Advertisement
O
'
M
peratOr
s
anual
Triple Rear Bagger — 19A40002100
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Printed In USA
Form No. 769-04626C
(February 24, 2010)
Advertisement
Related Manuals for Cub Cadet 19A40002100
Summary of Contents for Cub Cadet 19A40002100
- Page 1 READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 Printed In USA Form No. 769-04626C...
-
Page 2: Table Of Contents
Visit us on the web at www.cubcadet.com ◊ Call a Customer Support Representative at (800) 965-4CUB ◊ Locate your nearest Cub Cadet Dealer at (877) 282-8684 ◊ Write us at Cub Cadet • P.O. Box 361131 • Cleveland, OH • 44136-0019... -
Page 3: Important Safe Operation Practices
Important Safe Operation Practices WARNING! This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. -
Page 4: Safety Symbols
Use slow speed. Choose a low enough speed setting so General Service that you will not have to stop or shift while on the slope. Before cleaning, repairing, or inspecting, make certain the Tires may lose traction on slopes even though the brakes blade(s) and all moving parts have stopped. - Page 5 2 — i ectiOn MpOrtant peratiOn ractices...
-
Page 6: Carton Contents & Hardware Packs
Contents of Carton Before beginning installation, remove all parts from the carton to make sure everything is present. Carton contents are listed below and shown in Fig. 3-1. Three hardware packs are included in this kit and are detailed on the following page. •... -
Page 7: Contents Of Hardware Pack
CONTENTS OF HARDWARE PACK This grass collector kit is shipped with three loose hardware packs enclosed and one set of hardware included in the mounting bracket kit. Please check your hardware packs against the illustrations below. The quantities for each item is listed in parenthesis. Hardware included with 689-00096 Hardware Pack 689-00163 712-04065... -
Page 8: Assembly & Installation
Assembly & Installation NOTE: References to left, right, front and rear of the tractor are from the operator’s position, unless otherwise stated. • Before assembly, place the tractor on a firm, level surface, disengage the PTO, stop the tractor engine and set the parking brake. - Page 9 Note: The clevis pin can be fed down through the hitch plate and secured underneath with the hairpin clip, or it may be easier to feed the clevis pin up through the hitch plate hole and secure with the hairpin clip on the topside. The latter method may be preferred since it can be easier to insert the hairpin clip.
- Page 10 Assembling Remaining Bagger Components Now that the mounting brackets are assembled and are in place on the tractor, follow these steps to assemble the remaining bagger components. Snap the plastic upper chute support in place by first clipping the side portion onto the bagger support rail (1) with the edge of the snap feature aligned with the red line, as seen in the inset of Fig.
- Page 11 Slide the hinge pin into the hole located on the mounting Open Hood by pushing in on the rear, right-side tab with tab, as in Fig. 4-12. Use the cut-out window (See inset in your right hand, as seen in 1 of Fig. 4-14, and lifting the cover Fig.
- Page 12 Attaching Blades Move the wood block to either the left or right blade for stabilization and remove and replace the center blade so that side of the blade with part number faces the ground WARNING! Always protect your hands while when the mower is in the operating position.
- Page 13 Installing the Chute Discharge Plate NOTE: An extra carriage bolt and lock nut have been supplied in your bagger kit in hardware pack 689-00163. Remove the discharge chute by removing the two flange You may replace the old hardware for the chute stop lock nuts securing it.
- Page 14 Rotate the chute around the deck so that its front edge fits Peel the backing off of the self-adhesive foam strip (721- snugly into the deck opening. Lower the chute deflector 04388) that has been included with your grass collector. slowly (C in Fig.
-
Page 15: Operation
Operation Bagger Usage Remove the grass bags, as shown in Fig. 5-2, by lifting each bag up (1) and moving the bags away from the bag support NOTE: When all of the grass bags are full, place the tractor on a assembly (2). -
Page 16: Parts List
19A40002100 Parts List... - Page 17 Ref. Part Number Description 931-04291 Upper Chute Assembly 931-04298 Triple Bagger Cover Assembly 731-06497 Upper Chute Support 731-06504 Bagger Cover Screen 710-0276 Carriage Screw, 5/16-18 x 1.00” 710-3008 Hex Head Screw, 5/16-18 x .75” 711-0309A Clevis Pin, .62” Dia. 964-04090A Grass-bag Assembly 683-04498A Triple Bag Support Assembly...
- Page 18 Notes...
-
Page 20: Warranty
Service completed by someone other than an authorized service The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased or leased and used in the United dealer.