TABLE OF CONTENTS FOR YOUR SAFETY -------------------------------------------------- 1 SAFETY PRECAUTIONS -------------------------------------- 2 SPECIAL NOTES ON LCD MONITORS ------------------- 3 BEFORE YOU OPERATE THE MONITOR --------------------- 3 FEATURES -------------------------------------------------------- 3 PACKING LIST --------------------------------------------------- 3 INSTALLATION INSTRUCTIONS --------------------------- 4 CONTROLS AND CONNECTORS -------------------------- 5 ADJUSTING THE VIEWING ANGLE ----------------------- 6 OPERATING INSTRUCTIONS ------------------------------------- 7 GENERAL INSTRUCTIONS ---------------------------------- 7...
Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PRECAUTIONS Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance.
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears.
INSTALLATION INSTRUCTIONS SWIVEL BASE Install Remove Figure 1 Installing and Removing the Swivel Base POWER CORD Power Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.) 3.
CONTROLS AND CONNECTORS SIGNAL CABLE Connecting the Signal Cable: Plug the Signal Cable one end to LCD monitor’s “DSUB-Input” socket, the other end to the computer's VGA port and tighten the two screws on the cable connector. Connecting the Power Cord: Plug the AC-power cord into the External Adapter. Then plug the DC-jack power cable into DC-IN Inlet.
ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor’s angle.
OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the side of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. •...
FRONT PANEL CONTROL • Power Button Press this button to switch ON/OFF of monitor’s power. • Power Indicator: Green — Power On mode. Orange —Off mode. • MENU / ENTER : Active OSD menu or function adjust confirm or Exit OSD menu when in Contrast /Brightness OSD status.
HOW TO ADJUST A SETTING Press the MENU-button to activate the OSD window (Figure 5). Press < or > to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it. If the function selected has a sub-menu, press <...
ADJUSTING THE PICTURE The descriptions for function control LEDS Main Main Menu Menu Description Menu Item Menu Icon Item Brightn Backlight Adjustment Contra Contrast from Digital-register. Standard Standard Mode Text Text Mode Internet Internet Mode Game Game Mode Luminance Movie Movie Mode Sports Sports Mode Gamma1 Adjust to Gamma1...
Page 13
Main Main Menu Menu Description Menu Item Menu Icon Item Adjust picture Clock to reduce Clock Vertical-Line noise. Adjust Picture Phase to reduce Focus Horizontal-Line noise Image Setup H.Posit Adjust the verticalposition of the picture. V.Positi Adjust the horizontal position of the picture.
Page 14
Main Main Menu Menu Description Menu Item Menu Icon Item Full Disable or Enable Full Enhance on or off Enhance Mode Nature Disable or Enable Nature Skin on or off Skin Mode Green Disable or Enable Green Field on or off Color Field Mode...
Page 15
Main Main Menu Menu Description Menu Item Menu Icon Item Adjust the verticalposition of H.Position Adjust the horizontal position of V.Position Timeout Adjust the OSD Timeout Setup Transpare Adjust the transparence of OSD Language Select the OSD language Select to Auto Detect input Auto signal Input...
Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.
TECHNICAL SUPPORT (FAQ) Problem & Question Possible Solution *Check if the Power Switch is in the ON Power LED is not on position *Power Cord should be connected *Check if the PC system is Plug & Play compatible *Check if the Video Card is Plug & Play No Plug &...
Page 18
FOCUS adjusts the phase of the pixel clock signal. With a wrong phase adjustment the picture has horizontal disturbances in light picture. For FOCUS and CLOCK adjustment use “dot-pattern” or Win 95/98 shut-down mode pattern .
ERROR MESSAGE & POSSIBLE SOLUTION NO SIGNAL Check that the signal-cable is properly connected , If the connector is loose, tighten the connector’s screws. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORT Your computer has been set to unsuitable display mode ,set the computer to display mode given in the following table.
ISO 14001 Certification ISO 14001 certification is the pattern of certification of the environmental management system, is the core standard of ISO14000 series of standard on environmental management.