Page 1 Maintenance and Service Guide HP Compaq nc6400 Notebook PC Document Part Number: 406847-001 May 2006 This guide is a troubleshooting reference used for maintaining and servicing the computer. It provides comprehensive information on identifying computer features, components, and spare parts; troubleshooting computer problems; and performing...
Page 2 Java is a trademark of Sun Microsystems, Inc. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
Page 3: Table Of Contents
1 Product Description 1.1 Features ........1–2 1.2 Resetting the Computer.
Page 4 Contents 3 Illustrated Parts Catalog 3.1 Serial Number Location ..... . 3–1 3.2 Computer Major Components....3–2 3.3 Display Assembly Components .
Page 5 Contents 5 Removal and Replacement Procedures 5.1 Serial Number ......5–2 5.2 Disassembly Sequence Chart .
Page 6: Specifications
Contents 6 Specifications Screw Listing B Backup and Recovery C Display Component Recycling D Connector Pin Assignments E Power Cord Set Requirements Index Maintenance and Service Guide...
Page 7: Product Description
Product Description The HP Compaq nc6400 Notebook PC offers advanced modularity, Intel® Core™ Duo and Core Solo processors, and extensive multimedia support. HP Compaq nc6400 Notebook PC Maintenance and Service Guide 1–1...
Page 8: Features
Product Description 1.1 Features ■ The following processors, varying by computer model: ❏ Intel Core Duo T2600 (2.17-GHz) processor ❏ Intel Core Duo T2500 (2.00-GHz) processor ❏ Intel Core Duo T2400 (1.83-GHz) processor ❏ Intel Core Duo T2300 (1.67-GHz) processor ❏...
Page 9 ■ External 90- and 65-watt AC adapters with 3-wire power cord, varying by computer model ■ 8-cell and 4-cell Li-Ion batteries ■ Stereo speakers ■ Volume up, volume mute, and volume down buttons ■ Support for the following optical drives: ❏...
Page 10: Resetting The Computer
Product Description 1.2 Resetting the Computer If the computer you are servicing has an unknown password, follow the steps below to reset the password. These steps also clear CMOS. ✎ The following steps will not clear an unknown password if the stringent security option has been enabled in the BIOS.
Page 11: Power Management
1.3 Power Management The computer comes with power management features that extend battery operating time and conserve power. The computer supports the following power management features: ■ Standby ■ Hibernation ■ Setting customization by the user ■ Hotkeys for setting the level of performance ■...
Page 12: External Components
Bluetooth® device, is turned on. ■ On: The computer is on. ■ Blinking: The computer is in standby. ■ Blinking rapidly: An HP Smart AC Adapter with a higher power rating should be connected. ■ Off: The computer is off or in hibernation.
Page 13 ■ Blinking green: The hard drive or optical drive is being accessed. ■ Amber: HP Mobile Data Protection has temporarily parked the hard drive. Provides wireless communication between the computer and an optional IrDA-compliant device.
Page 14 Product Description The external components on the right side of the computer are shown below and described in Table 1-2. Right-Side Components 1–8 Maintenance and Service Guide...
Page 15: Right-Side Components
Item Component Smart card slot MultiBay II device USB port RJ-45 (network) jack RJ-11 (modem) jack Maintenance and Service Guide Table 1-2 Right-Side Components Function Supports optional smart cards and Java™ Cards. Supports an optical disc. The type of optical drive varies by computer model.
Page 16 Product Description The external components on the left side of the computer are shown below and described in Table 1-3. Left-Side Components 1–10 Maintenance and Service Guide...
Page 17: Left-Side Components
Item Component Exhaust vent USB ports (2) Audio-in (microphone) jack Audio-out (headphone) jack PC Card slot Maintenance and Service Guide Table 1-3 Left-Side Components Function Provides airflow to cool internal components. Ä To prevent overheating, do not obstruct vents. Use the computer only a hard, flat surface.
Page 18 Product Description The external components on the rear panel of the computer are shown below and described in Table 1-4. Rear Panel Components 1–12 Maintenance and Service Guide...
Page 19: Rear Panel Components
Item Component Security cable slot Battery bay Smart adapter power connector S-Video-out jack External monitor port Maintenance and Service Guide Table 1-4 Rear Panel Components Function Attaches an optional security cable to the computer. Ä Security solutions are designed to act as deterrents.
Page 20 Product Description The standard keyboard components of the computer are shown below and described in Table 1-5. Standard Keyboard Components 1–14 Maintenance and Service Guide...
Page 21 Standard Keyboard Components Item Component fn key caps lock key f1 to f12 keys (12) num lock key Embedded keypad Arrow keys Windows applications key Windows logo key Maintenance and Service Guide Table 1-5 Function Executes frequently used system functions when pressed in combination with a function key or the esc key.
Page 22 Product Description The computer top components are shown below and described in Table 1-6. Top Components 1–16 Maintenance and Service Guide...
Page 23: Top Components
Item Component Power button Info Center button Wireless button Presentation button Volume mute button Volume down button Volume up button Maintenance and Service Guide Table 1-6 Top Components Function When the computer is: ■ Off, press to turn on the computer. ■...
Page 24 Product Description The computer top components are shown below and described in Table 1-7. Top Components 1–18 Maintenance and Service Guide...
Page 25 Item Component Power light Wireless light Caps lock light Num lock light Fingerprint reader Maintenance and Service Guide Table 1-7 Top Components Function ■ On: The computer is on. ■ Blinking: The computer is in standby. ■ Blinking rapidly: An AC adapter with a higher power rating should be connected.
Page 26 Product Description The computer pointing device components are shown below and described in Table 1-8. Pointing Device Components 1–20 Maintenance and Service Guide...
Page 27: Pointing Device Components
Pointing Device Components Item Component Pointing stick Pointing stick buttons TouchPad TouchPad buttons TouchPad scroll zone Maintenance and Service Guide Table 1-8 Function Moves the pointer and selects or activates items on the screen. Function like the left, middle, and right buttons on an external mouse.
Page 28: Bottom Components
1–22 Table 1-9 Bottom Components Function Holds the battery. Connects the computer to an optional docking device. Release the battery from the battery bay. Connects an optional HP Ultra-Capacity Battery or HP Extended Life Battery. Maintenance and Service Guide...
Page 29 Bottom Components (Continued) Item Component Exhaust vents Hard drive bay Memory module compartment Bluetooth compartment Serial number Mini Card compartment Maintenance and Service Guide Table 1-9 Function Provides airflow to cool internal components. Ä To prevent overheating, do not obstruct vents. Use the computer only a hard, flat surface.
Page 30: Design Overview
Product Description 1.5 Design Overview This section presents a design overview of key parts and features of the computer. Refer to to identify replacement parts, and Replacement Procedures,” The system board provides the following device connections: ■ Audio ■ Display ■...
Page 31: Troubleshooting
Å WARNING: Only authorized technicians trained by HP should repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly-/module-level repair. Because of the complexity of the individual boards and subassemblies, do not attempt to make repairs at the component level or modifications to any printed wiring board.
Page 32: Selecting From The File Menu
Troubleshooting 2. Select the File, Security, Diagnostics, or System Configuration menu. 3. To close Computer Setup and restart the computer: ❏ Select File > Save changes and exit, and then press – or – ❏ Select File > Ignore changes and exit, and then press –...
Page 33: Selecting From The Security Menu
Selecting from the Security Menu Select Setup Password Power-On Password Password Options (Password options can be selected only when a power-on password has been set.) DriveLock Passwords Smart Card Security TPM Embedded Security System IDs Disk Sanitizer *Not applicable to SuperDisk LS-120 drives. Maintenance and Service Guide Table 2-2 Security Menu...
Page 34: Selecting From The Diagnostics Menu
Troubleshooting Selecting from the Diagnostics Menu Select HDD Self-Test Options Memory Check 2–4 Table 2-3 Diagnostics Menu To Do This Run a quick comprehensive self test on hard drives in the system that support the test features. Run a quick comprehensive test on system memory on the following categories: ■...
Page 35: Selecting From The System Configuration Menu
Selecting from the System Configuration Menu Select Language Boot Options Device Configurations Built-In Device Options Port Options Maintenance and Service Guide Table 2-4 System Configuration Menu To Do This Change the Computer Setup language. Enable/disable MultiBoot, which sets a startup sequence that can include most bootable devices and media in the system.
Page 36: Troubleshooting Flowcharts
Troubleshooting 2.2 Troubleshooting Flowcharts Troubleshooting Flowcharts Overview Flowchart Description “Flowchart 2.1—Initial Troubleshooting” “Flowchart 2.2—No Power, Part 1” “Flowchart 2.3—No Power, Part 2” “Flowchart 2.4—No Power, Part 3” “Flowchart 2.5—No Power, Part 4” “Flowchart 2.6—No Video, Part 1” “Flowchart 2.7—No Video, Part 2” “Flowchart 2.8—Nonfunctioning Docking Device (if applicable)”...
Page 37: Flowchart 2.1—Initial Troubleshooting
Flowchart 2.1—Initial Troubleshooting Begin troubleshooting. Is there power? Beeps, LEDs, or error messages? Is there video? (no boot) Is the OS loading? Is there sound? Maintenance and Service Guide Go to “Flowchart 2.2—No Power, Part 1.” Check LED board, speaker connections.
Page 38: Flowchart 2.2—No Power, Part
Troubleshooting Flowchart 2.2—No Power, Part 1 No power (power LED is off). Remove from docking device (if applicable). Power up on battery power? Power up on AC power? Power up in docking device? 1. Reset the power cables in the docking device and at the AC outlet.
Page 39: Flowchart 2.3—No Power, Part
Flowchart 2.3—No Power, Part 2 Continued from “Flowchart 2.2—No Power, Part 1.” Visually check for debris in battery socket and clean if necessary. Power on? Check battery by recharging it, moving it to another computer, or replacing it. Power on? Done Maintenance and Service Guide Done...
Page 40: Flowchart 2.4—No Power, Part
Troubleshooting Flowchart 2.4—No Power, Part 3 Continued from “Flowchart 2.3—No Power, Part 2.” Plug directly into AC outlet. Power LED Reseat AC adapter in computer and at power source. Power on? Power outlet active? Replace power cord. Power on? 2–10 Done Done Internal or...
Page 41: Flowchart 2.5—No Power, Part
Flowchart 2.5—No Power, Part 4 Continued from “Flowchart 2.4—No Power, Part 3.” Open computer. Loose or damaged parts? Close computer and retest. Power on? Done Maintenance and Service Guide Reseat loose components and boards and replace damaged items. Replace the following items (if applicable). Check computer operation after each replacement: 1.
Page 42: Flowchart 2.6—No Video, Part
Troubleshooting Flowchart 2.6—No Video, Part 1 No video. Docking Device Stand-alone or docking device? Stand-alone Internal or external display*? Internal External Adjust brightness. Video OK? Replace the following one at a time. Test after each replacement. Check for bent pins on cable. Video OK? Done 2–12...
Page 43: Flowchart 2.7—No Video, Part
Flowchart 2.7—No Video, Part 2 Continued from “Flowchart 2.6—No Video, Part 1.” Remove computer from docking device, if connected. Adjust display brightness. Video OK? Check that computer is properly seated in docking device, for bent pins on cable, and for monitor connection.
Page 44 Troubleshooting Flowchart 2.8—Nonfunctioning Docking Device (if applicable) Nonfunctioning docking device. Reset power cord in docking device and power outlet. Check voltage setting on docking device. Reset monitor cable connector at docking device. Docking device operating? Replace docking device. 2–14 Reinstall computer into docking device.
Page 45: Flowchart 2.9—No Operating System (Os) Loading
Flowchart 2.9—No Operating System (OS) Loading No OS loading.* Reset power cord in docking device and power outlet. *NOTE: Before beginning troubleshooting, always check cable connections, cable ends, and drives for bent or damaged pins. Maintenance and Service Guide No OS loading from hard drive, go to “Flowchart 2.10—No OS Loading, Hard Drive, Part 1.”...
Page 46 Troubleshooting Flowchart 2.10—No OS Loading, Hard Drive, Part 1 OS not loading from hard drive. Nonsystem disk message? Reseat external hard drive. OS loading? Boot from Check the Setup utility for correct booting order. Boot from hard drive? Done 2–16 Go to “Flowchart 2.11—No OS...
Page 47 Flowchart 2.11—No OS Loading, Hard Drive, Part 2 Continued from “Flowchart 2.10—No OS Loading, Hard Drive, Part 1.” 1. Replace CD or diskette in 2. Replace system drive? Remove diskette and reboot. Boot from hard drive? Boot 2.13—No OS from diskette drive? Diskette Drive.”...
Page 48 Troubleshooting Flowchart 2.12—No OS Loading, Hard Drive, Part 3 Continued from “Flowchart 2.11—No OS Loading, Hard Drive, Part 2.” System files on hard drive? Virus hard drive? Run SCANDISK and check for bad sectors. Can bad sectors be fixed? Fix bad sectors.
Page 49: Flowchart 2.13—No Os Loading, Diskette Drive
Flowchart 2.13—No OS Loading, Diskette Drive OS not loading from diskette drive. Nonsystem disk message? Boot from another device? Diskette drive enabled in the Setup Utility? Is diskette drive boot order correct? Change boot priority using 2.17—Nonfunctioning the Setup Utility. Maintenance and Service Guide Reseat diskette drive.
Page 50: Flowchart 2.14—No Os Loading, Optical Drive
Troubleshooting Flowchart 2.14—No OS Loading, Optical Drive No OS loading from CD-ROM or DVD-ROM drive. Boots from CD or DVD? Reseat drive. 2–20 Disc in drive? Install bootable disc. bootable disc. Done Boots from CD or DVD? Booting from another 2.17—Nonfunctioning device? Reset the computer.
Page 51: Flowchart 2.15—No Audio, Part
Flowchart 2.15—No Audio, Part 1 No audio. Computer in docking device (if applicable)? Go to “Flowchart 2.16—No Audio, Part 2.” 2.17—Nonfunctioning Maintenance and Service Guide Turn up audio internally or externally. Undock docking device. Go to “Flowchart Device.” Troubleshooting Audio? Done Go to Internal...
Page 52: Flowchart 2.16—No Audio, Part
Troubleshooting Flowchart 2.16—No Audio, Part 2 Continued from “Flowchart 2.15—No Audio, Part 1.” Audio driver in OS configured? Correct drivers for application? Connect to external speaker. Audio? 2–22 Reload audio drivers. Load drivers and set configuration in OS. Replace audio board and speaker connections...
Page 53: Flowchart 2.17—Nonfunctioning Device
Flowchart 2.17—Nonfunctioning Device Unplug the nonfunctioning device from the computer and inspect cables and plugs for bent or broken pins or Clear CMOS. Reattach device. Close computer, plug in power, and reboot. Device boots properly? Done Maintenance and Service Guide Nonfunctioning device.
Page 54: Flowchart 2.18—Nonfunctioning Keyboard
Troubleshooting Flowchart 2.18—Nonfunctioning Keyboard Keyboard not operating properly. Connect computer to good external keyboard. External device works? Reseat internal keyboard connector (if applicable). Done 2–24 Replace system board. Replace internal keyboard or cable. Replace system board. Done Maintenance and Service Guide...
Page 55 Flowchart 2.19—Nonfunctioning Pointing Device Pointing device not operating properly. Connect computer to good external pointing device. External device works? Reseat internal pointing device connector (if applicable). Done Maintenance and Service Guide Replace system board. Replace internal pointing device or cable. Replace system board.
Page 56 Troubleshooting Flowchart 2.20—No Network/Modem Connection No network or modem connection. Network or modem jack active? Digital line? NIC/modem configured in OS? Disconnect all power from the computer and open. Reseat NIC/modem (if applicable). 2–26 Replace jack or have jack activated. Connect to nondigital line.
Page 57: Illustrated Parts Catalog
Illustrated Parts Catalog This chapter provides an illustrated parts breakdown and a reference for spare part numbers. 3.1 Serial Number Location When ordering parts or requesting information, provide the computer serial number and computer model number located on the bottom of the computer. Serial Number Location Maintenance and Service Guide 3–1...
Page 58: Computer Major Components
Illustrated Parts Catalog 3.2 Computer Major Components Computer Major Components 3–2 Maintenance and Service Guide...
Page 59 Spare Parts: Computer Major Components Item Description Display assemblies (include wireless antenna transceivers and cables) 14.1-inch, WXGA+ 14.1-inch, WXGA Refer to Section 3.3, “Display Assembly Components,” assembly internal component spare part number information. Switch cover Power button board (includes power button board cable) Keyboards For use in:...
Page 60 Illustrated Parts Catalog Computer Major Components 3–4 Maintenance and Service Guide...
Page 61 Spare Parts: Computer Major Components (Continued) Item Description Cable Kit Includes: Pointing stick cable TouchPad cable Modem cable Audio cable Bluetooth cable RTC battery Microphone Top cover (includes TouchPad, smart card reader, and fingerprint sensor board) Plastics Kit PC Card slot bezel Hard drive cover Memory cover Mini Card cover...
Page 62 Illustrated Parts Catalog Computer Major Components 3–6 Maintenance and Service Guide...
Page 63 Spare Parts: Computer Major Components (Continued) Item Description Fan assembly System boards (include thermal grease, alcohol pad, and thermal pad) For use with heat sink with spare part number 418887-001 For use with heat sink with spare part number 418930-001 Heat sinks (include thermal grease, alcohol pad, and thermal pad) For use with discrete system board (spare part number 418904-001)
Page 64 Illustrated Parts Catalog Computer Major Components 3–8 Maintenance and Service Guide...
Page 65 Spare Parts: Computer Major Components (Continued) Item Description Hard drives 7200 rpm 60 GB MultiBay II drives (include bezel) DVD±RW and CD-RW Double-Layer Combo Drive DVD±RW and CD-RW Combo Drive DVD-ROM drive Battery 8-cell, 5.1-AH 4-cell, 2.5-AH Maintenance and Service Guide Table 3-1 5400 rpm 418861-001...
Page 66 Illustrated Parts Catalog Computer Major Components 3–10 Maintenance and Service Guide...
Page 67 Spare Parts: Computer Major Components (Continued) Item Description Mini Card WLAN modules 802.11b/g HS WLAN module for use in North America 802.11b/g HS WLAN module for use in the countries listed below. These countries are categorized as the rest of the world (ROW). China Ecuador Haiti...
Page 68 Illustrated Parts Catalog Computer Major Components 3–12 Maintenance and Service Guide...
Page 69 Spare Parts: Computer Major Components (Continued) Item Description Mini Card WLAN modules (Continued) 802.11a/b/g GL WLAN module for use in the countries listed below. These countries are categorized as most of the world (MOW 2). Aruba Austria Azerbaijan Bahrain Belgium Bermuda Bulgaria Cayman Islands...
Page 70 Illustrated Parts Catalog Computer Major Components 3–14 Maintenance and Service Guide...
Page 71 Spare Parts: Computer Major Components (Continued) Item Description Mini Card WLAN modules (Continued) 802.11b/g GL WLAN module for use in the following countries: Israel Jordan Bluetooth® module (includes Bluetooth module cable) Maintenance and Service Guide Table 3-1 Kuwait United Arab Emirates Thailand Illustrated Parts Catalog...
Page 72: Display Assembly Components
Illustrated Parts Catalog 3.3 Display Assembly Components 3–16 Maintenance and Service Guide...
Page 73 Display Assembly Components Spare Part Number Information Item Description Display bezel Display panels 14.1-inch, WXGA+ 14.1-inch, WXGA Display Hinge Kit Display Inverter Wireless Antenna Kit Display enclosure Not illustrated: Display Bracket Kit (includes left display bracket) Display Cable Kit (for use with 14.1-inch, WXGA+ display panel) Display Cable Kit (for use with 14.1-inch, WXGA display panel)
Page 74: Plastics Kit
Illustrated Parts Catalog 3.4 Plastics Kit 3–18 Maintenance and Service Guide...
Page 75 Spare Part Number Information Item Description Plastics Kit Includes: PC Card slot bezel Hard drive cover (includes 2 captive screws, captured by C clips) Memory module compartment cover (includes 1 captive screw, captured by C clip) Mini Card module compartment cover (includes 1 captive screw, captured by C clip) Bluetooth module cover (includes 1 captive screw, captured by C clip) Computer feet (4)
Page 76: Cable Kit
Illustrated Parts Catalog 3.5 Cable Kit Spare Part Number Information Item Description Cable Kit Includes: Pointing stick cable Bluetooth module cable Audio cable Modem module cable TouchPad cable 3–20 Table 3-4 Cable Kit Maintenance and Service Guide Spare Part Number 418876-001...
Page 77: Mass Storage Devices
3.6 Mass Storage Devices Spare Part Number Information Item Description Hard drives (include frame and connector) 7200 rpm 60 GB Optical drives (include bezel) DVD±RW and CD-RW Double-Layer Combo Drive DVD±RW and CD-RW Combo Drive DVD-ROM drive Maintenance and Service Guide Table 3-5 Mass Storage Devices 5400 rpm...
Page 78: Miscellaneous (Not Illustrated)
65-watt PFC AC adapter External MultiBay II External MultiBay II power cable and stand HP Extended Life Battery HP Docking Station HP Docking Station Miscellaneous Plastics Kit Label Kit MultiBay 8X DVD-ROM Drive MultiBay 24X DVD/CD-RW Combo Drive Nylon carrying case 3–22...
Page 79 Miscellaneous (Not Illustrated) Spare Part Information (Continued) Description Power cords: For use in the United States For use in Australia For use in Europe For use in the United Kingdom For use in Italy For use in Denmark For use in Brazil For use in Japan For use in the People’s Republic of China For use in Korea...
Page 80 Illustrated Parts Catalog Miscellaneous (Not Illustrated) Spare Part Information (Continued) Description USB 1.1 diskette drive Screw Kit (includes the following screws; refer to Appendix A, “Screw Listing,” specifications and usage) ■ Phillips PM3.0×3.0 screw ■ Phillips PM2.5×17.0 screw ■ Phillips PM2.5×13.0 spring-loaded screw ■...
Page 81: Sequential Part Number Listing
USB 1.1 diskette drive 366143-001 External MultiBay II 366144-001 External MultiBay II power cable and stand 367456-001 HP Extended Life Battery 374803-001 HP Docking Station 380089-001 HP Docking Station Miscellaneous Plastics Kit Maintenance and Service Guide Table 3-7 Illustrated Parts Catalog 3–25...
Page 82 Illustrated Parts Catalog Sequential Part Number Listing (Continued) Spare Part Number Description 407107-001 802.11b/g HS WLAN Mini Card module for use in North America 407107-002 802.11b/g HS WLAN Mini Card module for use in the ROW countries listed below: China Ecuador Haiti 407107-291...
Page 83 Sequential Part Number Listing (Continued) Spare Part Number Description 407576-002 802.11a/b/g GL WLAN Mini Card module for use in the MOW2 countries listed below: Aruba Austria Azerbaijan Bahrain Belgium Bermuda Bulgaria Cayman Islands Columbia Croatia Cyprus The Czech Republic Denmark Egypt 407576-003 802.11a/b/g GL WLAN Mini Card module for use in the ROW...
Page 84 Illustrated Parts Catalog Sequential Part Number Listing (Continued) Spare Part Number Description 418851-001 1-DIMM, PC2-4200, 512-MB memory module 418852-001 1-DIMM, PC2-4200, 1024-MB memory module 418853-001 1-DIMM, PC2-4200, 2048-MB memory module 418854-001 1-DIMM, PC2-5300, 256-MB memory module 418855-001 1-DIMM, PC2-5300, 512-MB memory module 418856-001 1-DIMM, PC2-5300, 1024-MB memory module 418857-001...
Page 85: Display Bezel
Sequential Part Number Listing (Continued) Spare Part Number Description 418872-001 65-watt AC adapter 418873-001 90-watt non-PFC AC adapter 418874-001 Intel Core Duo T2600 (2.17-GHz) processor (includes thermal paste) 418875-001 90-watt PFC AC adapter 418876-001 Cable Kit 418877-001 Plastics Kit 418878-001 Screw Kit 418879-001 Label Kit...
Page 86: Display Hinge Kit 418902-001
Illustrated Parts Catalog Sequential Part Number Listing (Continued) Spare Part Number Description 418890-001 14.1-inch, WXGA display panel 418891-001 14.1-inch, WXGA+ display panel 418892-001 Display Screw Kit 418893-001 Display Rubber Kit 418894-001 Display Bracket Kit 418895-001 Display enclosure 418896-001 14.1-inch, WXGA display assembly (includes wireless antenna transceivers and cables) 418897-001 Display Cable Kit for use with WXGA display panel...
Page 87 Sequential Part Number Listing (Continued) Spare Part Number Description 418910-031 Keyboard for use in the United Kingdom 418910-041 Keyboard for use in Germany 418910-051 Keyboard for use in France 418910-061 Keyboard for use in Italy 418910-071 Keyboard for use in Spain 418910-081 Keyboard for use in Denmark 418910-091...
Page 88 Illustrated Parts Catalog Sequential Part Number Listing (Continued) Spare Part Number Description 418910-A41 Keyboard for use in Belgium 418910-AB1 Keyboard for use in Taiwan 418910-AD1 Keyboard for use in Korea 418910-BA1 Keyboard for use in Slovenia 418910-BB1 Keyboard for use in Israel 418910-DD1 Keyboard for use in Iceland 418930-001...
Page 89: Removal And Replacement Preliminaries
Removal and Replacement This chapter provides essential information for proper and safe removal and replacement service. 4.1 Tools Required You will need the following tools to complete the removal and replacement procedures: ■ Magnetic screwdriver ■ Phillips P0 and P1 screwdrivers ■...
Page 90: Service Considerations
Removal and Replacement Preliminaries 4.2 Service Considerations The following sections include some of the considerations that you should keep in mind during disassembly and assembly procedures. ✎ As you remove each subassembly from the computer, place the subassembly (and all accompanying screws) away from the work area to prevent damage.
Page 91: Preventing Damage To Removable Drives
4.3 Preventing Damage to Removable Drives Removable drives are fragile components that must be handled with care. To prevent damage to the computer, damage to a removable drive, or loss of information, observe the following precautions: ■ Before removing or inserting a hard drive, shut down the computer.
Page 92: Preventing Electrostatic Damage
Removal and Replacement Preliminaries 4.4 Preventing Electrostatic Damage Many electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, the discharge contains enough power to alter device parameters or melt silicon junctions.
Page 93: Packaging And Transporting Precautions
4.5 Packaging and Transporting Precautions Use the following grounding precautions when packaging and transporting equipment: ■ To avoid hand contact, transport products in static-safe containers, such as tubes, bags, or boxes. ■ Protect all electrostatic-sensitive parts and assemblies with conductive or approved containers or packaging. ■...
Page 94: Workstation Precautions
Removal and Replacement Preliminaries 4.6 Workstation Precautions Use the following grounding precautions at workstations: ■ Cover the workstation with approved static-shielding material (refer to ■ Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and equipment. ■...
Page 95: Grounding Equipment And Methods
4.7 Grounding Equipment and Methods Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ■ When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords.
Page 96: Typical Electrostatic Voltage Levels
Removal and Replacement Preliminaries Table 4-1 shows how humidity affects the electrostatic voltage levels generated by different activities. Typical Electrostatic Voltage Levels Event Walking across carpet Walking across vinyl floor Motions of bench worker Removing DIPS from plastic tube Removing DIPS from vinyl tray Removing DIPS from Styrofoam Removing bubble pack from PCB Packing PCBs in foam-lined box...
Page 97: Removal And Replacement Procedures
Removal and Replacement Procedures This chapter provides removal and replacement procedures. There are as many as 81 screws, in 14 different sizes, that must be removed, replaced, or loosened when servicing the computer. Make special note of each screw size and location during removal and replacement.
Page 98: Serial Number
Removal and Replacement Procedures 5.1 Serial Number Report the computer serial number to HP when requesting information or ordering spare parts. The serial number is located on the bottom of the computer. Serial Number Location 5–2 Maintenance and Service Guide...
Page 99: Disassembly Sequence Chart
5.2 Disassembly Sequence Chart Use the chart below to determine the section number to be referenced when removing computer components. Disassembly Sequence Chart Section Description Preparing the Computer for Disassembly Battery Hard Drive Computer Feet Bluetooth Module External Memory Module Mini Card WLAN Module Å...
Page 100 Removal and Replacement Procedures Disassembly Sequence Chart (Continued) Section Description 5.10 Keyboard 5.11 RTC Battery 5.12 Internal Memory Module 5.13 Modem Module 5.14 Mini Card WWAN Module 5.15 Switch Cover 5.16 Power Button Board 5.17 Fan Assembly 5.18 Heat Sink 5.19 Processor 5.20...
Page 101: Preparing The Computer For Disassembly
5.3 Preparing the Computer for Disassembly Before you begin any removal or installation procedures: 1. Shut down the computer. If you are unsure whether the computer is off or in hibernation, turn the computer on, and then shut it down through the operating system. 2.
Page 102 Removal and Replacement Procedures Battery Spare Part Number Information 8-cell, 5.1-AH 4-cell, 2.5-AH 4. Remove the battery by following these steps: a. Turn the computer upside down with the rear panel toward you. b. Slide the battery release latch on the right 1 and then the battery release latch on the left 2 to release the battery.
Page 103: Hard Drive
5.4 Hard Drive Hard Drive Spare Part Number Information 7200 rpm 60 GB 1. Prepare the computer for disassembly (refer to 2. Position the computer with the front toward you. Maintenance and Service Guide Removal and Replacement Procedures 5400 rpm 418861-001 100 GB 80 GB...
Page 104 Removal and Replacement Procedures 3. Loosen the two Phillips PM2.0×5.0 screws 1 that secure the hard drive cover to the computer. 4. Lift the right side of the hard drive cover 2 and swing it up and to the left. 5.
Page 105 6. Loosen the Phillips PM2.5×13.0 spring-loaded hard drive retention screw 1. 7. Grasp the mylar tab 2 on the hard drive and slide the hard drive 3 to the left to disconnect it from the system board. 8. Remove the hard drive 4 from the hard drive bay. Removing the Hard Drive Maintenance and Service Guide Removal and Replacement Procedures...
Page 106 Removal and Replacement Procedures 9. Remove the four Phillips PM3.0×3.0 hard drive frame screws 1 from each side of the hard drive. 10. Lift the frame 2 straight up to remove if from the hard drive. Removing the Hard Drive Frame Reverse the above procedure to reassemble and install the hard drive.
Page 107: Computer Feet
Removal and Replacement Procedures 5.5 Computer Feet The computer feet are adhesive-backed rubber pads. The feet are included in the Plastics Kit, spare part number 418877-001. Replacing the Computer Feet Maintenance and Service Guide 5–11...
Page 108: Bluetooth Module
Removal and Replacement Procedures 5.6 Bluetooth Module Bluetooth Module Spare Part Number Information Bluetooth module (includes Bluetooth module cable) 1. Prepare the computer for disassembly (refer to 2. Loosen the Phillips PM2.0×5.0 screw 1 that secures the Bluetooth module cover to the computer. 3.
Page 109 4. Slide the Bluetooth module 1 to the right until the left side of the module is clear of the left side of the clip in the base enclosure. 5. Swing the left side of the Bluetooth module 2 out of the base enclosure.
Page 110: External Memory Module
Removal and Replacement Procedures 5.7 External Memory Module Memory Module Spare Part Number Information PC2-5300 2048 MB 1024 MB 512 MB 256 MB 1. Prepare the computer for disassembly (refer to 2. Position the computer with the front toward you. 5–14 PC2-4200 418857-001...
Page 111 3. Loosen the Phillips PM2.0×5.0 screw 1 that secures the memory module compartment cover to the computer. 4. Lift the right edge of the cover 2 and swing it up and to the left. 5. Remove the memory module compartment cover. ✎...
Page 112 Removal and Replacement Procedures 6. Spread the retaining tabs 1 on each side of the memory module socket to release the memory module. (The edge of the module opposite the socket rises away from the computer.) 7. Slide the module 2 away from the socket at an angle. 8.
Page 113: Mini Card Wlan Module
5.8 Mini Card WLAN Module Spare Part Number Information 802.11b/g HS WLAN module for use in North America 802.11b/g HS WLAN module for use in the countries listed below. These countries are categorized as the rest of the world (ROW). China Ecuador Haiti...
Page 114 Removal and Replacement Procedures Spare Part Number Information (Continued) 802.11a/b/g GL WLAN module for use in the countries listed below. These countries are categorized as most of the world 2 (MOW2). Aruba Austria Azerbaijan Bahrain Belgium Bermuda Bulgaria Cayman Islands Columbia Croatia Cyprus...
Page 115 1. Prepare the computer for disassembly 2. Position the computer with the front toward you. 3. Loosen the Phillips PM2.0×5.0 screw 1 that secures the Mini Card module compartment cover to the computer. 4. Lift the front of the cover 2 and swing it up and toward the back of the computer.
Page 116 Removal and Replacement Procedures 6. Make note of which wireless antenna cable is attached to which antenna clip on the Mini Card WLAN module before disconnecting the cables, then disconnect the auxiliary and main wireless antenna cables 1 from the Mini Card WLAN module.
Page 117: Multibay Ii Device
5.9 MultiBay II Device MultiBay II Device Spare Part Number Information DVD±RW and CD-RW Double-Layer Combo Drive DVD±RW and CD-RW Combo Drive DVD-ROM drive 1. Prepare the computer for disassembly 2. Position the computer with the left side toward you. Maintenance and Service Guide Removal and Replacement Procedures (Section...
Page 118 Removal and Replacement Procedures 3. Remove the Phillips PM2.5×5.0 screw 1 that secures the MultiBay II device to the computer. 4. Push in on the right side of the MultiBay II device 2. (The MultiBay II device partially protrudes from the MultiBay II.) 5.
Page 119: Keyboard
5.10 Keyboard Keyboard Spare Part Number Information For use in: Belgium Brazil The Czech Republic Denmark France French Canada Germany Greece Hungary Iceland Internationally Israel Italy Japan Korea 1. Prepare the computer for disassembly 2. Position the computer with the front toward you. Maintenance and Service Guide Removal and Replacement Procedures 418910-A41...
Page 120 Removal and Replacement Procedures 3. Remove the three Torx8 T8M2.5×11.0 screws that secure the keyboard to the computer. Removing the Keyboard Screws 5–24 Maintenance and Service Guide...
Page 121 4. Turn the computer display-side up with the front toward you. 5. Open the computer as far as possible. 6. Slide the four release tabs 1 on the rear edge of the keyboard forward. 7. Lift the rear edge of the keyboard 2 and swing it up toward you until it rests on the palm rest.
Page 122 Removal and Replacement Procedures 8. Release the zero insertion force (ZIF) connector 1 to which the keyboard cable is attached and disconnect the keyboard cable 2. 9. Release the ZIF connector 3 to which the pointing stick cable is attached and disconnect the pointing stick cable 4. 10.
Page 123 11. If it is necessary to replace the pointing stick cable, turn the keyboard upside down with the space bar toward you. 12. Release the ZIF connector 1 to which the pointing stick cable is attached and disconnect the pointing stick cable 2. ✎...
Page 124: Rtc Battery
Removal and Replacement Procedures 5.11 RTC Battery ✎ The RTC battery is included in the Plastics Kit, spare part number 418877-001. 1. Prepare the computer for disassembly 2. Release the keyboard 3. Disconnect the RTC battery cable 1 from the system board and remove the cable from the clips 2 in the top cover.
Page 125: Internal Memory Module
5.12 Internal Memory Module Memory Module Spare Part Number Information PC2-5300 2048 MB 1024 MB 512 MB 256 MB 1. Prepare the computer for disassembly 2. Release the keyboard Maintenance and Service Guide Removal and Replacement Procedures PC2-4200 418857-001 2048 MB 418856-001 1024 MB 418855-001...
Page 126 Removal and Replacement Procedures 3. Spread the retaining tabs 1 on each side of the memory module socket to release the memory module. (The edge of the module opposite the socket rises away from the computer.) 4. Slide the module 2 away from the socket at an angle. 5.
Page 127: Modem Module
Removal and Replacement Procedures 5.13 Modem Module Modem Module Spare Part Number Information Modem module 418849-001 1. Prepare the computer for disassembly (Section 5.3). 2. Release the keyboard (Section 5.10). Maintenance and Service Guide 5–31...
Page 128 Removal and Replacement Procedures 3. Remove the two Phillips PM2.0×6.0 screws 1 that secure the modem module to the system board. 4. Lift the right side of the modem module 2 to disconnect it from the system board. 5. Disconnect the modem module cable 3 from the modem module.
Page 129: Mini Card Wwan Module
Removal and Replacement Procedures 5.14 Mini Card WWAN Module Mini Card WWAN Module Spare Part Number Information Mini Card WWAN module 418860-001 1. Prepare the computer for disassembly (Section 5.3). 2. Release the keyboard (Section 5.10). Maintenance and Service Guide 5–33...
Page 130 Removal and Replacement Procedures 3. Make note of which wireless antenna cable is attached to which antenna clip on the Mini Card WWAN module before disconnecting the cables, then disconnect the auxiliary and main wireless antenna cables 1 from the Mini Card WWAN module.
Page 131: Switch Cover
5.15 Switch Cover Switch Cover Spare Part Number Information Switch cover 1. Prepare the computer for disassembly 2. Remove the keyboard 3. Turn the computer upside down with the rear panel toward you. 4. Remove the two T8M2.5×11.0 screws 1 and the four Phillips PM2.0×2.0 screws 2 that secure the switch cover to the computer.
Page 132 Removal and Replacement Procedures 5. Turn the computer display-side up with front toward you. 6. Open the computer as far as possible. 7. Disconnect the power button board cable 1 from the system board. 8. Insert a thin flat-bladed tool under the hinge cover sections 2 of the switch cover and lift up until the switch cover 3 disengages from the computer.
Page 133: Power Button Board
5.16 Power Button Board Power Button Board Spare Part Number Information Power button board (includes power button board cable) 1. Prepare the computer for disassembly 2. Remove the keyboard 3. Remove the switch cover 4. Remove the two Phillips PM2.5×4.0 screws 1 that secure the power button board to the switch cover.
Page 134: Fan Assembly
Removal and Replacement Procedures 5.17 Fan Assembly Fan Assembly Spare Part Number Information Fan assembly 1. Prepare the computer for disassembly 2. Remove the keyboard 3. Remove the switch cover 4. Disconnect the fan cable 1 from the system board. 5.
Page 135: Heat Sink
5.18 Heat Sink Heat Sink Spare Part Number Information ✎ All heat sink spare part kits include thermal grease, alcohol pads, and thermal pads. For use with discrete system board (spare part number 418904-001) For use with UMA system board (spare part number 418931-001) 1.
Page 136 Removal and Replacement Procedures 2. Loosen the four Phillips PM2.0×10.0 screws 1 and the two Phillips PM2.0×13.0 screws 2 that secure the heat sink to the system board. 3. Remove the heat sink 3 from the base enclosure. ✎ Due to the adhesive quality of the thermal paste located between the heat sink and processor, it may be necessary to move the heat sink from side to side to detach the heat sink from the processor.
Page 137 Removal and Replacement Procedures ✎ The thermal paste and thermal pads should be thoroughly cleaned from the surfaces of the heat sink 1, processor 2, Chip1 3, and Chip2 4 each time the heat sink is removed. Thermal paste and thermal pads are included with all heat sink, processor, and system board spare part kits.
Page 138: Processor
Removal and Replacement Procedures 5.19 Processor Processor Spare Part Number Information Intel Core Duo T2600 (2.17-GHz) processor Intel Core Duo T2500 (2.00-GHz) processor Intel Core Duo T2400 (1.83-GHz) processor Intel Core Duo T2300 (1.67-GHz) processor Intel Core Solo T1300 (1.66-GHz) processor 1.
Page 139 2. Use a flat-bladed screwdriver to turn the processor locking screw 1 one-half turn counterclockwise until you hear a click. 3. Lift the processor 2 straight up and remove it. ✎ The gold triangle 3 on the processor should be aligned with the triangle icon 4 on the processor socket when you install the processor.
Page 140: Display Assembly
Removal and Replacement Procedures 5.20 Display Assembly Display Assembly Spare Part Number Information 14.1-inch, WXGA+ 14.1-inch, WXGA 1. Prepare the computer for disassembly 2. Disconnect the wireless antenna cables from the Mini Card WLAN module 3. Remove the keyboard 4. Disconnect the wireless antenna cables from the Mini Card WWAN module 5.
Page 141 6. Close the computer and turn it upside down with the rear panel toward you. 7. Remove the following screws: 1 Two Torx8 T8M2.5×11.0 screws from the computer bottom 2 Two Torx8 T8M2.5×7.0 screws from the computer rear panel 3 One Phillips PM2.5×5.0 screw from the computer battery Removing the Display Assembly Screws Maintenance and Service Guide Removal and Replacement Procedures...
Page 142 Removal and Replacement Procedures 8. Turn the computer display-side up with the front toward you. 9. Open the computer as far as it will open. 10. Disconnect the display cable 1 from the system board. 11. Remove the wireless antenna cables 2 and 3 from the Mini Card compartment and the top cover clips.
Page 143 Ä CAUTION: Support the display assembly when removing the following screws. Failure to support the display assembly can result in damage to the display assembly and other computer components. 12. Remove the two Torx8 T8M2.5×7.0 screws 1 that secure the display assembly to the computer.
Page 144 Removal and Replacement Procedures Display Assembly Components Spare Part Number Information Description Display bezel Display panels 14.1-inch, WXGA+ 14.1-inch, WXGA Display Hinge Kit Display Inverter Wireless Antenna Kit Display enclosure Display Bracket Kit (includes left display bracket) Display Cable Kit (for use with 14.1-inch, WXGA+ display panel) Display Cable Kit (for use with 14.1-inch, WXGA display panel) Display Screw Kit...
Page 145 14. Remove the following: 1 and 2 four rubber screw covers ✎ The two rubber screw covers 1 on the top edge of the display bezel are different from the two rubber screw covers 2 on the bottom edge of the display bezel. Both types of rubber screw covers are included in the Display Rubber Kit, spare part number 418893-001.
Page 146 Removal and Replacement Procedures Display Assembly Components Spare Part Number Information Description Display bezel Display enclosure 15. Flex the insides edges of the left and right sides 1 and the top and bottom sides 2 of the display bezel until the bezel disengages from the display enclosure.
Page 147 Display Assembly Components Spare Part Number Information Description Display Hinge Kit 17. If it is necessary to replace the display hinges, remove the Phillips PM2.5×4.0 screw 1 and the Phillips PM2.5×6.0 screw 2 that secure each hinge to the display enclosure. 18.
Page 148 Removal and Replacement Procedures Display Assembly Components Spare Part Number Information Description Display panels 14.1-inch, WXGA+ 14.1-inch, WXGA 19. Remove the four mylar screw covers 1 and the four Phillips PM2.0×3.0 screws 2 that secure the display panel to the display enclosure.
Page 149 Display Assembly Components Spare Part Number Information Description Display Inverter 22. Disconnect the display 1 and backlight cables 2 from the inverter. 23. Remove the inverter 3. Removing the Display Inverter Maintenance and Service Guide Removal and Replacement Procedures Spare Part Number 418888-001 5–53...
Page 150 Removal and Replacement Procedures Display Assembly Components Spare Part Number Information Description Wireless Antenna Kit 24. If it is necessary to replace the wireless antenna transceivers and cables, remove the two Torx T8M2.5×4.0 screws 1 that secure the left and right transceivers to the display enclosure. 25.
Page 151: Top Cover
5.21 Top Cover Top Cover Spare Part Number Information Top cover (includes TouchPad, smart card reader, and fingerprint sensor board) 1. Prepare the computer for disassembly and then remove the following components: a. Keyboard b. Switch cover c. Fan assembly d.
Page 152 Removal and Replacement Procedures 3. Remove the following: 1 Two rubber screw covers 2 Nine Torx8 T8M2.5×11.0 screws that secure the top cover to the base enclosure 3 One Phillips PM2.5×5.0 screw that secures the top cover to the base enclosure Removing the Top Cover Screws, Part 1 5–56 Maintenance and Service Guide...
Page 153 4. Turn the computer right-side up with the front toward you. 5. Disconnect the following cables from the system board: 1 TouchPad cable 2 Fingerprint reader board cable 3 Smart card assembly cable Disconnecting the Top Cover Cables Maintenance and Service Guide Removal and Replacement Procedures 5–57...
Page 154 Removal and Replacement Procedures 6. Remove the microphone 1 from the clip in the top cover and the cable 2 from the routing clips in the top cover. Releasing the Microphone 5–58 Maintenance and Service Guide...
Page 155 Removal and Replacement Procedures 7. Remove the two Torx8 T8M2.5×7.0 screws that secure the top cover to the base enclosure. Removing the Top Cover Screws, Part 2 Maintenance and Service Guide 5–59...
Page 156 Removal and Replacement Procedures 8. Swing the rear edge of the top cover 1 up and forward 2 until the left and right sides disengage from the base enclosure. 9. Remove the top cover 3. Removing the Top Cover Reverse the above procedure to install the top cover. 5–60 Maintenance and Service Guide...
Page 157: Pc Card/Digital Media Board
Removal and Replacement Procedures 5.22 PC Card/Digital Media Board PC Card/Digital Media Board Spare Part Number Information PC Card/digital media board 418884-001 1. Prepare the computer for disassembly (Section 5.3), and then remove the following components: a. Keyboard (Section 5.10) b.
Page 158 Removal and Replacement Procedures 2. Remove the three Phillips PM2.5×5.0 screws 1 that secure the PC Card/digital media board to the system board. 3. Lift up on the right side of the PC Card/digital media board 2 to disconnect the board from the system board. Removing the PC Card/Digital Media Board 5–62 Maintenance and Service Guide...
Page 159 4. If it is necessary to remove the PC Card assembly from the digital media board, disengage the hooks 1 on the PC Card assembly from the tabs on the digital media board. 5. Remove the PC Card assembly 2 from the digital media board.
Page 160: Speaker
Removal and Replacement Procedures 5.23 Speaker Speaker Spare Part Number Information Speaker 1. Prepare the computer for disassembly and then remove the following components: a. Keyboard b. Switch cover c. Fan assembly d. Heat sink e. Display assembly f. Top cover g.
Page 161 2. Disconnect the speaker cable 1 from the system board. 3. Remove the speaker 2 from the base enclosure. Removing the Speaker Reverse the above procedure to install the speaker. Maintenance and Service Guide Removal and Replacement Procedures 5–65...
Page 162: Microphone
Removal and Replacement Procedures 5.24 Microphone Microphone Spare Part Number Information Microphone 1. Prepare the computer for disassembly and then remove the following components: a. Keyboard b. Switch cover c. Fan assembly d. Heat sink e. Display assembly f. Top cover g.
Page 163 2. Disconnect the microphone cable 1 from the system board. 3. Remove the microphone 2 from the base enclosure. Removing the Microphone Reverse the above procedure to install the microphone. Maintenance and Service Guide Removal and Replacement Procedures 5–67...
Page 164: System Board
Removal and Replacement Procedures 5.25 System Board System Board Spare Part Number Information For use with heat sink with spare part number 418887-001 For use with heat sink with spare part number 418930-001 ✎ When replacing the system board, be sure that the following components are removed from the defective system board and installed on the replacement system board: ■...
Page 165 1. Prepare the computer for disassembly and then remove the following components: a. Hard drive b. Bluetooth board c. MultiBay II device d. Keyboard e. Switch cover f. Fan assembly g. Heat sink h. Display assembly i. Top cover j. PC Card/digital media board k.
Page 166 Removal and Replacement Procedures 2. Turn the computer upside down with the front toward you. 3. Remove the two Phillips PM2.0×6.0 screws on each side of the hard drive connector that secure the system board to the base enclosure. Removing the System Board Screws, Part 1 5–70 Maintenance and Service Guide...
Page 167 4. Turn the computer right-side up with the front toward you. 5. Remove the audio board cables 1 from the space between the system board and the base enclosure. 6. Disconnect the audio board cable 2 from the system board. 7.
Page 168 Removal and Replacement Procedures 8. Disconnect the modem module cable 1 from the system board. ✎ The modem module cable is available in the Cable Kit, spare part number 418876-001. 9. Release the ZIF connector 2 to which the LED board cable is attached and disconnect the LED board cable 3 from the system board.
Page 169 Removal and Replacement Procedures 10. Remove the four Phillips PM2.5×5.0 screws that secure the system board to the base enclosure. Removing the System Board Screws, Part 2 Maintenance and Service Guide 5–73...
Page 170 Removal and Replacement Procedures 11. Use the hard drive connector 1 to lift the right side of the system board 2 until it rests at an angle. 12. Slide the system board 3 away at an angle and remove it. Removing the System Board 5–74 Maintenance and Service Guide...
Page 171 13. If it is necessary to replace the audio cable, disconnect the cable from the three connectors on the system board and remove the cable. ✎ The audio cable is available in the Cable Kit, spare part number 418876-001. Removing the Audio Cable Maintenance and Service Guide Removal and Replacement Procedures 5–75...
Page 172 Removal and Replacement Procedures 14. If it is necessary to replace the modem connector and cable, remove the connector 1 from the clip in the base enclosure and remove the cable 2 from the routing channel in the base enclosure. ✎...
Page 173: Multibay Ii Eject Assembly
5.26 MultiBay II Eject Assembly Spare Part Number Information MultiBay II eject assembly 1. Prepare the computer for disassembly and then remove the following components: a. Hard drive b. Bluetooth board c. MultiBay II device d. Keyboard e. Switch cover f.
Page 174 Removal and Replacement Procedures 2. Remove the Phillips PM2.0×6.0 screw 1 that secures the MultiBay II eject assembly to the base enclosure. 3. Remove the MultiBay II eject assembly 2 from the base enclosure. Removing the MultiBay II Eject Assembly Reverse the above procedure to install the MultiBay II eject assembly.
Page 175 This chapter provides physical and performance specifications. Dimensions Height (front to back) Width Depth Weight Input Power Operating voltage Operating current Temperature Operating (not writing to optical disc) Operating (writing to optical disc) Nonoperating Maintenance and Service Guide Specifications Table 6-1 Computer Metric 2.9 to 3.4 cm...
Page 176 Specifications Relative humidity (noncondensing) Operating Nonoperating Maximum altitude (unpressurized) Operating (14.7 to 10.1 psia) Nonoperating (14.7 to 4.4 psia) Shock Operating Nonoperating Random Vibration Operating Nonoperating ✎ Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this range of temperatures. 6–2 Table 6-1 Computer (Continued)
Page 177 Dimensions Height Width Diagonal Number of colors Contrast ratio Brightness Pixel resolution Pitch Format Configuration Backlight Character display Total power consumption Viewing angle Maintenance and Service Guide Table 6-2 14.1-inch, WXGA 21.3 cm 28.5 cm 35.8 cm Up to 16.8 million 250:1 180 nits typical 0.279 ×...
Page 178: Hard Drives
Specifications Dimensions Height Width Weight Interface type Transfer rate Synchronous (maximum) Security Seek times (typical read, including setting) Single track Average Maximum † Logical blocks Disc rotational speed Operating temperature ✎ Certain restrictions and exclusions apply. Consult Customer Care for details. *1 GB = 1 billion bytes when referring to hard drive storage capacity.
Page 179 DVD±RW and CD-RW Combo Drive Applicable disc Center hole diameter Disc diameter Standard disc Mini disc Maintenance and Service Guide Table 6-4 Read: DVD-R, DVD-RW, DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18), CD-ROM (Mode 1 and 2) CD Digital Audio CD-XA ready (Mode 2, Form 1 and 2) CD-I ready (Mode 2, Form 1 and 2)
Page 180 Specifications DVD±RW and CD-RW Combo Drive (Continued) Disc thickness Track pitch Access time Random Full stroke Audio output level Cache buffer Data transfer rate CD-R (16X) CD-RW (8X) CD-ROM (24X) DVD (8X) DVD-R (4X) DVD-RW (2X) Multiword DMA mode 2 Startup time Stop time 6–6...
Page 181 Applicable disc Center hole diameter Disc diameter Standard disc Mini disc Disc thickness Track pitch Access time Random Full stroke Audio output level Cache buffer Data transfer rate CD-R (24X) CD-RW (10X) CD-ROM (24X) DVD (8X) Multiword DMA mode 2 Startup time Stop time Maintenance and Service Guide...
Page 182: System Dma
Specifications Hardware DMA DMA0 DMA1* DMA2* DMA3 DMA4 DMA5* DMA6 DMA7 *PC Card controller can use DMA 1, 2, or 5. 6–8 Table 6-6 System DMA System Function Not applicable Not applicable Not applicable Not applicable Direct memory access controller Available for PC Card Not assigned Not assigned...
Page 183: System Interrupts
Hardware IRQ IRQ0 IRQ1 IRQ2 IRQ3 IRQ4 IRQ5* IRQ6 IRQ7* IRQ8 IRQ9* IRQ10* Maintenance and Service Guide Table 6-7 System Interrupts System Function System timer Standard 101-/102-Key or Microsoft Natural Keyboard Cascaded Intel 82801DB/DBM USB2 Enhanced Host Controller—24CD COM1 Conexant AC—Link Audio Intel 82801DB/DBM SMBus Controller—24C3 Data Fax Modem with SmartCP Diskette drive...
Page 184 Specifications System Interrupts (Continued) IRQ11 IRQ12 IRQ13 IRQ14 IRQ15 *Default configuration; audio possible configurations are IRQ5, IRQ7, IRQ9, IRQ10, or none. ✎ PC Cards may assert IRQ3, IRQ4, IRQ5, IRQ7, IRQ9, IRQ10, IRQ11, or IRQ15. Either the infrared or the serial port may assert IRQ3 or IRQ4. 6–10 Table 6-7 Intel USB EHCI controller—24CD...
Page 185 I/O Address (hex) 000 - 00F 010 - 01F 020 - 021 022 - 024 025 - 03F 02E - 02F 040 - 05F 044 - 05F 062 - 063 065 - 06F 070 - 071 072 - 07F 080 - 08F 090 - 091 093 - 09F 0A0 - 0A1...
Page 186 Specifications System I/O Addresses (Continued) I/O Address (hex) 0A2 - 0BF 0C0 - 0DF 0E0 - 0EF 0F0 - 0F1 0F2 - 0FF 100 - 16F 170 - 177 178 - 1EF 1F0 - 1F7 1F8 - 200 202 - 21F 220 - 22F 230 - 26D 26E - 26...
Page 187 System I/O Addresses (Continued) I/O Address (hex) 2F0 - 2F7 2F8 - 2FF 300 - 31F 320 - 36F 370 - 377 378 - 37F 380 - 387 388 - 38B 38C - 3AF 3B0 - 3BB 3BC - 3BF 3C0 - 3DF 3E0 - 3E1 3E2 - 3E3...
Page 188: System Memory Map
Specifications Size Memory Address 640 KB 00000000-0009FFFF 128 KB 000A0000-000BFFFF 48 KB 000C0000-000CBFFF 160 KB 000C8000-000E7FFF 64 KB 000E8000-000FFFFF 15 MB 00100000-00FFFFFF 58 MB 01000000-047FFFFF 58 MB 04800000-07FFFFFF 2 MB 08000000-080FFFFF 4 GB 08200000-FFFEFFFF 64 KB FFFF0000-FFFFFFFF 6–14 Table 6-9 System Memory Map System Function Base memory...
Page 189: Screw Listing
This appendix provides specification and reference information for the screws used in the computer. All screws listed in this appendix are available in the Screw Kit, spare part number 418878-001, and the Display Screw Kit, spare part number 418892-001. Where used: 4 screws that secure the hard drive frame to the hard drive (documented in Section 5.4)
Page 190 Screw Listing Where used: Two screws that secure the hard drive cover to the computer (screws are captured on the cover by C-clips; documented in One screw that secures the Bluetooth module cover to the computer (screw is captured on the cover by a C-clip; documented in One screw that secures the memory module compartment cover to the computer (screw is captured on the cover by a C-clip;...
Page 191 Phillips PM2.5×13.0 Spring-Loaded Screw Where used: One screw that secures the hard drive to the computer (screw is captured on the cover by a C-clip; documented in Phillips PM2.5×13.0 Screw Location Maintenance and Service Guide Table A-3 Color Qty. Length Silver 13.0 mm Section...
Page 192 Screw Listing Where used: One screw that secures the MultiBay II device to the computer (documented in Section 5.9) Phillips PM2.5×5.0 Screw Location A–4 Table A-4 Phillips PM2.5×5.0 Screw Color Qty. Black Length Thread 5.0 mm 2.5 mm Maintenance and Service Guide Head Width 5.0 mm...
Page 193 Phillips PM2.5×5.0 Screw (Continued) Where used: One screw that secures the display assembly to the computer (documented Section 5.20) One screw that secures the top cover to the computer (documented in Section 5.21) Phillips PM2.5×5.0 Screw Locations Maintenance and Service Guide Table A-4 Color Qty.
Page 194 Screw Listing Phillips PM2.5×5.0 Screw (Continued) Where used: 3 screws that secure the PC Card/digital media board to the computer (documented in Section Phillips PM2.5×5.0 Screw Locations A–6 Table A-4 Color Qty. Black 5.22) Length Thread 5.0 mm 2.5 mm Maintenance and Service Guide Head Width...
Page 195 Phillips PM2.5×5.0 Screw (Continued) Where used: 4 screws that secure the system board to the computer (documented in Section 5.25) Phillips PM2.5×5.0 Screw Locations Maintenance and Service Guide Table A-4 Color Qty. Length Black 5.0 mm Screw Listing Head Thread Width 2.5 mm 5.0 mm...
Page 196 Screw Listing Where used: Three screws that secure the keyboard to the computer (documented in Section 5.10) Two screws that secure the switch cover to the computer (documented in Section 5.15) Two screws that secure the display assembly to the computer (documented Section 5.20) Torx8 T8M2.5×11.0 Screw Locations...
Page 197 Torx8 T8M2.5×11.0 Screw (Continued) Where used: 9 screws that secure the top cover to the computer (documented in Section 5.21) Torx8 T8M2.5×11.0 Screw Locations Maintenance and Service Guide Table A-5 Color Qty. Length Black 11.0 mm Screw Listing Head Thread Width 2.5 mm 5.0 mm...
Page 198 Screw Listing Where used: 2 screws that secure the modem module to the computer (documented in Section 5.13) Phillips PM2.0×6.0 Screw Locations A–10 Table A-6 Phillips PM2.0×6.0 Screw Color Qty. Silver Length Thread 6.0 mm 2.0 mm Maintenance and Service Guide Head Width 5.0 mm...
Page 199 Phillips PM2.0×6.0 Screw (Continued) Where used: 2 screws that secure the system board to the computer (documented in Section 5.25) Phillips PM2.0×6.0 Screw Locations Maintenance and Service Guide Table A-6 Color Qty. Length Silver 6.0 mm Screw Listing Head Thread Width 2.0 mm 5.0 mm...
Page 200 Screw Listing Phillips PM2.0×6.0 Screw (Continued) Where used: One screw that secures the MultiBay II eject assembly to the base enclosure (documented in Section Phillips PM2.0×6.0 Screw Location A–12 Table A-6 Color Qty. Silver 5.26) Length Thread 6.0 mm 2.0 mm Maintenance and Service Guide Head Width...
Page 201 Where used: 2 screws that secure the Mini Card WLAN to the computer (documented in Section 5.8) Phillips PM2.0×3.0 Screw Locations Maintenance and Service Guide Table A-7 Phillips PM2.0×3.0 Screw Color Qty. Silver Screw Listing Length Thread 3.0 mm 2.0 mm Head Width 5.0 mm...
Page 202 Screw Listing Phillips PM2.0×3.0 Screw (Continued) Where used: 2 screws that secure the Mini Card WWAN to the computer (documented in Section 5.14) Phillips PM2.0×3.0 Screw Locations A–14 Table A-7 Color Qty. Length Silver 3.0 mm Maintenance and Service Guide Head Thread Width...
Page 203 Where used: 2 screws that secure the power button board to the switch cover (documented in Section 5.16) Phillips PM2.5×4.0 Screw Locations Maintenance and Service Guide Table A-8 Phillips PM2.5×4.0 Screw Color Qty. Silver Screw Listing Length Thread 4.0 mm 2.5 mm Head Width...
Page 204 Screw Listing Phillips PM2.5×4.0 Screw (Continued) Where used: 2 screws that secure the display hinges to the display assembly (documented in Section 5.20) Phillips PM2.5×4.0 Screw Locations A–16 Table A-8 Color Qty. Length Silver 4.0 mm Maintenance and Service Guide Head Thread Width...
Page 205 Where used: 2 screws that secure the wireless antenna transceivers to the display assembly (documented in Section Torx8 T8M2.5×4.0 Screw Locations Maintenance and Service Guide Table A-9 Torx8 T8M2.5×4.0 Screw Color Qty. Silver 5.20) Screw Listing Length Thread 4.0 mm 2.5 mm Head Width...
Page 206 Screw Listing Where used: Four screws that secure the heat sink to the computer (screws are secured to the heat sink by C-clips; documented in Where used: Two screws that secure the heat sink to the computer (screws are secured to the heat sink by C-clips;...
Page 207 Screw Listing Phillips PM2.5×10.0 and Phillips PM2.5×13.0 Screw Locations Maintenance and Service Guide A–19...
Page 208 Screw Listing Where used: 4 screws that secure the switch cover to the computer (documented in Section 5.15) Phillips PM2.0×2.0 Screw Locations A–20 Table A-12 Phillips PM2.0×2.0 Screw Color Qty. Black Length Thread 2.0 mm 2.0 mm Maintenance and Service Guide Head Width 6.0 mm...
Page 209 Where used: One screw that secures the fan assembly to the computer (documented in Section 5.17) Torx8 T8M2.5×7.0 Screw Location Maintenance and Service Guide Table A-13 Torx8 T8M2.5×7.0 Screw Color Qty. Black Screw Listing Length Thread 7.0 mm 2.5 mm Head Width 5.0 mm...
Page 210 Screw Listing Torx8 T8M2.5×7.0 Screw (Continued) Where used: 2 screws that secure the display assembly to the computer (documented in Section 5.20) Torx8 T8M2.5×7.0 Screw Locations A–22 Table A-13 Color Qty. Length Black 7.0 mm Maintenance and Service Guide Head Thread Width 2.5 mm...
Page 211 Torx8 T8M2.5×7.0 Screw (Continued) Where used: 2 screws that secure the display assembly to the computer (documented in Section 5.20) Torx8 T8M2.5×7.0 Screw Locations Maintenance and Service Guide Table A-13 Color Qty. Length Black 7.0 mm Screw Listing Head Thread Width 2.5 mm 5.0 mm...
Page 212 Screw Listing Torx8 T8M2.5×7.0 Screw (Continued) Where used: One screw that secures the top cover to the computer (documented in Section 5.21) Torx8 T8M2.5×7.0 Screw Location A–24 Table A-13 Color Qty. Length Black 7.0 mm Maintenance and Service Guide Head Thread Width 2.5 mm...
Page 213 Torx8 T8M2.5×7.0 Screw (Continued) Where used: 2 screws that secure the top cover to the computer (documented in Section 5.21) Torx8 T8M2.5×7.0 Screw Locations Maintenance and Service Guide Table A-13 Color Qty. Length Black 7.0 mm Screw Listing Head Thread Width 2.5 mm 5.0 mm...
Page 214 Screw Listing Where used: 4 screws that secure the display bezel to the display assembly (documented in Section 5.20) Phillips PM2.5×6.0 Screw Locations A–26 Table A-14 Phillips PM2.5×6.0 Screw Color Qty. Silver Length Thread 6.0 mm 2.5 mm Maintenance and Service Guide Head Width 5.0 mm...
Page 215 Phillips PM2.5×6.0 Screw (Continued) Where used: 2 screws that secure the display hinges to the display assembly (documented in Section 5.20) Phillips PM2.5×6.0 Screw Locations Maintenance and Service Guide Table A-14 Color Qty. Length Silver 6.0 mm Screw Listing Head Thread Width 2.5 mm...
Page 216 Screw Listing Phillips PM2.5×6.0 Screw (Continued) Where used: 2 screws that secure the display panel to the display assembly (documented in Section 5.20) Phillips PM2.5×6.0 Screw Locations A–28 Table A-14 Color Qty. Length Silver 6.0 mm Maintenance and Service Guide Head Thread Width...
Page 217: Backup And Recovery
✎ HP installed drivers, utilities, and applications can be copied to a CD or to a DVD using HP Backup and Recovery Manager. ✎ Formatted DVD±RW discs and DVD±RW double-layer discs are not compatible with HP Backup and Recovery Manager.
Page 218: Backing Up Specific Files Or Folders
This process will take several minutes, depending on the file size and the speed of the computer. To back up specific files or folders: 1. Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery Manager. 2. Click Next.
Page 219: Backing Up The Entire Hard Drive
This process may take over an hour, depending on your computer speed and the amount of data being stored. To back up your entire hard drive: 1. Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery Manager. 2. Click Next.
Page 220 You can schedule recovery points for a specific time or event in your system. To create and schedule a system recovery point: 1. Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery Manager. 2. Click Next.
Page 221: Scheduling Backups
Scheduling Backups To schedule backups: 1. Select Start > All Programs > HP Backup & Recovery > HP Backup Scheduler. The “Backup Scheduler” page opens. 2. Click Next. 3. Schedule system recovery points at specific intervals (now, daily, weekly, or monthly) or at specific events, such as at...
Page 222: Creating Recovery Discs
After setting up the computer for the first time, you can create a set of recovery discs of the full factory image, using Recovery Media Creator in the HP Backup and Recovery Manager. The recovery discs are used to start up (boot) the computer and recover the operating system and software to factory settings in case of system failure or instability.
Page 223: Performing A Recovery
Recovery Media Creator, you will be prompted to continue the disc creation process where you left off. To create a set of recovery discs: 1. Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery Manager. 2. Click Next.
Page 224: Performing A Recovery From The Hard Drive
Initiating a Recovery in Windows To initiate a recovery in Windows: 1. Back up all personal files. 2. Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery Manager. 3. Click Next. 4. Click Recover important files or the entire system, and then click Next.
Page 225 Careful handling should be exercised when removing these components. ✎ Materials Disposal This HP product contains mercury in the backlight in the display assembly that might require special handling at end-of-life. Disposal of mercury may be regulated because of environmental considerations. For disposal or recycling information, contact your local authorities or the Electronic Industries Alliance (EIA) http://www.eiae.org...
Page 226 Display Component Recycling This appendix provides disassembly instructions for the display assembly. The display assembly must be disassembled to gain access to the backlight 1 and the liquid crystal display (LCD) panel 2. ✎ Disassembly procedures differ from one display assembly to another.
Page 227 Display Component Recycling Perform the following steps to disassemble the display assembly: 1. Remove all screw covers 1 and screws 2 that secure the display bezel to the display assembly. Removing the Display Bezel Screw Covers and Screws Maintenance and Service Guide C–3...
Page 228 Display Component Recycling 2. Lift up and out on the left and right inside edges 1 and the top and bottom inside edges 2 of the display bezel until the bezel disengages from the display assembly. 3. Remove the display bezel 3. Removing the Display Bezel C–4 Maintenance and Service Guide...
Page 229 Display Component Recycling 4. Disconnect all display panel cables 1 from the display inverter and remove the inverter 2. Removing the Display Inverter Maintenance and Service Guide C–5...
Page 230 Display Component Recycling 5. Remove all screws 1 that secure the display panel assembly to the display enclosure. 6. Remove the display panel assembly 2 from the display enclosure. Removing the Display Panel Assembly C–6 Maintenance and Service Guide...
Page 231 Display Component Recycling 7. Turn the display panel assembly upside down. 8. Remove all screws that secure the display panel frame to the display panel. Removing the Display Panel Frame Screws Maintenance and Service Guide C–7...
Page 232 Display Component Recycling 9. Use a sharp-edged tool to cut the tape 1 that secures the sides of the display panel to the display panel frame. 10. Remove the display panel frame 2 from the display panel. Removing the Display Frame C–8 Maintenance and Service Guide...
Page 233 11. Remove the screws 1 that secure the backlight cover to the display panel. 12. Lift the top edge of the backlight cover 2 and swing it forward. 13. Remove the backlight cover. Removing the Backlight Cover Maintenance and Service Guide Display Component Recycling C–9...
Page 234 Display Component Recycling 14. Turn the display panel right-side up. 15. Remove the backlight cables 1 from the clip 2 in the display panel. Releasing the Backlight Cables C–10 Maintenance and Service Guide...
Page 235 Display Component Recycling 16. Turn the display panel upside down. 17. Remove the backlight frame from the display panel. Removing the Backlight Frame Maintenance and Service Guide C–11...
Page 236 Display Component Recycling Å WARNING: The backlight contains mercury. Caution should be exercised when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. 18. Slide the backlight out of the backlight frame. Removing the Backlight C–12 Maintenance and Service Guide...
Page 237 19. Disconnect the display cable 1 from the LCD panel. 20. Remove the screws 2 that secure the LCD panel to the display rear panel. 21. Release the LCD panel 3 from the display rear panel. 22. Release the tape 4 that secures the LCD panel to the display rear panel.
Page 238 Display Component Recycling 23. Remove the LCD panel. Removing the LCD Panel 24. Recycle the LCD panel and backlight. C–14 Maintenance and Service Guide...
Page 239: Connector Pin Assignments
Connector Pin Assignments Signal Audio out, left channel Audio out, right channel Maintenance and Service Guide Table D-1 Audio-Out (Headphone) Signal Ground D–1...
Page 240: Universal Serial Bus
Connector Pin Assignments Signal Audio signal in Audio signal in Signal +5 VDC Data – D–2 Table D-2 Audio-In (Microphone) Table D-3 Universal Serial Bus Signal Ground Signal Data + Ground Maintenance and Service Guide...
Page 241 Signal S-VHS color (C) signal Composite video signal S-VHS intensity (Y) signal S-VHS color ground Maintenance and Service Guide Connector Pin Assignments Table D-4 S-Video-Out Signal TV-CD S-VHS intensity ground Composite video ground D–3...
Page 242: External Monitor
Connector Pin Assignments Signal Red analog Green analog Blue analog Not connected Ground Ground analog Ground analog Ground analog D–4 Table D-5 External Monitor Signal +5 VDC Ground Monitor detect DDC 2B data Horizontal sync Vertical sync DDC 2B clock Maintenance and Service Guide...
Page 243 Signal Unused Ring Maintenance and Service Guide Table D-6 RJ-11 (Modem) Signal Unused Unused Unused Connector Pin Assignments D–5...
Page 244 Connector Pin Assignments Signal Transmit + Transmit – Receive + Unused D–6 Table D-7 RJ-45 (Network) Signal Unused Receive – Unused Unused Maintenance and Service Guide...
Page 245: Power Cord Set Requirements
Power Cord Set Requirements 3-Conductor Power Cord Set The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120 or 220 to 240 volts AC. The power cord set included with the computer meets the requirements for use in the country where the equipment is purchased.
Page 246: General Requirements
Power Cord Set Requirements General Requirements The requirements listed below are applicable to all countries. ■ The length of the power cord set must be at least 1.5 m (5.0 ft) and a maximum of 2.0 m (6.5 ft). ■ All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the country where the power cord set will be used.
Page 247 Country-Specific Requirements 3-Conductor Power Cord Set Requirements Country/Region Australia Austria Belgium Canada Denmark Finland France Germany Italy Japan ✎ NOTES: 1. The flexible cord must be <HAR> Type HO5VV-F, 3-conductor, 1.0 mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country where it will be used.
Page 248 Power Cord Set Requirements 3-Conductor Power Cord Set Requirements (Continued) Country/Region Korea The Netherlands Norway People’s Republic of China Sweden Switzerland Taiwan United Kingdom United States ✎ NOTES: 1. The flexible cord must be <HAR> Type HO5VV-F, 3-conductor, 1.0 mm² conductor size.
Page 249 AC adapter, spare part numbers 3–22 accessory battery connector 1–22 arrow keys 1–15 audio cable illustrated 3–20 removal 5–71 audio troubleshooting 2–21 audio-in jack location 1–11 pin assignments D–2 audio-out jack location 1–11 pin assignments D–1 base enclosure, spare part number 3–7 battery removal 5–6...
Page 250 Index left-side 1–10 rear 1–10 right-side 1–8 top 1–16 computer feet illustrated 3–19 locations 5–11 Computer Setup Advanced Menu 2–5 Diagnostics Menu 2–4 File Menu 2–2 overview 2–1 Security Menu 2–3 computer specifications 6–1 connector pin assignments audio-in D–2 audio-out D–1 external monitor D–4 headphone D–1 microphone D–2...
Page 251 display panel illustrated 3–16 removal 5–52 spare part numbers 3–17 3–30 5–48 display release button 1–7 Display Rubber Kit, spare part number 3–30 Display Screw Kit, spare part number 3–17 docking connector 1–22 drive light 1–7 drives, preventing damage 4–3 DVD/CD-RW Combo Drive spare part number 3–28 DVD±RW and CD-RW...
Page 252 1–11 pin assignments D–1 heat sink removal 5–39 spare part numbers 3–7 3–29 3–32 HP Docking Station, spare part number 3–22 HP Extended Life Battery, spare part number 3–22 3–25 Index–4 I/O address specifications Info Center button 1–17 infrared port 1–7...
Page 253 memory module compartment cover illustrated 3–19 removal 5–15 microphone removal 5–66 spare part number 3–5 3–30 5–66 microphone jack location 1–11 pin assignments D–2 Mini Card compartment 1–23 Mini Card module compartment cover illustrated 3–19 removal 5–19 Mini Card WLAN module removal 5–17 spare part numbers 3–11 3–13...
Page 254 Index PC Card slot bezel, illustrated 3–19 PC Card slots 1–11 PC Card/digital media board removal 5–61 spare part number 3–5 3–29 5–61 plastic parts 4–2 Plastics Kit contents 3–19 spare part number 3–5 3–19 3–29 pointing device, troubleshooting 2–25 pointing stick 1–21 pointing stick buttons 1–21 pointing stick cable, illustrated...
Page 255 specifications computer 6–1 DVD±RW and CD-RW Combo Drive 6–5 DVD-ROM drive 6–7 hard drive 6–4 I/O addresses 6–11 interrupts 6–9 memory map 6–14 optical drive 6–5 system DMA 6–8 static shielding materials 4–8 stringent security 1–4 S-Video-out jack location 1–13 pin assignments D–3 switch cover removal 5–35...
Page 256 Index vents 1–23 video troubleshooting 2–12 volume buttons 1–17 Windows applications key 1–15 Windows logo key 1–15 wireless antenna illustrated 3–16 removal 5–54 Wireless Antenna Kit, spare part number 3–17 5–48 5–54 wireless button 1–17 wireless light 1–6 workstation precautions 4–6 Index–8 3–30 1–17...

HP Compaq nc6400 Maintenance And Service Manual

Table of Contents

1 Product Description

2 Troubleshooting

3 Illustrated Parts Catalog

Table 3-2 Display Assembly Components Spare Part Number Information

4 Removal and Replacement Preliminaries

5 Removal and Replacement Procedures

Quick Links

Chapters

Troubleshooting

Related Manuals for HP Compaq nc6400

Summary of Contents for HP Compaq nc6400

Table of Contents