduled Maintenance Services
Part A: Scheduled Maintenance This part tells you the maintenance services you should have done and when to schedule them. Services When you go to your dealer for your service needs, you’ll know that GM-trained and supported service This part contains engine oil and chassis lubrication people will perform the work using genuine GM parts.
Page 507: Scheduled Maintenance
Scheduled Maintenance Engine Oil and Chassis Lubrication Scheduled Maintenance The services shown in this schedule up to 100,000 miles (166 000 km) should be repeated after 100,000 miles Change engine oil and ﬁlter as indicated by the GM (166 000 km) at the same intervals for the life of Oil Life System (or every 12 months, whichever this vehicle.
Page 508 7,500 Miles (12 500 km) It is also important to check your oil regularly and keep it at the proper level. Check rear/front axle ﬂuid level and add ﬂuid as If the system is ever reset accidentally, you must needed. Check constant velocity joints and axle seals change your oil at 3,000 miles (5 000 km) since your for leaking.
Page 509 22,500 Miles (37 500 km) 30,000 Miles (50 000 km) Check rear/front axle ﬂuid level and add ﬂuid as Check rear/front axle ﬂuid level and add ﬂuid as needed. Check constant velocity joints and axle seals needed. Check constant velocity joints and axle seals for leaking.
Page 510 ® 45,000 Miles (75 000 km) Except Allison Transmission : If you do not use your vehicle under any of these conditions, change the ﬂuid Inspect engine air cleaner ﬁlter or change indicator (if and ﬁlter at 100,000 miles (166 000 km). equipped).
Page 511 75,000 Miles (125 000 km) Replace engine air cleaner ﬁlter on vehicles without a restriction indicator. If equipped with a change Inspect engine air cleaner ﬁlter or change indicator (if indicator, inspect the indicator. If necessary, replace equipped). If necessary, replace the ﬁlter. If vehicle is the ﬁlter.
Page 512 82,500 Miles (137 500 km) the ﬁlter. If vehicle is driven in dusty/dirty conditions, inspect the change indicator (if equipped) at every Check rear/front axle ﬂuid level and add ﬂuid as engine oil change. See Engine Air Cleaner/Filter needed. Check constant velocity joints and axle seals on page 5-21 for more information.
Page 513 100,000 Miles (166 000 km) Automatic Transfer Case Only: Change transfer case ﬂuid Inspect spark plug wires. An Emission Control Except 8.1L V8 Engine: Inspect Positive Crankcase Service. Ventilation (PCV) valve. An Emission Control Replace spark plugs. An Emission Control Service. Service.
Page 514: Engine Oil Level Check
Part B: Owner Checks and Services Engine Coolant Level Check ® Check the engine coolant level and add DEX-COOL Listed in this part are owner checks and services coolant mixture if necessary. See Engine Coolant which should be performed at the intervals speciﬁed to on page 5-30 for further details.
Page 515: At Least Twice A Year
At Least Twice a Year Weatherstrip Lubrication Silicone grease on weatherstrips will make them last Restraint System Check longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, Make sure the safety belt reminder light and all your damp weather more frequent application may be belts, buckles, latch plates, retractors and anchorages required.
Page 516: At Least Once A Year
Hydraulic Clutch System Check Starter Switch Check Check the ﬂuid level in the clutch reservoir. See Hydraulic Clutch on page 5-29 . A ﬂuid loss in this CAUTION: system could indicate a problem. Have the system inspected and repaired at once. When you are doing this inspection, the At Least Once a Year vehicle could move suddenly.
Page 517: Ignition Transmission Lock Check
Automatic Transmission Shift Lock 3. With the engine off, turn the key to the RUN position, but don’t start the engine. Without applying Control System Check the regular brake, try to move the shift lever out of PARK (P) with normal effort. If the shift lever moves out of PARK (P), your vehicle needs service.
Page 518: Underbody Flushing Service
Parking Brake and Automatic Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the Transmission Park (P) Mechanism parking brake. Check • To check the parking brake’s holding ability: With the engine running and transmission in NEUTRAL (N), slowly remove foot pressure from CAUTION:...
Page 519: Part C: Periodic Maintenance Inspections
Part C: Periodic Exhaust System Inspection Maintenance Inspections Inspect the complete exhaust system. Inspect the body near the exhaust system. Look for broken, damaged, Listed in this part are inspections and services which missing or out-of-position parts as well as open seams, should be performed at least twice a year (for instance, holes, loose connections or other conditions which each spring and fall).
Page 520: Throttle System Inspection (V6 Only)
Throttle System Inspection Transfer Case and Front Axle (V6 Only) (Four-Wheel Drive) Inspection Inspect the throttle system for interference or binding, Every 12 months or at engine oil change intervals, and for damaged or missing parts. Replace parts check front axle and transfer case and add lubricant as needed.
Page 521: Part D: Recommended Fluids And Lubricants
Part D: Recommended Fluids and Usage Fluid/Lubricant Lubricants Hydraulic Hydraulic Clutch Fluid (GM Part No. Clutch System U.S. 12345347, in Canada (5–Speed 10953517, or equivalent DOT-3 Fluids and lubricants identiﬁed below by name, part Trans.) brake ﬂuid). number or speciﬁcation may be obtained from your Hydraulic dealer.
Page 522 Usage Fluid/Lubricant Usage Fluid/Lubricant Manual TranSynd™ Synthetic Transmission SAE 75W-90 Synthetic Axle Transmission Fluid (GM Part No. U.S. 12378515, Lubricant (GM Part No. U.S. (6–Speed) in Canada 88900701). Rear Axle 12378261, in Canada 10953455) or equivalent meeting GM Speciﬁcation ® Automatic DEXRON -III Automatic...
Page 523 Usage Fluid/Lubricant Usage Fluid/Lubricant Front Axle Body Door Propshaft Hinge Pins, Spline or Spline Lubricant, Special Lubricant Tailgate Hinge Multi-Purpose Lubricant, Superlube One-Piece (GM Part No. U.S. 12345879, in and Linkage, (GM Part No. U.S. 12346241, in Propshaft Canada 10953511) or lubricant Folding Seats Canada 10953474, or equivalent).
Page 524: Part E: Maintenance Record
Part E: Maintenance Record After the scheduled services are performed, record the date, odometer reading and who performed the service and any additional information from “Owner Checks and Services” or “Periodic Maintenance” on the following record pages. Also, you should retain all maintenance receipts. Maintenance Record Odometer Maintenance Record...
Page 525 Maintenance Record (cont’d) Odometer Maintenance Record Date Serviced By Reading 6-23...
Page 526 Maintenance Record (cont’d) Odometer Maintenance Record Date Serviced By Reading 6-24...
Page 527: Customer Assistance Information
Section 7 Customer Assistance Information Customer Assistance Information ......7-2 Reporting Safety Defects ........7-8 Customer Satisfaction Procedure ......7-2 Reporting Safety Defects to the United States Online Owner Center ........7-3 Government ..........7-8 Customer Assistance for Text Telephone (TTY) Reporting Safety Defects to the Canadian Users ............7-4 Government ..........7-9 Customer Assistance Offices ......7-4...
Page 528: Customer Assistance Information
Your satisfaction and goodwill are important to the windshield.) your dealer and to Chevrolet. Normally, any concerns with the sales transaction or the operation of your • Dealership name and location vehicle will be resolved by your dealer’s sales or service...
Page 529: Online Owner Center
Online Owner Center The BBB Auto Line Program is an out of court program administered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle The Owner Center is a resource for your GM ownership repairs or the interpretation of the New Vehicle needs.
Page 530: Customer Assistance For Text Telephone (Tty) Users
Canada – Customer Assistance speech-impaired and who use Text Telephones (TTYs), General Motors of Canada Limited Chevrolet has TTY equipment available at its Customer Customer Communication Centre, 163-005 Assistance Center. Any TTY user can communicate with 1908 Colonel Sam Drive Chevrolet by dialing: 1-800-833-CHEV (2438).
Page 531: Gm Mobility Program For Persons With Disabilities
To enhance Chevrolet’s strong commitment to customer satisfaction, Chevrolet is excited to announce the establishment of the Chevrolet Roadside Assistance This program, available to Center. As the owner of a 2003 Chevrolet, membership qualiﬁed applicants, can in Roadside Assistance is free. reimburse you up to $1,000...
Page 532: Canadian Roadside Assistance
Basic Care and Courtesy Care are not part of or included in the coverage provided by the New Vehicle Limited • Roadside Basic Care services (as outlined Warranty. Chevrolet reserves the right to modify or previously) discontinue Basic Care and Courtesy Care at any time. Plus: The Roadside Assistance Center uses companies that •...
Page 533: Courtesy Transportation
Warranty service can generally be completed while you Chevrolet has always exempliﬁed quality and value in wait. However, if you are unable to wait Chevrolet its offering of motor vehicles. To enhance your helps minimize your inconvenience by providing several ownership experience, we and our participating dealers transportation options.
Page 534: Reporting Safety Defects
Courtesy Rental Vehicle contact you dealer for speciﬁc information about availability. All Courtesy Transportation arrangements When your vehicle is unavailable due to overnight will be administered by appropriate dealer personnel. warranty repairs, your dealer may arrange to provide Canadian Vehicles: For warranty repairs during you with a courtesy rental vehicle or reimburse you for a the Complete Vehicle Coverage period of the General rental vehicle you obtained, at actual cost, up to a...
Page 535: Reporting Safety Defects To The Canadian Government
Please call us at 1-800-222-1020, or write: To contact NHTSA, you may either call the Auto Safety Chevrolet Motor Division Hotline toll-free at 1-800-424-9393 (or 366-0123 in Chevrolet Customer Assistance Center the Washington, D.C. area) or write to: P.O. Box 33170 NHTSA, U.S. Department of Transportation Detroit, MI 48232-5170 Washington, D.C.
Page 536: Current And Past Model Order Forms
Transmission, Transaxle, Transfer Without Portfolio: Owner’s Manual only. Case Unit Repair Manual RETAIL SELL PRICE: $25.00 Current and Past Model Order Forms This manual provides information on unit repair service procedures, adjustments, and speciﬁcations for GM Service Publications are available for current and transmissions, transaxles, and transfer cases.
Page 537 All-Wheel Drive ..........5-54 AM-FM Radio ..........3-72 Accessory Power Outlets ......... 3-19 AM ............. 3-123 Adding a Snow Plow or Similar Equipment ..4-61 Antenna, Fixed Mast ........3-125 Adding Washer Fluid ........5-43 Antenna, XM™ Satellite Radio Antenna Additional Program Information ......
Page 538 Audio System(s) (cont.) Battery ............5-47 Radio with CD ..........3-75 Before Leaving on a Long Trip ......4-44 Radio with Six-Disc CD ........ 3-98 Before You Drive ........... 3-111 Rear Seat Audio (RSA) ....... 3-120 Before You Go Off-Roading ......4-24 Setting the Time for Radios with Radio Data Body Lubrication Service ........
Page 539 Bulb Replacement (cont.) Chains, Tires ..........5-78 Taillamps ............ 5-65 CHANGE ENGINE OIL ........3-66 Buying New Tires ........... 5-74 Check Engine Light ......... 3-49 CHECK OIL LEVEL ......... 3-66 CHECK WASHER FLUID ......... 3-66 Checking Brake Fluid ........5-45 Checking Coolant ..........
Page 540 Child Restraints (cont.) Compass Variance ........2-55, 2-58 Top Strap ........... 1-42 Content Theft-Deferrent ........2-18 Where to Put the Restraint ......1-41 Control of a Vehicle .......... 4-5 Chime Level Adjustment ......... 3-125 Coolant ............3-47 Cigarette Lighter ..........3-20 Engine Temperature Gage ......
Page 541 Driving Through Deep Standing Water ....4-41 Driving Through Flowing Water ......4-41 Daytime Running Lamps ........3-15 Driving Uphill ..........4-29 Defensive Driving ..........4-2 Driving with a Trailer ........4-86 Defogging and Defrosting ......3-23, 3-31 Driving ............4-38 Delayed Locking ..........
Page 542 Electrical System (cont.) Engine (cont.) Power Windows and Other Power Options ..5-109 Starting ............2-22 Windshield Wiper Fuses ......5-109 Entertainment System ........3-125 Electrochromic Mirror Operation ....2-54, 2-57 Cleaning the Video Screen ......3-125 Electronic Transfer Case ........2-41 DVD Distortion ..........
Page 543 Flash-To-Pass Feature ........3-9 Fuel (cont.) Flat Tire, Changing ......... 5-80 Gage ............3-53 Flat Tire ............5-79 Gasoline Octane ........... 5-4 Fluid ............. 5-23 Gasoline Speciﬁcations ........5-5 Automatic Transmission ......5-23, 5-26 Low Warning Light ........3-54 Manual Transmission ........5-28 System Inspection ........
Page 544 How to Check Power Steering Fluid ....5-43 How to Check ......5-23, 5-26, 5-28, 5-70 Hazard Warning Flashers ........3-6 How to Inspect ..........5-21 Head Restraints ..........1-7 How to Use This Manual ........ii Headlamp High/Low Beam Changer ....3-9 How to Wear Safety Belts Properly ....
Page 545 Inspection (cont.) Steering and Suspension ......6-17 Lamps On Reminder ........3-15 Throttle System ........... 6-18 Lamps ............3-14 Transfer Case and Front Axle Exterior ............3-14 (All-Wheel Drive) ........6-18 Interior ............3-18 Transfer Case and Front Axle (Four-Wheel Lap Belt ............
Page 546 Light (cont.) Malfunction Indicator ........3-49 Maintenance, Normal Replacement Parts ..5-121 Passenger Air Bag Status Indicator ....3-40 Maintenance Schedule ........6-12 Safety Belt Reminder ........3-36 At Each Fuel Fill ......... 6-12 Tow/Haul Mode ........... 3-53 At Least Once a Month ........ 6-12 Traction Off ..........
Page 547 Maintenance Schedule (cont.) Mirrors (cont.) Transfer Case and Front Axle (All-Wheel Manual Rearview Mirror ........ 2-53 Drive) Inspection ........6-18 Outside Automatic Dimming Mirror ....2-61 Transfer Case and Front Axle (Four-Wheel Outside Camper-Type Mirrors ......2-59 Drive) Inspection ........6-18 Outside Convex Mirror .........
Page 548 Oil ..............5-16 Overseas – Customer Assistance ......7-4 Engine ............5-16 Owners, Canadian ..........ii Pressure Gage ..........3-51 Owner’s Information ........7-10 Older Children, Restraints ........ 1-31 Online Owner Center ........7-3 ® OnStar Personal Calling ......... 2-63 ®...
Page 549 Pickup Conversion to Chassis Cab ....4-67 AM-FM Radio ..........3-72 Plan Ahead When Possible ........ 7-7 Care of Your Cassette Tape Player ....3-123 Playing a Cassette Tape ........3-93 Care of Your CD and DVD Player ....3-124 Playing a Compact Disc ....
Page 550 Rear Seat Top Strap Anchors (Extended Cab Restraint System Check (cont.) Models) ............1-45 Replacing Restraint System Parts After a Rear Seat Top Strap Anchors Crash ............. 1-82 (Crew Cab Models) ........1-46 Restraint Systems ........... 1-81 Rear Window Defogger ......3-24, 3-31 Checking ............
Page 551 Safety Belts (cont.) Select Button ..........3-64 Rear Seat Passengers ......... 1-26 SERVICE 4 WHEEL STEER ......3-69 Right Front Passenger Position ...... 1-24 SERVICE 4WD ..........3-69 Safety Belt Extender ........1-31 SERVICE AIRBAG .......... 3-68 Safety Belt Use During Pregnancy ....1-23 SERVICE BRAKE BOOSTER ......
Page 552 Six-Speed (VORTEC™ 8100 V8 and Stuck in Sand, Mud, Ice or Snow ...... 4-52 DURAMAX™ 6600 V8 Engines) ....2-31 Sun Visors ............. 2-17 Skidding ............4-21 Supplemental Brake Assist System ...... 4-9 Snow Plow ............ 4-61 Swing-Out Windows ........2-17 Some Other Rainy Weather Tips .......
Page 553 Tires (cont.) Traction (cont.) Changing a Flat Tire ........5-80 Trailer Brakes ..........4-85 Dual Tire Operation ........5-70 Trailer Wiring Harness ........4-89 If a Tire Goes Flat ........5-79 Trailer ............4-67 Inﬂation -- Tire Pressure ....... 5-69 Recommendations ........
Page 554 Underbody Flushing Service ......6-16 Warning Lights, Gages and Indicators ....3-33 Underhood Fuse Block ........5-113 Warnings ............3-65 Understanding Radio Reception ....... 3-123 DIC Warnings and Messages ......3-65 Uniform Tire Quality Grading ......5-75 Hazard Warning Flashers ....... 3-6 United States –...
Page 555 When You Are Ready to Leave After Parking on a Hill ............4-89 XM™ Radio Satellite Service Where to Put the Restraint ....... 1-41 (USA Only) ......... 3-75, 3-85, 3-98 Why Safety Belts Work ........1-11 XM™ Satellite Radio Antenna System ....3-125 Windows ............
Page 556 NOTES...

Chevrolet 2003 Silverado Owner's Manual

Section 2 Features and Controls

Features and Controls

Doors and Locks

Starting and Operating Your Vehicle

Onstar System

Storage Areas

Vehicle Personalization

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages and Indicators

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Driving Your Vehicle

Your Driving, the Road, and Your Vehicle

Towing

Quick Links

Chapters

Related Manuals for Chevrolet 2003 Silverado

Summary of Contents for Chevrolet 2003 Silverado