1. Manuals
  2. Brands
  3. Dovre Manuals
  4. Stove
  5. SAPPHIRE DV425TR
  6. Owner's manual and installation instructions

Dovre SAPPHIRE DV425TR Owner's Manual And Installation Instructions

Direct vent room heater
Hide thumbs
Table of Contents

Advertisement

Quick Links

Quartet Front
WARNING!
If the information in this Manual is not fol-
lowed exactly, a fire or explosion may result
causing property damage, personal injury or
loss of life.
-Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
-WHAT TO DO IF YOU SMELL GAS
•
Do not try to light any appliance.
•
Do not touch any electrical switch; do not use any
phone in your building.
•
Immediately call your gas supplier from a neigh-
bor's phone. Follow the gas supplier's instruc-
tions.
•
If you cannot reach your gas supplier, call the fire
department.
-Installation and service must be performed by a qual-
ified installer, service agency or the gas supplier.
FOR YOUR SAFETY
The appliance area must be kept clear and free
from combustible materials, gasoline and other
flammable vapors and liquids.
1445 North HIghway
Colville, WA 99114
SAPPHIRE DV425TR
DIRECT VENT ROOM HEATER
OWNER'S MANUAL
AND INSTALLATION INSTRUCTIONS
(FRONTS SOLD SEPARATELY)
This Manual must be used for installation of the
DV425TR Gas-Fired Room Heater and retained by the
homeowner for operating and maintenance instructions.
A Division of Hearth Technologies Inc.
#250-5533
WARNING!
Improper installation, adjustment, alteration,
service or maintenance can cause injury or
property damage. Refer to this Manual. For
assistance or additional information, consult
a qualified installer, service agency or the
gas supplier.
This Heater may be installed with a Vertical
or Horizontal Direct Vent Termination System.
This appliance may be installed in an aftermarket,
permanently located, Manufactured (Mobile) Home,
where not prohibited by Local Codes.
This appliance is only for use with the type of fuel
indicated on the Rating Plate. This appliance is not
convertible for use with other gases, unless a certi-
fied Conversion Kit is used.
02/2001
Solitaire Front
Tested and
O-T L
Oregon USA
Listed by
C
OMNI-Test Laboratories, Inc.
addinhearth.com
ahpfireup.com
Beaverton

Advertisement

Table of Contents
loading

Related Manuals for Dovre SAPPHIRE DV425TR

Summary of Contents for Dovre SAPPHIRE DV425TR

  • Page 1 SAPPHIRE DV425TR DIRECT VENT ROOM HEATER OWNER’S MANUAL AND INSTALLATION INSTRUCTIONS Solitaire Front Quartet Front (FRONTS SOLD SEPARATELY) WARNING! WARNING! If the information in this Manual is not fol- Improper installation, adjustment, alteration, lowed exactly, a fire or explosion may result...

  • Page 2: Table Of Contents

    Maintenance ..........................51 Yearly Maintenance........................52 Blower Electrical Wiring ........................ 53 Troubleshooting ........................54 Parts & Accessories ....................... 57 Warranty............................ 60 DOVRE® is a registered trademark of Aladdin Hearth Products, a Division of Hearth Technologies Inc. 02/01 Page 2 250-5533...

  • Page 3: Listings And Code Approvals

    DV425TR DIRECT VENT ROOM HEATER LISTINGS AND CODE APPROVALS The Dovre DV425TR Direct Vent Gas Appliance is listed to ANSI standard Z21.88(b)-1999/CSA 2.33b-M99 Vented Gas Fireplace Heaters and applicable sections of UL307b Gas Burning Heating Appliances for Manufactured Homes and Recreational Vehicles, CAN/CGA 2.17-M91 "Gas Fired Appliances for use at High Altitudes,"...

  • Page 4: Serial Label

    DV425TR DIRECT VENT ROOM HEATER SERIAL LABEL (Located on back of stove) MODEL / MODÈLE: DV425 T/R SERIAL NO. VENTED GAS FIREPLACE HEATER FOURNAISE AU GAZ AVEC VENTILATION 1445 North HIghway NOT FOR USE WITH SOLID FUEL / Report No. / Rapport Numéro Colville, WA 99114 NE PAS UTILISER AVEC LE COMBUSTIBLE SOLIDE 061-S-19-5...

  • Page 5: Safety Notices

    DV425TR DIRECT VENT ROOM HEATER SAFETY NOTICES Due to high temperatures, the appliance should be located Accessories page of this manual for replacement. out of traffic and away from furniture and draperies. Instruct everyone in the house how to shut off the gas to the appliance and also at the main gas shut-off valve.

  • Page 6: Overview Of Installation

    DV425TR DIRECT VENT ROOM HEATER OVERVIEW OF INSTALLATION TO OPERATION • Familiarize yourself with this Owner's Manual and the Safety Notices located in this manual, and posted on the heater. • Remove and unpack the following components: Beneath the stove: 5 Logs, grill, grill cover*, and 4 cap speed nuts. Shrink-wrapped to front of unit: Owner's Manual, mineral wool, lava rock, and flex line.

  • Page 7: Dimensions

    DV425TR DIRECT VENT ROOM HEATER DIMENSIONS DOVRE 425 T/R Dimensions 17-1/2" 14-3/8" 8" 21-1/2" 14-5/8" NOTE: Diagrams show heater equipped with optional Blower, part #844-9030. 21-1/2" Rear Vent 28-5/8" 22-1/4" 8" 22-1/8" 14-5/8" NOTE: If heater is equipped with Hearth Legs Kit center-line dimension is reduced by 3".

  • Page 8: Clearances To Combustibles

    DV425TR DIRECT VENT ROOM HEATER CLEARANCES TO COMBUSTIBLES SAPPHIRE MINIMUM CLEARANCES TO COMBUSTIBLES Minimum clearances required from combustible construction. Side of stove top to side wall 6" (152 mm) Rear of stove top to back wall 3" (100 mm) Corner of stove top to side wall 1"...

  • Page 9: Front Options

    DV425TR DIRECT VENT ROOM HEATER FRONT OPTIONS (Sold Separately, refer to page 57 for part numbers.) QUARTET & SOLITAIRE FACE INSTALLATION INSTRUCTIONS Quartet Parts Include: Solitaire Parts Include: (1) Front Face; (2) Hinged (1) Front Face; (1) Bolt Doors; (2) Gold plated button head hinge pins;...

  • Page 10: Rear Vent Conversion Instructions

    DV425TR DIRECT VENT ROOM HEATER REAR VENT CONVERSION INSTRUCTIONS (See Parts & Accessories, page 57 for part number.) TOOLS REQUIRED: Power drill; #2 Phillips bit; 5/32" KIT CONTENTS: Rear vent grill; .096 NG orifice; Allen wrench; 5/8" open end wrench; high-temp sili- .059 LP orifice;...
  • Page 11 DV425TR DIRECT VENT ROOM HEATER REAR VENT CONVERSION INSTRUCTIONS, cont. 7. Re-install inner flue collar on rear of stove with FIG. 6 damper rod pointing up. See Fig. 5 A dab of high temperature silicone on the gasket will help gasket adhere to the unit.
  • Page 12 DV425TR DIRECT VENT ROOM HEATER REAR VENT CONVERSION INSTRUCTIONS, cont. STEP B: REPLACE BURNER ORIFICE FOR FIG. 9 HORIZONTAL VENT CONFIGURATION: 1. Remove front (if installed), glass, and logs (if installed.) 2. Remove log/burner pan: First remove screws then lift the front of pan vertically and slide pan to one side and pull out of firebox.

  • Page 13: Lp Gas Conversion Instructions

    DV425TR DIRECT VENT ROOM HEATER LP CONVERSION INSTRUCTIONS Part #844-9010 TOOLS REQUIRED: Power drill (a 90° handle is KIT CONTENTS: Replacement orifice (fits top helpful); #2 Phillips bit; 5/32" Allen wrench; 5/8" open vent models only); replacement pilot injector. end wrench. FIG.

  • Page 14: Valve Regulator Replacement

    DV425TR DIRECT VENT ROOM HEATER LP CONVERSION, CONT. Valve Regulator Replacement 1. Turn control knob to the OFF position, ensure that gas supply to the valve has been turned off. 2. Using a Torx TH20, or slotted screwdriver, remove the three pressure regulator mounting screws (A), pressure regulator tower (B), and diaphragm (C).

  • Page 15: Logset Installation

    DV425TR DIRECT VENT ROOM HEATER LOGSET INSTALLATION The logset is packed in the components box and consists of the Fig. 2 following: (See Fig. 1) Qty. # in Fig. 1 Rear log - Left Partial Log - Right Partial Log - Left Twig - Right Twig - While breakable, the logs do not become fragile until after the...

  • Page 16: Hearth Legs Installation Instruction

    DV425TR DIRECT VENT ROOM HEATER HEARTH LEGS INSTALLATION BLOWER INSTALLATION, cont. NOTE: HEARTH LEGS CAN NOT BE USED IF A Ensure FIG. 2 BLOWER IS INSTALLED AS THERE WILL NOT BE ENOUGH these CLEARANCE. wires are BEHIND Refer to page 56, Parts & Accessories for specific color part Blower numbers.

  • Page 17: Thermostat Installation/Remote Control

    DV425TR DIRECT VENT ROOM HEATER GRILL COVER INSTALLATION THERMOSTAT INSTALLATION A thermostat may be installed to regulate the 425TR. It is Top grill cover is shipped with the stove and is an optional use important to use a thermostat designed for millivolt operation item.

  • Page 18: General Venting Instructions

    The warranty will be USE FIELD-FABRICATED VENTING COMPONENTS. voided, and serious fire, health, or other safety hazards The Dovre DV425TR is approved to be vented either may result from any of the following actions: Installation horizontally, through the side wall, or vertically, through of any damaged venting component, unauthorized the roof.

  • Page 19: Installation Methods & Notes

    DV425TR DIRECT VENT ROOM HEATER INSTALLATION METHODS & NOTES Four types of direct vent system installations are determining the position of the stove, be sure to approved for use with the DV425TR. adhere to minimum clearance to combustibles to the 1.

  • Page 20: Simpson-Duravent Parts List

    DV425TR DIRECT VENT ROOM HEATER SIMPSON DURA-VENT PARTS LIST Simpson Dura-Vent offers a complete line of component parts for installation in both horizontal and vertical applications. Many items are offered in decorative black, as well as a galvanized finish. The galvanized pipe and fittings are used for concealed locations such as attics, or spaces where corrosion is a factor, such as above the roofline.
  • Page 21 DV425TR DIRECT VENT ROOM HEATER HTI VENTING PARTS LIST, cont. HTI COMPONENT # Venting System Components Description HHW2 Horizontal High Wind Cap (recommended for optimal performance) HHW2K Horizontal Kit (One 90 Black Elbow, Wall Thimble, 24” Black Pipe, 11” - 14-5/8” Adjustable Vent, HHW2 Termination Cap) RHVK Snorkle Kit #844-8920 (with Dura-Vent part #'s 911B and 940)

  • Page 22: Installation Methods

    DV425TR DIRECT VENT ROOM HEATER INSTALLATION METHODS FIG. 1 - HORIZONTAL TERMINATION Refer to pages 26-31 for installation instructions and requirements. Type A - Up & Out 90 DEG. ELBOW Installations for Top Vent Configurations HHW2 - Recommended for PIPE LENGTH optimum performance.
  • Page 23 DV425TR DIRECT VENT ROOM HEATER INSTALLATION METHODS, cont. FIG. 2 - VERTICAL TERMINATION Refer to pages 32-37 for installation instructions and requirements. VERTICAL TERMINATION On vertical terminations use only Dura-vent Part #991. STORM COLLAR FLASHING FIRESTOP SUPPORT PIPE LENGTH 02/01 Page 23 250-5533...
  • Page 24 DV425TR DIRECT VENT ROOM HEATER INSTALLATION METHODS, cont. FIG. 3 - CLASS A METAL CHIMNEY (USA only) Refer to pages 38-39 for installation instructions and requirements. TERMINATION PART #991 ADAPTOR FLASHING EXISTING METAL CHIMNEY SYSTEM 4" FLEX PIPE RETRO CONNECTOR DIRECT VENT PIPE 02/01...
  • Page 25 DV425TR DIRECT VENT ROOM HEATER INSTALLATION METHODS, cont. FIG. 4 - A & B INTO A MASONRY CHIMNEY (USA only) Refer to pages 40-43 for installation instructions and requirements. Type B - Hearth Rear Vent Installations for Use Type A - Up & Out Installations With Rear Vent Kit (see Parts &...

  • Page 26: Termination Requirements

    DV425TR DIRECT VENT ROOM HEATER HORIZONTAL TERMINATION REQUIREMENTS A. *12” (30cm) minimum: Clearance above grade, veranda, porch, deck, or balcony. B. *12” (30cm) minimum: Clearance to window or door that may be opened. C. 12” (30cm) minimum: Clearance to permanently closed window (recommended to prevent condensation on window. D.

  • Page 27: Vent Graph

    DV425TR DIRECT VENT ROOM HEATER HORIZONTAL INSTALLATION VENT GRAPH Measure the distance from the top of stove to the center of the 90° elbow. On the graph below, draw a horizontal line from that measurement on the vertical axis across until it intersects with the slanted line. From the point of this intersection, draw a vertical line to the bottom of the graph.
  • Page 28 DV425TR DIRECT VENT ROOM HEATER HORIZONTAL INSTALLATION, cont. Step 1. Determine the desired location of the stove. Check to ensure that wall studs or roof rafters are not in the way when the venting system is attached. If this is the case, you may want to adjust the location of the stove.
  • Page 29 DV425TR DIRECT VENT ROOM HEATER HORIZONTAL INSTALLATION, cont. Step 3. With the adapter and pipe attached to the stove, slide the stove into its correct location, maintaining minimum clearance to combustibles. Mark the wall for a 10” x 10” (254mm x 254mm) square hole. The center of the square hole should line up with the centerline of the horizontal pipe, as shown in Fig.
  • Page 30 DV425TR DIRECT VENT ROOM HEATER HORIZONTAL INSTALLATION, cont. Step 4. Position the horizontal vent termination in the center of the 10” (254mm) square hole, run a bead of non-hardening mastic around its outside edges, so FIG. 7 as to make a seal between it and the wall, attach termination cap to the exterior wall with the four wood screws provided.
  • Page 31 DV425TR DIRECT VENT ROOM HEATER HORIZONTAL INSTALLATION, cont. Note: The attachment from the vent pipe to the vent cap must be siliconed. Venting terminals shall not be recessed into a wall or siding. Step 5. Slide the stove and vent assembly towards the wall, carefully inserting the vent pipe into the vent cap assembly.

  • Page 32: Vertical Installation

    DV425TR DIRECT VENT ROOM HEATER VERTICAL INSTALLATION INSTRUCTIONS USING GS SERIES PIPE FIG. 10 Step 1. Check the installation instructions for required 1” clearances (air space) to combustibles when passing through ceilings, walls, roofs, enclosures, attic rafters, or other nearby combustible surfaces. See page 36, Fig.
  • Page 33 DV425TR DIRECT VENT ROOM HEATER VERTICAL INSTALLATION INSTRUCTIONS, cont. NOTE: Maximum number of 90° elbows permitted for a vertical installation is four, provided the termination falls within the shaded area shown in vent graph on page 33. See also Figure 12 below, within the 4, 90’s configuration, the maximum allowable pipe length on the horizontal runs is 1’, the minimum allowable pipe length on vertical runs is 1’.
  • Page 34 DV425TR DIRECT VENT ROOM HEATER VERTICAL INSTALLATION, cont. Step 4. Assemble the desired lengths of GS pipe and elbows necessary to reach from the stove up through the round support box. Ensure that all pipe and elbow connections are in their fully twist-locked position. Be sure to seal the outer pipe with appropriate sealant (high temperature silicone).

  • Page 35: Roof Pitch Table

    DV425TR DIRECT VENT ROOM HEATER VERTICAL INSTALLATION, cont. Step 7. Continue to assemble pipe sections until the height of the vent cap (H) (Figure 15) meets the minimum code requirements as outlined in Fig. 15 the current CAN/CGA-B149 Installation Codes (in Canada), the National Fuel Gas Code NFPA 54/ANSI Z223.1 (in USA), or local codes.
  • Page 36 DV425TR DIRECT VENT ROOM HEATER VERTICAL INSTALLATION, cont. Step 8. Twist-lock the vent cap and seal. Note: (1) For multi-story vertical installations, a ceiling firestop (SDV part #963) is required at the second floor, and any subsequent floors (Figure 16). The opening should be framed to 10” x 10” (254mm x 254mm) inside dimensions, in the same manner as shown in Figure 13.

  • Page 37: Cathedral Ceiling Installation

    DV425TR DIRECT VENT ROOM HEATER VERTICAL INSTALLATION, cont. CATHEDRAL CEILING INSTALLATION Step 1. Follow installation Steps 1 and 2 under vertical termination section. Figure 17 LEVEL Step 2. CATHEDRAL CEILING Using the plumb-bob, mark the centerline of SUPPORT BOX the venting system on the ceiling, and drill a small hole through the ceiling and roof at this point.
  • Page 38 DV425TR DIRECT VENT ROOM HEATER VERTICAL INSTALLATION, cont. INSTALLATION INTO A CLASS A METAL CHIMNEY (USA ONLY) NOTE: Have the existing installation inspected by a qualified chimney sweep or professional installer prior to converting to direct vent. The existing chimney system must be in serviceable condition and functionally sound and clean.

  • Page 39: Class A Metal Chimney

    DV425TR DIRECT VENT ROOM HEATER VERTICAL INSTALLATION, cont. INSTALLATION INTO A CLASS A METAL CHIMNEY (USA ONLY) Step 4. Pass the flex pipe down through the center of the chimney system, and center the top adapter on the top of the chimney pipe. Drill four 1/8” (3.3mm) diameter holes through the top adapter, and into the chimney top.

  • Page 40: Existing Masonry Chimey

    DV425TR DIRECT VENT ROOM HEATER VERTICAL INSTALLATION, cont. INSTALLATION INTO AN EXISTING MASONRY CHIMNEY (USA ONLY) Step 1. Before cutting any holes, assemble the desired sections of direct vent pipe to determine the center of the masonry penetration. Step 2. Once the center point of the penetration has been determined, cut a 6”...
  • Page 41 DV425TR DIRECT VENT ROOM HEATER VERTICAL INSTALLATION, cont. INSTALLATION INTO AN EXISTING MASONRY CHIMNEY, cont. (USA ONLY) CUT AND BEND FLASHING AS Step 3. NEEDED TO FIT CHIMNEY Secure the flashing (SDV #705C) to the top of the masonry chimney using a bead of non-hardening sealant-adhesive.
  • Page 42 DV425TR DIRECT VENT ROOM HEATER VERTICAL INSTALLATION, cont. INSTALLATION INTO AN EXISTING MASONRY CHIMNEY, cont. (USA ONLY) FLEX LINER Fig. 24 Step 7. If additional lengths of flex liner are needed to span the chimney height, use a flex coupler to connect the pieces of flex liner together.
  • Page 43 DV425TR DIRECT VENT ROOM HEATER VERTICAL INSTALLATION, cont. INSTALLATION INTO AN EXISTING MASONRY CHIMNEY, cont. (USA ONLY) Step 9. Attach the flex to the retro connector. Use 6" DIAMETER OPENING IN MASONRY WALL three sheet metal screws to attach the flex liner to the connector (Figure 26).

  • Page 44: Gas Line Requirements

    DV425TR DIRECT VENT ROOM HEATER GAS LINE REQUIREMENTS The gas line must be installed in accordance monitoring for the odor of either natural gas, which with all local codes, if any; if not, follow ANSI 223.1 will rise, or propane, which will settle near the and the requirements listed below.

  • Page 45: Checking Gas Inlet Pressure

    DV425TR DIRECT VENT ROOM HEATER Gas Line Connection, cont. MANIFOLD PRESSURE TAP INLET PRESSURE TAP VALVE GAS LINE CONNECTION Checking Gas Inlet Pressure Step 1. Turn "ON" all other gas appliances in the household, and; Step 2. Turn the fireplace burner “ON”. Input Pressure Minimum Maximum...

  • Page 46: Leak Test

    DV425TR DIRECT VENT ROOM HEATER LEAK TEST Turn on gas to the fireplace. Turn on gas at the manual shutoff valve. Use a leak detector to leak test all gas joints prior to starting the appliance. Familiarize yourself with the control panel components, see page 56. Follow Lighting Instructions on next page to light the pilot and then the main burner.

  • Page 47: Lighting Instructions

    DV425TR DIRECT VENT ROOM HEATER LIGHTING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot that must be lit manually. When lighting the pilot, follow these instructions exactly B.

  • Page 48: Vertical Damper Adjustment

    DV425TR DIRECT VENT ROOM HEATER VERTICAL DAMPER ADJUSTMENT Refer to Vent Graph on page 27. If your installation falls within the range of the grey shaded area of graph, it may be necessary to make an adjustment to the vertical damper to improve the flame appearance in your stove.

  • Page 49: High Altitude Operation Adjustment

    DV425TR DIRECT VENT ROOM HEATER HIGH ALTITUDE OPERATION Remove front (if installed), glass, and logs (if In Canada, this unit is approved from 0 to 4500 installed.) feet above sea level. Installation of this stove at 2. Remove log/burner pan: First remove screws altitudes above 4500 feet is subject to field test of then lift the front of pan vertically and slide pan to the individual installation and approval by the local...

  • Page 50: Operation

    DV425TR DIRECT VENT ROOM HEATER OPERATION Read this entire manual prior to using the fireplace. Pay particular attention to the “Safety Precautions” section on pages 3-5. Failure to follow the instructions may result in property damage, bodily injury, or even death. PILOT VALVE IGNITOR...

  • Page 51: Maintenance

    DV425TR DIRECT VENT ROOM HEATER MAINTENANCE Installation and repair should be done only by a qualified service person. The appliance should be inspected before use and at least annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, pet hair, et cetera.

  • Page 52: Yearly Maintenance

    DV425TR DIRECT VENT ROOM HEATER YEARLY MAINTENANCE PROCEDURES WARNING! Failure to inspect and maintain the stove may lead to improper combustion and a potentially dangerous situation. The following procedures are recommended to be completed by a qualified technician once per year, preferably prior to the burning season. Check the pilot flame.

  • Page 53: Blower Electrical Wiring

    DV425TR DIRECT VENT ROOM HEATER ELECTRICALSCHEMATICS PILOT ASSEMBLY Ignitor Red (28") RHEOSTAT ON/OFF Switch Red (28") VALVE MALE MOLEX FEMALE PINS 4.00 WHITE CORD SNAP DISC 6.00 BLACK FEMALE MOLEX MALE PINS BLOWER 02/01 Page 53 250-5533...

  • Page 54: Troubleshooting

    DV425TR DIRECT VENT ROOM HEATER TROUBLE SHOOTING Problem: Possible Cause: Solutions: Pilot will not light. Air in Gas Lines. Bleed air from Gas Line. Wrong Inlet Pressure. Check Gas Line pressure (7” Nat., 11” L.P.). Defective Spark Replace Electrode if the Insulator is cracked or the Tip is Electrode.
  • Page 55 DV425TR DIRECT VENT ROOM HEATER TROUBLE SHOOTING (continued) PROBLEM POSSIBLE CAUSE: SOLUTIONS: Pilot will not Hold Defective Magnet If the mV reading is above 6mV and the Safety Magnet does (Cont.) (mV Plus systems). not hold, replace the Valve. (E) If closed-Circuit mV reading is the same as the Open- Circuit reading, the Coil is electrically "Open".
  • Page 56 DV425TR DIRECT VENT ROOM HEATER TROUBLE SHOOTING (continued) Problem: Possible Cause: Solutions: Thermostat/ Excessive Wire Make sure that all mV connections are made using wire of Resistance. the proper size. Wall Switch Valve Wired The Thermo-generator leads must be connected to the will not cycle Incorrectly.

  • Page 57: Parts & Accessories

    DV425TR DIRECT VENT ROOM HEATER PARTS & ACCESSORIES Catalog # DESCRIPTION 844-0640 Quartet Face - Matte Black 844-8650 Quartet Face - Porcelain Black 844-8660 Quartet Face - Porcelain Creme 844-8670 Quartet Face - Porcelain Green 844-8680 Quartet Face - Porcelain Blue 844-8930 Solitaire Face - Matte Black 844-8940...
  • Page 58 DV425TR DIRECT VENT ROOM HEATER NOTES Important! Complete now for future reference. Dovre Sapphire DV425TR Model Name: Serial Number: Date Purchased: Dealership: Dealer Phone: Additional Information: After completing your warranty card, attach your sales receipt and warranty stub here for future reference.

  • Page 59: Warranty

    This limited Lifetime Warranty is effective on all Dovre and Affinity appliances sold after July 1, 1998 and all Quadra-Fire appliances sold after September 1, 1996, and supersedes any and all warranties currently in existence.
  • Page 60 ATTENTION INSTALLER Please return these Operating & Installation Instructions to the Consumer.

Table of Contents