Hide thumbs Also See for 8000TVLP-OAKIPI:
Table of Contents

Advertisement

Quick Links

Para obtener un ejemplar en Español de este
Manual del propietario, visite www.heatnglo.com.
Models:
8000TV-OAK
8000TV-OAK-IPI
8000TVLP-OAKIPI
• Important operating
a n d m a i n t e n a n c e
instructions included.
WARNING: If the information in these
instructions is not followed exactly, a
fi re or explosion may result causing prop-
erty damage, personal injury, or death.
• Do not store or use gasoline or other fl am-
mable vapors and liquids in the vicinity of
this or any other appliance.

• What to do if you smell gas

- Do not try to light any appliance
- Do not touch any electrical switch. Do not
use any phone in your building.
- Immediately call your gas supplier from a
neighbor's phone. Follow the gas suppli-
er's instructions.
- If you cannot reach your gas supplier, call
the fi re department.
• Installation and service must be performed
by a qualifi ed installer, service agency, or the
gas supplier.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer's instructions and
the manufactured home construction and safety standard, Title
24 CFR, Part 3280 or Standard for Installation in Mobile Homes,
CAN/CSA Z240MH.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08
CAUTION
DO NOT DISCARD THIS MANUAL
• Read, understand and follow
these instructions for safe
installation and operation.
Pour demander un exemplaire en français de ce
Manuel du propriétaire, visitez www.heatnglo.com.
Owner's Manual
Installation and Operation
• Leave this manual with
party responsible for use
and operation.
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fi replace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other fl ammable
materials.
• Keep clothing, furniture, draperies and other fl ammable
materials away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fi xed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
In the Commonwealth of Massachusetts:
• installation must be performed by a licensed plumber
or gas fi tter;
• a CO detector shall be installed in the room where the
appliance is installed.
Installation and service of this appliance should be
performed by qualifi ed personnel. Hearth & Home
Technologies suggests NFI certifi ed or factory trained
professionals, or technicians supervised by an NFI
certifi ed professional.
1

Advertisement

Table of Contents
loading

Summary of Contents for Heat & Glo 8000TVLP-OAKIPI

  • Page 1: What To Do If You Smell Gas

    Technologies suggests NFI certifi ed or factory trained This appliance is only for use with the type(s) of gas indicated professionals, or technicians supervised by an NFI on the rating plate. certifi ed professional. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 2 AL TI TUDE : 0-0000 FT . 0000-0000FT . (Modele): MAX. INPU T BTUH: 00,000 00,000 MIN. INPU T BTUH: 00,000 00,000 Serial ORIFICE SIZE: #XXXXX #XXXXX XXXXXXXX (Serie): Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 3: Table Of Contents

    D. Contact Information ......46 = Contains updated information. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 4: Listing And Code Approvals

    Some local building codes require the use of tempered glass with permanent marking in such locations. Glass meeting this requirement is available from the factory. Please contact your dealer or distributor to order. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 5: Non-Combustible Materials Specifi Cation

    A 110-120 VAC circuit for this product must be protected with ground-fault circuit-interrupter protection, compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 6: Getting Started

    • Framing and fi nishing details. See Sections 3, 6 and 11. • Whether optional accessories—devices such as a fan, wall switch, or remote control—are desired. See Section 10. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 7: Negative Pressure

    Consider the fi replace location relative to fl oor and ceiling lowing must be considered: and attic joists. Recommended Recommended Location Location Marginal Location Location Recommended Location NOT Recommended Windward Leeward Multi-level Roofs Figure 2.1 Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 8: Tools And Supplies Needed

    • Read all of the instructions before starting the instal- lation. Follow these instructions carefully during the installation to ensure maximum safety and benefi t. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 9: Framing And Clearances

    In addition to these framing dimensions, also reference the following sections: • Clearances and Mantel Projections (Sections 3.C and 3.D) • Vent Clearances and Framing (Section 6). Figure 3.1 Appliance Locations Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 10: Constructing The Appliance Chase

    Front of Opening Opening Opening Opening to Ceiling Floor Flooring Appliance Appliance Appliance (Vent Pipe) (Height) (Depth) (Width) Inches 40-1/2 1029 1245 Figure 3.2 Clearances to Combustibles Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 11: Mantel Projections

    Figure 3.4 Clearances to Mantel Legs or Wall Projections (Acceptable on both sides of opening.) TOP FRONT EDGE OF FIREPLACE TOP OF HOOD Figure 3.3 Clearances to mantels or other combustibles above appliance Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 12: Termination Locations

    * 3 foot minimum in snow regions Figure 4.1 Minimum height from roof to lowest discharge opening Figure 4.1 specifi es minimum vent heights for various pitched roofs. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 13: Vent Information And Diagrams

    Maximum Total Vertical Rise = 30 Feet Figure 5.2 Maximum Number of Elbows: Two 90 or Four 45 Note: A rise of 1/4 inch per foot of horizontal run is required. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 14 ELBOW 45 DEGREES ADAPT HORIZONTAL LIMITATIONS 90 DEGREES ELBOW Note: Maximum horizontal distance is 50% vertical vent height or up to maximum of 15 feet. Figure 5.3 Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 15: Vent Clearances And Framing

    • Hearth & Home Technologies requires the use of an attic shield. Follow vent pipe manufacturer’s instructions for all clear- ances around pipe. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 16: Appliance Preparation

    • Bend out nailing tabs on each side. • Keep nailing tabs fl ush with the framing. • Secure the appliance to the framing by using nails or screws through the nailing tabs. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 17: Completing Grate Set-Up

    STRAIGHTEN TO REMOVE GRATE REMOVE GRATE REMOVE GRATE BRACKET REMOVE TAB HOLDING DOWN Figure 7.6 BASE REFRACTORY (4 PLACES) Figure 7.4 Removing Grate Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 18: Installing Vent Pipe

    Attach the fi rst B-Vent component to the fl ue outlet collar using 3 self-tapping screws. See Figure 8.1. B-VENT SECURING SCREWS FLUE OUTLET COLLAR Figure 8.1 Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 19: Gas Information

    5.0 inches 11.0 inches Minimum inlet pressure w.c. w.c. 14.0 inches 14.0 inches Maximum inlet gas pressure w.c. w.c. 3.5 inches 10.0 inches Manifold pressure w.c. w.c. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 20 Do NOT change the valve settings. • This valve has been preset at the factory. • Changing valve settings may result in fi re hazard or bodily injury. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 21: Electrical Information

    The wire needs a jacket with a temperature rating of 140º F (60º C) or higher. At the appliance connect the wire to the ON/OFF switch pigtails. Figure 10.1 Standing Pilot Ignition Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 22: Intellifi Re Ignition System Wiring

    Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. WARNING Shock hazard. • Replace damaged wire with type 105º C rated wire. • Wire must have high temperature insulation. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 23: Standing Pilot Ignition System Wiring

    WHITE PILOT PILOT PIEZO THERMOCOUPLE THERMOCOUPLE TEMP SENSOR VALVE VALVE TEMP SENSOR REMOTE RECEIVER THERMOSTAT WIRE ASSEMBLY Figure 10.3 Standing Pilot Ignition Wiring Diagram Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 24: Junction Box Installation

    (1/4 inch male) as shown. Figure 10.5 Junction Box Wired to Wall Switch Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 25: Finishing

    Explosion Risk • Facing and/or finishing materials must never overhang into the glass opening. • Overhanging materials may ignite. • May interfere with proper operation of glass assembly. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 26: Appliance Setup

    PLACE EMBER MATERIAL BETWEEN BACK ROW OF BURNER PORTS AND BACK EDGE OF BURNER. (EMBERS IN THIS AREA WILL CAUSE SOOTING.) EMBER MATERIAL Figure 12.1 Placement of Embers Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 27: Positioning The Logs

    B is located at the back/right corner of burner. NOTE: There should be a 1/2 inch gap between the bottom of log 3 and the top edge of the burner. The underside of log #3 must not cover ANY burner ports. 2057-935C Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 28 6 should rest on the grate bar, centered between tine 4 and 5. NOTE: The front faces (C) of log 6 and 2 should be on the same plane. This is key in avoiding fl ame impingement. NOTE: Finished top view. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 29: Glass Assembly

    Shutter Settings the glass frame. 8000TV-OAK (NG) 1/4 inch 8000TV-OAK-IPI (NG) 1/4 inch 8000TVLP-OAKIPI Fixed LATCHES (BOTH BOTTOM AND TOP) GLASS ASSEMBLY Figure 12.2 Glass Assembly Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 30: Operating Instructions

    fi gure. FLAME OUT appliance and to replace any part of the control system and - BAD - any gas control which has been under water. Figure 13.1 Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 31: Lighting Appliance

    For additional information on operating your Hearth & Home Technologies fi replace, please refer to www.fi replaces.com. Final inspection by Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 32: Standing Pilot Ignition

    OFF”. Do not force. For additional information on operating your Close control access panel. 464-903G Hearth & Home Technologies fi replace, please refer to www.fi replaces.com. Final inspection by Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 33: After Appliance Is Lit

    In an Intellifi re ignition system it is normal to see the pilot fl ame, but it should turn off when continually? ON/OFF is turned off. In a standing pilot system the pilot will always stay on. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 34: Troubleshooting

    Take a reading at the thermopile leads. The read- ing should be 325 millivolts minimum. Replace the thermopile if the reading is below the minimum. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 35 Ensure that the glass is tightened properly on the unit, particularly on top corners. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 36: Intellifi Re Ignition System

    fl ame lifts from pilot hood, the circuit is broken. A wrong orifi ce or too high an inlet pressure can cause pilot fl ame to lift. The sensor rod may be contaminated. Clean sensor rod with emery cloth. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 37 Verify module is securely grounded to metal chassis of appliance. d. Module voltage output / Valve/Pilot Verify battery voltage is at least 2.7 volts. Replace batteries solenoid ohms readings. if voltage is below 2.7. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 38: Maintaining And Servicing Appliance

    • Restricted air fl ow affects burner operation. • Air passageways, grilles, control compartment • Burner, burner ports Risk of: • Fire • Delayed ignition or explosion • Exposure to combustion fumes • Odors Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 39 2. Replace batteries in remote transmitters and battery-powered receivers. 3. Verify batteries have been removed from battery back-up IPI systems to prevent premature battery failure or leaking. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 40: Reference Materials

    ACCESS Location Inches Millimeters Location Inches Millimeters 35-1/2 23-1/2 17-3/4 39-1/4 21-1/2 1091 9-1/2 1221 1015 1-1/8 9-1/8 38-3/4 2-1/4 2-1/4 33-7/8 5-1/4 Figure 16.1 Appliance Dimensions Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 41: Log Set Assembly

    8000TV-OAK, 8000TV-OAK-IPI Service Parts Beginning Manufacturing Date: Feb. 2005 Service Parts Diagram Ending Manufacturing Date: ______ Log Set Assembly Part number list on following page. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 42: Service Parts List

    Pre 002927628 446-505 Pilot Orifi ce NG Post 002927628 593-528 Pre 002927628 446-517 Pilot Orifi ce LP Post 002927628 593-527 Addional service part numbers appear on following page Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 43: Service Parts

    ON/OFF Rocker Switch 060-521A Valve NG 750-500 Valve LP 750-501 Module 593-592 Wire Assembly 593-590A Battery Pack 593-594A 3 Volt Transformer 593-593A 80”& 72” Wire Assembly 522-504A Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 44 Valve NG Post 0021116948 230-0710 060-523 Pre 0021116948 Valve LP 230-0720 Post 0021116948 Piezo Ignitor 291-513 ON/OFF Rocker Switch 060-521A Wire Assembly 049-552A 80” Wire Assembly 522-503A Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 45: Limited Lifetime Warranty

    3. HEAT & GLO reserves the right to make changes at any time, without notice, in design, material, specifi cations and prices of the Product. HEAT & GLO also reserves the right to discontinue styles and products. 060-981E 10/07 © 2007 Hearth & Home Technologies Inc. Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...
  • Page 46: Contact Information

    6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending. Printed in U.S.A. - Copyright 2008 Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. L • 08/08...

This manual is also suitable for:

8000tv-oak-ipi8000tv-oak

Table of Contents