Advertisement
Your Alarm and/or Remote Start unit has a configurable receiver that allows
the transmitter to be programmed to operate the Lock/Unlock functions with
one transmitter button or with two transmitter buttons (separate Lock/
Unlock). In addition, the receiver also allows driver priority function. This
driver priority function takes place when ever a particular transmitter is
used to unlock the vehicle regardless of the selection of one button or two
button operation.
The following indicates the receiver programmable slots:
1 Lock/Unlock or Lock
2 Unlock if Programmed
3 Trunk Release and/or Remote Start (Optional on some models)
4 Auxiliary Output
5 Auxiliary Output
6 Driver 1 Priority or Seperate Output
7 Driver 2 Priority or Separate Output
Receiver channels 6 or 7 will accept the programming of transmitter
channel 1 if used as the Lock/Unlock button, or Channel 2 when separate
Lock/Unlock buttons are programmed. In this way, whenever the transmitter
is used to unlock the vehicle, channel 6 or 7, when programmed, will
provide a pulsed ground output. This output can be connected to the driver
priority function of the vehicle to reset preset user features. Please consult
with your installation center technician to see if this feature is available in
your vehicle.
NOTE: A total of 4 transmitters may be programmed into any receiver
channel.
Force programming a transmitter, removing a transmitter, or reprioritizing a
transmitter is covered later in this manual.
Also, if you do not program a transmitter button into channel 2, which is the
separate unlock/disarm channel, then whatever button is programmed into
channel 1 will serve as both lock/arm & unlock/disarm.
NOTE: The RED Button serves as a function button in combination with other
buttons explained in your owner's manual. This button may not be used to
operate a receiver channel.
NOTE: The Option Button is predetermined and programmed for access to
Time Start, and Temperature Start & Check so it cannot be used for multiple
button operation of any other feature. It will however operate for any single
button programming.
This transmitter is also capable of one button programming for certain model
Model SS92
Programming Guide
128-8841
1 of 8
Advertisement
Related Manuals for Audiovox Auto Security SS92
Summary of Contents for Audiovox Auto Security SS92
- Page 1 Model SS92 Programming Guide Your Alarm and/or Remote Start unit has a configurable receiver that allows the transmitter to be programmed to operate the Lock/Unlock functions with one transmitter button or with two transmitter buttons (separate Lock/ Unlock). In addition, the receiver also allows driver priority function. This driver priority function takes place when ever a particular transmitter is used to unlock the vehicle regardless of the selection of one button or two button operation.
- Page 2 THIS PAGE LEFT BLANK INTENTIONALLY 128-8841 2 of 8...
-
Page 3: To Enter The Program Mode
Audiovox Alarms. If your alarm is one of these models, then when step 3 is completed on the following page, you can turn the ignition switch off and programming with the default button configurations for the first four chan- nels will be complete. - Page 4 10. Within 10 seconds, press and release the valet program switch one time. (Siren emits 5 short chirps indicating channel 5 has been entered.) 11. Within 10 seconds, press and hold any unused button(s) of the first transmitter you wish to control Channel 5 output, (Auxiliary Output 2) until a long chirp is heard from the siren.
-
Page 5: Recharging The Battery
slots in the receiver are occupied with transmitters you wish to continue to use, and all others are erased, you will have to fill all four receiver slots. If in step 3 you identified one transmitter, you will have to fill the additional 3 slots. - Page 6 To charge the battery using the supplied USB charger shown below: Connect the mini “B” type USB connector to the port located on the side of the trans- ceiver as shown in the diagram. This device complies with FCC Rules Part 15 Operation is subject to the following two conditions: 1.
- Page 7 ____/___/____ 8) Mail this form along with your payment to: Transmitter Ordering Department Audiovox Corporation 150 Marcus Blvd., Hauppauge N.Y. 11788 Credit card purchasers can order additional or replacement transmitters by phone. Simply dial 1 - 800 - 645 - 4994, and follow...
- Page 8 For Customer Service Visit Our Website At .audiovox.com Product Information, Photos, FAQ’s Owner’s Manuals © 2010 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY 11788 128-8841 128-8841 8 of 8...