Assembly And Set-Up/Charging Battery; Charging The Battery; Attaching The Handlebars - Razor E100 series Owner's Manual

CHARGING BATTERY
q Charging the Battery
Charge the battery prior to use.
• Initial charge time: 12 hours
• Recharge time: up to 12 hours, even if the light
turns green. Recommended maximum charging
time is 24 hours.
• Always charge the battery immediately after
riding.
• Fully charge battery before storing for extended
periods of time.
• Unplug charger from the wall outlet when not
in use.
• Failure to recharge battery periodically may
result in a battery that will not accept a charge.
• Make sure scooter power switch is turned OFF
when unit is not in use. If the power switch is
left on for an extended period of time, the battery
may reach a stage at which it will no longer hold
a charge.
Charger
Charger
Charger
Plug
Port
ASSEMBLY AND SET-UP
q Attaching the Handlebars
Tools required: 5 mm Allen Wrench
1
Loosen the collar clamp and
slide it upward. With a clock-
wise twisting motion, push and
"thread" the steering tube onto
the fork until it bottoms out on
the fork headset lock nut.
q Inflating the Tire
The front tire is inflated when shipped, but it invariably may lose some pressure between the point of
manufacturing and your purchase. Always inflate tire to the correct PSI before first time use.
• To ensure long battery life, never store the product
in freezing or below freezing temperatures!
Freezing will permanently damage the battery.
• Run time: Up to 40 minutes of continuous ride
time. Run time may vary depending on riding
conditions, climate and/or proper maintenance.
• Constant stopping and starting may shorten
ride time.
• Average battery life for a properly maintained unit
is approx. 250 charge/discharge cycles.
LED Light
1
Plug the charger into a wall
outlet. If the lights on charger
do not light up, check the power
to the outlet. If necessary, try a
different outlet.
1
Using a bicycle-style tire pump
equipped for a Schrader-type valve,
inflate the front tire to the correct
PSI indicated on the sidewall of
the tire.
2
Turn scooter power switch OFF
before charging. Plug the charger
into the charger port on the
electric scooter.
2
With the front wheel pointed
straight ahead and the handle-
bars square to the front wheel,
tighten the clamp as shown.
Tighten securely.
3
WARNING:
Rechargeable batteries are
only to be charged under adult
supervision. Always disconnect
your scooter from the charger
before cleaning with damp cloth.
Note: If your charger does not
look like the one illustrated,
your unit has been supplied
with an alternative charger.
The specifications and charging
procedure would not change.
The charger has a small window
with one LED to indicate the
charge status. Refer to the
illustration on the charger unit
for the actual "charging" and
"charged" status indications for
your model charger.
Chargers have built-in over-
charge protection to prevent
battery from being over-charged.
Charger may get warm during
use. This is normal for some
chargers and is no cause for
concern. If your charger does
not get warm during use, it
does not mean that it is not
working properly.
WARNING: Battery
charge can deplete over time.
Periodically recharge battery
when not in use.
Note: Make sure the cables/
wires are out of the way before
inserting the stem in the fork.
WARNING: Failure to
properly tighten the collar clamp
may allow the handlebars to
dislodge while riding and may
cause you to lose control and fall.
When correctly tightened, the
handlebars will not rotate out of
alignment with the front wheel
under normal circumstances.
Note: The cable and wire
assembly from the handlebar
must not wrap around the
steering tube or handlebar. Sharp
bends or twisting of the brake
cable can cause the brakes to
malfunction.
Note: The pressure air supplies
found at gasoline stations are
designed to inflate high-volume
automobile tires. If you decide
to use such an air supply to
inflate your electric scooter tires,
first make sure the pressure
gauge is working, then use very
short bursts to inflate to the
correct PSI. If you inadvertently
over-inflate the tire, release the
excess pressure immediately.