TP-Link TD-8817 User Manual
  1. Manuals
  2. Brands
  3. TP-Link Manuals
  4. Network Router
  5. TD-8817
  6. User manual
TP-Link TD-8817 User Manual

TP-Link TD-8817 User Manual

Adsl2+ ethernet/usb modem router
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
TD-8817
ADSL2+ Ethernet/USB Modem Router
Rev: 3.0.0
1910010897

Advertisement

Table of Contents
loading

Related Manuals for TP-Link TD-8817

Summary of Contents for TP-Link TD-8817

  • Page 1 TD-8817 ADSL2+ Ethernet/USB Modem Router Rev: 3.0.0 1910010897...
  • Page 2 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.

  • Page 3: Fcc Statement

    FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

  • Page 4: Safety Information

    Safety Information When product has power button, the power button is one of the way to shut off the product;  when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. Don’t disassemble the product, or make repairs yourself.

  • Page 5: Declaration Of Conformity

    DECLARATION OF CONFORMITY For the following equipment: Product Description: ADSL2+ Ethernet/USB Modem Router Model No.: TD-8817 Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives: Directives 2004 / 108 / EC, Directives 2006 / 95 / EC, Directives 2011/65/EU The above product is in conformity with the following standards or other normative documents：...

  • Page 6: Table Of Contents

    CONTENTS Package Contents ....................1 Chapter 1. Introduction ..................2 Product Overview ...................... 2 Main Features ......................2 Conventions ......................3 Chapter 2. Hardware Installation ................. 4 The Front Panel ......................4 The Back Panel......................5 Installation Environment .................... 5 Hardware Installation Procedures ................
  • Page 7 4.5.6 CWMP ..........................52 Maintenance......................52 4.6.1 Administration.........................53 4.6.2 Time Zone ........................53 4.6.3 Firmware.........................55 4.6.4 SysRestart........................57 4.6.5 Diagnostics........................57 Help......................... 57 Appendix A: Specifications................... 59 Appendix B: Configuring the PC................60 Appendix C: Troubleshooting................64 Appendix D: Technical Support ................67...

  • Page 8: Package Contents

    ADSL2+ Ethernet/USB Modem Router User Guide Package Contents The following items should be found in your package:  One TD-8817 ADSL2+ Ethernet/USB Modem Router  One Power Adapter for TD-8817 ADSL2+ Ethernet/USB Modem Router  Quick Installation Guide  One RJ45 cable ...

  • Page 9: Chapter 1. Introduction

    The device is designed to provide a simple and cost-effective ADSL Internet connection for a private Ethernet network. TD-8817 connects to an Ethernet LAN or computers via standard Ethernet ports. The ADSL connection is made using ordinary telephone line with standard connectors. Multiple workstations can be networked and connected to the Internet using a single Wide Area Network (WAN) interface and single global IP address.

  • Page 10: Conventions

    Supports firmware upgrade and Web management.  1.3 Conventions The Router or device mentioned in this User Guide stands for TD-8817 without any explanations. Parameters provided in the pictures are just references for setting up the product, which may differ from the actual situation.

  • Page 11: Chapter 2. Hardware Installation

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Chapter 2. Hardware Installation 2.1 The Front Panel Figure 2-1 The LEDs are located on the front panel, they indicate the device’s working status. For details, please refer to LED Explanation. LED Explanation:...

  • Page 12: The Back Panel

    Make sure the cables and power cord are placed safely out of the way so they do not create a tripping hazard.  The modem router can be placed on a shelf or desktop. Generally, TD-8817 is placed on a horizontal surface. The device also can be mounted on the wall as shown in Figure 2-3.

  • Page 13: Hardware Installation Procedures

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 2-3  Note: The diameter of the screw, 4mm<D<7.5mm, and the distance of two screws is 111.5mm. The screw that project from the wall need around 4mm based, and the length of the screw need to be at least 20mm to withstand the weight of the product.
  • Page 14 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 2-4...

  • Page 15: Chapter 3. Quick Installation Guide

    Chapter 3. Quick Installation Guide 3.1 TCP/IP Configuration The default IP address of the TD-8817 ADSL2+ Ethernet/USB Modem Router is 192.168.1.1. And the default Subnet Mask is 255.255.255.0. These values can be changed as you desire. In this guide, we use all the default values for description.

  • Page 16: Usb Configuration

    CD into your CD-ROM drive. The autorun.exe will automatically run and click Browse CD to read the files on the CD. Click the file TD-8817>USB Driver and select the USB driver type according to the operating system of your computer to start installation.
  • Page 17 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 3-3 Step 3: You will see Figure 3-4 as follow, please wait a moment. Figure 3-4 Step 4: After that, you will see Figure 3-5. Click Finish to complete the installation.

  • Page 18: Login

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 3-5  Note: All of the above settings are under windows XP. If you want to pull out the USB device you must disconnect the network of USB first. In the Vista operating system, maybe the “Unknown Device” screen will pop up when you insert the USB cable of the Router to a computer, please just unplug the USB cable and try again.
  • Page 19 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 3-6 Step 1: Select the Quick Start tab, then click RUN WIZARD, and you will see Figure 3-7. Click the NEXT button. Figure 3-7 Step 2: Configure the time for the Router, and then click the NEXT button.
  • Page 20 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 3-9 Step 4: Configure the following options provided by your ISP: Username, Password, VPI, VCI and Connection Type. Then click NEXT. Figure 3-10 Step 5: Click NEXT to finish the Quick Start.

  • Page 21: Chapter 4. Software Configuration

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Chapter 4. Software Configuration This User Guide recommends using the “Quick Installation Guide” for first-time installation. For advanced users, if you want to know more about this device and make use of its functions adequately, maybe you will get help from this chapter to configure the advanced settings through the Web-based Utility.

  • Page 22: System Log

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 4-2 4.1.2 System Log Choose “Status→System Log” menu, and you will be able to query the logs of the Router.

  • Page 23: Statistics

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 4-3 The modem router can keep logs of all traffic. You can query the logs to find what happened to the modem router. Click the CLEAR LOG button to clear the logs.
  • Page 24 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide  Interface: You can select Ethernet and ADSL to view the corresponding network traffic over different ports.  Select Ethernet, and you will see the statistics table as below. Statistics Table: Transmit Frames The frames transmitted over the Ethernet port.

  • Page 25: Quick Start

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 4.2 Quick Start Please refer to Login. 4.3 Interface Setup Choose “Interface Setup”, you can see the next submenus: Internet and LAN. Figure 4-5 Click any of them, and you will be able to configure the corresponding function.
  • Page 26 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 4-6  ATM VC: ATM settings are used to connect to your ISP. Your ISP provides VPI (Virtual Path Identifier), VCI (Virtual Channel Identifier) settings to you. In this Device, you can totally setup 8 VCs on different encapsulations, if you apply 8 different virtual circuits from your ISP.
  • Page 27 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide  Virtual Circuit: Select the VC number you want to setup, PVC0~PVC7.  Status: If you want to use a designed VC, you should activate it.  VPI: Identifies the virtual path between endpoints in an ATM network. The valid range is from 0 to 255.
  • Page 28 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 4-7  Encapsulation: Select the encapsulation mode for the Dynamic IP Address, you can leave it default.  Bridge Interface: Activate the option, the modem router can also work in Bridge mode.
  • Page 29 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Static IP Address Select this option if your ISP provides static IP information for you. You should set static IP address, IP Subnet Mask, and Gateway address in the screen below (shown in Figure 4-12).
  • Page 30 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 4-9  Service name: Specify a name for the PPPoA/PPPoE connection for recognition.  Username: Enter your username for your PPPoA/PPPoE connection to identify and verify your account to the ISP. ...
  • Page 31 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide or given by your ISP. For Static IP, you need to specify the IP address, Subnet Mask and Gateway IP address.  Dual Stack Lite: Enable the Dual Stack Lite (D-S Lite) function if you need. It is disabled by default.
  • Page 32 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 4-11  IP Common Option: Configure the IP common option here.  Encapsulation: Select the encapsulation mode for the Dynamic IP Address, you can leave it default.  Bridge Interface: Activate the option, the modem router can also work in Bridge mode.
  • Page 33 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 4-12  Note: Each IP address entered in the fields must be in the appropriate IPv6 form, which is eight IP octets separated by a colon (x:x:x:x:x:x:x:x). The modem router will not accept the IP address if it is not in this format.
  • Page 34 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 4-13  Service name: Specify a name for the PPPoA/PPPoE connection for recognition.  Username: Enter your username for your PPPoA/PPPoE connection to identify and verify your account to the ISP. ...

  • Page 35: Lan

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide enable the function, please click Enable.  MLD Proxy: The MLD (Multicast Listener Discovery Protocol) Proxy function is disabled by default. If you want to enable the function, please click Enable.  Dual Stack Lite: Enable the Dual Stack Lite (D-S Lite) function if you need. It is disabled by default.
  • Page 36 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 4-15  Router Local IP: These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed.
  • Page 37 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide means the ADSL modem router will only send but will not accept RIP packet.  Multicast: Select IGMP version, or disable the function. IGMP (Internet Group Multicast Protocol) is a session-layer protocol used to establish membership in a multicast group.
  • Page 38 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide  Primary DNS Server: Type in your preferred DNS server.  Secondary DNS Server: Type in your preferred DNS server.  Note: If Use Auto Discovered DNS Server Only is selected in DNS Relay, this router will accept the first received DNS assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s) during the connection establishment.

  • Page 39: Advanced Setup

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 4.4 Advanced Setup Choose “Advanced Setup”, you can see the next submenus: Figure 4-18 Click any of them, and you will be able to configure the corresponding function. 4.4.1 Firewall Choose “Advanced Setup→Firewall” menu, and you will see the next screen (shown in Figure 4-19).

  • Page 40: Nat

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Click ADD ROUTE button to add a new route in the next screen (shown in Figure 4-21). Figure 4-21  Destination IP Address: This parameter specifies the IP network address of the final destination.
  • Page 41 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide  Virtual Circuit: Enter Virtual Circuit Index that you plan to setup for the NAT function.  NAT Status: This field shows the current status of the NAT function for the current VC. You can go to the previous screen (shown in Figure 4-6) to activate the function.
  • Page 42 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 4-24  Rule Index: The Virtual server rule index for this VC. You can specify 10 rules in maximum. All the VCs with single IP will use the same Virtual Server rules.
  • Page 43 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Other operations for the entries are as follows: Enter the index of assigned entry, click the DELETE button to delete the entry. Click the BACK button to return to the previous screen. Click the CANCEL button to cancel the configuration which is made just now.

  • Page 44: Qos

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide  Address Mapping List: This displays the inform ation about the Mapping addresses. To add a mapping rule: Step 1: Select the “Virtual Circuit” and Multiple for the “Number of IPs”. Then select the tab IP Address Mapping (shown in Figure 4-25).
  • Page 45 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 4-27 QoS: Select this option to Activate/Deactivate the IP QoS on different types.   Summary: Click the button to view the configurations of QoS.  Rule: Configure the rules for QoS. If the traffic complies with the rule, then the Router will take the corresponding action to deal with it.
  • Page 46 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide application.  Vlan ID Range: Enter the Vlan range, then the rule will be effective to the selected Vlans.  IPP/DS Field: Select the type of the action to assign the priority. When you select IPP/TOS, you can assign the priority via IP information. IP QoS function is intended to deliver guaranteed as well as differentiated Internet services by giving network resource and usage control to the Network operator.

  • Page 47: Vlan

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide  Rule: Configure the rules for QoS. If the tra ffic complies with the rule, then the Router will take the corresponding action to deal with it.  Rule Index: Select the index for the rule you want to configure.
  • Page 48 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 4-30  VLAN Index: Select the VLAN index for this VC. You can specify 8 groups in maximum.  VLAN ID: This indicates the VLAN group.  ATM VCs: Select the ATM VCs as members of VLAN, and if you leave the Tagged blank, the tag in frames will be deleted when transmitted from the VC.

  • Page 49: Adsl

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 4-31  PVID: Each physical port has a default VID called PVID (Port VID). PVID is assigned to untagged frames or priority tagged frames (frames with null (0) VID) received on this port.

  • Page 50: Access Management

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 4.5 Access Management Choose “Access Management”, you can see the next submenus: Figure 4-33 Click any of them, and you will be able to configure the corresponding function. 4.5.1 ACL Choose “Access Management→ACL”, you can see the next screen (shown in Figure 4-34). You can specify the client to access the ADSL modem router once setting his IP as a Secure IP Address through selected applications.

  • Page 51: Filter

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 4.5.2 Filter Choose “Access Management→Filter”, you can see the Filter screen (the default is IP/MAC Filter screen shown in Figure 4-35). The filtering feature includes IP/MAC Filter, Application Filter, URL Filter. The feature makes it possible for administrators to control user's access to the Internet, protect the networks.
  • Page 52 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide  Note: If select PVC0~PVC7 as a interface, the filter will match the IP traffic of WAN port with specified IPs (Source IP Address and Destination IP Address), If select LAN as a interface, the filter will match the IP traffic of LAN port with specified IPs.
  • Page 53 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Step 2: Select the IP/MAC Filter Set Index and IP/MAC Filter Rule Index for the rule, then select the Interface “PVC0”, and select the Direction “Both” for the first rule.  Note: If you want to make the rule take effect, please select Yes to active the rule.
  • Page 54 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Other operation for the entries as shown in Figure 4-35: Select the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to view or modify the entry. Select the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to locate the specific rule, and then click the DELETE button to delete the entry.
  • Page 55 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Step 1: Select the “IP/MAC Filter” as the Filer Type Selection: Select the “MAC” as the Rule Type on the Filter screen (show in Figure 4-36). , Then you can configure the specific rule for the example.
  • Page 56 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 4-37  Filter Type Selection: Select the Application Filter for the next configuration.  Application Filter: Activate or deactivate the function.  ICQ & MSN & YMSG & Real Audio/Video: Select Allow or Deny for these applications. If you select Allow, the modem router will accept the application;...

  • Page 57: Snmp

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide  Filter Type Selection: Select the URL Filter for the next configuration.  Active: Select “Yes” to make the rule to take effect.  URL Index: Select the index for the URL Filter entry.

  • Page 58: Ddns

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide simple peer-to-peer network connectivity between devices. An UPnP device can dynamically join a network, obtain an IP address, convey its capabilities and learn about other devices on the network. In turn, a device can leave a network smoothly and automatically when it is no longer in use.

  • Page 59: Cwmp

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 4.5.6 CWMP Choose “Access Management→CWMP”, you can configure the CWMP function in the screen (shown in Figure 4-42). The modem router offers CWMP feature. The function supports TR-069 protocol which collects information, diagnoses the devices and configures the devices automatically via ACS (Auto-Configuration Server).

  • Page 60: Administration

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 4.6.1 Administration Choose “Maintenance→Administration”, you can set new password for admin in the screen (shown in Figure 4-44). Figure 4-44  Note: There is only one account that can access Web-Management interface. The default account is "admin", and the password is "admin".
  • Page 61 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 4-45  Note: The ADSL modem router built-in some NTP Servers, when the modem router connects to the Internet, the modem router will get the system time automatically from the NTP Server. You can also configure the NTP Server address manually, and then the modem router will get the time from the specific Server firstly.

  • Page 62: Firmware

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure 4-47 4.6.3 Firmware Choose “Maintenance→Firmware”, you can upgrade the firmware of the modem router in the screen (shown in Figure 4-48). Make sure the firmware or romfile you want to use is on the local hard drive of the computer.
  • Page 63 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide recent firmware version, unless the version has a new feature that you want to use. When you upgrade the modem router 's firmware, you may lose its current configurations, so please back up the modem router’s current settings before you upgrade its firmware.

  • Page 64: Sysrestart

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Step 2: Click the UPGRADE button to complete. 4.6.4 SysRestart Choose “Maintenance→SysRestart”, you can select to restart the device with current settings or restore to factory default settings in the screen (shown in Figure 4-51).

  • Page 65: Help

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide 4.7 Help Choose “Help”, you can view the help information for configuration of any function. Figure 4-53  Note: Click the tab, and you will be able to get the corresponding information.

  • Page 66: Appendix A: Specifications

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Appendix A: Specifications General ANSI T1.413, ITU G.992.1, ITU G.992.2, ITU G.992.3, ITU G.992.5 Standards and Protocols IEEE 802.3, IEEE 802.3u, TCP/IP, PPPoA , PPPoE, SNTP, HTTP, DHCP, ICMP, NAT,CWMP Safety & Emission FCC, CE 1 10/100M Auto-Negotiation RJ45 port（Auto MDI/MDIX)

  • Page 67: Appendix B: Configuring The Pc

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Appendix B: Configuring the PC In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows XP. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if necessary.
  • Page 68 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure B-2 The following TCP/IP Properties window will display and the IP Address tab is open on this window by default. Now you have two ways to configure the TCP/IP protocol below:  Setting IP address automatically...
  • Page 69 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure B-3  Note: For Windows 98 OS or before, the PC and modem router may need to be restarted.  Setting IP address manually Select Use the following IP address radio button. And the following items available If the modem router's LAN IP address is 192.168.1.1, specify the IP address as 192.168.1.x...
  • Page 70 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Figure B-4 Now: Click OK to keep your settings.

  • Page 71: Appendix C: Troubleshooting

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Appendix C: Troubleshooting T1. How do I restore my modem router’s configuration to its factory default settings? With the modem router powered on, press and hold the RESET button on the rear panel for 8 to 10 seconds before releasing it.
  • Page 72 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Select Obtain an IP address automatically and Obtain DNS server address automatically. Then click OK. For Windows 8 Move your mouse to the lower right corner and you will see Search icon in the Popups.
  • Page 73 TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Now, try to log on to the Web-based configuration page again after the above settings have been configured. If you still cannot access the configuration page, please restore your modem router’s factory default settings and reconfigure your modem router following the instructions in Login.

  • Page 74: Appendix D: Technical Support

    TD-8817 ADSL2+ Ethernet/USB Modem Router User Guide Appendix D: Technical Support Appendix D: Technical Support Technical Support Technical Support For more troubleshooting help, go to: For more troubleshooting help, go to:   www.tp-link.com/en/support/faq www.tp-link.com/en/support/faq   To download the latest Firmware, Driver, Utility and User Guide, go to: To download the latest Firmware, Driver, Utility and User Guide, go to: www.tp-link.com/en/support/download...

Table of Contents