Table of Contents
Advertisement
Quick Links
swisherinc.com
OWNER'S
MANUAL
MODEL NO.
LS722X
STARTING SERIAL #:
L206-010001
IMPORTANT
Read and follow all Safety
Precautions and Instructions
before operating this
equipment.
Rev. 06-010
1602 CORPORATE DRIVE, WARRENSBURG, MISSOURI 64093
Manufacturing quality lawn care equipment since 1945
11624
LOG
SPLITTER
Safety
Assembly
Operation
Service and Adjustment
Repair Parts
FAX 660-747-8650
PHONE 660-747-8183
Made In The
USA
Advertisement
Table of Contents
Related Manuals for Swisher LS722X
Summary of Contents for Swisher LS722X
- Page 1 OWNER’S MANUAL MODEL NO. LS722X STARTING SERIAL #: L206-010001 IMPORTANT Read and follow all Safety Precautions and Instructions before operating this equipment. Rev. 06-010 1602 CORPORATE DRIVE, WARRENSBURG, MISSOURI 64093 Manufacturing quality lawn care equipment since 1945 11624 SPLITTER...
-
Page 2: Limited Warranty
Should you have any questions concerning this warranty, please contact us toll-free at 1-800-222-8183. The model number, serial number, date of purchase, and the name of the authorized Swisher dealer from whom you purchased the splitter will be needed before any warranty claim can be processed. - Page 3 SAFETY PRECAUTIONS This Safety Alert Symbol indicates important messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of personal injury. Read this manual completely. This machine can amputate hands, feet, and throw objects. Failure to observe the following safety instructions could result in serious injury or death.
- Page 4 NEVER operate your splitter near a flame or spark. Hydraulic oil and gasoline are flammable and can • explode. NEVER fill gas tank while the engine is hot or running. Allow the engine to cool before refueling. • This unit is equipped with an internal combustion engine and should not be used on or near any •...
- Page 5 This log splitter has been partially assembled at the factory. Refer to the drawings and part lists should it become necessary to disassemble the unit for repair or replacement of parts. Inspect all components for damage. If you believe you have a damaged part please contact customer service immediately at 1-800-222-8183.
- Page 6 POSITIONING THE CYLINDER Remove lock pins from the cylinder retention clips and rotate clips down exposing the open slots on the cylinder retention bracket (reference Figure 2). Slide the Cylinder forward until the rear trunnions clear the slots then lift the back side of the cylinder until the rear trunnions clear the cylinder retention bracket and slide cylinder back until the front cylinder trunnions slide into the open slots of the cylinder retention bracket (reference arrow in Figure 2).
- Page 7 WARNING: NEVER OPERATE THE SPLITTER WITH THE CYLINDER IN THE STORED POSITION. SPLITTER OPERATION Set up the log splitter in a clear, level area and block the wheels. The suction port on the tank should always be on the lower side of the log splitter. Place a log on the beam, against the foot plate.
- Page 8 Exercise extreme caution, as some parts are very heavy and will require sufficient persons or mechanical handling equipment. Your Swisher Log Splitter has been produced with components designed specifically to this machine. Although standard springs, hardware and ect may look similar to parts used on other machinery, they may in some cases be made of a different construction and/or materials.
-
Page 9: Safety Decals
SAFETY DECALS Replace decals immediately if damaged. OD16 – FUEL SHUT OFF DECAL OD07 – COLD WEATHER DECAL (NOT ALL MODELS) OD12 – HYDRAULIC FILL PLUG 11794 – CAUTION DECAL DECAL OD33– SPEED DECAL 11427 – LS DANGER DECAL... - Page 10 ASSEMBLY DETAIL LS722X MODELS...
-
Page 11: Service Parts
Nut 3/8-16 Serr Flange Bolt 5/16-18 X 3/4 Serr Flange Nut 5/16-18 Serr Flange #16 Hose Clamp 20" Suction Hose Hydraulic Pump-LS722X Pressure Line Fitting Motor Base Weldment Tongue Support Weldment 3/8 X 2 1/2 Safety Hitch Pin Bolt 3/8-16 X 2 1/2 GR 5... - Page 12 ITEM NUMBER Bolt 5/16-18 X 1 1/4 HCC GR5 W asher 17/32 X 1 1/4 X 16GA BEAM DETAIL DESCRIPTION Beam W eldment W edge W eldment W edge GIB Angle Bolt 3/8-16 X 1 1/4 Carriage Nut 3/8-16 Nyloc Nut 1/2-13 Nyloc Jam 1/2-13 X 3 1/2 GR5 ZP Ram Cylinder...
-
Page 13: Engine Detail
ITEM # DESCRIPTION Beam Pivot Weldment Bolt 3/4-10 X 2 GR8 Washer Belleville 1.50 OD X .761 ID X .098 X .134 Washer 3/4 SAE Nut 3/4-10 Nyloc Bolt 1/2-13 X 4 GR5 Nut 1/2-13 Nyloc 1/2 X 3 1/2 HITCH PIN W/ HAIR PIN 3/8 X 1 5/8 Ball Lok Pin Plastic Lanyard 1/4-20 X 3/4 Serrated Flange Bolt GR5... - Page 14 NOTES ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________...
-
Page 15: Specifications
SPECIFICATIONS Models LS722X Splitting 22 Tons Force 7 HP Briggs and Engine Stratton Intek Splitting Horizontal/Vertical Positions Cylinder 4" X 24" Size 2 Stage with Heavy Pump Duty Bearings Pump 11 Gallons Per Minute Specs Valve Auto Return Belt Drive with... -
Page 16: Log Splitter
All Log Splitter parts listed herein may be ordered directly from Swisher Mower & Machine Co. Inc., your nearest Swisher dealer, or from our website. All engine parts may be ordered from the nearest dealer of the engine supplied with your log splitter without notice.